Zenith XBV613 Series Service manual

SERVICE MANUAL
SERVICE MANUAL
Model Series:
MODEL : XBV613
Product Type: VCR+DVD COMBI
Chassis: D37 + DP-10C
Manual Series: XBV613
Manual Part #: 3829RGN005G
Model Line: D
Product Year: 2006
XBV613
CONTENTS
SUMMARY ................................................
CABINET & MAIN CHASSIS ....................
ELECTRICAL ............................................
MECHANISM OF VCR PART ...................
REPLACEMENT PARTS LIST ..................
1
2
3
4
5
Published March 2006
by Technical Publications
Zenith Electronics Corporation
201 James Record Road
Huntsville, Alabama 35824-1513
Copyright © 2006 by Zenith Electronics Corporation
Printed in U.S.A
CONTENTS
SECTION
SECTION
SECTION
SECTION
SECTION
1
2
3
4
5
. . . . SUMMARY
. . . . CABINET & MAIN CHASSIS
. . . . ELECTRICAL
. . . . MECHANISM OF VCR PART
. . . . REPLACEMENT PARTS LIST
SECTION 1
SUMMARY
CONTENTS
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS ............. 1-3
SERVICING PRECAUTIONS .................................................................................................. 1-4
• General Servicing Precautions
• Insulation Checking Prodedure
• Electrostatically Sensitive Devices
SERVICE INFORMATION FOR EEPROM ........................................................................... 1-5
SPECIFICATIONS ....................................................................................................................... 1-6
PRODUCT SAFETY SERVICING GUIDELINES FOR VIDEO PRODUCTS
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN ANY WAY,
NEVER PERFORM CUSTOMIZED INSTALLATIONS WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED MODIFICATIONS WILL NOT ONLY
VOID THE WARRANTY, BUT MAY LEAD TO YOUR BEING LIABLE FOR ANY
RESULTING PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU ARE
THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING SAFETY
CHECKS AND SERVICING GUIDELINES. TO DO OTHERWISE,
INCREASES THE RISK OF POTENTIAL HAZARDS AND INJURY TO THE
USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR PROTECTION FROM A.C. LINE SHOCK.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN CORRECTED. A
CHECK SHOULD BE MADE OF THE FOLLOWING.
SUBJECT : FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN SUCH A WAY
AS TO AVOID POSSIBILITY OF ADJACENT COMPONENT SHORTS.
THIS IS ESPECIALLY IMPORTANT ON THOSE MODULES WHICH ARE
TRANSPORTED TO AND FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE DEVICES
SUCH AS INSULATORS, BARRIERS, COVERS, SHIELDS, STRAIN
RELIEFS, POWER SUPPLY CORDS, AND OTHER HARDWARE HAVE
BEEN REINSTALLED PER ORIGINAL DESIGN. BE SURE THAT THE
SAFETY PURPOSE OF THE POLARIZED LINE PLUG HAS NOT BEEN
DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE COLD
SOLDER JOINTS, SOLDER SPLASHES OR SHARP SOLDER POINTS.
BE CERTAIN TO REMOVE ALL LOOSE FOREIGN PARTICLES.
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR DETERIORATION
TO PARTS AND COMPONENTS. FOR FRAYED LEADS, DAMAGED
INSULATION (INCLUDING A.C. CORD). AND REPLACE IF NECESSARY
FOLLOW ORIGINAL LAYOUT, LEAD LENGTH AND DRESS.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECIVING TUBE OR
A RESISTOR RATED AT 1 WATT OR MORE. LEAD TENSION AROUND
PROTRUNING METAL SURFACES MUST BE AVOIDED.
6. ALL CRITICAL COMPONENTS SUCH AS FUSES, FLAMEPROOF
RESISTORS, CAPACITORS, ETC. MUST BE REPLACED WITH EXACT
FACTORY TYPES, DO NOT USE REPLACEMENT COMPONENTS
OTHER THAN THOSE SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT MODIFICATIONS.
7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN A.C.
LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF THE CABINET, (THE CHANNEL SELECTOR KNOB, ANTENNA TERMINALS. HANDLE AND SCREWS) TO BE SURE THE SET IS SAFE TO OPERATE
WITHOUT DANGER OF ELECTRICAL SHOCK. DO NOT USE A LINE
ISOLATION TRANSFORMER DURING THIS TEST USE AN A.C. VOLTMETER, HAVING 5000 OHMS PER VOLT OR MORE SENSITIVITY, IN
THE FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT RESISTOR, PARALLELED BY A .15 MFD. 150.V A.C TYPE CAPACITOR
BETWEEN A KNOWN GOOD EARTH GROUND (WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED METALLIC PARTS, ONE AT A TIME.
MEASURE THE A.C. VOLTAGE ACROSS THE COMBINATION OF 1500
OHM RESISTOR AND .15 MFD CAPACITOR. REVERSE THE A.C. PLUG
AND REPEAT A.C. VOLTAGE MEASUREMENTS FOR EACH EXPOSED
METALLIC PART. VOLTAGE MEASURED MUST NOT EXCEED 75
VOLTS R.M.S. THIS CORRESPONDS TO 0.5 MILLIAMP A.C ANY
VALUE EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL SHOCK
HAZARD AND MUST BE CORRECTED IMMEDIATELY.
A.C. VOLTMETER
GOOD EARTH GROUND
SUCH AS THE WATER
PIPE. CONDUIT. ETC
PLACE THIS PROBE
ON EACH EXPOSED
METAL PART
SUBJECT: GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH APROWHEAD SYMBOL. WITHIN
AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE
SERVICE PERSONNEL TO THE PRESENCE OF UNINSULATED
“DANGEROUS VOLTAGE” THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE SERVICE PERSONNEL TO
THE PRESENCE OF IMPORTANT SAFETY INFORMATION IN
SERVICE LITERATURE.
SUBJECT : X-RADIATION
1. BE SURE PROCEDURES AND INSTRUCTIONS TO ALL SERVICE PERSONNEL COVER THE SUBJECT OF X-RADIATION. THE ONLY POTENTIAL SOURCE OF X-RAYS IN CURRENT T.V. RECEIVERS IS THE PICTURE TUBE. HOWEVER, THIS TUBE DOES NOT EMIT X-RAYS WHEN
THE HIGH VOLTAGE IS AT THE FACTORY SPECIFIED LEVEL. THE
PROPER VALUE IS GIVEN IN THE APPLICABLE SCHEMATIC. OPERATION AT HIGHER VOLTAGES MAY CAUSE A FAILURE OF THE PICTURE TUBE OR HIGH VOLTAGE SUPPLY AND, UNDER CERTAIN CIRCUMSTANCES, MAY PRODUCE RADIATION IN EXCESS OF DESIRABLE LEVELS.
2. ONLY FACTORY SPECIFIED C.R.T. ANODE CONNECTORS MUST BE
USED. DEGAUSSING SHIELDS ALSO SERVE AS X-RAY SHIELD IN
COLOR SETS, ALWAYS RE-INSTALL THEM.
3. IT IS ESSNTIAL THAT SERVICE PERSONNEL HAVE AVAILABLE AN
ACCURATE AND RELIABLE HIGH VOLTAGE METER. THE CALIBRA
TION OF THE METER SHOULD BE CHECKED PERIODICALLY
AGAINST A REFERENCE STANDARD, SUCH AS THE ONE AVAILABLE
AT YOUR DISTRIBUTOR.
4. WHEN THE HIGH VOLTAGE CIRCUITRY IS OPERATING PROPERLY
THERE IS NO POSSIBILITY OF AN X-RADIATION PROBLEM. EVERY
TIME A COLOR CHASSIS IS SERVICED. THE BRIGHTNESS SHOULD
BE RUN UP AND DOWN WHILE MONITORING THE HIGH VOLTAGE
WITH A METER TO BE CERTAIN THAT THE HIGH VOLTAGE DOES
NOT EXCEED THE SPECIFIED VALUE AND THAT IT IS REGULATING
CORRECTLY, WE SUGGEST THAT YOU AND YOUR SERVICE ORGANIZATION REVIEW TEST PROCEDURES SO THAT VOLTAGE REGULATION IS ALWAYS CHECKED AS A STANDARD SERVICING PROCEDURE. AND THAT THE HIGH VOLTAGE READING BE RECORDER ON
EACH CUSTOMER’S INVOICE.
5. WHEN TROUBLESHOOTING AND MAKING TEST MEASUREMENTS IN
A PRODUCT WITH A PROBLEM OF EXCESSIVE HIGH VOLTAGE,
AVOID BEING UNNECESSARILY CLOSE TO THE PICTURE TUBE AND
THE HIGH VOLTAGE SUPPLY. DO NOT OPERATE THE PRODUCT
LONGER THAN IS NECESSARY TO LOCATE THE CAUSE OF EXCES
SIVE VOLTAGE.
6. REFER TO HV. B+ AND SHUTDOWN ADJUSTMENT PROCEDURES
DESCRIBED IN THE APPROPRIATE SCHEMATIC AND DIAGRAMS
(WHERE USED).
SUBJECT: IMPLOSION
1. ALL DIRECT VIEWED PICTURE TUBES ARE EQUIPPED WITH AN INTE
GRAL IMPLOSION PROTECTION SYSTEM, BUT CARE SHOULD BE
TAKEN TO AVOID DAMAGE DURING INSTALLATION, AVOID
SCRATCHING THE TUBE. IF SCRATCHED REPLACE IT.
2. USE ONLY RECOMMENDED FACTORY REPLACEMENT TUBES.
SUBJECT : TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS, CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER OR CLOSE TO
HEAT DUCT, OR IN THE PATH OF HEATED AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS: OUTDOOR PATIO
INSTALLATIONS WHERE DEW IS A FACTOR, NEAR STEAM RADIATORS WHERE STEAM LEAKAGE IS A FACTOR, ETC.
3. AVOID PALCEMENT WHERE DRAPERIES MAY OBSTRUCT REAR
VENTING. THE CUSTOMER SHOULD ALSO AVOID THE USE OF DECORATIVE SCARVES OR OTHER COVERINGS WHICH MIGHT
OBSTRUCT VENTILATION.
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A COMMERCIAL MOUNTING KIT. MUST FOLLOW THE FACTORY APPROVED
MOUNTING INSTRUCTIONS A PRODUCT MOUNTED TO A SHELF OR
PLATFORM MUST RETAIN ITS ORIGINAL FEET (OR THE EQUIVALENT
THICKNESS IN SPACERS) TO PROVIDE ADEQUATE AIR FLOW
ACROSS THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS
MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM LEAKAGE
TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A PRODUCT ON
SLOPING SHELF OR A TILTED POSITION, UNLESS THE PRODUCT IS
PROPERLY SECURED.
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE ON ITS
MOUNTING TO THE CART. CAUTION THE CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART WITH SMALL CASTERS ACROSS
THRESHOLDS OR DEEP PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR STAND
WHICH HAS NOT BEEN LISTED BY UNDERWRITERS LABORATORIES,
INC. FOR USE WITH THEIR SPECIFIC MODEL OF TELEVISION
RECEIVER OR GENERICALLY APPROVED FOR USE WITH T.V.’S OF
THE SAME OR LARGER SCREEN SIZE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION CORDS,
EXPLAIN THAT A FOREST OF EXTENSIONS SPROUTING FROM A SINGLE OUTLET CAN LEAD TO DISASTROUS CONSEQUENCES TO
HOME AND FAMILY.
1-3
SERVICING PRECAUTIONS
CAUTION : Before servicing the VCR+DVD covered by this
service data and its supplements and addends, read and follow the SAFETY PRECAUTIONS. NOTE : if unforeseen circumstances create conflict between the following servicing
precautions and any of the safety precautions in this publications, always follow the safety precautions.
Remembers Safety First:
General Servicing Precautions
1. Always unplug the VCR+DVD AC power cord from the AC
power source before:
(1) Removing or reinstalling any component, circuit board,
module, or any other assembly.
(2) Disconnection or reconnecting any internal electrical
plug or other electrical connection.
(3) Connecting a test substitute in parallel with an electrolytic capacitor.
Caution : A wrong part substitution or incorrect
polarity installation of electrolytic capacitors may result
in an explosion hazard.
2. Do not spray chemicals on or near this VCR+DVD or any
of its assemblies.
3. Unless specified otherwise in this service data, clean
electrical contacts by applying an appropriate contact
cleaning solution to the contacts with a pipe cleaner,
cotton-tipped swab, or comparable soft applicator.
Unless specified otherwise in this service data, lubrication
of contacts is not required.
4. Do not defeat any plug/socket B+ voltage interlocks with
whitch instruments covered by this service manual might
be equipped.
5. Do not apply AC power to this VCR+DVD and/or any of its
electrical assemblies unless all solid-state device heat
sinks are cerrectly installed.
6. Always connect test instrument ground lead to the
appropriate ground before connection the test instrument
positive lead. Always remove the test instrument ground
lead last.
Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet and turn
the power on. Connect an insulation resistance meter(500V)
to the blades of the attachment plug. The insulation resistance between each blade of the attachment plug and accessible conductive parts (Note 1) should be more than 1Mohm.
Note 1 : Accessible Conductive Parts including Metal panels, Input terminals, Earphone jacks, etc.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged
easily by static electricity. Such components commonly are
called Electrostatically Sensitive (ES) Devices. Examples of
typical ES devices are integrated circuits and some field
effect transistors and semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known
earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which
should be removed for potential shock reasons prior to
applying power to the unit under test.
2. After removing an electrical assembly equipped with ES
devices, place the assembly on a conductive surface such
as aluminum foil, to prevent electrostatic charge buildup or
exposure of the assembly.
3. Use only a grouned-tip soldering iron to solder or unsolder
ES devices.
4. Use only an anti-static solder removal device. Some
solder removal devices not classified a “anti-static” can
generate electrical charges sufficient to damage ES
devices.
5. Do not use freon-propelled chemicals. These can
generate electrical charge sufficient to damage ES
devices.
6. Do not remove a replacement ES device from its protec
tive package until immediately before you are ready to
install it. (Most replacement ES devices are packaged with
leads electrically shorted together by conductive foam,
aluminum foil, or comparable conductive material).
7. Immediately before removing the protective material from
the leads of a replacement ES device, touch the protective
material to the chassis or circuit assembly into which the
device will be installed.
Caution : Be sure no power is applied to the chassis or
circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged
replacement ES devices. (Normally harmless motion such
as the brushing together of your clothes fabric or the lifting
of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.)
1-4
SERVICE INFORMATION FOR EEPROM
POWER ON
DVD LOGO Status (NO Disk status)
Remotecontrol
Pause key-->1-->4-->7-->2 in order.
Press number 0~9, Press charater
A~F (1~6 for a while)
Use arrow key (F D G E) to move
to approprite position and make
changes
Press pause key once
DETECT NEW EEPROM
(OPTION EDIT SCREEN)
MODEL XBV613
NAME HEX
OPT 1
OPT 2
OPT 3
OPT 4
OPT 5
OPT 6
OPT 7
OPT 8
OPT 9
OPT A
OPT B
OPT C
OPT D
OPT E
OPT F
OPT G
55
53
00
45
12
05
E4
00
00
00
C0
40
A0
01
03
3D
Change will be applied when power
OFF-->ON.
* OPTION
• NTSC model doesn’t have VCR option and use DVD option B~F as VCR option. (only DVD exist)
• PAL model has another separate VCR option. (Both VCR and DVD exist)
1-5
SPECIFICATIONS
• GENERAL
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
120V, 60Hz
16 W
430 x 78.5 x 265 mm (W x H x D)
4.2 kg
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
• INPUTS
ANTENNA IN
VHS VIDEO IN(LINE1, 2)
VHS AUDIO IN(LINE1, 2)
75 ohms (VHF/UHF/CATV)
1 V (p-p) 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2
•OUTPUTS
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
RF OUT
1 V (p-p) 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.286 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1
Channel 3 or 4 (Adjustable)
• VCR SPECIFICATIONS
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/
8 HOURS (T-160)
About 3 minutes (T-120)
VHF: 2-13, UHF: 14-69,
CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20 Hz to 20 kHz
More than 43 dB
More than 88 dB
More than 60 dB
• DVD SPECIFICATIONS
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz,
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100 dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (DVD/CD)
*Design and specifications are subject to change without notice.
1-6
SECTION 2
CABINET & MAIN CHASSIS
CONTENTS
EXPLODED VIEWS .....................................................................................................................2-2
1. Cabinet and Main Frame Section ...........................................................................................2-2
2. DECK MECHANISM SECTION [ DVD MD (DP-10C) ] ............................................................2-3
3. Packing Accessory Section ....................................................................................................2-4
2-1
EXPLODED VIEWS
1. CABINET AND MAIN FRAME SECATION
463
NOTES) THE EXCLAMATION POINT WITHIN AN
EQUILATERAL TRIANGLE IS INTENDED
TO ALERT THE SERVICE PERSONNEL
TO THE PRESENCE OF IMPORTANT
SAFETY INFORMATION IN SERVICE
LITERATURE.
322
323
A47
330
463
465
261
452
A44
285
286
260
283
2
452
284
261
271
A26
272
273
452
261
A50
469
463
3
CN501
469
463
274
288
471
300
250
4
324
A00
457
470
469
A46
463
5
A
A43
280
1
B
C
2-2
D
2. DECK MECHANISM SECTION [ DVD MD (DP-10C) ]
A26
001
A01
002
A02
439
003
018
013
014
020
017
435
012
015
015B
016
015A
019
012A
432
440
026
012
030
010
024
439
025
431
435
036
012A
021
A03
430
2-3
3. PACKING ACCESSORY SECTION
810 CABLE ASS'Y RF
806 RF CABLE
808 BATTERY
REMOTE CONTROLLER
900 ASSEMBLY
811
PLUG ASS'Y 1WAY
812
PLUG ASS'Y 2WAY
801 INSTRUCTION ASSEMBLY
804 BAG
803 PACKING, CASING
803 PACKING, CASING
802 BOX
2-4
SECTION 3
ELECTRICAL
CONTENTS
VCR PART
ELECTRICAL ADJUSTMENT
PROCEDURES.......................................................3-2
DVD PART
ELECTRICAL
TROUBLESHOOTING GUIDE ........................3-57
1. POWER CHECK FLOW ..................................3-57
2. SYSTEM OPERATION FLOW.........................3-58
3. TEST & DEBUG FLOW ...................................3-59
ELECTRICAL
TROUBLESHOOTING GUIDE ..........................3-3
1. POWER(SMPS) CIRCUIT..................................3-3
2. SYSTEM/KEY CIRCUIT.....................................3-6
3. SERVO CIRCUIT ...............................................3-7
4. OSD CIRCUIT ....................................................3-9
5. Y/C CIRCUIT ....................................................3-10
6. HI-FI CIRCUIT ..................................................3-14
7. TUNER/IF CIRCUIT .........................................3-17
DETAILS AND WAVEFORMS ON SYSTEM
TEST AND DEBUGGING.......................................3-65
1. SYSTEM 27MHZ CLOCK, RESET SIGNAL ...3-65
2. SDRAM CLOCK ..............................................3-66
3. TRAY OPEN/CLOSE SIGNAL.........................3-66
4. SLED CONTROL RELATED SIGNAL
(NO DISC CONDITION)...................................3-68
5. LENS CONTROL RELATED SIGNAL
(NO DISC CONDITION)...................................3-68
6. LASER POWER CONTROL RELATED
SIGNAL(NO DISC CONDITION) .....................3-69
7. DISC TYPE JUDGEMENT WAVEFORM.........3-69
8. FOCUS ON WAVEFORM ................................3-71
9. SPINDLE CONTROL WAVEFORM
(NO DISC CONDITION)...................................3-72
10. TRACKING CONTROL RELATED
SIGNAL(SYSTEM CHECKING).....................3-73
11. RF WAVEFORM .............................................3-74
12. ZR36882 AUDIO OPTICAL AND COAXIAL
OUTPUT(SPDIF)............................................3-74
13. ZR36882 VIDEO OUTPUT WAVEFORM.......3-75
14. AUDIO OUTPUT FROM AUDIO DAC ...........3-76
BLOCK DIAGRAMS ..........................................3-19
1. POWER(SMPS) BLOCK DIAGRAM ...............3-19
2. TU/IF BLOCK DIAGRAM ................................3-21
3. Y/C BLOCK DIAGRAM ...................................3-23
4. NORMAL AUDIO BLOCK DIAGRAM .............3-25
5. HI-FI BLOCK DIAGRAM .................................3-27
6. SYSTEM BLOCK DIAGRAM...........................3-29
CIRCUIT DIAGRAMS ........................................3-31
1. POWER(SMPS) CIRCUIT DIAGRAM .............3-31
2. TU/IF CIRCUIT DIAGRAM...............................3-33
3. A/V CIRCUIT DIAGRAM..................................3-35
4. HI-FI CIRCUIT DIAGRAM................................3-37
5. JACK CIRCUIT DIAGRAM..............................3-39
6. SYSTEM CIRCUIT DIAGRAM.........................3-41
• WAVEFORMS ....................................................3-43
• CIRCUIT VOLTAGE CHART .............................3-45
BLOCK DIAGRAMS ...........................................3-78
1. SYSTEM BLOCK DIAGRAM...........................3-78
2. SERVO BLOCK DIAGRAM.............................3-79
3. AUDIO & VIDEO IN/OUT
BLOCK DIAGRAM...........................................3-80
PRINTED CIRCUIT DIAGRAMS ....................3-49
1. MAIN P.C.BOARD (TOP SIDE) .......................3-49
2. MAIN P.C.BOARD (BOTTOM SIDE) ..............3-51
3. POWER P.C.BOARD ......................................3-53
4. KEY P.C.BOARD .............................................3-55
CIRCUIT DIAGRAMS .........................................3-81
1. SYSTEM CIRCUIT DIAGRAM.........................3-81
2. SERVO CIRCUIT DIAGRAM ...........................3-83
3. AV/JACK CIRCUIT DIAGRAM ........................3-85
3-1
VCR PART
ELECTRICAL ADJUSTMENT PROCEDURES
1. Servo Adjustment
1) PG Adjustment
• Test Equipment
a) OSCILLOSCOPE
b) NTSC MODEL : NTSC SP TEST TAPE
• Adjustment And Specification
MODE
MEASUREMENT POINT
ADJUSTMENT POINT
SPECIFICATION
PLAY
V.Out
H/SW(TP)
R/C TRK JIG KEY
6.5 ± 0.5H
• Adjustment Procedure
a) Insert the SP Test Tape and play.
Note - Adjust the distance of X, pressing the Tracking(+) or Tracking(-) when the “ATR” is blink after the
SP Test Tape is inserted.
b) Connect the CH1 of the oscilloscope to the H/SW(TP) and CH2 to the Video Out for the VCR.
c) Trigger the mixed Combo Video Signal of CH2 to the CH1 H/SW(TP) and then check the distance (time
difference), which is from the selected A(B) Head point of the H/SW(TP) signal to the starting point of
the vertical synchronized signal, to 6.5H ± 0.5H (412µs, 1H=63µs).
• PG Adjustment Method
a-1) Payback the SP standard tape
b-2) Press the “OK(ENTER)” key on the Remote controller and the “REC” key on the Front Panel the same
time, then it goes in to Tracking initial mode.
c-3) Repeat the above step(No.b-2), then PG adjusts automatically.
d-4) Stop the playback, PG adjustment is finished.
• CONNECTION
V.Out
OSCILLOSCOPE
H/SW
(TP)
CH1 CH2
R/C KEY
H/SW V.out
(TP)
• WAVEFORM
H/SW
6.5H(412µs)
Composite
VIDEO
3-2
ELECTRICAL TROUBLESHOOTING GUIDE
1. Power(SMPS) CIRCUIT
(1) No 5.3VA
No 5.3VA
YES
Is the FR101
Normal?
NO
Replace FR101
(Use the same ICW)
YES
Is BD101 Normal?
NO
Replace BD101
YES
Is R101 Normal?
NO
Replace R101
YES
Is Vcc (9V - 18V) sup- NO
plied to IC101 Pin2?
Is D102 normal?
NO
YES
Are D125 normal?
NO
Is there about 2.5V NO
at IC103 Pin1?
Replace D125
Replace IC103
YES
Is D123 normal?
NO
Replace D123
YES
Is D124 Normal?
NO
Replace D124
YES
Is D121 Normal?
NO
Replace D121
YES
Power Line of Main
PCB is short
3-3
Check or Replace
D102
(2) No 5.0V_D
(3) No 5.0V_T
No 5.0V_D
No 5.0V_T
YES
YES
Is the Vcc(5.3V) sup- NO
plied to Q165 Emittor?
Is the Vcc(5.3V) sup- NO
plied to Q163 Emittor?
Check or Replace
D125
YES
Is the Q162 Base
‘H’?
Check or Replace
D125
YES
NO
YES
Is the Vcc(33V) sup- NO
plied to Q161 Emittor?
Check or Replace
D121
Check or Replace
Q163
(5) No 33V
(4) No 3.3V
No 3.3V
No 33V
YES
YES
Check or Replace
D123
YES
YES
Is there about 3.3V~5V NO
at IC131 pin4?
Check the PWR CTL
“H” signal from µ-com
YES
Check or Replace
Q165
Is there about 3.8V NO
at IC131 pin1?
NO
Is the Q162 Base
‘H’?
Check the PWR CTL
“H” signal from µ-com
Check the PWR CTL
“H” signal from µ-com
Is Q162 Base
‘H’?
YES
YES
Check or Replace
Q161
Check IC131
and Replace
3-4
NO
Check the PWR CTL
“H” signal from µ-com
(6) No Motor_Vcc (To Cap, Drum Motor )
(7) No REG 12V
No REG 12V
No Motor_Vcc
YES
YES
NO
Is the Vcc(14V)
supplied to C134?
Is the Vcc(14V) supplied NO
to Q165 Collector?
Check or Replace
D124
YES
Check or Replace
D124
YES
Is the Vcc(14V) sup- NO
plied to Q165 Base?
Check or Replace
the Cap / Drum
Check the PWR CTL
“H” signal from µ-com
YES
Check or Replace
Q165
(9) No REG 9V
(8) No 9V
No 9V
No REG 9V
YES
YES
Is there about 3.8V
at IC141 pin1?
NO
Is the Vcc(12V) supplied NO
to Q164 Collector?
Check or Replace
D126
YES
YES
Is there about 3.3V~
5V at IC131 pin4?
Check or Replace
D124
NO
Is the Vcc(10V) sup- NO
plied to Q164 Base?
Check the PWR CTL
“H” signal from µ-com
YES
YES
Check or Replace
Q164
Check or Replace
IC141
3-5
Check or Replace
ZD152
2. SYSTEM/KEY CIRCUIT
(1) AUTO STOP
Auto Stop
YES
Does the SW30 waveform
appear at IC501 Pin18?
NO
Check the Drum Motor
signal.
NO
Do T/UP Reel Pulses
appear at the point
between R556 and R536?
YES
YES
Do the T-UP Reel Pulses
appear at IC501 Pin80?
YES
NO
Replace the T/UP Reel
Sensor (RS501).
Replace IC501.
Does 5V appear at RS501?
YES
NO
Check the Q165 Power
Circuit.
(2) The unstable loading of a Cassette tape
The unstable loading of a
Cassette tape
YES
Is 12V applied to PMC01
Pin1?
NO
Refer to “SMPS MOTOR_Vcc
12 Volt Trouble Shooting”.
YES
Does the “H” signal appear
at IC501 Pin60 during
inserting of the CST ?
NO
Is 5V applied to R531 ?
YES
YES
Does the “L” signal appear
at IC501 Pin19 during
inserting of the CST?
Check the CST SW and
the peripheral circuitry.
NO
Refer to SMPS 5.3VA
troubleshooting.
NO
YES
Check IC501 Pins22, 23,
24, 25.
Check the Deck
Mechanism.
Caution : Auto stop can occur because Grease or Oil is dried up
3-6
3. SERVO CIRCUIT
(1) Unstable Video in PB MODE
Unstable Video in
PB Mode.
YES
Does the Noise level of the
screen change
periodically?
YES
Do the CTL pulses appear
at IC501 Pin97?
NO
Is adjusting the height of
the CTL Head accurate?
NO
YES
Readjust the height of the
CTL Head.
Does the CFG waveform
appear at IC501 Pin87?
YES
On tracking do the CTL
pulses move?
NO
Replace IC501.
YES
Does the Video Envelope NO
waveform appear at IC501
Pin9?
YES
Refer to “(2)
No 12VA of Power section”
Replace IC501.
(2) When the Drum Motor
(2) doesn’t run.
Do the Drum PWM Pulses
appear at the IC501
Pin76?
YES
When the Drum Motor
doesn’t run,
Does 12V appear at
PMC01 Pin8?
YES
Check the connector
(PMC01) and the Drum
Motor Ass’y.
NO
YES
Are the foil patterns and
the Components between
IC501 Pin76 and PMC01
Pin12 shorted?
Do the DFG Pulses appear
at PMC01 Pin11?
NO
Replace the DRUM-M or
CAP-M.
NO
YES
Does 2.8V appear at
PMC01 Pin12?
Refer to “When the Y signal
doesn’t appear on the
screen in PB Mode”.
Do the DFG Pulses appear
at IC501 Pin90?
NO
NO
YES
Do the Drum PWM Pulses
appear at IC501 Pin76?
NO
Are the foil patterns and
the Components between
IC501 Pin 90 and PMC01
Pin11 shorted?
Replace IC501.
YES
Are the connecting patterns and the Components
between IC501 Pin76 and PMC01 Pin12 shorted?
3-7
2. SERVO CIRCUIT
(3) When the Capstan Motor doesn’t run,
When the Capstan Motor doesn’t run,
Does 12VA appear at PMC01?
NO
Refer to “SMPS(CAPSTAN/12Volt)
Trouble Shooting”.
YES
Does 2.8V appear at PMC01 Pin 9?
NO
YES
Check the PMC01 and the Capstan
Motor Ass’y.
Does the PWM signal appear at IC501
Pin77?
YES
NO
Are the foil patterns and Components
between IC501 Pin77 and PMC01 Pin9
shorted?
Does the CFG signal appear at
PMC01 Pin1?
YES
NO
Does the CFG signal come into IC501
Pin87?
Check the Capstan Motor Ass’y.
NO
YES
Are the foil patterns and component
between IC501 Pin87 and PMC01 Pin1
shorted?
Does the Capstan PWM signal appear at
IC501 Pin77?
NO
YES
Are the foil patterns and Components
between IC501 Pin77 and PMC01 Pin9
shorted?
Replace IC501.
3-8
2. SERVO CIRCUIT
(4) KEY doesn’t working
KEY doesn’t working.
Is 5V applied to IC501
Pin99?
NO
Refer to “SMPS 5.3VA
Trouble Shooting”.
NO
Replace the defective
switches.
NO
Refer to “SMPS 5.3VA
Trouble Shooting”.
NO
Check or Replace the pheripheral Circurity.(L511,
R518, C596, C595)
YES
Does LED or FLD change
when a function button is
pressed?
4. OSD CIRCUIT
(1) No OSD display.
No OSD or F.OSD display.
Is 5.3V applied to
IC501 Pin53?
YES
Does oscillation occur at
IC501 Pins44, 45?
YES
Replace IC501.
(2) I2C BUS CHECK
The I2C waves don’t
come out.
Does Power appear at the
Pull up impedence
(R569, R507)?
NO
Refer to “SMPS 5.3VA
Trouble Shooting”.
YES
Replace IC501.
3-9
5. Y/C CIRCUIT
(1) No Video in EE Mode,
No Video in EE Mode
Does the Video signal
appear at IC301 Pins28,
30, 32?
NO
Does the Video signal
appear at IC302 Pins1,
3?
NO
Check DVD Video Input
(IC601, Pin150), Tuner
Video Input (TU701 Pin16),
Line Video Input (JK901),
respectively.
NO
Check the System Circuit.
(Refer to ‘SYSTEM I2C BUS
CHECK Trouble Shooting’)
YES
YES
Is there SW5V at
IC302 Pin6?
YES
Replace IC302.
Is REG 5.0V applied to
IC301Pins23, 44, 45, 52,
68, 77?
NO
Check the SW 5V Line.
(Power Circuit)
NO
Is I2C BUS signal applied to
IC301 Pins53, 54, 55?
YES
Does the Video signal
appear at IC301 Pin26?
YES
Does the Video signal
appear at IC501 Pin52?
YES
NO
Check the path of the signal between the IC301 Pin
26 and IC501 Pins50, 52.
NO
Is there 12V on the
terminal of R905?
Replace IC301.
YES
Does the Video signal
appear at the Q924
Emitter?
YES
Replace Q924.
3-10
NO
Check the SW 12V Line.
(Power Circuit)
3. Y/C CIRCUIT
(2) When the Y(Luminance) signal doesn’t appear on the screen in PB Mode,
Is 5V applied to IC301
Pins23, 44, 45, 52, 68, 77?
NO
Check the line of the SW
5V Line.
NO
Refer to ‘SYSTEM Y/C
BUS CHECK Trouble
Shooting’.
NO
Is the V.H.S/W signal
applied to IC301 Pin57?
YES
Is the Y/C Bus siganl
applied to IC301 Pins53,
54, 55?
YES
Does the normal RF signal
appear at IC301 Pin14?
NO
Check the System Circuit.
(IC501 Pin18)
YES
Does the Rectangular
waveform(5V) appear at
IC301 Pin57(V.H.S/W)
YES
YES
Clean the Drum.
Does the Y(Luminance)
signal appear at IC301
Pin20?
NO
Check R328, C322, C323.
YES
Is the Y(Luminance) Video
waveform shown at IC301
Pin22?
NO
Check C324.
YES
Replace IC301.
3-11
NO
Check the V.H.S/W level.
3. Y/C CIRCUIT
(3) When the C(Color) signal doesn’t appear on the screen in PB Mode,
Is SW 5V applied to IC301
Pins23, 44, 45, 52, 68, 77?
NO
Check the line of the REG
5V Line. (Power Circuit)
YES
Does the Color signal
appear at IC301 Pins41,
50?
YES
NO
NO
Is the oscillation frequency
of X301 (3.58MHZ) normal?
Does the Color signal
appear at IC301 Pin48?
YES
Replace IC301.
Replace IC301.
3-12
NO
Replace X301.
Check C342, C341, R333.
3. Y/C CIRCUIT
(4) When the Video signal doesn’t appear on the screen in REC Mode,
REC mode
YES
Is EE mode normal?
YES
Is brightness normal?
NO
Check the EE mode
YES
YES
Is color normal?
Does signal appear at
IC301 Pins41, 50?
Is SW 5V supplied to IC301
Pins23, 44, 45, 68, 77?
Check X301 oscillation
frequency.
NO
Check the SW 5V power.
YES
YES
Check the SW 5V power
YES
NO
YES
Check the power of Pins23,
44, 45, 52, 68, 77.
A
NO
YES
Is the brightness signal sup- NO
plied to IC301 Pins18?
YES
Is Y/C Bus applied to
IC301 Pins53, 54, 55?
NO
Check system part
YES
Do X301 and X-TAL
oscillate?
NO
Check X301.
A
YES
Is V.H SW supplied to
IC301 Pin57?
NO
Check system part
(V.H/SW)
YES
Does the FM signal appear
at IC301 Pins73(SP)/
66(EP)?
NO
Check the drum
YES
Replace IC301.
3-13
*OPTION
Pins72, 73, 74(SP)
Pins65, 66, 67(EP)
6. Hi-Fi CIRCUIT
(1) No Sound(EE Mode)
No Sound.
YES
Check the SIF.IN of IC801 Pins57.
NO
Check the TU701 SIF Pin13.
Check the DVD Audio of IC801
Pins12, 74.
NO
Check the LINE1 Audio of IC801
Pins11, 73.
NO
Check the Rear Jack.
(JK901 Audio in).
Check the LINE2 Audio of IC801
Pins9, 71.
NO
Check the front Jack.
Timer
Check the Vcc of IC801 Pins3, 5, 15,
32, 36, 46, 54.
Check the DVD MODULE.
(PMD02 Pins13, 15).
YES
NO
Check the Power 5V, 5.3VA, REG 9V.
CN701 2,3,11,12
YES
Check the IIC Clock and DATA at
IC801 Pins37, 38.
NO
Check IC501 Pins71, 72.
YES
Check the Audio of IC801 Pins78, 80.
NO
Replace IC801.
YES
Check the Audio of C804, C854.
NO
YES
Check JK901.
3-14
Replace C804, C854.
3. Y/C CIRCUIT
(2) Hi-Fi Playback
PB mode
YES
No Sound.
YES
Check the Vcc of IC801
(Pins3, 5, 15, 32, 36, 46, 54).
YES
NO
NO
Check the Hi-Fi Selection switch.
(IC801 Pin39) and the Tape quality.
YES
Is the RF Envelope at
IC801 Pin23 over 3Vp-p?
YES
NO
Check IC801 Pin37(Data),
Pin38(Clock)
YES
NO
NO
Do Audio Signals appear at
IC801 Pin80(L-CH), 78(R-CH)?
YES
Do Audio Signals appear at
JK901?
NO
Check Power.
Check IC501 Pin19
(A.H/SW)
Check the parts of µ-COM
(IC501 Pins71, 72)
Check the Connection at
P3D01 Pins7, 9.
Check the Jack(JK901)
3-15
YES
Check C801, C851, R801,
R851.
(3) Hi-Fi REC
Hi-Fi REC.
YES
It is impossible to record Hi-Fi Audio
signal.
YES
Check Vcc of IC801.
(Pins3, 5, 15, 32, 36, 46, 54)
NO
Check Power.
YES
Check IC801 Pin37(Data), Pin38(CLOCK).
NO
Check ports of µ-CPM.
(IC501 Pins71, 72)
YES
Do Audio signals appear at IC801 Pin6?
NO
Check Audio input signal of IC801
Pin57(TU.A.), 7, 69(DVD.A.),
11, 73(LINE1.A.), 9, 71(LINE2.A.)
YES
Do Audio signals appear at IC301
Pin76(Normal Audio)?
NO
Check C825, R337, R338, C371, C3A1
YES
Do OSC signals appear at P3D02 pin5
(50Vp-p)
NO
Check REC OSC BLOCK
(Q301, Q302, Q304~Q307)
YES
Is “High” IC501 Pin74 in REC mode.
3-16
7. Tuner/IF CIRCUIT
(1) No Picture on the TV screen
No picture on the TV
screen
YES
Does the Video signal at
the TU701 Pin16.
NO
Is +33V applied to TU701
Pin14?
YES
NO
Check 33V line.
YES
Is +5V applied to TU701
Pin3?
NO
Check 5V line.
YES
Does the Clock signal
appear at TU701 Pin9?
NO
Check the lIC Clock Signal
of µ-COM Pin71.
NO
Check the lIC Data Signal
of µ-COM Pin72.
YES
Does the data signal
appear at TU701 Pin10?
YES
Replace Tuner.
Does the Video signal
appear at IC501 Pin 52.
NO
Check the signal from IC301
Pin29 to IC501 Pin50.
NO
Check the signal from IC501
Pin52 to Q924
YES
Does the Video signal
appear at JK901
YES
Check the signal flow from IC501
Pin52 to JK901 Pin Video out.
3-17
(2) No Sound
No Sound.
YES
Check the Vcc of TU701 Pins3, 14.
NO
Check 5V, 33V Line.
YES
Check the Tuner SiF signal at IC801
Pin57.
NO
Check the Tuner SIF of TU701 Pin13.
YES
Check the Audio of IC801 Pins78, 80.
NO
YES
Check the Signal flow from IC801 Pins78,
80 to JK901 Audio out(L), (R)
3-18
1. Check the Vcc(5.3VA, 9V) of IC801
Pins3, 5, 36, 54.
2. Check the IIC Clock and Data at IC801
Pins37, 38.
BLOCK DIAGRAMS
1. POWER(SMPS) BLOCK DIAGRAM
T101
! TRANS
BD101
C103
+
RECTIFIER &
SMOOTING BLOCK
(D124,C124,C134,
R133,L124,C126)
SNUBBER
BLOCK
(D101,C105
C106,R104)
6 7 8
NOISE FILTER
BLOCK
(C101,L102,
C102)
5
9V REG BLOCK
(Q164,ZD152,C161,
R168,C166)
DRIVE & S/W BLOCK
(IC101, D102, R105,
C104, C108 , C109,
C107,ZD102)
1
3
FUSE
RESISTOR
(FR101)
RECTIFIER &
SMOOTING BLOCK
(D123,C127,C137,
L127)
3.8V REG BLOCK
(IC131,C158,R165)
3.8V
RECTIFIER &
SMOOTING BLOCK
(D121,C126,R136)
33V S/W BLOCK
(Q161,R154,R155
Q173,R174,R177)
33V
!
BR BL
(BK)(WH)
PHOTO COUPLER
(IC102)
Y-CAP
C111
!
ERROR
AMP
(IC103)
3-19
REG9V
8V
RECTIFIER &
SMOOTING BLOCK
(D122,D125,C128,
L128,C138)
!
REG12V
8V REG BLOCK
(D126,IC141,R167,
C165)
2
!
Y-CAP
C110
12V REG BLOCK
(Q166,ZD151,C160,
R166,C159)
MOTOR VCC
14VA
FEED-BACK
BLOCK
(R141,R142,
C143,R143.
R144.R145
R146)
3-20
5.3VA
5V S/W BLOCK
(Q165,C164,R172,
R174)
5.0V
5VT S/W BLOCK
(Q163,C162,D127,
R156,R157)
M5V/5VT
PWR CTL BLOCK
(Q162,C161,R164,
R163)
PWR CTL'H'
V.OUT
NC
TU 30V
SIF
A.OUT
AFT
DATA
CLOCK
ENABLE
NC
RF AGC
V.IN
CONTROL
REG 5V
CH S/W
A.IN
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
999 GND
2. TU/IF BLOCK DIAGRAM
875 MOD A.IN
61
MOD CTL
107 5V
26
VCR 'H'
971 MOD VEDIO
TU.V.OUT 732
71
IIC CLK
72
IIC DATA
33V 158
AFT 100
781 SIF OUT
COMBI NTSC
3-21
3-22
3. Y/C BLOCK DIAGRAM
58
57
55 54 53
AUDIO C-ROT
MUTE RF-SW
HA SW IN
57
55 54 53
X-TAL
3.58MHZ
Y/C ENA
Y/C DATA
Y/C CLOCK
59
ENV
DET
V. H/SW
(REC Mode)
Y/C ENA
Y/C DATA
Y/C CLOCK
(PB Mode)
51 50 49 48 47
SERIAL
DECODER
OUT
VX01
320FH
VCO
CCD
CLAMP
65
CCD
IN
36
IN
EP REC
VCA
66
VCA
R
CLAMP
P
34
3.58M
BPF2
C-LPF
4.21M
BPF
72
P
3.58M
BPF1
ACC
DET
SUB
CONV
4.21M
BPF
YNR
COMB
SUB
CONV
CLAMP
Y
LPF
SP REC
FM
DEM
SUB
LPF
6dB
26
VIDEO
AGC
30
YNR
COMB
DETAIL
ENH
CLAMP
NL
EMPHA
MAIN
EMPHA
Y
LPF
28
V.OUT
DVD
LINE2
V.OUT
26
REC
FM-EQ
MAIN
DE-EM
FM
AGC
R
3.58M
BPF1
ACC
DET
TU/LINE1
FM
MOD
P
DOUBLE
LIM
73
32
B-UP
AMP
22
PB
FM-EQ
22
B
4.7K
SP PB 'A'
MAIN
CONV
ACC
AMP
70
Y/C
MIX
74
C-LPF
69
MAIN
CONV
ACC
AMP
SP PB 'B'
34
CLAMP
BGA
67
37
CLAMP
36
P
CNC
EP PB 'B'
39
38
REC
APC
37
DET
EP PB 'A'
OUT
39
REC
APC
64 ACC
SLD
21
B
20
3-23
3-24
21
IC302
SW
BLOCK
3-25
REAR Jack
2
3
EQ
AMP
3-26
1
LINE AUDIO(L) IN
LINE AUDIO(R) IN
A_IN
RF MOD.
13
71
9
2
57
55
DATA
4
78
A. OUT (R)
80
4
6
(System)
4
NORMAL
AUDIO
OUT
From u-COM
A. OUT (L)
IC801
LA72670M
CLOCK
54
10
78
A. OUT (R)
80
A. OUT (L)
AMP
53
ENA
71
9
2
57
6
NORMAL
AUDIO
OUT
10
76
ALC
2
78
80
DET
ALC
REC
AMP
DET
IC301
LA71206M
OUTPUT
SELECTOR
IC801
LA72670M
10
76
IC301
LA71206M
9
MOD. OUT
A. OUT (R)
A. OUT (L)
(PB Mode)
SIF
TUNER
TU701
5
6
EQ 4
N.A.IN
LA71206M
IC301
LINE AUDIO(L) IN
LINE AUDIO(R) IN
1
13
IC801
LA72670M
(EE Mode)
R/P HEAD
REAR Jack
A_IN
RF_MOD
SIF
TUNER
TU701
4. NORMAL AUDIO BLOCK DIAGRAM
(REC Mode)
5. Hi-Fi BLOCK DIAGRAM
A
DVD AUDIO
REAR JACK
FRONT
57
DVD A.IN 'L'
12
DVD A.IN 'R'
74
AV1 A.IN 'L'
11
AV1 A.IN 'R'
73
AV2 A.IN 'L'
9
AV2 A.IN 'R'
71
DEMO
DULATE
26
27
Hi-Fi PB 'A'
SIF
24
Hi-Fi REC
AUDIO INPUT
BLOCK
Hi-Fi PB 'B'
Hi-Fi/
REC
B
FM MODU
DE MODU
80
78
INPUT
SELECT
A.OUT 'R'
A.OUT
To JACK
OUTPUT
SELECT
3
IC801
LA72670BM
6
4
NORMAL AUDIO
OUT(To AVCP)
NORMAL AUDIO
IN(From AVCP)
3-27
A.OUT 'L'
3-28
MODULATOR
A.OUT
(To Tu)
6. SYSTEM BLOCK DIAGRAM
TO/FROM DECK
TO/FROM AVCP
5.3VA
23 MODE S3
56
CV IN
50
SQPB
H.A.SW
D.V.Sync
V. ENV
V.H.SW30
9 18 13 16 59
60
LD CTL
DPG
CFG
90 87 12
CAP. REV 'H'
24 MODE S2
76 95 94
CTL -
77
I-Limit
25 MODE S1
CTL +
11
GND
MODE S1
MODE S2
MODE S3
MODE S4
CAP. PWM
MS501
DRUM PWM
MODE S/W
COMP IN
17
REC 'H' 74
C.ROT 15
A.MUTE'H' 84
DISPLAY
22 MODE S4
S clk 67
S in 66
S out 65
OSC
DVD DATA OUT
DVD DATA IN
DVD CLK
DVD RESET
DVD ENA
X502
14MHz
38 X in
39 X out
OSC
5V
T-UP END
X501
ES501
32.768KHz
R550
35 Xc in
OSC
IC501
M37760
36 Xc out
A. ENV
A. H.SW
A. MUTE 'H'
REC 'H'
21 T-UP Sensor
ES502
R557
R535
LD501
DECK IR LED
C534
R537
R556
PLL CLK
PLL DATA
VCR 'H'
MODU CTL
80 T-UP Reel
R536
T-UP REEL
66
67
TO/FROM DVD
82
85
8
19
68
TO/FROM AUDIO(Hi-Fi)
74
Hi-Fi ONLY
CV OUT 52
AFT 100
C535
R564
SUP END
RS501
65
CLK 71
DATA 72
20 SUP Sensor
R553
IC5F1
TO/ FROM TU/IF
71
72
26
61
R555
RS502
R538
OSC in 2
OSC out 2
Vss (AMP)
Vss (OSD)
Vss (SYSCON)
Vcc (A/D)
Vcc (OSD)
Vcc
(SERVO)
Vcc
(SYSCON)
R558
45
88
49
40
99
53
98
C582
58 CST IN
14
CST.SW/REC TAP
5.3VA
POWER FAIL 78
44
79 SUP Reel
SUP REEL
37
R/C
CS501
R544
R5C6
GND
34
3
RESET
+
C500
R531
IC504
L511
R598
C595
C596
C552
1
+
3-30
5V
C503
C561
L501
Vcc
1
L512
C592
+
GND
3
R583
R529
IC505
5.3VA
R541
Q501
+
3-29
2
Q503
+
C517
OSC
RC601
Vcc
2
CIRCUIT DIAGRAMS
IMPORTANT SAFETY NOTICE
WHEN SERVICING THIS CHASSIS, UNDER NO CIRCUMSTANCES SHOULD THE ORIGINAL DESIGN BE
MODIFIED OR ALTERED WITHOUT PERMISSION
FROM THE LG ELECTRONICS CORPORATION. ALL
COMPONENTS SHOULD BE REPLACED ONLY WITH
TYPES IDENTICAL TO THOSE IN THE ORIGINAL CIR-
1. POWER(SMPS) CIRCUIT DIAGRAM
NOTES)
Symbol denotes AC ground.
NOTES)
Symbol denotes DC chassis ground.
A
B
NOTE)
NOTE)
NOTE)
NOTE)
C
CUIT. SPECIAL COMPONENTS ARE SHADED ON THE NOTE :
SCHEMATIC FOR EASY IDENTIFICATION.
1. Shaded( ) parts are critical for safety. Replace only
THIS CIRCUIT DIAGRAM MAY OCCASIONALLY DIFwith specified part number.
FER FROM THE ACTUAL CIRCUIT USED. THIS WAY,
2. Voltages are DC-measured with a digital voltmeter
IMPLEMENTATION OF THE LATEST SAFETY AND
during Play mode.
PERFORMANCE IMPROVEMENT CHANGES INTO
THE SET IS NOT DELAYED UNTIL THE NEW SERVICE
LITERATURE IS PRINTED.
Warning
Parts that are shaded are critical
With respect to risk of fire or
electricial shock.
D
E
F
G
H
I
3-31
J
K
L
3-32
M
N
O
P
Q
R
S
T
2. TU/IF CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-33
J
K
L
3-34
M
N
O
P
Q
R
S
T
3. A/V CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-35
J
K
L
3-36
M
N
O
P
Q
R
S
T
4. Hi-Fi CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-37
J
K
L
3-38
M
N
O
P
Q
R
S
T
5. JACK CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-39
J
K
L
3-40
M
N
O
P
Q
R
S
T
6. SYSTEM CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-41
J
K
L
3-42
M
N
O
P
Q
R
S
T
• WAVEFORMS
* IC301 Waveform
* IC501 Waveform
280 Acqs
Tek Stop : 10.0KS/s
299 Acqs
T
Tek Stop : 250KS/s
T
18 Acqs
Tek Stop : 10.0KS/s
Trigger Position: 12%
27 Acqs
Tek Stop : 10.0KS/s
T
T
T
T
T
1
T
1
1
Ch1
IC301 Pin 9
100mV/10msec DIV
VV/EE
(Main De-Emphasis out)
IC301 Pin 12
100mV/10msec DIV
PB
(Main De-Emphais
Peacking)
IC301 Pins 33, 36, 37
100mV/10msec DIV
VV/EE
Clamp Drive IN Pin 33
Y-out(to 1H CCD) Pin 36
Y-out(from 1H CCD) Pin 37
IC301 Pin 15
200mV/10msec DIV
EE
(VIDEO IN)
1.00 V
M5.00ms
Ch1
3.04 V
IC501 Pin 18
REC/PB
1.00 V
M 200µs
Ch1
1.00 V
M 5.00ms
Ch1
1
3.04 V
Ch1
IC501 Pin 13
QUE/REV
(DPG)
(DFG)
IC301 29 Pin
500mV/10msecDIV
VV/EE
(VIDEO OUT)
IC301 Pin 43
200mV/20msec DIV
PB
(C.OUT)
IC301 Pins 46, 57
200mV/20msec DIV
VV/EE
from 1H CCD Pin 46
to 1H CCD Pin 57
IC301 Pin 67
100mV/0.2msec DIV
PB/REC
(3.58MHz X-TAL IN)
IC301 Pin 77
100mV/5msec DIV
PB
(PB RF out)
IC301 Pin 86
500mV/2msec DIV
SP REC
(REC RF)
1
3.04 V
Trigger Level: 340mv
2 Acqs
T
1
1
Ch1
Ch1
1.00 V
IC501 Pin 94
REC
IC301 Pin 90
500mV/2msec DIV
EP REC
(REC RF)
3-43
Ch1
T
T
IC301 31 Pin
1.0V/20msec DIV
VV/EE
(C-SYNC OUT)
M5.00ms
Tek Stop : 5.00KS/s
T
T
IC301 53 Pin
100mV/0.2msec DIV
REC/PB
(2fsc)
1.00 V
IC501 Pin 95
REC
120 Acqs
Tek Stop : 50.0KS/s
T
Ch1
3.04 V
IC501 Pin 13
QUE/REV
35 Acqs
Tek Stop : 10.0KS/s
Ch1
3-44
M5.00ms
Ch1
3.04 V
Ch1
1.00 V
IC501 Pin 87
REC/PB
M1.00ms
Ch1
500mV
M 10.00ms Ch1
3.04 V
IC501 Pin 90
REC/PB
(DPG/DFG)
IC501 Pin 97
PB
(CTL OUT)
340V
• CIRCUIT VOLTAGE CHART
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
IC202
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
80
4. 13
4. 19
54
55
PLAY
MODE
PIN NO.
STOP
PLAY
0
0
8
0.17
0.09
2.06
2.005
9
0.17
0.16
0.01
STOP
9
0
0
13
2.16
0.9
13
3.2
3.22
19
0
0
24
2.27
2.24
1
0.02
1.28
10
2.4
2.47
14
3.2
3.25
14
0
0
20
5.23
5.23
25
0
0
2
0
0
11
2.94
0
15
0
0.9
15
0
0
26
2.27
2.25
1
0.06
0.06
56
0
0
10
0.01
3
8
0.56
12
2.94
0
16
3.15
0.81
16
3.2
3.22
1
4.97
4.95
27
2.27
2.25
2
0.05
0.06
57
2.15
2.11
11
0.03
3.4
4
0.03
0.62
13
2.121
0
17
2.7
0.82
17
3.2
3.22
2
2.31
2.26
28
0
0
3
0.06
0.06
58
2.02
1.9
12
0.24
0.01
5
0
1.73
14
3.18
3.2
18
3
0.83
18
0.01
0.01
3
0
4.95
29
3.2
3.25
4
5.08
5.1
59
4.95
0
13
0.03
0.03
6
2.7
2.23
15
3.18
3.21
19
2.3
0.82
19
0.01
0.01
4
1.32
1.43
30
0
0
5
2.17
2.1
60
4.1
5
14
4.8
0
7
2.93
0
16
1.58
1.58
20
0.25
0.83
20
0.03
0.01
5
0
0.01
31
2.5
2.53
6
2.57
2.56
61
2.37
4.15
15
0.01
2.57
8
2.7
2.23
21
0.44
0.8
21
3.18
3.22
6
1.08
1.45
32
5.05
5
7
2.83
2.83
62
2.18
1.37
16
0.3
0.01
9
2.93
3.22
1
5.54
5.52
22
0
0.8
22
0.01
0.01
7
0
0
33
2.66
2.64
8
1.9
2
63
1.97
2.2
17
0.33
0.01
10
2.72
2.11
2
5.54
5.52
23
0
0.8
23
3.2
3.22
8
2.4
2.3
34
0
2.64
9
1.87
1.3
64
2.22
2.61
18
5.14
2.57
11
2.92
1.74
3
5.5
5.52
24
0.06
0.8
24
3.18
3.22
9
0.05
0.05
35
0
0
10
2.36
1.42
65
1.93
2.24
19
5.14
2.57
12
1.64
2.24
4
0
0
25
0.25
0.84
25
3.2
3.22
10
2.31
2.25
36
5.1
5
11
2.08
1.88
66
2.16
2.31
20
4.32
0.14
13
8.04
1.74
5
5.5
5.3
26
0.25
0.83
26
3.2
3.22
11
4.2
4.2
37
4.74
4.75
12
1.65
0.58
67
2.45
2.18
21
4.28
0.02
14
8.04
1.75
6
5.54
5.52
27
3.2
3.22
27
0
0
12
2.3
2.265
38
4.75
4.74
13
0
0
68
2.03
2.45
22
0
5.1
15
2.95
3.2
7
5.54
5.52
28
0
0
28
0
3.2
13
4.97
4.9
39
5.13
5.12
14
1.38
2.31
69
1.8
2
23
0
5.2
16
0.01
0
8
12.1
12.1
29
0.36
1
29
0.8
0.93
14
2.34
2.26
40
0
0.97
15
2.8
2.8
70
1.9
1.8
24
5.2
5.2
17
0
3.2
30
0.34
1
30
0.54
0.95
15
0
0
41
2.52
2.55
16
0.18
1.9
71
0.23
0.76
25
5.21
0.01
18
2.79
1.74
1
2.45
2.15
31
0
1.05
31
0.53
0.8
16
0
2.3
42
2.52
2.53
17
0
2.8
72
4.92
4.95
26
5.14
5.1
19
0.46
0.01
2
4.9
4.9
32
0.32
1.03
32
0.54
0.78
17
0
0
43
2.53
2.54
18
0
1.96
73
4.75
5
27
0
0.1
20
2.77
2.13
3
4.93
4.92
33
0.32
1
33
0.56
0.74
18
2.38
2.3
44
2.53
2.58
19
2.78
2.8
74
4.75
0
28
5.14
5.1
21
2.94
2.13
4
4.88
4.88
34
0.32
1
34
0.6
0.76
19
0
0
45
0.49
0.49
20
0
4.1
75
2.63
2.65
29
0
0.01
22
0.46
0.01
5
5
4.5
35
0.32
1
35
0.77
0.8
20
2.34
2.3
46
5.09
5.07
21
2.8
2.8
76
2.2
2.12
30
0.01
0.01
23
0
0
6
0.7
2.8
36
0
0
36
0.8
0.9
21
0
1.8
47
2.49
2.51
22
5
5
77
2.83
2.84
31
0.01
0.01
24
0
0
7
0.71
2.57
37
3.18
3.2
37
3.16
3.2
22
0
0
48
0
2
23
2.3
2.32
78
0.03
2.15
32
0.01
0.01
25
0.46
0
8
0.72
2.5
38
1.77
1.8
38
0.82
3.2
23
1.56
1.66
49
4.4
0
24
0.33
0.44
79
0
0
33
0.01
0
26
0
3.22
9
0.72
2.7
39
0.33
1.04
39
0.77
0.8
24
0.03
0
50
0
0
25
2.11
2.13
80
2.83
2.54
34
5.17
5
27
0
0
10
1.24
2.3
40
0
0
40
0.76
0.76
25
0.03
0.03
51
1.74
1.72
26
0
2.77
81
0.04
0.04
35
1.46
0
28
0.46
2.58
11
1.74
2.77
41
0
0
41
0.7
0.8
26
2.38
2.31
52
1.23
1.24
27
0.32
0.35
82
0.01
0.01
36
0
1.35
29
0
2.75
12
2.4
0.94
42
0
0
42
0.77
0.83
27
0.03
0.03
53
3.88
3.89
28
0.03
0.03
83
0.13
0.02
37
5.17
0
30
2.7
1.27
13
0.9
1
43
0
3.22
43
0.74
0.82
28
4.96
4.94
54
9.27
9.2
29
1.68
2.15
84
5
5
38
2.22
0
31
0
0
14
1.37
1.93
44
0
0
44
0.73
0.83
55
3.88
3.9
30
2.22
2.85
85
2.28
1.37
39
2.3
2.29
32
0
2.75
15
0.55
2.44
45
0
0
45
0.75
0.8
1
0
0
56
2.16
2.18
31
0.14
0.22
86
2.28
1.4
40
0
0
33
0
2.77
16
2.08
2.27
46
0
0
46
0
0
2
2.17
2.53
57
0
4.6
32
2.25
2.2
87
2.28
1.35
41
0.25
0.57
34
0.02
2.74
17
1.85
2.21
47
0
0
47
3.16
3.2
3
9.27
9.2
58
4.58
2.48
33
2.11
2.12
88
0
0
42
0.28
0.57
35
3.2
1.74
18
5
4.5
48
0.32
0
48
3.2
3.2
4
2.48
2.5
59
2.51
3.9
34
1.85
1.86
89
2.27
1
43
0
0
36
0
0.28
19
0
0
49
3.23
3.22
5
5.23
5.23
60
3.88
3.2
35
3.03
3
90
2.27
1
44
2.4
2.37
2.37
IC203
IC402
IC5F1
IC604
IC609
IC801
IC301
20
2.2
2
50
0.31
3.22
1
0
0
6
1.98
1.98
61
3.2
3.78
36
2.38
2.4
91
2.27
1
45
2
1
2.4
4.8
21
0
2.16
51
0.3
1
2
1.68
0.95
7
0
0
62
3.83
3.86
37
3.03
3
92
5.05
5
46
0
0
2
2.72
4.84
22
2
2.2
52
0
0
3
0
0
8
0.01
0.73
63
3.85
2.5
38
2.14
2.17
93
0.45
0.44
47
1.44
1.36
3
2.7
4.84
23
1.84
2.34
53
0.3
1
4
1.7
1.26
9
0
0
64
2.5
3.9
39
1.48
1.52
94
0.01
2.5
48
0
0
4
0
0
24
0
0
54
0
0
5
4.28
3.44
10
0
0
65
3.9
4.1
40
2.1
2.11
95
2.52
2.5
49
0
0
5
0
0.03
6
1.7
1.35
11
0
0
66
4.11
3.85
41
2.7
2.76
96
0
2.5
50
0.15
1.64
6
1.04
1
1
3.2
3.25
1
3.2
3.22
7
5.2
5.2
12
2.5
2.5
67
3.4
3.96
42
1.97
2
97
0
0
51
0.2
0.7
7
0.12
0.4
2
0
1
2
3.2
3.2
8
0
3.2
13
1.97
1.96
68
3.95
0
43
2.1
2
98
2.36
2.2
52
1.37
1.63
7.8
8
3
3.2
3.25
3
0.01
0.01
9
2.3
0.1
14
2.49
2.51
69
0
0
44
0
0
99
0
0
53
5.04
5.1
4
1.6
1
4
3.2
3.22
10
0
0
15
2.52
5
70
0
0
45
3.26
3.2
100
2.57
2.57
54
0
2.6
0
1
5
3.18
3.22
11
0
0
16
0
2.5
71
0
3.9
46
3.26
3.23
55
1.4
1.96
8
IC401
IC602
IC603
IC501
1.59
1.6
5
2
0
1.6
6
0
0
6
0
0.01
12
0.09
5.23
17
0.48
0
72
3.9
0
47
5.05
5.1
1
0.97
0.08
56
0
1.77
3
1.58
1.6
7
1.8
1
7
3.18
3.22
13
3.2
3.2
18
0.49
0.48
73
0
2.5
48
4.92
4.95
2
5.2
5.2
57
0
01.56
1
4
0
0
8
0
1
8
3.17
3.22
14
0
0
19
2.54
2.53
74
2.49
3.9
49
3.56
3.53
3
5.2
5.2
58
0
0
5
3.12
3.17
9
3.2
3.25
9
3.2
3.22
15
2.6
2
20
2.54
2.54
75
3.89
3.2
50
5.05
5.08
4
0
0
59
0.01
4.1
6
4.03
4.9
10
2.14
1
10
0
0
16
0
0
21
2.53
2.53
76
3.2
0
51
2.25
2.23
5
0
1
60
2.6
2.6
7
2.5
2.5
11
0.53
1
11
3.2
3.22
17
1.31
1.11
22
0
2.53
77
0.01
4.2
52
5.05
5.1
6
5.1
5
61
4.15
4.13
8
2.45
2.5
12
0
0
12
4.08
4.1
18
0
0
23
0
0.17
78
4.14
0
53
2.57
2.6
7
0.2
0.74
62
0.01
0
3-45
3-46
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
MODE
PIN NO.
STOP
PLAY
63
0.05
0.05
17
64
0.05
0.05
18
1.56
0
0
1.35
72
0
0.15
127
2.26
3.22
182
2.23
3.2
73
0.53
0.04
128
3.18
3.22
183
2.2
65
2.25
2.3
19
0
3.2
0
74
2.4
2.41
129
3.19
3.22
184
0
66
2.4
0.06
20
3.2
0
0
75
2.4
2.46
130
3.18
3.22
185
2.92
67
5.2
5.2
0
21
0
0
76
3.2
3.06
131
0
3.21
186
0
3.2
68
4.94
69
4.9
4.94
22
0.05
0
77
3.22
3.13
132
3.18
3.21
187
2.3
2.46
4.88
23
3.2
0.05
78
3.22
3.13
133
3.18
3.2
188
1.7
70
2.48
4.9
4.92
24
0.8
0.84
79
0
0.01
134
3.18
3.22
189
0
2.52
71
4.77
4.94
25
0.05
0.66
80
0
0.01
135
3.16
0
190
0
0
72
4.74
5.12
26
0.49
0.58
81
3.22
3.22
136
3.19
3.22
191
2.22
2.4
73
0.01
0.01
27
0.63
0
82
1.78
1.83
137
3.19
0
192
0
2.38
74
0.01
0.01
28
0
0.03
83
0
0
138
0
3.22
193
0
2.39
75
0.8
0.01
29
1
1.3
84
1.3
0.63
139
3.2
3.22
194
0
2.15
76
0.82
2.66
30
3.19
3.22
85
1.8
0.81
140
3.2
3.22
195
0
3.23
77
0.01
2.66
31
0
0
86
1.21
0.7
141
0.45
0
196
2.22
2.36
78
4.8
4.8
32
0.5
0
87
1.3
0.7
142
0.43
3.22
197
3.2
2.37
79
4.87
4.44
33
0.7
0.7
88
1.4
1.2
143
0.47
3.21
198
2.24
1.67
80
4.85
4.21
34
0.55
0.55
89
2.3
0.7
144
0.42
3.21
199
2.28
0
81
0
2.58
35
0
0.02
90
2
0.7
145
0.48
3.21
200
0.01
2.4
82
4.11
4.17
36
1.28
1.3
91
1.4
0.7
146
1.03
3.21
201
0
2.4
83
4.86
4.86
37
1.68
1.66
92
0.82
0.69
147
1.03
0
202
0
0
84
0
0.01
38
0.05
0
93
0.81
0.68
148
1.76
3.23
203
0.01
0
85
4.26
4.2
39
0.4
2.5
94
1.71
1.7
149
0
0
204
0.24
0
86
0.13
0
40
0.6
2.44
95
1.75
1.8
150
0
0
205
3.22
3.25
87
2.6
2.36
41
2.45
3.21
96
0
0
151
1.03
0.98
206
2.65
3.25
88
0
0
42
2.43
2.42
97
0
0.7
152
1.04
0.99
207
3.22
2.37
89
0.12
0.3
43
2.46
2.46
98
0.92
0.7
153
1.05
0.99
208
2.1
0.01
90
0
1.37
44
0.8
0.01
99
0.93
0.66
154
1
0.98
91
2.59
2.5
45
0
0.01
100
0.93
0.67
155
0.94
0.98
92
2.6
2.5
46
0
0.01
101
0.93
0.66
156
0.92
0.98
93
0
0.03
47
1.77
0
102
2.52
0.65
157
1.04
0.98
94
2.54
2.52
48
2.9
1.67
103
2.57
2.38
158
1.05
1
95
2.54
2.52
49
0
0
104
2.57
2.5
159
3.24
3.22
96
2.58
2.54
50
0
0
105
2.26
1.68
160
0
0
97
0.28
2.54
51
0
1.6
106
1.65
3.2
161
3.19
0.81
98
5.2
5.1
52
0
1.6
107
3.18
0.03
162
0
0.81
99
5.2
5.2
53
0
0
108
0
0
163
3.2
0.81
100
0.16
0.16
54
0
0
109
0
0
164
3.19
0.81
55
1.2
0.09
110
3.2
3.2
165
0.77
0.01
0.01
IC601
1
1.4
0.06
56
1.28
0
111
0.47
0.9
166
0
2
0
1.6
57
1.56
0
112
3.2
3.2
167
3.19
3.2
3
2.45
2.52
58
1
1.07
113
3.2
3.2
168
0.77
0.01
4
3.1
3.21
59
1
1
114
0.02
0.02
169
3.17
3.2
5
0
0
60
1.11
0
115
0.03
0.03
170
3.17
3.2
6
0
3.2
61
1.11
0
116
0.02
0.02
171
1.68
1.66
7
3.15
3.2
62
1.11
0
117
3.19
3.21
172
0
0
8
0
3.2
63
1.11
0
118
1.79
1.93
173
0
0.01
3.2
9
3.15
3.2
64
0.03
1.7
119
1.69
1.66
174
0
10
3.15
3.2
65
0
0
120
1.56
1.66
175
0
3.2
11
3.15
3.2
66
1
0.64
121
0
0
176
0
0.01
12
3.1
3.17
67
0.96
0.64
122
1.79
1.79
177
0
3.2
13
3.1
3.21
68
0.93
0.64
123
0
0
178
0
3.2
14
1.6
1.68
69
0.23
0.62
124
4.1
4.1
179
0
3.2
15
0
0
70
1
3.14
125
3.08
3.24
180
0
3.2
16
0
0.65
71
0
0.01
126
2.27
3.23
181
0
3.2
3-47
3-48
PRINTED CIRCUIT DIAGRAMS
1. MAIN P.C.BOARD (TOP SIDE)
3-49
3-50
2. MAIN P.C.BOARD (BOTTOM SIDE)
3-51
3-52
3. POWER P.C.BOARD
LOCATION GUIDE
NOTES)
NOTES)
NOTES)
NOTES)
3-53
Warning
Parts that are shaded are critical
With respect to risk of fire or
electricial shock.
3-54
4. KEY P.C.BOARD
3-55
3-56
DVD PART
ELECTRICAL TROUBLESHOOTING GUIDE
1. POWER CHECK FLOW
A.
B.
No 5V
Is 3.4VA section working?
No 3.4VA.
NO
NO
YES
YES
Is 5.6V present at collector
of Q126?
No 3.4VA
NO
Is 3.4V present at emitter
of Q121?
YES
YES
Replace Q126.
Is 3.4VA section working?
Check FR101
Replace Q121.
YES
Is there a DC voltage at
Cathode of D105 or D107?
NO
Replace IC101.
3-57
NO
Check D105/D106/D107/
D108 and replace.
2. SYSTEM OPERATION FLOW
Power On
1. 186 CPU initializes SERVO,DSP & RISC registers
2. Write RISC code to SDRAM
3. Reset RISC
Show LOGO
YES
Tray Closed ?
NO
Tray Close to Closed position
SLED at Inner Side ?
YES
NO
SLED Moves to Inner Position
1. Judge whether have disc and disc type
2. Jump to related disc reading procedure
Recieve OPEN/CLOSE Key?
YES
NO
1. Execute Pressed Key & IR Key
2. System operation Routine Loop
1. Stop Playback & Open Tray
2. Display tray open message & LOGO
YES
Receive CLOSE Key?
YES
3-58
3. Test & debug flow
TEST
Check the AC Voltage
Power PCBA(110V or 220V)
NO
Replace power PCBA or AC transformer.
YES
Switch on the Power PCBA
YES
Is the DC Voltage outputs OK?
(5V, 3.3V, 12V, 5.6V MOTOR)
NO
Repair or Replace Power PCBA
YES
Make sure the main PCBA don't short on
VCCs and switch it on.
YES
Is 3.3V outputs normal on main PCBA?
NO
Check the regulators or related diodes.
YES
Is 1.8V Voltage normal for Zoran IC
NO
1. Check Q203.
3. Check IC102
2. Check D201.
YES
Connect to PC RS232 Cable and update
the FLASH memory code.
YES
Update FLASH successfully?
YES
NO
1. Check 27MHz system clock.
2. Check system reset circuit.
3. Check FLASH R/W enable signal
PRD,RWR.
4. Check RS232 SIGNALS.
5. Check FLASH Memory related circuit.
A
3-59
A
RESET or Power On.
Show LOGO?
NO
YES
Flash Memory operates
properly?
NO
Check connection lines between
FLASH & ZR336888 and the FLASH
access time whether is suitable or not.
NO
Check connection lines
between SDRAM & ZR36882
and the SDRAM is damaged.
NO
Check the related circuit of
ZR36882
NO
Check the filtering and amp
circuit of TV signal.
YES
SDRAM works properly?
YES
ZR36882 VIDEO outputs
properly?
YES
Have TV signal output?
YES
Check AV cable connection
to TV set.
Does Tray move inside when
it is not at closed position?
YES
NO
Normal OUTSW & INSW
signals?
NO
Check the load OPEN &
CLOSE switch
NO
Check the Tray control IO
pins on ZR36882 &
AM5869S
NO
Check the Tray control
amplifying circuit on Motor
driver.
YES
Normal OPEN & CLOSE
signal?
YES
Normal LOAD+ & LOAD signal?
YES
B
Check the cable connection
between main PCBA and
loader.
3-60
B
Does the SLED move to
NO
inner side when it is at outter
position?
YES
Motor Driver MUTE Pin is
High?
NO
Check the connection line of
MUTE signal.
NO
Check the related circuit of
FMSO.
NO
Check the amp circuit on
motor driver.
YES
Is SLED_S DC Level higher
than 1.65V?
YES
SLED+ and SLED- output
properly?
YES
Do not put in disc and tray
close.
Optical Lens has movements
for searching Focus?
YES
Check the cable connection
with MECHA.
NO
Proper FOCUS_S outputs to
motor driver?
Check FOCUS_S connection
On ZR36882 and motor dirver.
NO
Check the amp circuit on
motor dirver.
YES
Proper FACT+ &
FACT- outputs?
YES
C
NO
Check cable connect on with
pick-up head.
3-61
C
Laser turns on when
reading disc?
NO
YES
LD_DVD or LD_CD
output properly?
NO
Check the laser power circuit
on ZR36882 and connecting
to power transistor.
NO
Check the related circuit on
laser power transistor
NO
Check the related circuit
on ZR36882 RFL signal.
NO
Check SPINDLE_S related
circuit on ZR36882.
NO
Check the spindle control
amp circuit of motor driver.
YES
Collector voltage of power
transistor is OK?
YES
Check cable connection
between transistor ouput
and pick-up head.
Put disc in?
NO
Laser off
YES
Disc ID is correct?
NO
YES
Proper RF signal on
ZR36882?
YES
Check LD_DVD & LD_CD
signal
Does spindle rotate?
YES
NO
Proper SPINDLE_S signal
on ZR36882
YES
SP+ & SP- output properly?
YES
D
Check the cable connection
between spindle and main
PCBA.
3-62
D
Focus ON OK?
NO
YES
Proper signals on A,B,C,D
of ZR36882
NO
Check connections between
ZR36882 and pick-up head.
NO
Check the FOCUS_S
connection on ZR36882
and motor driver.
NO
Check the related
circuit on ZR36882
NO
Check the TRACK_S
connection on ZR36882
and motor dirver.
NO
Check the tracking control
amp circuit on motor driver.
YES
Check FE signal on
ZR36882
YES
Check FOCUS_S signal
on ZR36882
Track On OK?
NO
YES
Normal TE Signal on
ZR36882?
YES
Properly TRACK_S signal
on ZR36882?
YES
TACT+ & TACT- output
properly?
YES
Check cable connection on
pick-up head.
Disc is play ?
NO
Check RF signal waveform.
YES
E
3-63
E
Normal Audio output
when disc playback?
NO
YES
Audio DAC received
correct data stream?
NO
Check connection between
ZR36882 & Audio DAC.
NO
Check the related circuit of
Audio DAC.
NO
Check communication lines
on ZR36882
YES
Normal Audio DAC out?
YES
Check Audio filter, amplify,
mute circuit.
Normal IR.VFD & Front
panel key functions?
YES
TEST END
NO
Communications between
IR.VFD Front panel key &
ZR36882 is normally?
YES
Check the cable connection
on Front panel.
3-64
DETAILS AND WAVEFORMS ON SYSTEM TEST AND DEBUGGING
1. SYSTEM 27MHz CLOCK, RESET SIGNAL
1) ZR36882 main clock is at 27MH(X601)
3.1V,27MHz
FIG 1-1
2) ZR3682 reset is low active
3.3VA
PWR_CTL
RESET
Reset Time
FIG 1-2
3-65
2. SDRAM CLOCK
1) SDRAM clock is at 143MHz
CLK=143MHz,Vp-p=3.3V
IC603 PIN38
FIG 2-1
3. TRAY OPEN/CLOSE SIGNAL
1) Tray open/close waveform
OPEN
CLOSE
LM-
LM+
OPEN
CLOSE
FIG 3-1
3-66
2) Tray open waveform
OPEN
CLOSE
LM-
LM+
FIG 3-2
3) Tray close waveform
OPEN
CLOSE
LM-
LM+
FIG 3-3
3-67
4. SLED CONTROL RELATED SIGNAL(NO DISC CONDITION)
SLED_S
DRVSB
SLED+
SLED-
FIG 4-1
5. LENS CONTROL RELATED SIGNAL(NO DISC CONDITION)
FOCUS_S
FOCUS+
FOCUS-
FIG 5-1
3-68
6. LASER POWER CONTROL RELATED SIGNAL(NO DISC CONDITION)
DCLK = 128MHz, Vp-p=2.2, Vmax=2.7V
VR_CD
DVD_LD
CD_LD
FIG 6-1
7. DISC TYPE JUDGEMENT WAVEFORM
FACT+
FE
SBAD
FIG 7-1(DVD)
3-69
FACT+
FE
SBAD
FIG 7-2 (DVD)
FACT+
FE
SBAD
FIG 7-3 (CD)
3-70
FACT+
FE
SBAD
FIG 7-4 (CD)
8. FOCUS ON WAVEFORM
FE
FOSO
FACT+
FACT-
FIG 8-1 (DVD)
3-71
FE
FOCUS
FACT+
FACT-
FIG 8-2 (CD)
9. SPINDLE CONTROL WAVEFORM(NO DISC CONDITION)
SPINDLE_S
SP+
SP-
(DVD) FIG 9-1
3-72
10. TRACKING CONTROL RELATED SIGNAL(System checking)
TE
TRACK_S
TACT+
TACT-
FIG 10-1 (DVD)
TE
TRACK_S
TACT+
TACT-
FIG 10-2 (CD)
3-73
11. RF WAVEFORM
RFO
FIG 11-1
12. ZR36882 AUDIO OPTICAL AND COAXIAL OUTPUT(SPDIF)
SPDIF
FIG 12-1
3-74
13. ZR36882 VIDEO OUTPUT WAVEFORM
1) Full colorbar signal(CVBS)
JK702 pin6
FIG 13-1
2) Y
JK702 pin7
FIG 13-2
3-75
3) C
JK702 PIN8
FIG 13-3
14. AUDIO OUTPUT FROM AUDIO DAC
1) AUDIO L/R
1KHz 0DB
JK702 PIN4,5
FIG 14-1
3-76
2) Audio Related Signal
AOUT0
ABCK
ALRCLK
FIG 14-2
3-77
M
LOAD+/-
MOT_SPDL +/-
3-78
POWER
BOARD
FACT+/-,TACTT +/-
AC 90V~240V
50HZ/60Hz
DECK MECHANISM
M5V/5VT
5.0V
5.3VA
33V
PWR_CTL_H
8V
3.3V
REG_9V
REG_12V
MOTOR_VCC
DRVSB,TRACK_S,FOCUS_S,SLED_S SPINDLE_S
OPEN, CLOSE
OUTSW , INSW
HOMESW
PICKSEL
DVD_LD,CD_LD, V C
DVD_ENA*
DVD_CLK
DVD_DATA*
IC801
TDA9605H
HIFI
5V/REG12V
27MHz
X-TAL
IC601
ZR36882ELCG
DSP/MPEG/RF
RAMADD[00:10]
RAMBA
PCLK
RSMCS0
RAMRAS#
RAMCASRAMWE-
MEMDA[0:14]
IC501
MN101DF10G
VCR MICOM
VCR_DATA
DVD_RESET
5V
CN602
HYPER_TERMINAL
DVD:RF,A,B,C,D
CD:RF,A,B,C,D,E,F
5V
CN601
DOWNLOAD
MEMAD[00:
18]
FLASHCSMEMRDMEMWR-
IC603
HY57V641620E
SDRAM
RAMDQM
M5V
PICK
UP
IC604
MX26LV160T
FLASH ROM
DV33
RAMDAT[00:15]
IC201
AM5869S
MOTOR
DRIVER
M
SLED+,SLED--
M
SLED
LOADING
(FEEDING)
MOTOR
MOTOR
SPINDLE
MOTOR
DISC
DV33
AMCLK
AB CLK
ALRCLK
MUTE_C
R
L
ASPDIF
A_R +/-
A_L +/-
AL PCLK , AB CLK
AMCLK , AOUTO
IC607
CS5331A
RFV33/DV33/1.8V
AIN
MUTE
MUTE
CIRCUIT
MD
MIC_IN
KARAOKE
Y(G)
Pb(B)
Pr(R)
Y/C
COAX
OPTICAL
R
L
IC605
KS24C021CS
EEPROM
5V
+12V
IC402
NJM4580
OP-AMP
MC
MIIC_DET
KARAOKE OPTION
BLOCK DIAGRAMS
1. SYSTEM BLOCK DIAGRAM
MD
DISC
3-79
LOAD +/-
SLED +/-
MOT_SPDL +/-
FACT +/-, TACT +/-
IC201
AM5869S
Motor Dr iver
HOMESW,INSW,OUTSW
DVD: A,B,C,D, RF
CD: A,B,C,D, E, F,RF
PICKSEL
CD_MD, DVD_MD
DVD_LD, CD_LD , VR_CD , VR_DVD
OPEN ,CLOSE
FOCUS_S, TRACK_S,
SLED_S, SPINDLE_S,
SPDL_SENS +/-
DRVSB
IC601
ZR36882ELCG
MPEG / DSP/RF
27MHz
X-TAL
X601
RXD, TXD
SCL, SDA
FLASHCSMEMRDMEMWR-
MEMAD[0:19]
MEMDA[0:15]
CN601
DOWNLOAD
EEPROM
FLASH
ROM
2. SERVO BLOCK DIAGRAM
IC301
AVCP
IC601
MPEG
ZR36882
3-80
EU1_V_OUT
C
Y
Y / Green
Pb / Blue
Pr / Red
ASPDIF
SCL
SDA
V_IN
A_R+/-
A_L+/-
MUTE_C
S/W
IC903
BH78968FS
IC605
EEPROM
C
Y
Y / Green
Pb / Blue
Pr / Red
IC402
OP-AMP
IC801
HI-FI
DVD_A_L
DVD_A_R
DVD_A_L
DVD_A_R
A.OUT_R
A.OUT_R
V_OUT_1
A.OUT_L
V_OUT_2
A.OUT_L
A.IN_L
A.IN_R
A.IN_R
A.OUT_
R
Pr
DVD_A_R
A.IN_L
A.IN_
R6
V.IN
C
Y
A.IN_L
A.OUT_L
Pb
DVD_A_L
OPTICAL
V.IN
V.OUT
Y
COAXIAL
3. AUDIO & VIDEO IN/OUT BLOCK DIAGRAM
CIRCUIT DIAGRAMS
1. SYSTEM CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-81
J
K
L
3-82
M
N
O
P
Q
R
S
T
2. SERVO CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-83
J
K
L
3-84
M
N
O
P
Q
R
S
T
3. AV/JACK CIRCUIT DIAGRAM
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
3-85
J
K
L
3-86
M
N
O
P
Q
R
S
T
SECTION 4 MECHANISM OF VCR PART(D-37)
CONTENTS
DECK
MECHANISM PARTS LOCATIONS
• Top View......................................................4-1
• Bottom View ...............................................4-1
DISASSEMBLY AND
ASSEMBLY OF DECK MECHANISM
01.Disassembly of Drum assembly ................4-2
02.Disassembly of Plate top disassembly..... 4-4
03.Holder Assembly CST ...............................4-4
04.Disassembly of Gear Assembly
Rack F/L....................................................4-4
05.Opener Door .............................................4-4
06.Arm Assembly F/L .....................................4-4
07.Lever Assembly S/W .................................4-4
08.Motor Assembly L/D ..................................4-5
09.Gear Wheel ...............................................4-5
10.Arm Assembly Cleaner..............................4-5
11. Head F/E ...................................................4-5
12.Base Assembly A/C Head .........................4-5
13.Brake Assembly T .....................................4-6
14.Arm Assembly Tension..............................4-6
15.Reel S / Reel T..........................................4-6
16.Base Assembly P4 ....................................4-7
17.Opener Lid ................................................4-7
18.Arm Assembly Pinch .................................4-7
19.Arm T/up ...................................................4-7
20.Supporter, Capstan ...................................4-8
21.Belt Capstan/Motor Capstan .....................4-8
22.Lever F/R ..................................................4-8
23.Clutch Assembly D37 ................................4-8
24.Gear Drive/Gear Cam ...............................4-9
25.Gear Sector...............................................4-9
26.Brake Assembly Capstan ..........................4-9
27.Plate Slider................................................4-9
28.Lever Tension ............................................4-9
29.Lever Spring..............................................4-9
30. Lever Brake..............................................4-9
31.Gear Assembly P2/Gear Assembly P3 ...4-10
32.Base Assembly P2/Base Assembly P3 ...4-10
33.Base Loading ..........................................4-10
34.Base Tension ...........................................4-11
35.Arm Assembly Idler Jog ..........................4-11
DECK MECHANISM ADJUSTMENT
• Fixtures and tools for service ................4-12
1. Mechanism Assembly Mode Check ........4-13
2. Previous Preparation for
Deck Adjustment .....................................4-14
3. Torque Measuring ...................................4-14
4. Guide Roller Height Adjustment..............4-15
4-1. Prior Adjustment...............................4-15
4-2. Fine Adjustment ...............................4-15
5. Audio/Control (A/C) Head Adjustment......4-16
5-1. Prior Adjustment...............................4-16
5-2. Tape Path Check between Pinch
Roller and Take-up Guide ................4-17
5-3. Fine Adjustment
(Azimuth Adjustment).......................4-17
6. X-distance Adjustment ............................4-17
7. Adjustment after Drum Assembly
(Video Heads) .........................................4-18
8. Check of Traveling Device after Deck
Assembly .................................................4-18
8-1. Audio, RF Normalization Time
(Locking Time) Check in Play
after CUE or REV ............................4-18
8-2. Check of Tape Curl and
Jam Status .......................................4-18
PROTECTION, MAINTENANCE AND
CHECK OF VIDEO FUNCTION
1.
2.
3.
4.
5.
Checking Points before Repair ...............4-19
Essential Check and Repair....................4-20
Regular Check and Repair......................4-20
Tools for Check and Repair.....................4-20
Maintenance Process..............................4-20
5-1. Removal of Foreign Materials..........4-20
5-2. Grease Application...........................4-21
TROUBLESHOOTING GUIDE
1. Deck Mechanism.....................................4-23
2. Front Loading Mechanism.......................4-26
EXPLODED VIEWS
1. Front Loading Mechanism Section...........4-28
2. Moving Mechanism Section(1) .................4-29
3. Moving Mechanism Section(2) .................4-30
DECK MECHANISM PARTS LOCATIONS
• Top View
Procedure
Part
Starting
No.
9
2
2,3
2,3,4
2,3,4,5
4
2
3
6
5
10
8
12
11
18
1
16
33
17
19
14
2,3
2,3
2,3,13,14
17
17
15
17,18
13
35
7
21, 22
15
• Bottom View
20
32
21
31
31
24
32
21
25
24
34
28
23
27
22
29
30
26
21
21,22,23,
24,2526
21,22,23,
24,2526,27
21,22,23,
24,2526,27
21,22,23,
24,2526,27
25
2, 3, 14,
25, 31
25, 31
2,3,14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Drum Assembly
Plate Top
Holder Assembly CST
Gear Assembly Rack F/L
Opener Door
Arm Assembly F/L
Lever Assembly S/W
3 screws
2 hooks
6 chasses
1 hook
Chassis Hole
Chassis Hole
Chassis Hole,
1 hook
Motor Assembly L/D
1 screw
Gear Wheel
2 hooks
Arm Assembly Cleaner
Chassis Embossing
Head F/E
Chassis Embossing
Base Assembly A/C Head 1 screw
Brake Assembly T
1 hook
Arm Assembly Tension
1 hook
Reel S / Reel T
Shaft
Base Assembly P4
Chassis Embossing
Opener Lid
Chassis Embossing
Arm Assembly Pinch
Shaft
Arm T/up
1 hook
Supporter, capstan
Chassis Hole
Belt Capstan/Motor Capstan 3 screws
Lever F/R
Locking Tab
Clutch Assembly D37
Washer
Gear Drive/Gear Cam
Washer/Hook
Gear Sector
Hook
Brake Assembly Capstan Chassis Hole
Plate Slider
Chassis Guide
(1) When reassembling, confirm Mechanism and Mode
Switch Alignment Position
(2) When disassembling, the Parts in the "Starting No."
column should be removed first."
4-1
Ref. Posi
Draw- tion
ings
A-1
A-2
A-2
A-2
A-2
A-2
A-2
T
T
T
T
T
T
T
A-3
A-3
A-3
A-3
A-3
A-4
A-4
A-4
A-5
A-5
A-5
A-5
A-6
A-6
A-6
A-6
A-7
A-7
A-7
A-7
T
T
T
T
T
T
T
T
T
T
T
T
B
B
B
B
B
B
B
B
28 Lever Tension
1 Hook
A7
B
29 Lever Spring
1 Hook
A-7
B
30 Lever Brake
1 Hook
A-7
B
31 Gear Assembly P2/
Gear Assembly P3
32 Base Assembly P2
/Base Assembly P3
33 Base Loading
34 Base Tension
35 Arm Assembly Idler Jog
Bass
A-8
B
6 Chasses
A-8
B
3 Hooks
Chassis Embossing
Locking Tab
A-8
A-9
A-9
B
T
T
T:Top, B:Bottom
NOTE : When reassembling, perform the
procedure in the reverse order.
Fixing Type
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Drum Assembly
Flat Cable
(S1)
(S1)
(S1)
Cap, FPC
H2
H1
Holder FPC
Fig. A-1
1. Disassembly of Drum Assembly
(Figure A-1)
Cautions in assembly of FPC
1) Separate the flat cable from the Drum FPC and the
Capstan Motor.
2) Release 3 screws (S1) on the bottom side of the chassis,
and separate the drum assembly.
3) Release the hooks (H1, H2) and separate both the holder
FPC and the Cap FPC (disassemble if necessary).
Cap FPC
Drum FPC
Holder FPC
Assembly shape seen in the reverse direction
4-2
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Plate Top
(Fig. A-2-1)
(B')
(C)
(B)
Holder Assembly CST
(Fig. A-2-2)
(E)
Arm Assembly F/L
(Fig. A-2-5)
Lever Assembly S/W
(Fig. A-2-6)
(H4)
(E)
Opener Door
(Fig. A-2-4)
(H3)
Gear Assembly Rack F/L
(Fig. A-2-3)
Fig. A-2
4-3
(A)
(B)
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
2. Disassembly of Plate Top (Fig. A-2-1)
1) Separate the right part while leaning back the (B) part of
the plate top toward the arrow direction.
2) Separate the left part while leaning back the (B’) part of
the plate top toward the arrow direction.
(Tool used: Tool such as (-) driver, auger, etc with pointed or flat end)
4. Disassembly of Gear Assembly
Rack F/L (Fig. A-2-3)
1) Separate the hook (H3) while leaning ahead the hook (3)
after moving the gear assembly rack F/L toward the arrow
(A) direction.
2) Separate the gear assembly rack F/L toward the arrow (B)
direction.
CAUTIONS
CAUTIONS
Assemble while pressing the (C), (C’) part after corresponding them as in drawing.
For the assembly, correspond the gear part of gear assembly rack F/L to the gear drive.
Gear Rack F/L
(C')
(C)
(B')
(B)
Gear Drive
5. Opener Door (Fig. A-2-4)
3. Holder Assembly CST (Fig. A-2-2)
1) Firstly separate the left part from the groove on the (D)
part of chassis while moving the holder assembly CST
toward the arrow direction.
Holder Assembly CST
Chassis
(D)
1) Separate the opener door ahead from the guide hole of
chassis while turning it clockwise.
6. Arm Assembly F/L (Fig. A-2-5)
1) Firstly separate the left part of the arm assembly F/L from
the groove of chassis while pushing the arm assembly F/L
toward the arrow direction.
2) Separate the right part from the groove of chassis.).
7. Lever Assembly S/W (Fig. A-2-6)
1) Separate the lever assembly S/W while pushing it toward
the arrow direction after removing the hook (4) on the left
side of chassis.
Chassis
2) Separate the right part from each groove of chassis
CAUTIONS
(H4)
Assemble by inserting the left part after firstly inserting the
(E) part of the holder assembly CST into the groove on the
(E’) part of chassis.
4-4
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Arm Assembly Cleaner
(Fig. A-3-3)
(A)
(H5)
Gear Wheel
(Fig. A-3-2)
Base Assembly A/C Head
Motor Assembly L/D
(S5)
(Fig. A-3-5)
(Fig. A-3-1)
(A)
Head F/E
(C1)
(Fig. A-3-4)
(S4)
Fig. A-3
8. Motor Assembly L/D (Fig. A-3-1)
10. Arm Assembly Cleaner (Fig. A-3-3)
1) Take the connector (C1) connected to the Capstan motor
PCB out.
2) Remove a screw (S4) of the chassis (S4) and step backward, and disassemble it while holding it up.
1) Separate the (A) part of Fig. A-3-1 from the embossing of
chassis, and hold it up while turning it anti-clockwise.
9. Gear Wheel (Fig. A-3-2)
1) Release the hook (H5) of the gear wheel and disassemble
it upward.
11. Head F/E (Fig. A-3-4)
1) Separate the (A) part of the head F/E from the embossing of chassis, and hold it up while turning it anti-clockwise.
12. Base Assembly A/C Head (Fig. A-3-5)
1) Release a screw (S5) and disassemble while holding it up.
4-5
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Arm Assembly Tension
(Fig. A-4-2)
(H7)
Reel T
(Fig. A-4-3)
Reel S
(Fig. A-4-3)
Spring Tension
Brake Assembly T
Spring Tension
(Fig. A-4-1)
(H8)
(H6)
Fig. A-4
13. Brake Assembly T (Fig. A-4-1)
1) Release the spring tension from the lever spring hook
(H6).
2) Disassemble the brake assembly T while holding it
upward.
15. Reel S/Reel T (Fig. A-4-3)
1) Disassemble the reel S/ reel T while holding it up (comparison between Reel S and Reel T)
14. Arm Assembly Tension (Fig. A-4-2)
1) Release the spring tension the hook (H7) from the arm
assembly tension.
2) After releasing the hook (H8) of the base tension, separate it while holding it up.
Reel S
Reel T
CAUTIONS
Spring used for both brake assembly T and arm assembly
tension is used (2EA used).
4-6
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Opener Lid
(Fig. A-5-2)
(B)
Arm Assembly Pinch
(Fig. A-5-3)
(C)
Base Assembly P4
(C)
(Fig. A-5-1)
(H9)
Arm T/up
(A)
(Fig. A-5-4)
Chassis
Fig. A-5
16. Base Assembly P4 (Fig. A-5-1)
18. Arm Assembly Pinch (Fig. A-5-3)
1) Release the (A) part of the base assembly P4 from the
embossing of chassis.
2) Hold the base assembly P4 up while turning it anti-clockwise.
1) Hold the arm assembly pinch up.
17. Opener Lid (Fig. A-5-2)
1) Release the (B) part of the opener lid from the embossing
of chassis.
2) Disassemble the opener lid upward while turning it anticlockwise.
19. Arm T/up (Fig. A-5-4)
1) Turn the arm T/up to release the anchor jaw (H9) part of
chassis and then hold it upward.
CAUTIONS
For the assembly, check the (C) part of the arm assembly
pinch is assembled as in drawing.
- REVERSE THE MECHANISM.
4-7
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Suppoter Capstan
(Fig. A-6-1)
Belt Capstan
(Fig. A-6-2)
Motor Capstan
(Fig. A-6-3)
Washer(W1)
Clutch Assembly D37
(Fig. A-6-5)
(L1)
(L1)
Lever F/R
(Fig. A-6-4)
Chassis
(S6)
Fig. A-6
20. Supporter, Capstan (Fig. A-6-1)
22. Lever F/R (Fig. A-6-4)
1) Turn the supporter and Capstan by 90 deg. clockwise
with a driver for disassembly.
1) Release the locking tab (L1) and then disassemble it
upward.
21. Belt Capstan (Fig. A-6-2) /
Motor Capstan (Fig. A-6-3)
23. Clutch Assembly D37 (Fig. A-6-5)
1) Separate the belt Capstan.
2) Undo 3 screws (S6) on the bottom side of chassis and disassemble it upward.
1) Remove the washer (W1) and then disassemble it
upward.
4-8
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
(H10)
(H11)
Gear Sector
Gear Cam
(Fig. A-7-3)
(Fig. A-7-2)
(W2)
Washer (W2)
Brake Assembly Capstan
Gear Cam Hole(B)
(L2)
Gear Drive
(Fig. A-7-4)
(Fig. A-7-1)
Gear Drive Hole(A)
Plate Slider
(Fig. A-7-5)
Lever Tension
(Fig. A-7-6)
Lever Brack
(Fig. A-7-8)
(B)
Lever spring
(Fig. A-7-7)
Base Loading
Gear Cam Hole(C)
(A)
Chassis
Fig. A-7
24. Gear Drive (Fig. A-7-1)/
Gear Cam (Fig. A-7-2)
1) Release the locking tab (L2) on the bottom side of the
plate slider and then disassemble it upward.
1) Remove the washer (W2) and then disassemble the
gear drive.
2) Release the hook (H10) of the gear cam and then disassemble it upward.
27. Plate Slider (Fig. A-7-5)
CAUTIONS
For the assembly, adjust both the gear driver hole (A) and
the gear cam hole (B) straightly and then correspond the
gear cam hole (C) to the chassis hole.
25. Gear Sector (Fig. A-7-3)
1) Release the hook (H11) of the gear sector and then hold
the gear sector upward.
26. Brake Assembly Capstan (Fig. A-7-4)
4-9
1) Disassemble the plate slider while holding it up.
28. Lever Tension (Fig. A-7-6)
1) Release the lever tension from the guide (A) of chassis
while turning it anti-clockwise.
2) Disassemble the lever tension while holding it up.
29. Lever Spring (Fig. A-7-7)
1) Release the (B) part of the lever spring from the guide
(A) of chassis while turning it anti-clockwise.
2) Disassemble the lever tension while holding it up.
30. Lever Brake (Fig. A-7-8)
1) Disassemble the lever brake while holding it up.
DECK MECHANISM DISASSEMBLY
Gear assembly P2 Hole
Gear assembly P3 Hole
Gear Assembly P3
(Fig. A-8-2)
Gear Assembly P2
(Fig. A-8-1)
(H12)
(H13)
Lever Tension Boss
Plate slider Hole(B)
(H14)
Base Loading
(Fig. A-8-5)
(B)
(A)
Chassis
Base Assembly P3
(Fig. A-8-4)
Base Assembly P2
(Fig. A-8-3)
Fig. A-8
31. Gear Assembly P2 (Fig. A-8-1)/
Gear Assembly P3 (Fig. A-8-2)
32. Base Assembly P2 (Fig. A-8-3)/
Base Assembly P3 (Fig. A-8-4)
1) Hold the gear assembly P2 upward.
2) Hold the gear assembly P3 upward.
1) Disassemble the base assembly P2 downward while moving it toward the arrow (A) direction along with the guide
hole of chassis.
2) Disassemble the base assembly P2 downward while moving it toward the arrow (B) direction along with the guide
hole of chassis.
CAUTIONS
For the assembly, check the holes of both the gear assembly P2 and the P3 are adjusted straightly, and then correspond the gear section groove (A) to the plate slider hole (B).
33. Base Loading (Fig. A-8-5)
1) Release 3 hooks (H12, 13, 14) of the base loading, and
then disassemble them upward.
- Reverse the mechanism.
4-10
DISASSEMBLY AND ASSEMBLY OF DECK MECHANISM
Base Tension
(Fig. A-9-1)
Arm Assembly Idler Jog
(A)
(Fig. A-9-2)
(B)
(C)
Chassis
(D)
Fig. A-9
34. Base Tension (Fig. A-9-1)
35. Arm assembly Idler Jog (Fig. A-9-2)
1) Release the (A) part of the base tension from the
embossing of chassis.
2) Hold the base tension upward while turning it anti-clockwise.
1) Push both (B), (C) parts in Fig. A-9-2 toward the arrow
direction.
2) Disassemble the arm assembly idler upward.
CAUTIONS
Take care to ensure that the (D) part in the drawing is not
hung to chassis in disassembly.
4-11
DECK MECHANISM ADJUSTMENT
• Fixtures and Tools for Service
SR K
1. Cassette Torque Meter
SRK-VHT-303(Not SVC part)
Part No:D00-D006
-V
HT
-S
2. Alignment tape
Part No NTSC:DTN-0001
PAL:DTN-0002
3. Torque gauge
600g.Cm ATG
Part No:D00-D002
5. Post height adjusting driver
Part No:DTL-0005
6. + Type driver (ø5)
300
250
200
150
SR
K
0 50
VID
CAS EO
S
TOR ETTE
Q
MET UE
VHT ER
-303
-T
K- V HT0
SR
50
100
150
200
300
250
4. Torque gauge adaptor
Part No:D09-R001
4-12
DECK MECHANISM ADJUSTMENT
1. Mechanism Assembly Mode Check
Purpose of adjustment : To make tools normally operate by positioning tools accurately.
Fixtures and tools used
• Blank Tape (empty tape)
VCR (VCP) status
Checking Position
• Eject Mode
(with cassette withdrawn)
1) Turn the VCR on and take the tape out by pressing the
eject button.
2) Separate both top cover and plate top, and check both
the hole (A) of gear cam and the hole (A’) of chassis correspond (Fig. C-2).
3) If it is done as in the paragraph 2): Turn the gear cam as
in No.2) after mantling the motor assembly L/D.
• Mechanism and Mode Switch
4) Undo the screw fixing the deck and the main frame, and
separate the deck assembly. Check both the hole (A) of
gear cam and the hole (A’) of chassis correspond (Fig.
C-1).
5) Check the mode S/W on the main P.C. board locates at
a proper position as in (B) of the Fig. (C-1).
6) Connect the deck to the main P.C. board and perform all
types of test.
CHECK DIAGRAM
Mode S/W
Gear Cam
(C)
(B)
Gear Drive
Correspondence of the gear cam hole (O)
and the gear drive hole (O)
BOTTOM VIEW
Fig. C-1
Motor Assembly L/D
Gear Cam
(A')
(A)
Chassis Hole
TOP VIEW
Fig. C-2
4-13
Gear Cam Hole
DECK MECHANISM ADJUSTMENT
2. Previous Preparation for Deck Adjustment
(Preparation to load the VCR (VCP) with cassette tape not inserted)
1) Take the power cord from the consent.
2) Separate the top cover and the plate assembly top.
3) Insert the power cord into again.
4) Turn the VCR (VCP) on and load the cassette while pushing the lever stopper of the holder assembly CST backward. In this case, clog both holes on the housing
rail part of chassis to prevent detection of the end sensor.
If doing so, proceeding to the stop mode is done. In this
status, input signals of all modes can be received.
However, operation of the Rewind and the Review is
impossible since the take-up reel remains at stop status
and so cannot detect the reel pulse (however, possible for
several seconds).
3. Torque Measuring
Purpose of Measuring : To measure and check the reel torque on the take-up part and the
supply part that performs basic operation of the VCR (VCP) for
smoothly forwarding the tape.
Measure and check followings when the tape is not smoothly
wound or the tape velocity is abnormally proceeded:
Fixtures and tools used
• Torque Gauge
(600 g.cm ATG)
• Torque Gauge Adaptor
• Cassette Torque Meter
SRK-VHT-303
Item
VCR (VCP) status
• Play (FF) or Review
(REW) Mode
Mode
Measuring method
• Try to operate the VCR (VCP) per mode with the
tape not inserted (See ‘2. Prior Preparation for
Deck Adjustment).
• Measure after adhering and fixing the torque
gauge adaptor to the torque gauge (Fig. C-3-1)
• Read scale of the supply or take-up part of the
cassette torque meter (Fig. C-3-2).
Instruments
Reel Measured
Measuring Value
Fast forward Torque Fast Forward
Torque Gauge
Take-Up Reel
More than 400g°cm
Rewind Torque
Torque Gauge
Supply Reel
More than 400g°cm
Play Take-Up Torque Play
VHT-303
Take-Up Reel
40~100g°cm
Review Torque
VHT-303
Supply Reel
120~210g°cm
Rewind
Review
NOTE
Adhere the torque gauge adaptor to the torque gauge for measuring the value.
• Torque Gauge (600g.cm ATG)
• Cassette Torque Meter (SRK-VHT-303)
SR K
Torque Gauge
-V
HT
-S
300
250
200
150
SR
K
Torque Gauge
Adaptor
0 50
VID
CAS EO
S
TOR ETTE
Q
MET UE
VHT ER
-303
-T
K- V HT0
SR
50
100
150
200
300
250
Reel Table
Fig. C-3-1
Fig. C-3-2
4-14
DECK MECHANISM ADJUSTMENT
4. Guide Roller Height Adjustment
Purpose of adjustment : To ensure that the bottom surface of the tape can travel along with
the tape lead line of the lower drum by constantly and adjusting
and maintaining the height of the tape.
4-1. Prior Adjustment
Fixtures and tools used
• Post Height Adjusting
Driver
VCR (VCP) status
• Play or Review Mode
Adjustment Procedure
Adjustment position
• The guide roller height adjusting screw on the
supply guide roller and the take-up guide roller
ADJUSTMENT DIAGRAM
1) Travel the tape and check the bottom surface of the
tape travels along with the guide line of the lower drum.
2) If the tape travels toward the lower part of guide line on
the lower drum, turn the guide roller height adjusting
screw to the left
3) If it travels to the upper part, turn it to the right.
4) Adjust the height of the guide roller to ensure that the
tape is guided on the guide line of the lower drum at the
inlet/outlet of the drum. (Fig. C-4-1)
GUIDE ROLLER
HEIGHT
ADJUSTMENT SCREW
Fig. C-4-1
4-2. Fine Adjustment
Fixtures and tools used
• Oscilloscope
• Standard test tape
• Post height adjusting
driver
Measuring tools and
connection position
VCR (VCP) status
• CH-1: PB RF Envelope • Play the standard test
tape.
• CH-2: NTSC : SW 30Hz
PAL : SW 25Hz
Waveform
• Head switching output
P2 POST ADJUSTMENT
point
• RF Envelope output
point
1) Play the standard test tape after connecting the probe of
oscilloscope to the RF envelope output point and the
head switching output point.
2) Tracking control (playback) : Locate it at the center
(Set the RF output to the maximum value via the tracking control when such adjustment is completed after the
drum assembly is replaced.)
3) Height adjusting screw: Flatten the RF waveform.
(Fig. C-4-2)
4) Move the tracking control (playback) to the right/left.
(Fig. C-4-3)
5) Check the start and the end of the RF output reduction
width are constant.
CAUTIONS
Adjustment position
• Guide roller height
adjusting screw
P3 POST ADJUSTMENT
Fig. C-4-2
When the tracking control
locates at the center.
Flatten the waveform by
lightly turning the
guide roller height adjustment screw.
When turning the tracking
control to both sides.
Fig. C-4-2
Connection Diagram
There must exist no crumpling and folding of the tape due
to excess adjustment or insufficient adjustment.
OSCILLOSCOPE
RF ENVELOPE OUTPUT POINT
CH-1
HEAD RF SWITCHING OUTPUT POINT
4-15
CH-2
DECK MECHANISM ADJUSTMENT
5. Audio/Control (A/C) Head Adjustment
Purpose of adjustment : To ensure that audio and control signals can be recorded and
played according to the contract tract by constantly maintaining
distance between tape and head, and tape tension between the P3
post and the P4 post.
5-1. Prior Adjustment (performed only when no audio output appears in play of the standard test tape)
Fixtures and tools used
• Blank Tape
(Empty Tape)
• Driver (+) Type ø 5
VCR (VCP) status
• Play the blank tape
(empty tape).
Adjustment Procedure/Adjustment Diagrams
1) Basically use the A/C head assembly adjusted as in
SPEC.
2) Check there is crumpling and folding of the tape around
the A/C head. If it is, Turn and adjust the tilt adjusting
screw to ensure that the tape corresponds to the bottom
guide of the P4, and recheck the tape path after proceeding play for 4-5 seconds.
Adjustment position
• Tilt adjusting screw (C)
• Height adjusting screw (B)
• Azimuth adjusting screw (A)
3) Where the tape bottom is not equal to Fig. C-5-3, Adjust
the height by using the height adjusting screw (B) and
then readjust it by using the tilt adjusting screw (C).
CAUTIONS
Always check the height of the A/C head since most ideal
height of A/C head can be obtained when the bottom part
of the tape is away 0.2 ~ 0.25mm from the bottom part of
the A/C head.
Tape
A/C Head
8.3
P4
Tape
0.2~0.25mm
A/C Head Base
Fig. C-5-1
Fig. C-5-3
X-Value Adjustment
Hole
Fixed Screw
Azimuth
Adjustment
Screw(A)
Tilt Adjustment
Screw(C)
Height Adjustment
Screw(B)
A/C Head Assembly
Fig. C-5-2
4-16
DECK MECHANISM ADJUSTMENT
5-2. Tape Path Check between Pinch Roller and
Take up Guide (Check in the Rev Mode)
1) Check the tape pass status between the pinch roller and
the take-up guide.(Check there is crumpling of the tape
pass and folding of the take-up guide.)
1) (1) When holding of the take-up guide bottom occurs
Turn the tilt adjusting screw (C) clockwise and travel it
stably to ensure there is no crumbling or folding of the
tape.
1) (2) When holding of the take-up guide top occurs
Turn the tilt adjusting screw (C) anti-clockwise and
travel it stably to ensure there is no crumbling or folding of the tape.
1) 2) Check there is folding of the tape at the bottom or top
of the take-up guide in cutting-off the REV mode
CAUTIONS
If the RF waveform is changed after adjusting the A/C head,
perform fine adjustment to ensure the RF waveform is flattened.
5-3. Fine Adjustment (Azimuth Adjustment)
Fixtures and tools used
• Oscilloscope
• Standard test tape
(only for SP)
• Driver (+) Type Ø 4
Connection position
• Audio Output Jack
VCR (VCP) status
Adjustment position
• Play the standard test
• Tape, 1KHz, 7KHz.
• Azimuth Adjusting
Screw (A)
• Height Adjusting Screw
(B)
Adjustment Procedure
1KHz
1) Connect the probe of Oscilloscope to the audio output
jack.
2) Ensure that Audio 1KHz, 7KHz output is flattened at the
maximization point by adjusting the Azimuth adjusting
screw (A).
7KHz
A: Maximum
B: Minimum
Fig. C-5-4
6. X-distance Adjustment
Purpose of adjustment : To maintain compatibility with other VCR (VCP).
Fixtures and tools used
• Oscilloscope
• Standard test tape
(only for SP)
• Driver (+) Type Ø 4
Connection position
VCR (VCP) status
Adjustment position
• CH-1: PB RF Envelope • Play the standard test
• CH-2: NTSC ; SW 30Hz
tape.
PAL:SW 25Hz
• Head switching output
point
• RF Envelope output
point
Adjustment Procedure
1) After releasing the auto tracking, lightly turn the fixing
screw. Turn the (+) type driver (Ø 3 ~ Ø 4) on the X-distance adjusting hole to the right or left. Adjust the RF
envelope level to the maximum point and then fix the fixing screws.
2) For the 31mm head, adjust it with the SP tape recorded
in the width of 31mm since the head travels on the tape
track only for SP with the width of 58mm.
Left
Grove of Base A/C
Right
Connection Diagram
X-distance Adjusting Hole
Fixing Screw
Azimuth
Adjustment
Screw(A)
Tilt Adjusting Screw (C)
Height Adjusting
Screw (B)
Fig. C-6
OSCILLOSCOPE
RF ENVELOPE OUTPUT POINT
CH-1
HEAD RF SWITCHING OUTPUT POINT
4-17
CH-2
DECK MECHANISM ADJUSTMENT
7. Adjustment after Drum Assembly (Video Heads)
Purpose of adjustment : To adjust and stabilize the height change, X-distance change, etc
depending on the guide roller after assembling the drum.
Fixtures and tools used
• Oscilloscope
• Standard test tape
(only for SP)
• Post Height Adjusting
Driver
• Driver (+) Type Ø 5
Connection position
VCR (VCP) status
Adjustment position
• CH-1: PB RF Envelope • Play the blank tape.
• CH-2: NTSC : SW 30Hz • Play the standard test
PAL:SW 25Hz
tape.
• Head switching output
point
• RF Envelope output
point
• Fine adjustment of
guide roller
• Switching Point
• Tracking Preset
• X-distance
Connection Diagram
Checking/Adjustment Procedure
1) Play the blank tape (empty tape) and check whether the
guide roller crumbles or wrinkles the tape and adjust it if
necessary.
2) Check that the RF envelope output waveform is flat, and
adjust the height of the guide roller while playing the
standard test tape.
3) Adjust the switching point.
4) Check the RF envelope output is the maximum when
the tracking control locates at the center. If not maximum, set up to ensure that RF envelope output
becomes the maximum by turning the (+) type driver (Ø
3 ~ Ø 4) on the base A/C groove.
OSCILLOSCOPE
RF ENVELOPE OUTPUT POINT
CH-1
CH-2
HEAD RF SWITCHING OUTPUT POINT
Waveform
V1/V MAX = 0.7
V1/V MAX = 0.8
V1
RF ENVELOPE OUTPUT
V1
V2
8. Check of Traveling Device after Deck Assembly
8-1. Audio, RF Normalization Time (Locking Time) Check in Play after CUE or REV
Fixtures and tools used
• Oscilloscope
• 6H 3KHz Color Bar
Standard Test tape
• Stop Watch
Measuring standard
Connection position
VCR (VCP) status
• RF Locking Time: Within • CH-1: PB RF Envelope
• CH-2: Audio output
5 seconds
• RF Envelope output
• Audio Locking Time :
point
Within 10 seconds
• Audio output jack
• Play the 6H 3KHz
Color Bar Standard
Test tape.
Checking Procedure
1) Check that locking time of the RF and Audio waveform is
fallen within the measuring standard in conversion of the
play mode from the CUE or the REV mode.
2) Readjust the paragraph 5 and 6 if it deviates from the
standard.
8-2. Check of Tape Curl and Jam Status
Fixtures and tools used
• T-160 Tape
• T-120 Tape
Fixtures and tools used
Fixtures and tools used
• There must be no jam or curl at the
first, middle and end position of tape.
• Travel the tape at the position
of its first and end.
Checking Procedure
1) Check there is no abnormality of every traveling post
status.
2) There must be no abnormal operation of the counter in
occurrence of folding of the bottom tape. There must be
not abnormality of audio signal in damage of the top tape.
3) If there is abnormality, readjust the adjustment paragraph 4 and 5.
4-18
PROTECTION, MAINTENANCE AND CHECK OF VIDEO FUNCTION
1. Checking Points prior to Repair
Following abnormal phenomena may be repaired by
removal of foreign materials and oil supply. Check oiling is
required at the checking set or cleaning status is complete.
Determine that necessity of checking and repair the set
exists after checking the using period of the set together
with the user. In this case, followings must be checked:
Phenomena
Checking Points and
Cause
Replacement
Color beat
Pollution of Full-Erase Head
o
S/N, Color Faded
Pollution of Video Head
o
F/E Head
Video Head
Horizontal, Vertical Jitte
Pollution of Video Head or
Tape Transport System
o
Poor Sound, Low Sound
Pollution of Audio/Control
Head
o
No tape wound or tape
wound loosely.
Pollution of Pinch Roller or
FF or REW impossible, Belt Capstan Belt
or slow turning
Tape loosely wound in
REV or Unloading
Deterioration of Clutch
Assembly D37 Torque
Pollution of Drum and
Traveling Device
Fig. C-9-1 TOP VIEW
A/C Head
Pinch Roller
o
o
Belt Capston
Clutch
Assembly A37
Fig. C-9-3
CAUTIONS
If operation of the position with (O) mark is abnormal even
after removing cause, replace it with substitute product since
it shows damage or wearing.
Fig. C-9-2 BOTTOM VIEW
* No. (1) ~ (12) shows sequence that the tape moves from the supply reel to the take-up reel.)
(6) Base Assembly
P3
(7) A/C Head
(3) F/E Head
(8) P4 Post
(5) Drum Assembly
(Video Head)
(10) Pinch Roller
(11) Take-up Guide
Post
(4) Base Assembly P2
(2) Tension Post
(9) Capstan Shaft
(1) Supply Reel
(12) Take-up Reel
Fig. C-9-3 Tape Transport System
4-19
PROTECTION, MAINTENANCE AND CHECK OF VIDEO FUNCTION
2. Essential Check and Repair
4. Tools for Check and Repair
Recording density of the video is far higher than the audio.
Therefore video parts are very precise so as to allow only
error of 1/1000mm or so in order to maintain compatibility
with other videos.
If one of these parts is polluted or old, same phenomena will
appear as they are damaged.
To maintain clear screen, regular check, replacement of old
and damaged parts and oil supply, etc are essential.
(1) Grease: Floil G-3114 (KANTO) or equivalent grease
(Green)
(2) Grease: Kanto G-754, PL-433 (Yellow)
(3) Alcohol (Isopropyl Alcohol)
(4) Cleaning Patch (cloth)
3. Regular Check and Repair
Check and repair schedule is not constant since they vary
depending on method that the consumer uses video and
environment where the video is installed at.
However, for the video used by common household, good
screen will be maintained if regular check and repair per
1,000 hour is performed. The following chart shows relationship between using time and checking time:
Table 1
Time
Requiring
Checking
About
1 year
About
18 months
About
3 years
5. Maintenance Process
5-1) Removal of Foreign Material
(1) Removal of foreign material from video head (Fig. C-9-4)
Firstly try to use a cleaning tape.
(1) Use a cleaning patch if foreign materials are not removed
with the cleaning tape due to severe dirty of the head.
Soak the cleaning patch in alcohol and put it to the head
tip. Smoothly turn the drum (turning cylinder) to the right
or left (In this case, the cleaning patch must not be
moved vertically).
(1) After completely drying the head, test the traveling status
of the tape.
(1) If alcohol (Isopropyl Alcohol) remains at the video head,
the tape may be damaged when this solution touches
with the head surface.
Never use a cloth bar (commercial sale)
Average
hours used
per day
(2) Wipe the tape transport system and the drive system
with the cleaning patch soaked in alcohol (Isopropyl
Alcohol) when removing foreign materials from them.
1) The part touched with the traveling tape is called as
tape transport system. The drive system consists of
parts to travel the tape.
(2) 2) Care must be exercised so that unreasonable force
to change the pattern will be applied to the tape transport system during removal of foreign materials.
One hour
Two hours
Three hours
Drum
(Turning Cylinder)
Cleaning Patch
(Cloth)
Head Tip
Soak alcohol
(Isopropyl Alcohol).
Smoothly turn the drum (turning
cylinder) touching the soft surface
to the head tip surface.
Fig. C-9-4
4-20
PROTECTION, MAINTENANCE AND CHECK OF VIDEO FUNCTION
5-2) Grease Applications
(1) Grease Application Method
Apply grease by using a cloth swab or brush. Care must
be exercised so that excess quantity should not be
used. If the excessive quantity is applied, wipe it with
the gauze soaked in alcohol (Isopropyl Alcohol).
NOTE: POSITION OF GREASE APPLICATION
(1) Inner Side Surface and Top
Surface of Loading Path
(2) Stable Adhesion Part of Base
P2, P3
(3) Arm Pinch Shaft
(4) Gear Wheel Shaft
(5) Reel S. T. Shaft
(1) (2) (3) (4): KG-684G
(Green)
(5): PL-433 (Yellow)
(2) Regular Grease Application
Apply grease to the designated application position
every 500 hour.
(1) Inner Side Surface and Top
Surface of Loading Path
(2) Stable Adhesion Part of Base
P2, P3 Coil
(3) Gear Cam Shaft
(4) Gear Drive Shaft
(5) Clutch Shaft Groove
(6) Guide Part on the Plate Slider
Side Wall (Left)
(7) Guide Part on the Plate Slider
Side Wall (Right)
(1) (2) (3) (4) (5) (6) (7): KG684G (Green)
2
2
1
4
1
3
3
4
6
5
7
Chassis (Bottom)
5
Chassis (TOP)
Gear Part
Cam Part
(PL-433.Yellow)
Gear Part
(PL-433.Yellow)
Gear Sector
Cam Part Side Application
(KG-684G.Green) Gear
Cam
Cam Part
(KG-684G , GREEN)
Cam Part
(KG-684G , GREEN)
Boss Part Side Wall
(PL-433.Yellow)
Gear Rack F/L
Gear Part Side Application
(PL-433.Yellow)
Base Loading
Gear Drive
Lever Tension Driving Cam Part
Lever, Brake Driving Cam Part
Gear Sector Driving Part
Inner Surface of
Guide Rail
(KG-684G.Green)
Lever F/R Driving Part
Side Wall Guide Part
Chassis (L)
4-21
Chassis (R)
Side Wall Guide Part
Lever, Spring Driving Part
Plate Slider
PROTECTION, MAINTENANCE AND CHECK OF VIDEO FUNCTION
Lever, F/R, Base, Tension
GEAR AY, P2 & P3
PL-433
LEVER, F/R
BASE, TENSION
Clutch Contact Part
(PL-433, Yellow)
Tension Arm Party
Hinge Part (PL-433, Yellow)
4-22
MECHANISM TROUBLESHOOTING GUIDE
1.Deck Mechanism
A.
Auto REW doesn't work.
YES
Is the supply to the END sensor
END sensor "H"?
“H”: more than 3.5V
“L”: less than 0.7V~1V
YES
NO
Is the Vcc. voltage of End sensor 5V?
NO
Check the syscon power.
YES
Replace End sensor.
Is the voltage across IR LED
between 0.8~1.5V?
NO
Replace LED.
YES
Check syscon circuit.
B.
No F/R modes.
YES
Is the present mode, F/R
Mode?
NO
Is the mode SW assembled
correctly (refer to Pages 4-14.)
YES
NO
Does the Capstan Motor rotate?
YES
Does the T/Up, Supply Reel
rotate?
YES
Check syscon circuit.
4-23
Is the normal voltage supplied
to the Capstan Motor Vcc1,
Vcc2.?
YES
Is terminal voltage (Vctl) of
Capstan Motor supply side
more than 4V?
YES
Replace the Capstan Motor.
NO
Check Servo, Power Circuits.
MECHANISM TROUBLESHOOTING GUIDE
C.
AUTO STOP.
(PLAY/CUE/REV)
Check aligment positions (page
4-14) Check Pinch spring.
In Play/Cue/Rev is the pinch
roller in contact with the capstan shaft.
NO
Is the output of DFG, DPG OK?
YES
Are there T/up and supply reel
pulses.
Replace Drum Motor.
NO
YES
NO
Check Servo, Syscon.
YES
Check the Syscon, µ-COM.
Replace Reel Sensor.
D.
No cassette loading.
Insert the cassette.
YES
Does the lever Assembly S/W
work normally.
NO
Check CST Holder Assembly.
YES
Is there variation for CST IN
S/W Output?
(In Tape with REC Tab
“L”c"“H”" “L”)
(In Tape without REC Tab
“L”" “H”" “L”" “H”)
NO
Does the CST IN S/W work
normally?
NO
Replace CST IN S/W.
YES
YES
NO
Check Syscon Circuit.
Check Syscon Circuit.
4-24
MECHANISM TROUBLESHOOTING GUIDE
E.
In PB mode Tape Presence
not sensed.
Is the Pinch Roller attached to
the Capstan Motor Shaft?
NO
Check Alignment positions
(page 4-14)
YES
NO
Does the T/Up Reel turn?
NO
Is the Belt ok?
YES
Replace the Belt.
YES
Check the clutch and the Idler
Assembly.
Does the Capstan Motor turn?
YES
Does the Drum Motor turn?
NO
YES
Is the Voltage supplied to the
Capstan Motor Vcc1,Vcc2 each?
YES
Is the terminal voltage of
Capstan Motor supplied more
than 4V?
Are there DPG, DFG Pulses?
YES
NO
Check Servo, Power.
YES
Are the T/Up Supply Reel
Sensors ok?
Replace the Capstan Motor.
YES
NO
Check Servo, Syscon.
Is the Vcc voltage of the Drum
Motor normal?
NO
Check Syscon, Circuit.
YES
Is the terminal voltage of the
Drum Motor more than 2.3V?
YES
Replace the Drum Motor.
4-25
NO
Check Syscon, Circuit.
MECHANISM TROUBLESHOOTING GUIDE
2. Front Loading Mechanism
A.
Cassette cannot be inserted.
Does the Lever Assembly
Switch work?
NO
Is the Lever Assembly Switch
Spring damaged or omitted?
YES
YES
Does the CST IN Switch work
normally?
Is the Vcc of Main P.C.Board
5V?
NO
Replace or add the Lever
Assembly Switch Spring.
NO
Replace CST IN Switch.
YES
Check syscon circuit.
NO
YES
Is the voltage between cassette
switch and GND on Main
P.C.Board 5V??
Check power circuit.
NO
YES
Check Mode switch location
and syscon circuit.
Is there a short circuit between cassette switch
and GND on main P.C.Board?
NO
YES
Remove the short circuit part or
Replace the main P.C.Board.
Replace CST IN Switch.
B.
Cassette will not eject.
Does the L/D motor rotate in reverse?
NO
Check L/D Motor or Drive IC.
YES
Does the Lever Assembly Switch work?
NO
Replace lever Assembly Switch.
YES
NO
Does the F/L Arm Assembly work normally?
Replace F/L Arm Assembly .
YES
NO
Does the Door Opener work?
Replace the Door Opener.
4-26
MECHANISM TROUBLESHOOTING GUIDE
C.
Cassette will not load.
Does the CST insert?
YES
Does the CST insert?
YES
NO
Replace the Lid Opener.
Does the F/L Gear Rack work?
YES
NO
Does the Door Opener work?
YES
NO
Does the F/L Arm Assembly work?
YES
Check the power of L/D Motor.
NO
Replace the Front Loading Mechanism
Assembly.
4-27
Replace the F/L Arm Assembly.
NO
Does the Cassette Holder Assembly
move the F/L Arm Assembly?
YES
Is the Door opener assembled correctly?
NO
Does the L/D Motor work?
YES
Replace the F/L Rear Rack.
Is the Cassette Holder Assembly
assembled correctly?
EXPLODED VIEWS
1. Front Loading Mechanism Section
103
110
116
115
A24
105
112
113
106
102
100
114
032
107
A23
A21
109
054
A22
054A
4-28
EXPLODED VIEWS
2. Moving Mechanism Section (1)
OPTIONAL PART
031
079
011
017
022
032
A01
003
012
024
004
008
406
006
A03
409
007
013
016
014
015
009
405
027
026
028
031
029
021
4-29
EXPLODED VIEWS
3. Moving Mechanism Section (2)
518
055
060
051
080
056
058
052
061
052A
517
410
064
A11
067
077
066
065
032
068
070
069
023
A12
076
078
4-30
NOTES) If you want to purchase
NOTES)
Flash memory, you must order
" IC604A "
Warning
Parts that are shaded are critical with
respect to risk of fire or electrical
shock.
SECTION 5 REPLACEMENT PARTS LIST
MODEL : XBV613(LGEUS)
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
RUN DATE : 23-JANUARY-06
REMARKS
*** INDIVIDUAL PARTS ***
250
3110R-V024B
CASE
VBW8024 PRESS TOP A288G B:3,S:
271
3300R-V151A
PLATE
COMBI-4 PRESS MD MOTOR GND
273
3300R-V149A
PLATE
COMBI4 PRESS GND(DECK+MAIN)
274
3300R-V075A
PLATE
ONE BOARD SLIM PRESS A/V JACK
300
6410RAHP01A
POWER CORD
SPT-2 NON I. 18AWG PT.HARNESSI
457
1SZZR-0098E
SCREW,DRAWING
+ 2 D3.0 L12.0 MSWR3/FZMCW-1 3
463
1SZZR-0098G
SCREW,DRAWING
+ 2 D3.0 L8.0 MSWR3/FZMCW-1 3C
463
1SZZR-0098G
SCREW,DRAWING
+ 2 D3.0 L8.0 MSWR3/FZMCW-1 3C
465
1SZZR-0097K
SCREW,DRAWING
+ 2 D3.0 L10.0 MSWR3/FZB 3 CR
469
1SZZR-0098J
SCREW,DRAWING
+ 2 D3.0 L6.5 MSWR3/FZMCY-1 3
470
1SZZR-0098K
SCREW,DRAWING
+ 2 D3.0 21MM MSWR3/FZMCY-1 3C
471
1SZZR-0098L
SCREW,DRAWING
+ 2 D3.0 L16.0 MSWR3/FN SILVER
801
3835RV0051D
INSTRUCTION ASSEMBLY
VCR V1310MZ.NA1ULZ
802
3890RNC005X
BOX,MASTER
V1310MZ. NA1ULZ SWM3-A LGEUSZE
803
3920R-E168A
PACKING
VCR COMBIV9 130 COMBI
804
292-053B
BAG
SOFT(MIDI)
808
534-008C
BATTERY,MANGANESE
AAAM(R03) SEOTONG 1-5 V - 1PA
900
6711R1P081K
REMOTE CONTROLLER ASSEMBLY
N6 V1310MZ.NA1ULZ ZENITH
NSP
*** PANEL ASSEMBLY,FRONT ***
A43
3721R-F924F
PANEL ASSEMBLY,FRONT
VCR V1310MZ NA1ULZ ZENITH 2006
280
3720R-F934E
PANEL,FRONT
VCR V1310MZ NA1ULZ MOLD ZENITH
283
3580R-V117E
DOOR
VCR V1310MZ NA1ULZ MOLD HF-380
284
442-681A
SPRING
DOOR
285
3580R-T148C
DOOR
VCR V1310MZ NA1ULZ MOLD HF-380
286
4970R-0146A
SPRING
PLATE DR4000 SPRING
NSP
*** CABLE ASSEMBLY ***
810
6851R-0039B
CABLE ASSEMBLY
NTSC RF 1.8M + 1W YELLOW 1.8M
806
6850R-CAA8E
CABLE,COAXIAL
RF CABLE NTSC KOREA/AMERICA/JA
811
6850R-PAA8F
CABLE,COAXIAL
1 WAY COAXIAL DT_HY_HIT_SEIL 1
812
6850R-PBA8H
CABLE,COAXIAL
2 WAY COAXIAL RED_WHITE DT_HY
*** DECK ASSEMBLY,VIDEO ***
A00
6721RF0943K
DECK ASSEMBLY,VIDEO
DECK/MECHA D37(N) DI(4HF,NT,AH
009
4260R-0056A
ARM
DECK/MECHA T/UP OTHER - D37
012
3041R-M037A
BASE ASSEMBLY
P2 -D37
012
3041R-M037B
BASE ASSEMBLY
P2 - D37
013
3041R-M038A
BASE ASSEMBLY
P3 - D37
013
3041R-M038B
BASE ASSEMBLY
P3 - D37
014
3041R-M039A
BASE ASSEMBLY
P4 - D37
NSP
ALTERNATE
ALTERNATE
016
3041R-M036D
BASE ASSEMBLY
A/C HEAD (ALPS) - D37 (DUMMY H
016
3041R-M036E
BASE ASSEMBLY
A/C HEAD (TDK) - D37 (DUMMY HE
023
3040R-M056A
BASE
LOADING OTHER - D37
029
4261R-0037A
ARM ASSEMBLY
DECK/MECHA PINCH - D37 (CHON P
029
4261R-0037B
ARM ASSEMBLY
DECK/MECHA PINCH - D37 (YAMAUC
ALTERNATE
029
4261R-0037C
ARM ASSEMBLY
DECK/MECHA PINCH - D37 (MEIJI)
ALTERNATE
029
4261R-0037D
ARM ASSEMBLY
DECK/MECHA PINCH - D37 (CHON
ALTERNATE
032
3141R-M002A
CHASSIS ASSEMBLY
D37
077
3300R-M203A
PLATE
SLIDER OTHER - D37
5 - 1
ALTERNATE
NSP
S AL LOCA. NO. PART NO.
079
3040R-M057A
DESCRIPTION
SPECIFICATION
BASE
TENSION OTHER - D37
100
3301R-M193A
PLATE ASSEMBLY
TOP - D37
405
1MPC0301270
SCREW MACHINE,PAN HEAD
+ D3.0 L3.5 SWRCH18A/FZW
406
1MEC0302018
SCREW MACHINE,PAN HEAD SPR W
+ D3.0 L6.0 MSWR3/FZY
409
1SZZR-0032B
SCREW,DRAWING
+ 1 D2.6 L5.0 SWRCH18A/FZY TAP
410
1APF0262218
SCREW TAP TITE(B),PAN HEAD
+ D2.6 L6.8 MSWR3/FZY
517
1WZZR-0004D
WASHER,DRAWING
STOPPER
517
1WZZR-0004F
WASHER,DRAWING
DECK/MECHA D37 OTHER STOPPER
518
1WZZR-0004A
WASHER,DRAWING
STOPPER
A23
4261R-0038A
ARM ASSEMBLY
DECK/MECHA F/L - D37
110
4260R-0051A
ARM
DECK/MECHA F/L(L) OTHER - D37
112
3070R-0002A
BODY
F/L
113
4970R-0169A
SPRING
COIL F/L(R) - D37
114
4260R-0052A
ARM
DECK/MECHA F/L (R) OTHER - D37
011
4261R-0040A
ARM ASSEMBLY
DECK/MECHA TENSION - D37
017
4408R-0005A
REEL
DECK/MECHA S OTHER - D37
017
4408R-0005B
REEL
DECK/MECHA S (VE) OTHER - D37
021
4421R-M002A
BRAKE ASSEMBLY
T - D37
024
4261R-0042A
ARM ASSEMBLY
DECK/MECHA IDLER(N) - D37
027
4470R-0133A
GEAR
DECK/MECHA WHEEL OTHER - D37
028
4408R-0006A
REEL
DECK/MECHA T OTHER - D37
051
4400R-0005A
BELT
CAPSTAN
055
4470R-0140A
GEAR
DECK/MECHA DRIVE OTHER - D37
056
4470R-0139A
GEAR
DECK/MECHA CAM OTHER - D37
058
4421R-M001A
BRAKE ASSEMBLY
CAPSTAN -D37
061
4265R-0007A
CLUTCH ASSEMBLY
DECK/MECHA D37(N)
DECK/MECHA SECTOR OTHER - D37
REMARKS
ALTERNATE
ALTERNATE
064
4470R-0141A
GEAR
A12
4471R-0015A
GEAR ASSEMBLY
DECK/MECHA P2 - D37
068
4470R-0134A
GEAR
DECK/MECHA P2 OTHER - D37
NSP
069
4970R-0122A
SPRING
COIL D35
NSP
NSP
070
4261R-0043A
ARM ASSEMBLY
DECK/MECHA P2 - D37
A22
4471R-0016A
GEAR ASSEMBLY
DECK/MECHA RACK F/L - D37
054
4470R-0136A
GEAR
DECK/MECHA RACK F/L OTHER - D3
054A
4970R-0171A
SPRING
COIL RACK F/L - D37
A11
4471R-0017A
GEAR ASSEMBLY
DECK/MECHA P3 - D37
065
4261R-0044A
ARM ASSEMBLY
DECK/MECHA P3 - D37
NSP
066
4970R-0122A
SPRING
COIL D35
NSP
NSP
067
4470R-0135A
GEAR
DECK/MECHA P3 OTHER - D37
060
4510R-0065A
LEVER
DECK/MECHA F/R OTHER - D37
076
4510R-0063A
LEVER
DECK/MECHA SPRING OTHER - D37
078
4510R-0062A
LEVER
DECK/MECHA TENSION OTHER - D37
DECK/MECHA BRAKE OTHER - D37
080
4510R-0064A
LEVER
A24
4511R-0005A
LEVER ASSEMBLY
SWITCH(C) - D37
115
4510R-0070A
LEVER
DECK/MECHA SWITCH(C) OTHER - D
116
4970R-0163A
SPRING
COIL D35S SWITCH
003
4930R-0449A
HOLDER
DECK/MECHA FPCB(6CH) - D37C MO
026
4681RF0039A
MOTOR ASSEMBLY
DECK/MECHA L/D - (DI) D37
NSP
026
4681RF0039C
MOTOR ASSEMBLY
DECK/MECHA L/D - (DI) D37
NSP
052
4680R-A015A
MOTOR(MECH)
CAPSTAN F2QVB66 SANKYO FOR D37
052
4680R-A016A
MOTOR(MECH)
CAPSTAN MCVC-037AA LGIT FOR D3
ALTERNATE
052
4680R-A017A
MOTOR(MECH)
CAPSTAN DMVCMC20L SAMSUNG FOR
ALTERNATE
052
4680R-A016B
MOTOR(MECH)
CAPSTAN MCVC-037AB LGIT LB1189
ALTERNATE
A21
4931R-0084A
HOLDER ASSEMBLY
DECK/MECHA CST - D37
102
4970R-0173A
SPRING
COIL STOPPER - D37
103
4930R-0452A
HOLDER
DECK/MECHA SIDE (L) OTHER - D3
NSP
105
4930R-0450A
HOLDER
DECK/MECHA CST OTHER - D37
NSP
106
4930R-0451A
HOLDER
DECK/MECHA SIDE(R) OTHER - D37
NSP
5 - 2
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
107
4510R-0061A
LEVER
DECK/MECHA STOPPER OTHER - D37
004
5006R-0045A
CAP
DECK/MECHA FPCB - D37C MOLD
008
6850R-HG18Y
CABLE,FLAT
P=1.25 FFC UL2896(0.05X0.8) 7
015
5870R-0007A
OPENER
DECK/MECHA LID OTHER - D37
022
6520D00004B
HEAD(CIRC)
ST ST FE HEAD FOR D37 13.5
022
6520D00006A
HEAD(CIRC)
HVFHP0055A ALPS FE HEAD FOR CO
031
4970R-0175A
SPRING
COIL TENSION - D37
052A
4980R-0029A
SUPPORTER
DECK/MECHA CAPSTAN OTHER - D37
109
5870R-0008A
OPENER
DECK/MECHA DOOR OTHER - D37
A01
6723R-0603E
DRUM(CIRC) ASSEMBLY
DECK/MECHA (9C6S) D37-6CH NTSC
REMARKS
NSP
ALTERNATE
*** CHASSIS ASSEMBLY ***
A44
3141R-V032K
CHASSIS ASSEMBLY
2006 COMBI LG MODEL M,A,B OPT.
260
3210R-V011A
FRAME
ONE BOARD MOLD HIPS 403AF BK
261
5040R-0069S
RUBBER
CCD 05 NEW SILICON OTHER 2T (3
330
3140R-V010M
CHASSIS
V10S 2006 COMBI PRESS RCA W/O
452
1SZZR-0098A
SCREW,DRAWING
+ 2 D3.0 L10.0 MSWR3/FZMCY-1 3
NSP
*** PWB(PCB) ASSEMBLY,TOTAL ***
A47
6871R-4927B
PWB(PCB) ASSEMBLY,TOTAL
2006 COMBI ZORAN WITH DIVX NT
288
4930R-0573A
HOLDER
VCR V9500 MOLD POWER PWB
BC101
636-004C
FILTER(CIRC),EMC
BEAD CORE BFS3550R2FD8,R T/P
BD101
0DD160000DA
DIODE,RECTIFIERS
S1WBA60 BK SHINDENGEN - 600V -
BD101
0DRRE00060A
DIODE,RECTIFIERS
DB105-C-S-V50 RECTRON BK NON 6
624-088L
CAPACITOR,DRAWING
435D SUNIL ELECTRONICS 0.1UF/2
C101
624-088N
CAPACITOR,DRAWING
MPX104K 275VAC BULK ETR
ALTERNATE
C101
624-088F
CAPACITOR,DRAWING
PCX2 275V 0.1UF,M (PILKO)
ALTERNATE
C102
624-088L
CAPACITOR,DRAWING
435D SUNIL ELECTRONICS 0.1UF/2
C102
624-088F
CAPACITOR,DRAWING
PCX2 275V 0.1UF,M (PILKO)
ALTERNATE
C102
624-088N
CAPACITOR,DRAWING
MPX104K 275VAC BULK ETR
ALTERNATE
C103
0CE1570R610
CAPACITOR,FIXED ELECTROLYTIC
150UF SHL 250V 20% BULK FL
C104
0CN1040K948
CAPACITOR,FIXED TUBULAR(HIGH D
0.1UF D 50V 80%,-20% F(Y5V) TA
C105
0CQ1031Y519
CAPACITOR,FIXED FILM
0.01UF D 630V 10% PE NI TP5
C101
C106
624-087G
CAPACITOR,FIXED CERAMIC(HIGH D
HIGH-VOL 68PF/1KV SMPS SAMHWA
C107
0CN1030K518
CAPACITOR,TUBULAR(HIGH DIELEC)
0.01UF 50V K B TA26
C108
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C109
0CE3366H638
CAPACITOR,FIXED ELECTROLYTIC
33UF SMS,SG 25V 20% FM5 TP 5
C110
0CG1020U630
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF D 400V 20% E(Z5U) R
C111
0CG1020U630
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF D 400V 20% E(Z5U) R
C115
0CN1040K948
CAPACITOR,FIXED TUBULAR(HIGH D
0.1UF D 50V 80%,-20% F(Y5V) TA
C121
624-087D
CAPACITOR,FIXED CERAMIC(HIGH D
HI-VOL 470P/1KVDC SMPS SAMHWA
470UF KME TYPE 25V 20% FM5 BUL
C124
0CE477BH630
CAPACITOR,FIXED ELECTROLYTIC
C126
624-085D
CAPACITOR,FIXED ELECTROLYTIC
CE 47UF/50V KME (SMPS)
C127
0CE108BF630
CAPACITOR,FIXED ELECTROLYTIC
1000UF KME TYPE 16V 20% FM5 BU
2200UF KME TYPE 16V 20% FM5 BU
C128
0CE228BF630
CAPACITOR,FIXED ELECTROLYTIC
C134
0CE227CH618
CAPACITOR,FIXED ELECTROLYTIC
220UF SHL,SD 25V 20% FL TP 5
C137
0CE3376D638
CAPACITOR,FIXED ELECTROLYTIC
330UF SMS,SG 10V 20% FM5 TP 5
C138
624-082H
CAPACITOR,FIXED ELECTROLYTIC
CE 1000UF/10V SHL(10*12.5)T/P
C143
0CQ1042K409
CAPACITOR,FIXED FILM
0.1UF S 50V 5% PE TP5
C159
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C160
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C161
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C162
0CE4776D638
CAPACITOR,FIXED ELECTROLYTIC
470UF SMS,SG 10V 20% FM5 TP 5
C164
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C166
0CN223AK948
CAPACITOR,TUBULAR(HIGH DIELEC)
0.022UF 50V Z F TA26 S
D101
0DD221009AA
DIODE,RECTIFIERS
ERA22-10 KFLB,TP ,R T/P,FUJI
D102
0DR104009BA
DIODE,RECTIFIERS
RL104F TP RECTRON - 400V 1A 30
D102
0DRGF00239A
DIODE,RECTIFIERS
FR104E GULF TP NON 400V 1A 30A
D121
0DR104009BA
DIODE,RECTIFIERS
RL104F TP RECTRON - 400V 1A 30
5 - 3
ALTERNATE
ALTERNATE
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
D121
0DRGF00239A
DIODE,RECTIFIERS
FR104E GULF TP NON 400V 1A 30A
REMARKS
D123
0DR810040BA
DIODE,RECTIFIERS
ERC81-004L22 BK FUJI DO201AD 4
D123
0DR158220AA
DIODE,RECTIFIERS
1N5822 BK RECTRON DO201AD 40V
ALTERNATE
D123
0DRGF00210A
DIODE,RECTIFIERS
1N5822 GULF BK DO201AD 40V 3A
ALTERNATE
D124
0DSGF00040A
DIODE,SWITCHING
UF5402-M11 GULF BK DO201AD 200
D124
0DSDI00110A
DIODE,SWITCHING
UF3003 DIODES BK DO201AD 200V
D125
0DSDI00090A
DIODE,SWITCHING
SB360 DIODES BK DO201AD 60V 3A
1SS133 TP ROHM KOREA - - - - -
ALTERNATE
ALTERNATE
D127
0DD133009AA
DIODE,SWITCHING
FR101
0RM0221K634
RESISTOR,FIXED CEMENT
2.2 OHM 2 W 5% MF15 MPR
IC101
0IPMGIH005A
IC,POWER MANAGEMENT
ICE3B0565 INFINEON 8PIN,DIP ST
IC102
657-063A
SENSOR
LTV-817B,PHOTO COUPLER(LITEON)
IC102
6500RDB010A
SENSOR,PHOTO
PC123YN2J00F SHARP PHOTOCOUPLE
ALTERNATE
IC102
6500RDB011B
SENSOR
K1010B COSMO 4PIN PHOTOCOUPLER
ALTERNATE
IC103
0IKE431000A
IC,LINEAR
KIA431 3 PIN TP - -
IC103
0ISS431000A
IC,LINEAR
KA431AZ (LM431AZ) - - - -
L102
616-145G
FILTER(CIRC),DRAWING
SHT LFSQ2215V4-04220
L102
616-145E
FILTER(CIRC),DRAWING
KSE-145E KSE LINE FILTER SQ211
L124
633-088G
COIL,CHOKE
22MH TOKO 5MM TP
L124
6140R-C011A
COIL,RF
CHOKE COIL TDK 22UH(=633-088G
L127
633-088G
COIL,CHOKE
22MH TOKO 5MM TP
L127
6140R-C011A
COIL,RF
CHOKE COIL TDK 22UH(=633-088G
L128
6140RCC003H
COIL,RF
CHOKE COIL 22 UH 8X8 5 PIE SAM
PPM01
6630R-BF03M
CONNECTOR (CIRC),BOARD TO BOAR
JE121-13 JAE EUN 13P 2.54MM
PW101
561-292B
CONNECTOR(CIRC),DRAWING
GP390 LGC 3P 3.96 STRAIGHT SN
Q161
0TR126809BA
TRANSISTOR,BIPOLARS
KTA1268-BL TP KEC - -
Q162
0TR319809AC
TRANSISTOR,BIPOLARS
KTC3198 TP KEC - - -BL (KTC181
Q162
0TR534309BA
TRANSISTOR,BIPOLARS
2SC5343-L TP AUK TO92 -
Q163
0TR127309AA
TRANSISTOR,BIPOLARS
KTA1273 TP KEC TO92 -Y(KTA966A
ALTERNATE
ALTERNATE
ALTERNATE
ALTERNATE
ALTERNATE
Q163
0TR928009AD
TRANSISTOR,BIPOLARS
KSA928A-Y,TO-92L TP SAMSUNG TO
ALTERNATE
Q163
0TR127709AB
TRANSISTOR,BIPOLARS
AUK KOREA STB1277LY-AT TP TO-9
ALTERNATE
Q164
0TR534309BA
TRANSISTOR,BIPOLARS
2SC5343-L TP AUK TO92 -
Q164
0TR534409AA
TRANSISTOR,BIPOLARS
2SC5344Y TP AUK - -
Q165
0TR127309AA
TRANSISTOR,BIPOLARS
KTA1273 TP KEC TO92 -Y(KTA966A
Q165
0TR127709AB
TRANSISTOR,BIPOLARS
AUK KOREA STB1277LY-AT TP TO-9
ALTERNATE
Q165
0TR928009AD
TRANSISTOR,BIPOLARS
KSA928A-Y,TO-92L TP SAMSUNG TO
ALTERNATE
Q166
0TR320509AB
TRANSISTOR,BIPOLARS
KTC3205-Y(KTC2236A) TP KEC TO9
ALTERNATE
Q166
0TR232809AB
TRANSISTOR,BIPOLARS
KSC2328A-Y TP SAMSUNG TO-92L -
ALTERNATE
Q166
0TR186209AB
TRANSISTOR,BIPOLARS
AUK KOREA STD1862LY-AT TP TO-9
ALTERNATE
R100
0RD1504H632
RESISTOR,FIXED CARBON FILM
1.5M OHM 1/2 W 5.00% MF10
R104
0RS5602K619
RESISTOR,FIXED METAL OXIDE FIL
56K OHM 2 W 5.00% TR
R105
0RD0102F608
RESISTOR,FIXED CARBON FILM
10 OHM 1/6 W 5% TA26
R109
0RS0750K619
RESISTOR,FIXED METAL OXIDE FIL
0.75 OHM 2 W 5.00% TR
R136
0RD1003F608
RESISTOR,FIXED CARBON FILM
100K OHM 1/6 W 5% TA26
R141
0RD2200F608
RESISTOR,FIXED CARBON FILM
220 OHM 1/6 W 5% TA26
R142
0RD2201F608
RESISTOR,FIXED CARBON FILM
2.2K OHM 1/6 W 5% TA26
R143
0RD1001F608
RESISTOR,FIXED CARBON FILM
1K OHM 1/6 W 5% TA26
R144
0RN3301F408
RESISTOR,FIXED METAL FILM
3.3K OHM 1/6 W 1% TA26
R145
0RN2701F408
RESISTOR,FIXED METAL FILM
2.7K OHM 1/6 W 1% TA26
R146
0RD2700F608
RESISTOR,FIXED CARBON FILM
270 OHM 1/6 W 5% TA26
R154
0RD1001F608
RESISTOR,FIXED CARBON FILM
1K OHM 1/6 W 5% TA26
R155
0RD1802F608
RESISTOR,FIXED CARBON FILM
18K OHM 1/6 W 5% TA26
R156
0RD1001F608
RESISTOR,FIXED CARBON FILM
1K OHM 1/6 W 5% TA26
R157
0RD3300F608
RESISTOR,FIXED CARBON FILM
330 OHM 1/6 W 5% TA26
R163
0RD4701F608
RESISTOR,FIXED CARBON FILM
4.7K OHM 1/6 W 5% TA26
R164
0RD4701F608
RESISTOR,FIXED CARBON FILM
4.7K OHM 1/6 W 5% TA26
R166
0RD5601F608
RESISTOR,FIXED CARBON FILM
5.6K OHM 1/6 W 5% TA26
R168
0RD5601F608
RESISTOR,FIXED CARBON FILM
5.6K OHM 1/6 W 5% TA26
5 - 4
S AL LOCA. NO. PART NO.
R172
0RD1001F608
DESCRIPTION
SPECIFICATION
RESISTOR,FIXED CARBON FILM
1K OHM 1/6 W 5% TA26
R174
0RD3300F608
RESISTOR,FIXED CARBON FILM
330 OHM 1/6 W 5% TA26
T101
6170RNGW12P
TRANSFORMER,SMPS[COIL]
EER2828 15 PIN SOOJUNG,SAMWHA
V101
SVC681D-10A SAMHWA 4.O CUT
656-004C
VARISTOR,DRAWING
ZD102
0DZ202609AA
DIODE,ZENERS
UZ-20BSB 26MM TP PYUNG CHANG D
ZD103
0DZ622609BB
DIODE,ZENERS
UZ-6.2BSB 26MM TP PYUNG CHANG
ZD151
0DZ132609AB
DIODE,ZENERS
GDZJ13A 26MM TP GRANDE DO34 0
ZD151
0DZ132609BB
DIODE,ZENERS
UZ-13BSA 26MM TP PYUNG CHANG
ZD152
0DZ102609BB
DIODE,ZENERS
UZ-10BSB 26MM TP PYUNG CHANG D
ZD152
0DZ100009HA
DIODE,ZENERS
UZ-10BM TP PYUNG CHANG - 0.5W
REMARKS
ALTERNATE
ALTERNATE
*** BOARD ASSEMBLY ***
A46
3501R-9310D
BOARD ASSEMBLY
322
3110R-V013A
CASE
VCR V1310MZ.NA1ULZ MAIN BOARD
SHIELD(SLIM-COMBI) PRESS .
323
3111R-0089E
CASE ASSEMBLY
PRE AMP SLIM COMBI C-CORE A NO
324
4930R-0472A
HOLDER
VCR ONE BOARD SLIM MOLD HIPS 6
IC604A
6957R-931AB
PROGRAM
COMBI-P NTSC 2006 ZV1002020010
CN201
6630R-FB10W
CONNECTOR (CIRC),FFC/FPC
00-6232-023-006-800 ELCO 23PIN
CN202
6630R-FB109
CONNECTOR (CIRC),FFC/FPC
00-6232-009-006-800 ELCO 9P 1-
CN702
6630B60E913
CONNECTOR (CIRC),BOARD TO BOAR
JE117-D22T-13 JAE EUN 13P 2.54
IC301
0ILNRHI009B
IC,LINEAR
HA118725ANF-E PB-FREE HITACHI
IC301
0ILNRHI009A
IC,LINEAR
HA118725NF HITACHI 100PIN QFP
JK901
6612J00049A
JACK,RCA
RCA-1205A-01-01 YUQIU 2004 COM
JK904
6612B00011A
JACK,DIN
DIN405 YUQIU 2004 COMBI
P3D01
561-234S
CONNECTOR (CIRC),FFC/FPC
GF120-9S-TS-A LG CABLE 9P 1.25
P3D02
6630R5S008J
CONNECTOR(CIRC),DRAWING
06(11)FM22.5H-BTR-SH (LF)(SN)
P3D03
561-251B
CONNECTOR(CIRC),DRAWING
GB201-2P-TS-B(LGC)
TU701
6700NFNL05A
TUNER
TADM-H202F(US.LGIT) LG INOTEK
X601
6212AA2271F
RESONATOR,CRYSTAL
HC-49S KITELCO 27MHZ +/- 20 PP
C201
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C208
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C209
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C214
0CE4773C630
CAPACITOR,FIXED ELECTROLYTIC
470UF SRE,SE 6.3V 20% FM5 BULK
C216
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C217
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C223
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C301
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C303
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C305
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C308
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C309
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
C310
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
C313
0CQ2231N409
CAPACITOR,FIXED FILM
0.022UF D 100V 5% PE TP5
C314
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C317
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C319
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C325
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C327
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
C328
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C337
0CE1063F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRE,SE 16V 20% FM5 TP 5
C339
0CE3354K638
CAPACITOR,FIXED ELECTROLYTIC
3.3UF SRA,SS 50V 20% FM5 TP 5
C340
0CE1063F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRE,SE 16V 20% FM5 TP 5
C343
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C348
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C349
0CC0500K015
CAPACITOR,FIXED CERAMIC(TEMP.C
5PF D 50V O.25 PF NP0 TR
C350
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C353
0CE3354K638
CAPACITOR,FIXED ELECTROLYTIC
3.3UF SRA,SS 50V 20% FM5 TP 5
C355
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
5 - 5
ALTERNATE
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C359
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C366
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C3A1
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C402
0CE4775C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SR,SV 6.3V 20% FM5 TP 5
C405
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C406
0CE2263F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRE,SE 16V 20% FM5 TP 5
C407
0CE1074F638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 16V 20% FM5 TP 5
C408
0CE2263F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRE,SE 16V 20% FM5 TP 5
C413
0CE1074F638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 16V 20% FM5 TP 5
C414
0CE2263F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRE,SE 16V 20% FM5 TP 5
C415
0CE2263F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRE,SE 16V 20% FM5 TP 5
C416
0CQ3921N409
CAPACITOR,FIXED FILM
0.0039UF D 100V 5% PE TP5
C417
0CQ3921N409
CAPACITOR,FIXED FILM
0.0039UF D 100V 5% PE TP5
C500
0CE4775C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SR,SV 6.3V 20% FM5 TP 5
C503
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C516
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C531
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C534
0CE4754H638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 25V 20% FM5 TP 5
C535
0CE4754H638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 25V 20% FM5 TP 5
C546
0CE4764H638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 25V 20% FM5 TP 5
C561
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C578
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C579
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C584
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C586
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C592
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C5G1
0CE1086C638
CAPACITOR,FIXED ELECTROLYTIC
1000000000PF SMS,SG 6.3V 20% F
C612
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C614
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C616
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C618
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C642
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C643
0CE4764C638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 6.3V 20% FM5 TP 5
C673
0CE4764F638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 16V 20% FM5 TP 5
C6A7
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C6C9
0CE2274C638
CAPACITOR,FIXED ELECTROLYTIC
220UF SRA,SS 6.3V 20% FM5 TP 5
C701
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C702
0CE4774C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SRA,SS 6.3V 20% FM5 TP 5
C712
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C801
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C806
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C807
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C808
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C816
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
C826
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C828
0CE4764F638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 16V 20% FM5 TP 5
C829
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
C830
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C831
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C833
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
C839
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C840
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C843
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
C846
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C847
0CE1064F638
CAPACITOR,FIXED ELECTROLYTIC
10UF SRA,SS 16V 20% FM5 TP 5
C851
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C358
5 - 6
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
C866
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
C871
0CE4753K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRE,SE 50V 20% FM5 TAPPI
C873
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
C876
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C877
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C879
0CE2254K638
CAPACITOR,FIXED ELECTROLYTIC
2.2UF SRA,SS 50V 20% FM5 TP 5
C880
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C881
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C882
0CE4764F638
CAPACITOR,FIXED ELECTROLYTIC
47UF SRA,SS 16V 20% FM5 TP 5
C883
0CE1054K638
CAPACITOR,FIXED ELECTROLYTIC
1UF SRA,SS 50V 20% FM5 TP 5
C886
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C887
0CE3354K638
CAPACITOR,FIXED ELECTROLYTIC
3.3UF SRA,SS 50V 20% FM5 TP 5
C888
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C889
0CE4754K638
CAPACITOR,FIXED ELECTROLYTIC
4.7UF SRA,SS 50V 20% FM5 TP 5
C902
0CE4774C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SRA,SS 6.3V 20% FM5 TP 5
C903
0CE1085C638
CAPACITOR,FIXED ELECTROLYTIC
1000UF SR,SV 6.3V 20% FM5 TP 5
C904
0CE4774C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SRA,SS 6.3V 20% FM5 TP 5
C908
0CE1085C638
CAPACITOR,FIXED ELECTROLYTIC
1000UF SR,SV 6.3V 20% FM5 TP 5
C910
0CE1074C638
CAPACITOR,FIXED ELECTROLYTIC
100UF SRA,SS 6.3V 20% FM5 TP 5
C911
0CE4774C638
CAPACITOR,FIXED ELECTROLYTIC
470UF SRA,SS 6.3V 20% FM5 TP 5
C913
0CE2264F638
CAPACITOR,FIXED ELECTROLYTIC
22UF SRA,SS 16V 20% FM5 TP 5
D201
0DR104009AB
DIODE,RECTIFIERS
RL104 R. TP GULF SEMICONDUCTOR
D802
0DD133009AA
DIODE,SWITCHING
1SS133 TP ROHM KOREA - - - - -
IC504
0IKE703100A
IC,LINEAR
KIA7031P 3P 3.1V RESET(TAPING)
IC505
0IKE704200B
IC,POWER MANAGEMENT
KIA7042P(AT) TO-92 4.2V RESET
L300
0LR0332K035
INDUCTOR,RADIAL LEAD
33UH 10% TP 6 X 6 TR5 -
L301
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L302
0LR1000K035
INDUCTOR,RADIAL LEAD
100UH 10% TP 6 X 6 TR5 -
L303
0LA1200K018
INDUCTOR,AXIAL LEAD
120UH 10% TP 2.3 X 3.4 TA26 -
L304
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L306
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L307
0LA0122K018
INDUCTOR,AXIAL LEAD
12UH 10% TP 2.3 X 3.4 TA26 -
L308
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L311
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L501
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L511
0LA0221K018
INDUCTOR,AXIAL LEAD
2.2UH 10% TP 2.3 X 3.4 TA26 -
REMARKS
L512
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L5F1
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
L5F2
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
L5G1
0LR4700K035
INDUCTOR,RADIAL LEAD
470UH 10% TP 6 X 6 TR5 -
L701
0LR0102K035
INDUCTOR,RADIAL LEAD
10UH 10% TP 6 X 6 TR5 -
L822
0LR1000J0N5
INDUCTOR,RADIAL LEAD
100UH 5% TP 3X5 TR5 -
L906
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
L907
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
L908
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
L909
0LA0102K018
INDUCTOR,AXIAL LEAD
10UH 10% TP 2.3 X 3.4 TA26 -
Q301
0TR534409AA
TRANSISTOR,BIPOLARS
2SC5344Y TP AUK - -
Q301
0TR320309AA
TRANSISTOR,BIPOLARS
KTC3203 KEC TP TO92 50V 150MA
Q302
0TR928009AD
TRANSISTOR,BIPOLARS
KSA928A-Y,TO-92L TP SAMSUNG TO
Q302
0TR127709AB
TRANSISTOR,BIPOLARS
AUK KOREA STB1277LY-AT TP TO-9
ALTERNATE
Q302
0TR127309AA
TRANSISTOR,BIPOLARS
KTA1273 TP KEC TO92 -Y(KTA966A
ALTERNATE
Q503
0TR928009AD
TRANSISTOR,BIPOLARS
KSA928A-Y,TO-92L TP SAMSUNG TO
Q503
0TR127709AB
TRANSISTOR,BIPOLARS
AUK KOREA STB1277LY-AT TP TO-9
ALTERNATE
Q503
0TR127309AA
TRANSISTOR,BIPOLARS
KTA1273 TP KEC TO92 -Y(KTA966A
ALTERNATE
Q701
0TR534409AA
TRANSISTOR,BIPOLARS
2SC5344Y TP AUK - -
SW501
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW501
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
5 - 7
ALTERNATE
ALTERNATE
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
SW501
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
REMARKS
SW502
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW502
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
ALTERNATE
SW502
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
ALTERNATE
SW503
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
ALTERNATE
SW503
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
ALTERNATE
SW503
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
ALTERNATE
SW504
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW504
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
ALTERNATE
SW504
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
ALTERNATE
SW505
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW505
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
ALTERNATE
SW505
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
ALTERNATE
SW506
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW506
6600RRT001R
SWITCH,TACT
SKHVBG3910-AA FORWARD 12V DC 5
ALTERNATE
SW506
6600RRT001G
SWITCH,TACT
EVQ 213 09K MATSUSHITA 15V DC
ALTERNATE
X502
6212AA2148F
RESONATOR,CRYSTAL
HC-49S KITELCO 14.31818MHZ +/-
ZD701
0DZ622609AB
DIODE,ZENERS
UZ-6.2BSA 26MM TP PYUNG CHANG
C202
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C203
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C204
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C205
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C206
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C207
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C210
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C211
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C212
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C213
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C219
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C220
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C224
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C225
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C302
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C304
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C306
0CH1222K562
CAPACITOR,FIXED CERAMIC(TEMP.C
2200PF 50V 10% X7R(X) 1608 R/T
C307
0CH1152K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1500PF 50V 10% B(5YP) 1608 R/T
C311
0CH4151K412
CAPACITOR,FIXED CERAMIC(HIGH D
150PF 50V 5% NP0 1608 R/TP
C312
0CH1561K462
CAPACITOR,FIXED CERAMIC(TEMP.C
560PF 50V 5% X7R(X) 1608 R/TP
C320
0CH4151K412
CAPACITOR,FIXED CERAMIC(HIGH D
150PF 50V 5% NP0 1608 R/TP
C321
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C322
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C323
0CH4470K412
CAPACITOR,FIXED CERAMIC(HIGH D
47PF 50V 5% NP0 1608 R/TP
C324
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C326
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C329
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C330
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C331
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C332
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C335
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C336
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C338
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C341
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C342
0CH4331K412
CAPACITOR,FIXED CERAMIC(HIGH D
330PF 50V 5% NP0 1608 R/TP
C344
0CH1473H942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.047UF 25V 80%,-20% Y5V(F) 16
C346
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C347
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C351
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
5 - 8
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
C352
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C354
0CH1472K562
CAPACITOR,FIXED CERAMIC(TEMP.C
4700PF 50V 10% X7R(X) 1608 R/T
C356
0CH1333K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.033UF 50V 10% X7R(X) 1608 R/
C357
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C360
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C362
0CH4270K412
CAPACITOR,FIXED CERAMIC(HIGH D
27PF 50V 5% NP0 1608 R/TP
C365
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C367
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C368
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C369
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C370
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C371
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C374
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C376
0CH4181K412
CAPACITOR,FIXED CERAMIC(HIGH D
180PF 50V 5% NP0 1608 R/TP
C377
0CH4151K412
CAPACITOR,FIXED CERAMIC(HIGH D
150PF 50V 5% NP0 1608 R/TP
C401
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C409
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C410
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C411
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C412
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C418
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C501
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C502
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C505
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C508
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C510
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C511
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C514
0CH4240K412
CAPACITOR,FIXED CERAMIC(HIGH D
24PF 50V 5% NP0 1608 R/TP
C515
0CH4240K412
CAPACITOR,FIXED CERAMIC(HIGH D
24PF 50V 5% NP0 1608 R/TP
C520
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C525
0CH1104K512
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 10% B(5YP) 1608 R/TP
C542
0CH4681K412
CAPACITOR,FIXED CERAMIC(HIGH D
680PF 50V 5% NP0 1608 R/TP
C543
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C544
0CH1473H942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.047UF 25V 80%,-20% Y5V(F) 16
C545
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C551
0CH1333K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.033UF 50V 10% X7R(X) 1608 R/
C552
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C566
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C567
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C568
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C569
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C570
0CH4180K412
CAPACITOR,FIXED CERAMIC(HIGH D
18PF 50V 5% NP0 1608 R/TP
C571
0CH4200K412
CAPACITOR,FIXED CERAMIC(HIGH D
20PF 50V 5% NP0 1608 R/TP
C572
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C573
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C574
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C577
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C580
0CH1223K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 50V 80%,-20% Y5V(F) 16
C581
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C582
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C583
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C585
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C588
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C589
0CH4221K412
CAPACITOR,FIXED CERAMIC(HIGH D
220PF 50V 5% NP0 1608 R/TP
C590
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C593
0CH4471K412
CAPACITOR,FIXED CERAMIC(HIGH D
470PF 50V 5% NP0 1608 R/TP
C594
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
5 - 9
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
C595
0CH4120K412
CAPACITOR,FIXED CERAMIC(HIGH D
12PF 50V 5% NP0 1608 R/TP
C596
0CH4120K412
CAPACITOR,FIXED CERAMIC(HIGH D
12PF 50V 5% NP0 1608 R/TP
C597
0CH4681K412
CAPACITOR,FIXED CERAMIC(HIGH D
680PF 50V 5% NP0 1608 R/TP
C598
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C5L2
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C5L3
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C602
0CH1273F562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.027UF 1608 16V 10% X7R R/TP
C604
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C605
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C606
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C607
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C608
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C609
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C610
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C611
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C613
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C615
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C617
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C619
0CH4180K412
CAPACITOR,FIXED CERAMIC(HIGH D
18PF 50V 5% NP0 1608 R/TP
C622
0CH4150K412
CAPACITOR,FIXED CERAMIC(HIGH D
15PF 50V 5% NP0 1608 R/TP
C623
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C624
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C626
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C627
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C628
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C629
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C631
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C632
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C633
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C634
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C635
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C636
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C637
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C638
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C639
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C640
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C641
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C644
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C648
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C649
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C650
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C651
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C652
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C657
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C660
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C662
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C664
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C674
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C675
0CH1223F512
CAPACITOR,FIXED CERAMIC(TEMP.C
0.022UF 16V 10% B(5YP) 1608 R/
C678
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C679
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C680
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C681
0CH4101K412
CAPACITOR,FIXED CERAMIC(HIGH D
100PF 50V 5% NP0 1608 R/TP
C683
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C684
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C692
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C693
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
5 - 10
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
C694
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C696
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C697
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C698
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C699
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C6A1
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
C6A6
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6A8
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C6C2
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6C3
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D1
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C6D2
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D3
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D4
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D5
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D6
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D7
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D8
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6D9
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6E3
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C6E5
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C6H1
0CH1102K562
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% X7R(X) 1608 R/T
C6H2
0CH1333K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.033UF 50V 10% X7R(X) 1608 R/
C6H3
0CH1333K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.033UF 50V 10% X7R(X) 1608 R/
C6H5
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C6H6
0CH4330K412
CAPACITOR,FIXED CERAMIC(HIGH D
33PF 50V 5% NP0 1608 R/TP
C6H7
0CH4080K112
CAPACITOR,FIXED CERAMIC(HIGH D
8PF 50V 0.5 PF NP0 1608 R/TP
C703
0CH1104K512
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 10% B(5YP) 1608 R/TP
C704
0CH1104K512
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 10% B(5YP) 1608 R/TP
C706
0CH4300K412
CAPACITOR,FIXED CERAMIC(HIGH D
30PF 50V 5% NP0 1608 R/TP
C707
0CH4300K412
CAPACITOR,FIXED CERAMIC(HIGH D
30PF 50V 5% NP0 1608 R/TP
C718
0CH4560K412
CAPACITOR,FIXED CERAMIC(HIGH D
56PF 50V 5% NP0 1608 R/TP
C821
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C822
0CH1222K562
CAPACITOR,FIXED CERAMIC(TEMP.C
2200PF 50V 10% X7R(X) 1608 R/T
C823
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C827
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C832
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C834
0CH1472K562
CAPACITOR,FIXED CERAMIC(TEMP.C
4700PF 50V 10% X7R(X) 1608 R/T
C836
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C838
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C841
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C844
0CH1472K562
CAPACITOR,FIXED CERAMIC(TEMP.C
4700PF 50V 10% X7R(X) 1608 R/T
C845
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C848
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C849
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C872
0CH4560K412
CAPACITOR,FIXED CERAMIC(HIGH D
56PF 50V 5% NP0 1608 R/TP
C874
0CH1105F942
CAPACITOR,FIXED CERAMIC(TEMP.C
1000000PF 16V 80%,-20% Y5V(F)
C875
0CH1333K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.033UF 50V 10% X7R(X) 1608 R/
C878
0CH4560K412
CAPACITOR,FIXED CERAMIC(HIGH D
56PF 50V 5% NP0 1608 R/TP
C884
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C885
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C914
0CH1103K562
CAPACITOR,FIXED CERAMIC(TEMP.C
0.01UF 50V 10% X7R(X) 1608 R/T
C918
0CH4151K412
CAPACITOR,FIXED CERAMIC(HIGH D
150PF 50V 5% NP0 1608 R/TP
C919
0CH4181K412
CAPACITOR,FIXED CERAMIC(HIGH D
180PF 50V 5% NP0 1608 R/TP
C921
0CH4151K412
CAPACITOR,FIXED CERAMIC(HIGH D
150PF 50V 5% NP0 1608 R/TP
C923
0CH4181K412
CAPACITOR,FIXED CERAMIC(HIGH D
180PF 50V 5% NP0 1608 R/TP
C925
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
5 - 11
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
C926
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C996
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
C9A1
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C9A3
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C9A5
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C9A7
0CH1102K512
CAPACITOR,FIXED CERAMIC(TEMP.C
1000PF 50V 10% B(5YP) 1608 R/T
C9B1
0CH1104K942
CAPACITOR,FIXED CERAMIC(TEMP.C
0.1UF 50V 80%,-20% Y5V(F) 1608
D401
0DSRM00118A
DIODE,SWITCHING
DAP202K T146 ROHM R/TP SMD 80V
IC201
0ILNR00091A
IC,LINEAR
AM5869S AMTEK HSOP28 REEL TAPI
IC401
0IPRPTI064A
IC,PERIPHERALS
PCM1753DBQR TEXAS INSTRUMENT 1
IC402
0ILNRUC001A
IC,LINEAR
MC4580 UTC 8PIN,SOP R/TP 2CH O
IC402
0ILNRAU017A
IC,LINEAR
S4580 AUK KOREA 8PIN,SOP R/TP
IC5F1
0ILNRPY001B
IC,LINEAR
PT6955 PTC 24PIN SOP R/TP LED
IC5F1
0IPRPG5001B
IC,PERIPHERALS
LG5-6955 LED DRIVER G-FIVE 24P
IC601
0ILNR00090A
IC,LINEAR
ZR36882ELCG ZORAN 208PIN,LQFP
REMARKS
ALTERNATE
ALTERNATE
IC603
0IMMREO001A
IC,MEMORIES
EM638165TS-7G ETRON 50PIN,TSOP
IC603
0IMMRHY001M
IC,MEMORIES
HY57V641620ETP-7,LF HYNIX 54P
ALTERNATE
IC603
0IMMREB004E
IC,MEMORIES
M12L64164A-7TG ESMT 54P TSOPII
ALTERNATE
IC605
0ISS240210A
IC,MEMORIES
S524A40X21-SCT0 SOP8 TP EEPROM
IC605
0IMMRSE002A
IC,MEMORIES
S-24CC02A-J8T1G SEIKO 8PIN,SOP
IC801
0ILNRSA013B
IC,LINEAR
LA72670BM-L-MPB-E SANYO 80PIN
IC901
0ILNR00048A
IC,LINEAR
MM1692XVBE MITSUMI 16PIN TSOP
J339
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
J602
0RH1100C622
RESISTOR,METAL GLAZED(CHIP)
110 OHM 1 / 16 W 1608 5.00% D
J603
0RH1100C622
RESISTOR,METAL GLAZED(CHIP)
110 OHM 1 / 16 W 1608 5.00% D
J604
0RH1100C622
RESISTOR,METAL GLAZED(CHIP)
110 OHM 1 / 16 W 1608 5.00% D
J901
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
J902
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
J903
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
J904
0RH0000D622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 10 W 2012 5.00% D
J905
0RH0000D622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 10 W 2012 5.00% D
L201
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
L202
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
L203
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
L205
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
L206
6200HJC102A
FILTER(CIRC),EMC
HB-1M2012-102JT CERATECH TP 3K
L310
0LCCE00004L
INDUCTOR,CHIP
1UH , CHIP2012 CERATECH R/TP
L601
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L602
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L603
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L604
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L605
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L607
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L609
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L610
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L6A3
0RH0000D622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 10 W 2012 5.00% D
L6A5
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L6A8
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L6A9
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
L6B2
6200S-JC01B
FILTER(CIRC),EMC
HB-1M2012-221JT CERATECH TP
Q201
0TR103709BB
TRANSISTOR,BIPOLARS
2SA1037K-Q CHIP TP ROHM - -
Q202
0TR103709BB
TRANSISTOR,BIPOLARS
2SA1037K-Q CHIP TP ROHM - -
Q203
0TRKE80068A
TRANSISTOR,BIPOLARS
KTA1531T-Y GRADE KEC R/TP TSM
Q204
0TRKE80068A
TRANSISTOR,BIPOLARS
KTA1531T-Y GRADE KEC R/TP TSM
Q206
0TR150409AC
TRANSISTOR,BIPOLARS
KTA1504 TP KEC - -GR-T1(ASG) C
Q303
0TR103009AA
TRANSISTOR,BIPOLARS
CHIP KRC103S-T1(NC)22-22 TP KE
Q305
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
5 - 12
ALTERNATE
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
Q306
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
Q307
0TR103009AC
TRANSISTOR,BIPOLARS
KRA103S-T1(PC)22-22 CHIP TP KE
Q403
0TR103009AC
TRANSISTOR,BIPOLARS
KRA103S-T1(PC)22-22 CHIP TP KE
Q404
0TR103009AC
TRANSISTOR,BIPOLARS
KRA103S-T1(PC)22-22 CHIP TP KE
Q405
0TR103709BB
TRANSISTOR,BIPOLARS
2SA1037K-Q CHIP TP ROHM - -
Q501
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
REMARKS
Q501
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q501
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
ALTERNATE
Q504
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
Q504
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
ALTERNATE
Q504
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q505
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
Q505
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
ALTERNATE
Q505
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q507
0TR150409AC
TRANSISTOR,BIPOLARS
KTA1504 TP KEC - -GR-T1(ASG) C
Q601
0TR390409DA
TRANSISTOR,BIPOLARS
2N3904S NPN SOT-23 TP KEC - -
Q602
0TR390409DA
TRANSISTOR,BIPOLARS
2N3904S NPN SOT-23 TP KEC - -
Q603
0TR390409DA
TRANSISTOR,BIPOLARS
2N3904S NPN SOT-23 TP KEC - -
Q805
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
Q805
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q805
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
ALTERNATE
Q901
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
Q901
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
ALTERNATE
Q901
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q902
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
Q902
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
ALTERNATE
Q902
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
Q924
0TR150409AC
TRANSISTOR,BIPOLARS
KTA1504 TP KEC - -GR-T1(ASG) C
Q930
0TR387509AC
TRANSISTOR,BIPOLARS
CHIP KTC3875S-GR-T1(ALG) TP KE
Q930
0TRON80009A
TRANSISTOR,BIPOLARS
BC846ALT1 ON SEMI(MOTOROLA) R/
ALTERNATE
Q930
0TRAU80017A
TRANSISTOR,BIPOLARS
2SC5343SG AUK KOREA R/TP SOT23
ALTERNATE
R201
0RJ4300C477
RESISTOR,METAL GLAZED(CHIP)
430 OHM 1/16 W 1% 1608 R/TP
R202
0RH1001C422
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 1.00% D
R203
0RH1201C422
RESISTOR,METAL GLAZED(CHIP)
1.2K OHM 1 / 16 W 1608 1.00% D
R204
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R205
0RH2001C622
RESISTOR,METAL GLAZED(CHIP)
2K OHM 1 / 16 W 1608 5.00% D
R206
0RH1000C422
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 1.00% D
R207
0RH1000C422
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 1.00% D
R208
0RH1501C622
RESISTOR,METAL GLAZED(CHIP)
1.5K OHM 1 / 16 W 1608 5.00% D
R209
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R211
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R212
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R213
0RH2202C622
RESISTOR,METAL GLAZED(CHIP)
22K OHM 1 / 16 W 1608 5.00% D
R214
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R216
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R217
0RH0331C622
RESISTOR,METAL GLAZED(CHIP)
3.3 OHM 1 / 16 W 1608 5.00% D
R218
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R219
0RH0471C622
RESISTOR,METAL GLAZED(CHIP)
4.7 OHM 1 / 16 W 1608 5.00% D
R220
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R221
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R222
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R226
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R262
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R263
0RH5601C622
RESISTOR,METAL GLAZED(CHIP)
5.6K OHM 1 / 16 W 1608 5.00% D
R270
0RH3302C622
RESISTOR,METAL GLAZED(CHIP)
33K OHM 1 / 16 W 1608 5.00% D
R301
0RH1202C622
RESISTOR,METAL GLAZED(CHIP)
12K OHM 1 / 16 W 1608 5.00% D
R302
0RH3303C622
RESISTOR,METAL GLAZED(CHIP)
330K OHM 1 / 16 W 1608 5.00% D
5 - 13
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
R303
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R304
0RH4702C622
RESISTOR,METAL GLAZED(CHIP)
47K OHM 1 / 16 W 1608 5.00% D
R305
0RH2202C622
RESISTOR,METAL GLAZED(CHIP)
22K OHM 1 / 16 W 1608 5.00% D
R306
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R307
0RH7501C622
RESISTOR,METAL GLAZED(CHIP)
7.5K OHM 1 / 16 W 1608 5.00% D
R308
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R309
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R310
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R311
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R312
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R313
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R315
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R316
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R317
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R319
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R320
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R322
0RH8202C622
RESISTOR,METAL GLAZED(CHIP)
82K OHM 1 / 16 W 1608 5.00% D
R323
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R324
0RH1501C622
RESISTOR,METAL GLAZED(CHIP)
1.5K OHM 1 / 16 W 1608 5.00% D
R325
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R326
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R328
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R332
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R333
0RH5601C622
RESISTOR,METAL GLAZED(CHIP)
5.6K OHM 1 / 16 W 1608 5.00% D
R337
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R338
0RH5601C622
RESISTOR,METAL GLAZED(CHIP)
5.6K OHM 1 / 16 W 1608 5.00% D
R339
0RJ6804C677
RESISTOR,METAL GLAZED(CHIP)
6.8M OHM 1/16 W 5% 1608 R/TP
R340
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R341
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R3J1
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R403
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R404
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R405
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R406
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R407
0RH5601C622
RESISTOR,METAL GLAZED(CHIP)
5.6K OHM 1 / 16 W 1608 5.00% D
R408
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R409
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R410
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R411
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R412
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R413
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R414
0RH3300C622
RESISTOR,METAL GLAZED(CHIP)
330 OHM 1 / 16 W 1608 5.00% D
R415
0RH3300C622
RESISTOR,METAL GLAZED(CHIP)
330 OHM 1 / 16 W 1608 5.00% D
R416
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R417
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R418
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R419
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R422
0RH0222C622
RESISTOR,METAL GLAZED(CHIP)
22 OHM 1 / 16 W 1608 5.00% D
R423
0RH0472C622
RESISTOR,METAL GLAZED(CHIP)
47 OHM 1 / 16 W 1608 5.00% D
R424
0RH0472C622
RESISTOR,METAL GLAZED(CHIP)
47 OHM 1 / 16 W 1608 5.00% D
R425
0RH0472C622
RESISTOR,METAL GLAZED(CHIP)
47 OHM 1 / 16 W 1608 5.00% D
R501
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R502
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R504
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R505
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R507
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R508
0RH2702C622
RESISTOR,METAL GLAZED(CHIP)
27K OHM 1 / 16 W 1608 5.00% D
5 - 14
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
R509
0RH5600C622
RESISTOR,METAL GLAZED(CHIP)
560 OHM 1 / 16 W 1608 5.00% D
R511
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R512
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R513
0RH3300C622
RESISTOR,METAL GLAZED(CHIP)
330 OHM 1 / 16 W 1608 5.00% D
R515
0RH2700C622
RESISTOR,METAL GLAZED(CHIP)
270 OHM 1 / 16 W 1608 5.00% D
R516
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R518
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R519
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R520
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R521
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R522
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R523
0RH5601C622
RESISTOR,METAL GLAZED(CHIP)
5.6K OHM 1 / 16 W 1608 5.00% D
R525
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R526
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R528
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R529
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R531
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R533
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R534
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R535
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R536
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R537
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R538
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R541
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R544
0RH1003C622
RESISTOR,METAL GLAZED(CHIP)
100K OHM 1 / 16 W 1608 5.00% D
R546
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R547
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R550
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R553
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R554
0RH1004C622
RESISTOR,METAL GLAZED(CHIP)
1M OHM 1 / 16 W 1608 5.00% D
R555
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R556
0RH2202C622
RESISTOR,METAL GLAZED(CHIP)
22K OHM 1 / 16 W 1608 5.00% D
R557
0RH2702C622
RESISTOR,METAL GLAZED(CHIP)
27K OHM 1 / 16 W 1608 5.00% D
R558
0RH2202C622
RESISTOR,METAL GLAZED(CHIP)
22K OHM 1 / 16 W 1608 5.00% D
R563
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R564
0RH2702C622
RESISTOR,METAL GLAZED(CHIP)
27K OHM 1 / 16 W 1608 5.00% D
R566
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R569
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R570
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R571
0RH2200C622
RESISTOR,METAL GLAZED(CHIP)
220 OHM 1 / 16 W 1608 5.00% D
R575
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R576
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R577
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R578
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R579
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R580
0RH1202C622
RESISTOR,METAL GLAZED(CHIP)
12K OHM 1 / 16 W 1608 5.00% D
R581
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R582
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R583
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R586
0RH1801C622
RESISTOR,METAL GLAZED(CHIP)
1.8K OHM 1 / 16 W 1608 5.00% D
R587
0RH1801C622
RESISTOR,METAL GLAZED(CHIP)
1.8K OHM 1 / 16 W 1608 5.00% D
R588
0RH3301C622
RESISTOR,METAL GLAZED(CHIP)
3.3K OHM 1 / 16 W 1608 5.00% D
R589
0RH1501C622
RESISTOR,METAL GLAZED(CHIP)
1.5K OHM 1 / 16 W 1608 5.00% D
R592
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R593
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R594
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R595
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
5 - 15
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
R596
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R597
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R598
0RH1201C622
RESISTOR,METAL GLAZED(CHIP)
1.2K OHM 1 / 16 W 1608 5.00% D
R599
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5C6
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5C7
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5D1
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R5D2
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5D3
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5D4
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5D5
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R5K1
0RH6800C622
RESISTOR,METAL GLAZED(CHIP)
680 OHM 1 / 16 W 1608 5.00% D
R5K2
0RH8200C622
RESISTOR,METAL GLAZED(CHIP)
820 OHM 1 / 16 W 1608 5.00% D
R5K3
0RH1201C622
RESISTOR,METAL GLAZED(CHIP)
1.2K OHM 1 / 16 W 1608 5.00% D
R5K4
0RH1501C622
RESISTOR,METAL GLAZED(CHIP)
1.5K OHM 1 / 16 W 1608 5.00% D
R5K5
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R5L1
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R601
0RH3902C622
RESISTOR,METAL GLAZED(CHIP)
39K OHM 1 / 16 W 1608 5.00% D
R602
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R604
0RH4302C622
RESISTOR,METAL GLAZED(CHIP)
43K OHM 1 / 16 W 1608 5.00% D
R605
0RH2002C422
RESISTOR,METAL GLAZED(CHIP)
20K OHM 1 / 16 W 1608 1.00% D
R606
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R607
0RH0912C622
RESISTOR,METAL GLAZED(CHIP)
91 OHM 1 / 16 W 1608 5.00% D
R608
0RH0912C622
RESISTOR,METAL GLAZED(CHIP)
91 OHM 1 / 16 W 1608 5.00% D
R609
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R610
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R611
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R612
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R613
0RJ3920C477
RESISTOR,METAL GLAZED(CHIP)
392 OHM 1/16 W 1% 1608 R/TP
R614
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R621
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R623
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R624
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R625
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R626
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R628
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R629
0LC11608D01
INDUCTOR,CHIP
HB-1M1608-121JT CERATECH R/TP
R629
0LCCE00003D
INDUCTOR,CHIP
HB-1M1608-121JT 120 OHM CERATE
R630
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R631
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R632
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R633
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R634
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R636
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R638
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R639
0RH2001C622
RESISTOR,METAL GLAZED(CHIP)
2K OHM 1 / 16 W 1608 5.00% D
R640
0RH2001C622
RESISTOR,METAL GLAZED(CHIP)
2K OHM 1 / 16 W 1608 5.00% D
R641
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R642
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R643
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R644
0RH7501C622
RESISTOR,METAL GLAZED(CHIP)
7.5K OHM 1 / 16 W 1608 5.00% D
R646
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R649
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R650
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R651
0RH3302C622
RESISTOR,METAL GLAZED(CHIP)
33K OHM 1 / 16 W 1608 5.00% D
R658
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R660
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
5 - 16
REMARKS
ALTERNATE
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
R661
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R670
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R671
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R682
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R683
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R684
0RH3301C622
RESISTOR,METAL GLAZED(CHIP)
3.3K OHM 1 / 16 W 1608 5.00% D
R685
0RH3301C622
RESISTOR,METAL GLAZED(CHIP)
3.3K OHM 1 / 16 W 1608 5.00% D
R686
0RH3301C622
RESISTOR,METAL GLAZED(CHIP)
3.3K OHM 1 / 16 W 1608 5.00% D
R687
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R688
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R690
0RH0752C422
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 1.00% D
R691
0RH1003C622
RESISTOR,METAL GLAZED(CHIP)
100K OHM 1 / 16 W 1608 5.00% D
R694
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R696
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R697
0RH0332C622
RESISTOR,METAL GLAZED(CHIP)
33 OHM 1 / 16 W 1608 5.00% D
R698
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R6A1
0RH1003C622
RESISTOR,METAL GLAZED(CHIP)
100K OHM 1 / 16 W 1608 5.00% D
R6A2
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
R702
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R706
0RH6800C622
RESISTOR,METAL GLAZED(CHIP)
680 OHM 1 / 16 W 1608 5.00% D
R707
0RH6800C622
RESISTOR,METAL GLAZED(CHIP)
680 OHM 1 / 16 W 1608 5.00% D
R708
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R711
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R714
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R801
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R802
0RH4702C622
RESISTOR,METAL GLAZED(CHIP)
47K OHM 1 / 16 W 1608 5.00% D
R804
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R805
0RH4702C622
RESISTOR,METAL GLAZED(CHIP)
47K OHM 1 / 16 W 1608 5.00% D
R806
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R807
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R808
0RH2201C622
RESISTOR,METAL GLAZED(CHIP)
2.2K OHM 1 / 16 W 1608 5.00% D
R809
0RH1800C622
RESISTOR,METAL GLAZED(CHIP)
180 OHM 1 / 16 W 1608 5.00% D
R810
0RH1801C622
RESISTOR,METAL GLAZED(CHIP)
1.8K OHM 1 / 16 W 1608 5.00% D
R811
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R812
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R813
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R814
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R817
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R818
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R821
0RH1002C622
RESISTOR,METAL GLAZED(CHIP)
10K OHM 1 / 16 W 1608 5.00% D
R822
0RH1003C622
RESISTOR,METAL GLAZED(CHIP)
100K OHM 1 / 16 W 1608 5.00% D
R823
0RH3002C622
RESISTOR,METAL GLAZED(CHIP)
30K OHM 1 / 16 W 1608 5.00% D
R836
0RH4700C622
RESISTOR,METAL GLAZED(CHIP)
470 OHM 1 / 16 W 1608 5.00% D
R838
0RH2701C622
RESISTOR,METAL GLAZED(CHIP)
2.7K OHM 1 / 16 W 1608 5.00% D
R839
0RH3902C622
RESISTOR,METAL GLAZED(CHIP)
39K OHM 1 / 16 W 1608 5.00% D
R842
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R843
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R844
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R845
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R851
0RH1000C622
RESISTOR,METAL GLAZED(CHIP)
100 OHM 1 / 16 W 1608 5.00% D
R856
0RH6801C622
RESISTOR,METAL GLAZED(CHIP)
6.8K OHM 1 / 16 W 1608 5.00% D
R857
0RH5602C622
RESISTOR,METAL GLAZED(CHIP)
56K OHM 1 / 16 W 1608 5.00% D
R858
0RH4702C622
RESISTOR,METAL GLAZED(CHIP)
47K OHM 1 / 16 W 1608 5.00% D
R866
0RH4702C622
RESISTOR,METAL GLAZED(CHIP)
47K OHM 1 / 16 W 1608 5.00% D
R867
0RH1502C622
RESISTOR,METAL GLAZED(CHIP)
15K OHM 1 / 16 W 1608 5.00% D
R874
0RH4701C622
RESISTOR,METAL GLAZED(CHIP)
4.7K OHM 1 / 16 W 1608 5.00% D
R8J1
0RH0000C622
RESISTOR,METAL GLAZED(CHIP)
0 OHM 1 / 16 W 1608 5.00% D
5 - 17
REMARKS
S AL LOCA. NO. PART NO.
DESCRIPTION
SPECIFICATION
R901
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R902
0RH8202C622
RESISTOR,METAL GLAZED(CHIP)
82K OHM 1 / 16 W 1608 5.00% D
R903
0RH8202C622
RESISTOR,METAL GLAZED(CHIP)
82K OHM 1 / 16 W 1608 5.00% D
R904
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R905
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R906
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R910
0RH2700C622
RESISTOR,METAL GLAZED(CHIP)
270 OHM 1 / 16 W 1608 5.00% D
R912
0RH2700C622
RESISTOR,METAL GLAZED(CHIP)
270 OHM 1 / 16 W 1608 5.00% D
R928
0RH1001C622
RESISTOR,METAL GLAZED(CHIP)
1K OHM 1 / 16 W 1608 5.00% D
R931
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R933
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R934
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R935
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
R936
0RH0752C622
RESISTOR,METAL GLAZED(CHIP)
75 OHM 1 / 16 W 1608 5.00% D
X301
6212AB2359C
RESONATOR,CRYSTAL
HC-49/SM BUBANG 3.579545MHZ +/
X301
6212AB2359E
RESONATOR,CRYSTAL
HC-49/SM CSC(SSANGTAI) 3.57954
561-036A
CONNECTOR (CIRC),WAFER
MA V 8283-0212 WH ELCO
CN603
CS5D1
6600M000026
SWITCH,PUSH
MPU12970MLB0 VCR CST IN S/W MI
ES501
4931R-0085C
HOLDER ASSEMBLY
VCR DECK/MECHA END(S)
ES502
4931R-0085C
HOLDER ASSEMBLY
VCR DECK/MECHA END(S)
IC501
0IMCRMI105C
IC,MICRO CONTROLLER
M3776AMCH-1D6GP 3RD RENESAS 10
JK5L1
6612J00053A
JACK,RCA
DPAE-0385 DOOWON RGB 2004 CO
LD501
4931R-0089C
HOLDER ASSEMBLY
VCR DECK/MECHA END(S)
LED501
6301R2U011A
LED ASSEMBLY
TOS-366AGMGMRMY-B OASIS UNIVER
MS501
6600JR3002D
SWITCH,MODE
SSS-51MD-3 SHINMEI 5VDC 1MA D3
MS501
6600JR3002E
SWITCH,MODE
MMS01080ZMBO MIC 5VDC 1MA D37
PMC01
6630BK01612
CONNECTOR (CIRC),BOARD TO BOAR
JE612-A2T-12A JAE EUN 12P 2.0M
RC501
6712R1938EA
REMOTE CONTROLLER RECEIVER
TSOP2238AY VISHAY 38KHZ LGEDI
RC501
6712R1938HA
REMOTE CONTROLLER RECEIVER
356VF4 OPTO 38.0KHZ 19MM(356VF
RS501
6500RAB008A
SENSOR
KIT-3001A REEL SENSOR KODENSHI
KIT-3001A REEL SENSOR KODENSHI
RS502
6500RAB008A
SENSOR
X501
6202R-DA01B
RESONATOR,CRYSTAL
CFS-308 CITIZEN 32.768KHZ +/-
X501
6212AC2327E
RESONATOR,CRYSTAL
C-001R SEIKO EPSON 32.768 KHZ
REMARKS
ALTERNATE
ALTERNATE
ALTERNATE
ALTERNATE
*** DECK ASSEMBLY,DVD ***
A26
6721RFD090B
DECK ASSEMBLY,DVD
DVD DP-10C ZORAN882 COMBI - DI
430
1SZZR-0064B
SCREW,DRAWING
+ 1 D1.7 L7.0 SWCH18A/BZN DP8
A02
3041R-D040A
BASE ASSEMBLY
DP-10C LOADING
013
4400R-0006B
BELT
DECK/MECHA DP2-5, DP7C,DP7A OT
014
4470R-0154A
GEAR
DECK/MECHA DP8 PULLEY MOLD
015
4681R-A015A
MOTOR ASSEMBLY
DECK/MECHA LOADING DP-9 SH
017
4470R-0176A
GEAR
DVD DP-9 LOADING MOLD
018
4974R-0067A
GUIDE
DVD DP-9C UP/DOWN MOLD
019
3210R-M008A
FRAME
DP-9C UP/DOWN MOLD
020
3040R-M064A
BASE
MAIN DP-9C MOLD
435
1SZZR-0011A
SCREW,DRAWING
MACHINE
439
1SZZR-0075A
SCREW,DRAWING
+ 1 D1.7 L10.0 SWRCH18A/FZW DP
440
1SZZH-1007B
SCREW,DRAWING
+ D2.0 6MM SWRCH16A/ZNBK 4MM 1
015A
4680R-E008A
MOTOR(MECH)
FEEDING RF-300EA-1D390 MABUCHI
015B
4560R-0008A
PULLEY
MOTOR
016
6871R-9297A
PWB(PCB) ASSEMBLY,TOTAL
DP-10C LOADING/FEEDING
A03
3041R-M075B
BASE ASSEMBLY
DP-10C FEEDING (MTK 1389E, ZOR
010
6850R-JW23Z
CABLE,FLAT
P=1.0 FFC UL2896(0.035X0.7) 23
021
4681R-B009C
MOTOR ASSEMBLY
DECK/MECHA DP-10 FEEDING
024
4470R-0179A
GEAR
DVD DP-9 PINION MOLD
025
4470R-0178A
GEAR
DVD DP-9 MIDDLE MOLD
030
4470R-0180A
GEAR
DVD DP-9 RACK MOLD
036
4370R-0136A
SHAFT
DVD PU, DR-02 SUS-420J2 OTHER
5 - 18
NSP
NSP
S AL LOCA. NO. PART NO.
431
1SZZR-0062A
DESCRIPTION
SPECIFICATION
SCREW,DRAWING
+ 1 D1.7 L4.5 SWCH18A/NI DP8 P
432
1SZZR-0072A
SCREW,DRAWING
+ 1 D1.7 L4.5 SWRCH18A/FZY DP8
435
1SZZR-0011A
SCREW,DRAWING
MACHINE
439
1SZZR-0075A
SCREW,DRAWING
+ 1 D1.7 L10.0 SWRCH18A/FZW DP
026
3390R-0030A
TRAY
DVD DP-9C DISK MOLD
REMARKS
A01
4861R-0016B
CLAMP ASSEMBLY
DISC DP7 - SH
001
3300R-0547A
PLATE
CLAMP
NSP
002
5016H-1016B
MAGNET
CLAMP(LDM-R608,10*5,1*1.5T)
NSP
003
4860R-0021A
CLAMP
UPPER DP7
NSP
012
5040R-0083A
RUBBER
DVD DP-6, DP-8 FRONT RIGHT 20
012A
5040R-0110A
RUBBER
DVD REAR DP8 RIGHT 20 OTHER BL
*** PWB(PCB) ASSEMBLY,TOTAL ***
A50
6871R-7861C
PWB(PCB) ASSEMBLY,TOTAL
05 LGEDI P-COMBI ZORAN W/O DIV
CN501
6631R-E007T
CONNECTOR ASSEMBLY
8283-02/9073-02ST 2PIN 60M/M P
R5J1
0RD1501F608
RESISTOR,FIXED CARBON FILM
1.5K OHM 1/6 W 5% TA26
R5J2
0RD1201F608
RESISTOR,FIXED CARBON FILM
1.2K OHM 1/6 W 5% TA26
R5J3
0RD1501F608
RESISTOR,FIXED CARBON FILM
1.5K OHM 1/6 W 5% TA26
SW507
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW508
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW509
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
SW510
556-213C
SWITCH,DETECTOR
THV10912B TACT DC 12 V 5-0 A V
5 - 19