APPENDIX
SCHEMATIC
Attachment
MANDREL
found inside attachment
Bit Release Key
Feed Pawl Lever
(Must be engaged
in Feed Pawl
Assembly Slot)
Feed Pawl Assembly
Part #:
PMANDREL65 (QDPRO200G2, QDPROLDHG2,
QDPROPHG2)
PMANDREL75 (QD200SG2, QDPRO250G2,
QDPRO300SG2, QDPRORFG2, QDPRO300RFG2,
QDHSD60, QDHSD75, QD2000SDS)
PMANDREL158 (QDA158, QDA158G2,
QDA158NS)
TROUBLE SHOOTING GUIDE
PROBLEM
SOLUTION
Screws won’t drive.
They spin for a second, then lay over
on their side. Little or no penetration.
Make sure the screwgun is not in reverse.
Screws won’t drive completely.
They go down about halfway,
then the bit spins out.
Check to be sure you are using the correct bit for the type of screws you are driving.
Check for bit wear. It may be time to install a new bit.
Push harder when driving.
Screws won’t drive completely.
They are almost completely driven but
won’t countersink completely.
Check the depth adjustment on the attachment. Reset if necessary.
You may have missed the substrate.
Example: In flooring, this will occur if you miss the joist.
Screws don’t advance properly
causing tool to jam.
Use only Quik Drive brand collated screws.
Be sure the screw strip is inserted correctly - pointed end first.
Lift the tool completely off the work surface after driving each screw.
Don’t drag screw strips on the work surface as you move to the next position.
Be sure the feed pawl assembly is intact and feed lever is engaged.
FASTENER “RULES OF THUMB” FOR MAJOR APPLICATIONS
SUBFLOOR
Approximately 1900 WSNTL screws per 1000 square feet of subfloor, assuming the diaphragm is UNBLOCKED and screw spacing
is 4" O.C at the boundaries and 8" O.C. in the field. For blocked diaphragm, increase the number of screws by 75%.
DECK
Typically two screws at each deck board/joist intersection, approximately 300-400 screws
per 100 square feet depending on joist spacing.
DRYWALL
Approximately 34 screws per 4X8 sheet.
54
C-QD06-R © 2006 SIMPSON STRONG-TIE CO., INC.
Quik Drive® tools are easy to use. As with any power tool, there are a few basic things to remember for best performance.
APPENDIX
ADAPTORS FOR MOST POPULAR SCREWGUNS
SCREWGUN
AEG
SE4000
ADAPT0R
SCREWGUN
MIAG2
Hilti ST 18
SF4000
®
Aro®
SG052B-25 ARO-SG052B
Atlas Copco®
PRO2000 MIAG2
Bosch®
1423VSR
1404VSR
1405VSR
DeWalt 251
252
254
255
257
260
265
266
267
268
269
272
274
275
276
277
284
ADAPT0R
BOAG2
BOAG2
BOAG2
®
N/A
DWAG2
DWAG2
DWAG2
DWAG2
DWAG2
DWAG2
DWAG2
N/A
N/A
N/A
DWAG2
DWAG2
DWAG2
DWAG2
DWAG2
DWAG2
SCREWGUN
Metabo SE 5025
SE 5040
Hitachi®
Milwaukee®
W6V3
HIAG2
6580-20
W8VB
HIAG2
6581-20
6582-1
Makita®
6583-1
6801DVB
MAAG2**
6708-21
6802VB
MAAG2**
6707-20
6807
MAAG2**
6701-20
6820V
MAAG2
6702-20
6821
ADM21G2
6740-20
6823Z
MAAG2
6741-1
6823N&TP MAAG2
6742-20
6824 MAAG2
6743-20
6825
MAAG2
6743-50
6827
ADM27G2
6743-55
6828
MAAG2
6744-1
6831D
ADM31DG2** 6745-1
6746-1
6832
ADM31G2
6747-1
6833D
ADM31G2
6749-1
6834
ADM34G2
6835D
ADM34G2
6755-4
6758
6759
6760
Masterpower®
6790-1
2460-m
MPAG2
6791-20
2461-m
MPAG2
6798-1
®
ADAPT0R
SCREWGUN
HT18G2
HTAG2
ADAPT0R
Porter Cable 4630
PCAG2
4634
PCAG2
4640 PCAG2
6640
PCA6645G2
6641
PCA6645G2
6645
PCA6645G2
2640
N/A
®
®
MEAG2
MEAG2
MIL65G2
N/A
N/A
N/A
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
MIAG2
N/A
MIAG2
MIAG2
N/A
N/A
MIAG2
MIAG2
N/A
MIAG2
MIAG2
MIAG2
N/A
Sioux®
2P2603A
2P2303A
2S2303A
SXAG2
SXAG2
SXAG2
AEG® is a trademark of
AEG Electrowerkzenge
ARO® is a trademark of Ingersoll-Rand Company, LTD.
Atlas Copco® is a trademark of
Atlas Copco AB
Bosch® is a trademark of
Bosch Tool Corporation
Hilti® is a trademark of
Hilti Corporation
Hitachi® is a trademark of
Hitachi Koki Co., LTD.
Masterpower® is a trademark of
Cooper Industries, Inc.
Metabo® is a trademark of
Metabowerke GmbH
Milwaukee® is a trademark of
Milwaukee Electric Tool Corporation
Sioux® is a trademark of
Sioux Tools, Inc.
DeWalt® is a trademark of DeWalt
Industrial Tool, Co.
Makita® is a trademark of Makita
Corporation
Porter Cable® is a trademark of
DeWalt Industrial Tool, Co.
C-QD06-R © 2006 SIMPSON STRONG-TIE CO., INC.
**May require slight modification
CURVED COLLATION
Quik Drive Patented Collation
• Easier toenailing
• Easier to move between driving locations without drag
• Strip is pointed at leading end for easy loading
See pages 6, 7 for corrosion information.
55