Continuous Ink Supply System for Epson Stylus Photo 1290

Continuous
Ink
Supply System
for
Epson Stylus Photo 1290
Installation
Instruction
For ST Prefilled Version
With Auto Reset Chips
This Version of the Continuous Ink Flow System comes with Prefilled
Cartridges and Auto Reset Chips. You just need to fill the Reservoir bottles
and print! The whole operation is very easy. It’s really an effective tool to
save your money.
CIS for
EPSON Stylus
Photo
1290 Instruction
Thank you for purchasing ST Continuous Ink Supply System. We appreciate
your support and will try our best to make your experience with our products a
pleasant one. Printing has been a different experience ever since you installed
ST Continuous Ink Supply system on your own printer. Just imagining being
able to print without regard to the ink level in those expensive little cartridges.
Please take your time installing ST Continuous Ink Supply system. Do not
remove your old cartridge until you have the ST CIS system primed and ready to
install (to prevent the drying of heads). In addition, make sure you are getting
perfect nozzle checks before installing the ST CIS system. The ST CIS system
won’t be able to work properly if the nozzles are previously clogged.
Most people get a perfect nozzle check the first time after installing the ST
Continuous Ink Supply system; others may need to run two or three cleaning
cycles or let the printer sit for a while before they get the perfect results.
1、General Guide:
1) Components
A、CIS system 1 set
D、Refill Kit
6 pcs
B、 Air filters
E、Instruction CD
6pcs
1pc
C、Support Arm
1 set
2) Opening box inspection
a、Check whether all the accessories are ready.
b、Check whether there's the leakage of the CISS, whether some tubes have been
separated from the CISS, whether there are air bubbles in the tube (If there exists more
than 20CM air space, please kindly to contact with the local dealer)
2、Printer testing:
1) Check whether the printer is in normal condition, like mechanical status, lubrication
status etc.
2) Print testing lines to ensure the printing head is good condition.
3) Print pictures to see whether the printing image is ok.
3、Installation Procedures:
1) First step
Put the CISS on the left side
of the printer. In the meantime
place all the tubes at correct
position.
Pull out the small rubber plug
from the air hole as above
picture shown.
Place 4pcs of air filters into
air holes, the thicker side
is down into tank.
2)Second step: Remove cartridge
Press the ink cartridge replace
button
Move the cartridge-car to the cartridge
replace position
Unplug the power
3) Second step: Set up the Continuous Ink Supply System
Remove original cartridge
Insert our no-sponge cartridge
into printer carefully
4)Fix Support Arm
Close the cover for cartridge
Tear off the sticker
Fix the balance arm
Fix the arm on the 26cm right far from
you printer
Tear off the sticker of clamp
Tear off the sticker
Attached the clamp on your printer
and let it parallel with printer
5) Fiveth step : Install tubeline
Insert tubelline through the arm
Finished
6) Sixth Step: Adjust the tubeline
Adjust the tubeline,remove the
Make sure tubline will not meet
Make sure the lengh of tubline is
Cartridge-car back and forth
printer when printing
enough to reach the far left and right
Too long
twist
Perfect
7)Seventh step
Instert the plug
Turn on the power switch check
wether all thing is usual
8)Eighth step: Nozzle check
Usual
Broken line
The nozzle check patterns are in broken-line, mostly because of small dusk entered into the nozzle, after
repeated cleaning, if there is still a few broken line,
the nozzle check pattern, maybe it works well.
4、Reset Procedure:
pls let the printer don’t work about 1 hour, then print
If the indicator light flashing when printing, it tells that you need to reset the chip to full
status. Please turn off your printer for about 30 seconds and switch it back on. Ink meter bar
shall show full ink. You can start printing as usual.
5、Refill Ink:
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the
above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out
the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill
ink according to the color in short supply. Then put the rubber back. (Please keep the printer
and the reservoir at the same horizontal line during the process of refilling ink.)
6、Attention for maintenance:
Take out the CISS including the inner cartridges and other components. Then
remove support arm from printer, and place the original cartridges in. Please
inquire local dealer before sending to maintenance.
Notice:
1. Please don’t take out cartridge at random after installing the CIS system.
Keep the reservoir bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out
of ink and draw air into the cartridge.
3. Don’t place the Reservoir Bottles higher or lower much than the printer.
4. To be used in a dry place between 15 and 35 degree. Avoid exposure to direct
sunlight.
5. Don’t put the continuous ink supply systems reversed or leaning during the
shipment. Please make sure all the ink filling holes and Ventilation holes are
closed tightly during the transportation. Otherwise, the ink shall leak out.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the
bottom of cartridge.
Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing
temperature.
3. Avoid collision and fallen down.
Continuous
Ink
Supply System
for
Epson Stylus Photo 1290
Installation
Instruction
For ST Prefilled Version
With Auto Reset Chips
This Version of the Continuous Ink Flow System comes with Prefilled
Cartridges and Auto Reset Chips. You just need to fill the Reservoir bottles
and print! The whole operation is very easy. It’s really an effective tool to
save your money.
CIS for
EPSON Stylus
Photo
1290 Instruction
Thank you for purchasing ST Continuous Ink Supply System. We appreciate
your support and will try our best to make your experience with our products a
pleasant one. Printing has been a different experience ever since you installed
ST Continuous Ink Supply system on your own printer. Just imagining being
able to print without regard to the ink level in those expensive little cartridges.
Please take your time installing ST Continuous Ink Supply system. Do not
remove your old cartridge until you have the ST CIS system primed and ready to
install (to prevent the drying of heads). In addition, make sure you are getting
perfect nozzle checks before installing the ST CIS system. The ST CIS system
won’t be able to work properly if the nozzles are previously clogged.
Most people get a perfect nozzle check the first time after installing the ST
Continuous Ink Supply system; others may need to run two or three cleaning
cycles or let the printer sit for a while before they get the perfect results.
1、General Guide:
1) Components
A、CIS system 1 set
D、Refill Kit
6 pcs
B、 Air filters
E、Instruction CD
6pcs
1pc
C、Support Arm
1 set
2) Opening box inspection
a、Check whether all the accessories are ready.
b、Check whether there's the leakage of the CISS, whether some tubes have been
separated from the CISS, whether there are air bubbles in the tube (If there exists more
than 20CM air space, please kindly to contact with the local dealer)
2、Printer testing:
1) Check whether the printer is in normal condition, like mechanical status, lubrication
status etc.
2) Print testing lines to ensure the printing head is good condition.
3) Print pictures to see whether the printing image is ok.
3、Installation Procedures:
1) First step
Put the CISS on the left side
of the printer. In the meantime
place all the tubes at correct
position.
Pull out the small rubber plug
from the air hole as above
picture shown.
Place 4pcs of air filters into
air holes, the thicker side
is down into tank.
2)Second step: Remove cartridge
Press the ink cartridge replace
button
Move the cartridge-car to the cartridge
replace position
Unplug the power
3) Second step: Set up the Continuous Ink Supply System
Remove original cartridge
Insert our no-sponge cartridge
into printer carefully
4)Fix Support Arm
Close the cover for cartridge
Tear off the sticker
Fix the balance arm
Fix the arm on the 26cm right far from
you printer
Tear off the sticker of clamp
Tear off the sticker
Attached the clamp on your printer
and let it parallel with printer
5) Fiveth step : Install tubeline
Insert tubelline through the arm
Finished
6) Sixth Step: Adjust the tubeline
Adjust the tubeline,remove the
Make sure tubline will not meet
Make sure the lengh of tubline is
Cartridge-car back and forth
printer when printing
enough to reach the far left and right
Too long
twist
Perfect
7)Seventh step
Instert the plug
Turn on the power switch check
wether all thing is usual
8)Eighth step: Nozzle check
Usual
Broken line
The nozzle check patterns are in broken-line, mostly because of small dusk entered into the nozzle, after
repeated cleaning, if there is still a few broken line,
the nozzle check pattern, maybe it works well.
4、Reset Procedure:
pls let the printer don’t work about 1 hour, then print
If the indicator light flashing when printing, it tells that you need to reset the chip to full
status. Please turn off your printer for about 30 seconds and switch it back on. Ink meter bar
shall show full ink. You can start printing as usual.
5、Refill Ink:
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the
above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out
the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill
ink according to the color in short supply. Then put the rubber back. (Please keep the printer
and the reservoir at the same horizontal line during the process of refilling ink.)
6、Attention for maintenance:
Take out the CISS including the inner cartridges and other components. Then
remove support arm from printer, and place the original cartridges in. Please
inquire local dealer before sending to maintenance.
Notice:
1. Please don’t take out cartridge at random after installing the CIS system.
Keep the reservoir bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out
of ink and draw air into the cartridge.
3. Don’t place the Reservoir Bottles higher or lower much than the printer.
4. To be used in a dry place between 15 and 35 degree. Avoid exposure to direct
sunlight.
5. Don’t put the continuous ink supply systems reversed or leaning during the
shipment. Please make sure all the ink filling holes and Ventilation holes are
closed tightly during the transportation. Otherwise, the ink shall leak out.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the
bottom of cartridge.
Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing
temperature.
3. Avoid collision and fallen down.