Contents
UK
Safety warnings ..................................................................................................................................................... 3
For the installer ........................................................................................................................................................ 3
For the user .............................................................................................................................................................. 3
Description of the appliance .............................................................................................................................. 4
Extraction mode ....................................................................................................................................................... 4
Recirculation mode .................................................................................................................................................. 4
Control Panel ........................................................................................................................................................ 5
Correct ventilation .................................................................................................................................................... 5
Maintenance and care ......................................................................................................................................... 6
Cleaning the hood .................................................................................................................................................... 6
Metal grease filter .................................................................................................................................................... 6
Removing the metal grease filter ............................................................................................................................. 6
Charcoal filter .......................................................................................................................................................... 7
Changing the light bulb ............................................................................................................................................. 7
What to do if ......................................................................................................................................................... 8
Special accessories* ............................................................................................................................................ 8
Technical Specifications ...................................................................................................................................... 8
Technical assistance service .............................................................................................................................. 9
Guarantee Conditions ....................................................................................................................................... 10
Installation .......................................................................................................................................................... 11
Unpacking .............................................................................................................................................................. 11
Placement .............................................................................................................................................................. 11
Electrical connection .............................................................................................................................................. 11
Wall unit mounting .................................................................................................................................................. 12
Before installing or using this appliance please read this instruction book carefully paying particular attention to
the safety warnings on the following page.
If you have any queries regarding this appliance please contact Customer Care for advice.
Please keep this instruction book for future reference and pass it on to any future owner of the appliance.
2
Safety warnings
For the installer
optimal operation:
— short and straight outlet hose
— keep bends in outlet hose to a minimum
— never install the hoses with an acute angle,
they must always follow a gentle curve.
— keep the hose as large as possible
(preferably the same diameter as the outlet
hole).
— the length should be no more than:
3 metres with one 90° bend
2 metres with two 90° bends
Bends of more than 90° will reduce the
efficiency of the hood and reduce the airflow.
• Failure to observe these basic instructions will
drastically reduce the performance and increase
the noise levels of the extractor hood.
• When used as an extractor unit, the hood must
be fitted with a 150mm diameter hose.
Attention: The hose is not supplied and
must be purchased separately.
• When installing the hood observe the
following minimum distances from the
cooking top:
electric cookers
500 mm
gas cookers
700 mm
The hood can be installed above these heights
but for optimum performance it should be
installed at the distance quoted for the
appropriate heat source.
• The national Standard on fuel-burning systems
specifies a maximum depression of 0.04 mbar in
such rooms.
• The air outlet must not be connected to chimney
flues or combustion gas ducts. The air outlet
must under no circumstances be connected to
ventilation ducts for rooms in which fuel-burning
appliances are installed.
• The air outlet installation must comply with the
regulations laid down by the relevant local
authorities.
• When the unit is used in extraction mode, a
sufficiently large ventilation hole must be
provided, with dimensions that are approximately the same as the outlet hole.
• National and regional building regulations
impose a number of restrictions on using hoods
and fuel-burning appliances connected to a
chimney, such as coal or oil room-heaters and
gas fires, in the same room.
• Hoods can only be used safely with appliances
connected to a chimney if the room and/or flat
(air/environment combination) is ventilated from
outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the
possibility of a depression being created during
operation of the hood.
• If you have any doubts, contact the relevant
controlling authority or building inspector’s
office.
• Since the rule for rooms with fuel burning
appliances is “outlet hole of the same size as the
ventilation hole”, a hole of 500-600 cm2, which
is to say a larger hole, could reduce the performance of the extractor hood.
• If the hood is used in its recirculation mode, it
will operate simply and safely in the above
conditions without the need for any of the
aforementioned measures.
• When the hood is used in its extraction mode,
the following rules must be followed to obtain
3
For the user
• The cooker hood is designed to extract
unpleasant odours from the kitchen, it will not
extract steam.
• Always cover lighted elements, to prevent
excess heat from damaging the appliance. In
the case of oil, gas and coal fired cookers it is
essential to avoid open flames.
• Also, when frying, keep the deep frying pan on
the cooker top/cooker under careful control.
• The hot oil in the frying pan might ignite due to
overheating.
• The risk of self-ignition increases when the oil
being used is dirty.
• It is extremely important to note that
overheating can cause a fire.
• Never carry out any flambé cooking under
the hood.
• Always disconnect the unit from the power
supply before carrying out any work on the
hood, including replacing the light bulb
(take the cartridge fuse out of the fuse holder or
switch off the automatic circuit breaker).
• It is very important to clean the hood and
replace the filter at the recommended
intervals. Failure to do so could cause
grease deposits to build up, resulting in a
fire hazard.
• The appliance is not intended for use by young
children or infirm persons without supervision.
• Older children must be supervised if using the
appliance.
• Young children should be supervised to ensure
that they do not play with the appliance.
• WARNING - Ensure that the appliance is
switched off before replacing the lamp to avoid
the possibility of electric shock.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol
on the product, or on the documents accompanying the product, indicates that this appliance
may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
4
Description of the appliance
• The cooker hood is designed to extract
unpleasant odours from the kitchen, it will
not extract steam.
• The hood is supplied as a recirculator unit and
can also be used in extraction mode by not
installing/using the charcoal filters.
A
Attention! The charcoal filters are attached to one
side of the polystyrene protection panels in the
packaging and should be fitted into place prior to
using the cooker hood in the recirculation mode.
Extraction mode
Fig. 1
• In this mode fumes are extracted to the outside
via a hose connected to the coupling ring A.
Fig. 1.
• In order to obtain the best performance the hose
should have a diameter equal to the outlet hole.
Recirculation mode
• The air is filtered through a charcoal filter and
returned to the kitchen.
• You will need an original charcoal filter for the
recirculation mode. (See Special Accessories).
Control Panel
• Best results are obtained by using a low speed
for normal conditions and a high speed when
odours are more concentrated.
Turn the hood on a few minutes before you start
cooking.
The hood should be left on after cooking for
about 15 minutes or until all the odours have
disappeared. The control switches are located
on the unit bottom.
Light switch
Motor switch
Correct ventilation
Fig. 2
If the cooker hood is to work correctly there must
be an under pressure in the kitchen. It is important
to keep the kitchen windows closed and have a
window in an adjacent room open.
5
Maintenance and care
• The hood must always be disconnected from the electricity supply before beginning any
maintenance work.
Cleaning the hood
Warning
• Clean the outside of the hood using a damp
cloth and a solution of water and mild washing
up liquid.
• Never use corrosive, abrasive or flammable
cleaning products or products containing bleach.
• Never insert pointed objects in the motor’s
protective grid.
• Only ever clean the switch panel and filter grill
using a damp cloth and mild washing up liquid.
• It is extremely important to clean the unit and
change the filters at the recommended intervals.
Failure to do so will cause grease deposits to
build up that could constitute a fire hazard.
• Failure to observe the instructions on cleaning
the unit and changing the filters will cause a fire
hazard. You are therefore strongly
recommended to follow these instructions.
• The manufacturer declines all responsibility for
any damage to the motor or any fire damage
linked to inappropriate maintenance or failure to
observe the above safety recommendations.
Metal grease filter
• The purpose of the grease filters is to absorb
grease particles which form during cooking and
it must always be used, either in the external
extraction or internal re-circulation function.
Attention: the metal grease filters must be
removed and washed, either by hand or in the
dishwasher, every four weeks.
Removing the metal grease
filters
• Push it towards the back of the unit and then
pull it down and out.Fig. 3.
Hand washing
Soak grease filters for about one hour in hot
water with a grease-loosening cleaner, then
rinse off thoroughly with hot water. Repeat the
process if necessary. Refit the grease filters
when they are dry.
Dishwasher
Place grease filters in the dishwasher. Select
most powerful washing programme and highest
temperature, at least 65°C. Repeat the process.
Refit the grease filters when they are dry.
When washing the metal grease filter in the
dishwasher a slight discolouration of the filter
can occur, this does not have any impact on its
performance.
• Clean the inner housing using a hand hot
solution only(never use caustic detergents,
abrasive powders or brushes).
Fig. 3
6
Charcoal filter
• The charcoal filter should only be used if you
want to use the hood in recirculation mode.
• To do this you will need an original charcoal
filter (available from your local Service Force
Centre).
• Cleaning/replacing the charcoal filter
Unlike other charcoal filters, the LONGLIFE
charcoal filter can be cleaned and reactivated.
With normal use the filter should be cleaned
every second month (when using the hood 2,5
hours per day,on avarage). The best way to
clean the filter is in the dishwasher. Use normal
detergent and choose the highest temperature (65º C). Wash the filter separately so
that no food particles get stuck on the filter
and later causes bad odours. To reactivate
the charcoal, the filter should be dried in
an oven for 10 minutes with a maximum
temperature of 100º C.
After approximately three years of use, the
charcoal filter should be replaced with a new, as
the odour reduction capacity will be reduced.
• Fitting
Remove the frame i which supports the filter h
by turning 90° the two knobs g.
Insert the charcoal filter inside the frame and
put all parts back in their place. Fig. 4.
• To remove proceed in the reverse order.
• Always specify the hood model code number
and serial number when ordering replacement
filters. This information is shown on the rating
plate located on the inside of the unit.
• The charcoal filter can be ordered from your
local Service Force Centre.
g
j
g
i
g
h
Fig. 4
Changing the light bulb
• Disconnect the cooker hood from the mains
electricity supply.
• Extract the lamp, the lamp support and its
connector A, carefully use a flat bladed
screwdriver as a lever. Fig. 5.
• Replace the old bulb with a new one of the
same type.
• If the light does not come on, make sure the
bulb has been inserted correctly before
contacting your local Service Force Centre.
a
Fig. 5
7
g
What to do if
If your appliance fails to work properly please carry out the following checks.
Symptom
Solution
The cooker hood will not start...
Check that: The hood is connected to the electricity supply.
Check that a fan speed has been selected
The cooker hood is not working
Check that: The fan speed is set high enough for the task.
The grease filters are clean.
The kitchen is adequately vented to allow the entry of fresh air.
If set up for recirculation, check that the charcoal filter is still effective.
If set up for extraction, check that the ducting and outlets are not
blocked.
The cooker hood has
switched off during operation...
The safety cut-out device has been tripped.
Turn off the hob and then wait for the device to reset.
If the hood has been installed below the heights indicated in the
installation instructions the motor will cut-out frequently which will
damage the hood.
If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and
serial number.
Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a
charge if the fault is not a mechanical or electrical breakdown.
Special Accessories
Charcoal Filter Type 20
Technical Specifications
Model
Dimensions (in cm):
Height
Width
Depth
Maximum absorbed power:
Motor absorption:
Lighting:
Length of the cable:
Electrical connection:
Fuse rating:
ZHC 955
81,5 - 112,5
89,8
50,1
200 W
170 W
2 x 20 W
150 cm
220-240 V
5A T
Subject to change without notice.
8
Technical assistance service
You are welcome to telephone our technical assistance service (see list of technical assistance centres)
whenever you need information or in the unlikely event of a fault.
For service in Australia call 1300 650 020.
When calling, please be ready to specify:
1.
The model code number
2.
The serial number (E-Nr.)
3.
The manufacturing number (F-Nr.)
This information is shown on the registration plate inside the unit behind the grease filter.
We reserve the right to change specifications and colours as a result of our policy of continuing technological
development.
Service and Spare Parts UK
In the event of your appliance requiring service, or if you wish to purchase spare parts, contact your local
Service Force Centre by telephoning: 08705 929 929
Your call will be automatically routed to the Service Centre covering your post code area. For the address of
your local Service Force Centre and further information about Service Force, please visit the website at
www.serviceforce.co.uk
Please ensure that you have read the section „What to do if....“ as the engineer will make a charge if the fault is
not a mechanical or electrical breakdown even the appliance is under warranty. Please note that proof of
purchase is required for in-guarantee service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
• Your name
• Clear and concise details of the fault
• Address and post code
• Name and model of the appliance*
• Telephone number
• E number*
• Serial number*
* This information can be found on the rating plate, which can be seen when the grease filters are removed.
If you require Customer Service in the Republic of Ireland please contact us at the address below:
Electrolux
Electrolux Group (Ire) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0) 1 4090751
Email: service.eid@electrolux.ie
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please
contact our Customer Care Department by letter or telephone at the address below or visit our website at
www.electrolux.co.uk
Customer Services Department
Major Appliances
Zanussi
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 727 727 (*)
* calls to this number may be recorded for training purposes.
9
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 24 months of the date of the purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
All service work under this guarantee must be undertaken by an Zanussi Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday.
Visits may be available outside these hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
European Community (EC) or European Free Trade Area.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of
use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within the European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal
household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Sweden
UK
Senlis
Nürnberg
Pordenone
Stockholm
Luton
+33 (0)3 44 62 20 13
+49 (0)800 234 7378
+39 (0) 800 117511
+46 (0)20 78 77 50
+44 (0) 8705 727 727
10
Installation
Unpacking
Check that the cooker hood has no damages.
Transportation damages should immediately be
reported to the company responsible for the
transportation.
Damages, faults and eventually missing details
should immediately be reported to the retailer.
Take care of the packing materials so that small
children cannot play with them.
Location
The hood is to be mounted on the wall.
When installed, the hood must be not less than
50cm. above electric burners or 70 cm. above gas
or mixed-fuel burners.
Electrical connection
(not for UK)
Safety warnings for the electrician
Before connecting the appliance to the power
supply, check that the voltage indicated on the
rating plate corresponds to the mains power supply
available. Appliances fitted with a plug can be
connected to any standard power socket within
easy access.
Should it be necessary to provide a fixed
connection, the hood must only be installed by an
electrician authorised by the local electricity board.
When installing, an omnipolar disconnector with a
distance of at least 3 mm between contacts must
be provided.
Fixed connection of the appliance must only be
carried out by an authorised electrician.
Electrical connection for UK
only
Safety warnings for the electrician
Connect the hood to the mains supply via a double
pole switch which has 3 mm minimum separation
between the contacts.
The switch must be accessible at all times.
The following is valid in the United Kingdom only:
- the wire which is coloured green and yellow
must be connected to the terminal which is
marked with the letter E or by the earth symbol
(
), or coloured green or green and yellow;
- the wire which is coloured blue must be
connected to the terminal which is marked with
the letter N or coloured black, - the wire which is coloured brown must be
connected to the terminal which is marked with
the letter L or coloured red.
11
Installation
Mounting accessories included
1 deflector (+ spacers adapter)
2 metal screws 3,5 x 13 (to fix spacers adapter to
deflector).
2 metal screws 3 x 9 (to fix upper chimney
section)
12 metal screws 3,5 x 9,5 (6 to fix motor unit to
lower part of the hood, 4 to fix deflector to
chimney support, 2 to fix lower chimney
section)
1 chimney support (3 pieces to assemble)
4 metal screws 4 x 8 (to assemble the chimney
support)
5 wood-screws 5 x 45 mm (for wall mounting)
5 wall plugs Ø 8 mm (for wall mounting)
1 allen spanner (for TORX 10/20 screws)
1 support bracket
Assembling the chimney flue
support/bracket (3 parts):
=
G
The three parts should be fixed with 4 screws,
the support extension is adjustable and should
correspond to the internal width of the
telescopic chimney flue. Fig. 6.
=
X
=
X
=
F
X
Assembling the deflector
H
(3 parts – only for recirculation
mode):
The three parts should be fixed with 2 screws,
the deflector extension is adjustable and should
correspond to the width of the chimney flue
support, to which it is then fixed. Fig. 6.
Fig. 6
12
F
G
Wall unit mounting - Fig. 7-8-9
Disconnect the hood during electrical connection,
by turning the home mains switch off.
Remove the grease filter.
• Rest the motor unit on a flat surface and thread
the lower part of the hood onto it (1).
• Make all the electrical connections between the
two parts (2).
• Secure the two parts using 12 screws (3).
• Mark the wall with a centre line, this will aid the
fixing procedure (4), position the template so
that the mid line printed on the template
matches with the centre line previously marked,
the lower side of the template corresponds to
the lower side of the hood once installed (5).
• Drill two holes Ø 8mm and fix the support
bracket with two wall plugs and screws (6).
• Hang the hood (7) adjust its position (8-9) and
from the inside of the hood mark one point for
final fixing (10), remove the hood (11) and drill
an hole Ø 8mm (12), fit a wall plugs (13).
• Drill two holes Ø 8mm on the upper side close
to the ceilling (14), fit two wall plugs and fix the
chimney support with two screws (15).
• Hang the hood again (16).
• Fix it securely with a screw (17). To simplify
the installation operation remove the charcoal
filter frame.
• If the hood is used in the recirculation
function, fix the deflector F on the chimney
support G with four screws and fit an extraction
pipe (18 - not supplied) to connect deflector to
the outlet hole B of the hood.
In case the hood is to be used in exhausting
version, then the deflector must not be mounted
and fit an extraction pipe (18) to connect outlet
hole B of the hood to the outside.
• Make the electrical connection (19), but leave
the hood disconnected from the household
mains supply.
• Fix the chimney (20a) to the chimney support
(20b) slide downwards (21) and , from the
inside the of the hood (22).
Slide down the lower section on the proper housing
on top of the hood. Refit the grease filter.
Connect the hood to the household mains supply
and check that the hood works correctly.
13
2
2
1
Fig. 7
x12
3
20a
20a
H
14
G
14
20b
G
15
20b
7-16
9
19
7-16
11
21
F
4
11
18
6
8
5
B
9
8
9
8
13
12
10
17
Fig. 8
22
Fig. 9
14
22
15
LI2LDD Ed. 02/06