DISHWASHER
DWS 935
152985 33/0
INSTRUCTION BOOKLET
en
Contents
For the user
For the installer
Important safety information
3
4
Installation instructions
Water supply connections
Water outlet hose connection
Electrical connection
20
20
21
22
Description of the appliance
4
The control panel
Before use
Setting the water softener
Rinse aid
5
5
7
Adjusting the worktop
Fitting under a counter
Levelling
23
23
23
Using your appliance
Loading your appliance
Adjusting the height of the upper basket
Use of detergent
8
8
9
10
Hints and tips
11
Washing programmes
12
Operating sequence
13
Maintenance and cleaning
Internal cleaning
Cleaning the central filter
Cleaning the large filter
External cleaning
Prolonged periods of non-operation
Frost precautions
Moving the machine
14
14
14
14
15
15
15
15
Something not working
Service and spare parts
Customer Care department
16
17
17
Guarantee conditions
18
Hints for test centres
Technical specifications
19
19
Guide to use the instruction book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
1. 2. 3.
Step by step
Hints and tips
Environmental information
2
IND15en
Important safety information
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house
and leave the appliance, always ensure that the book is left with the appliance in order that the new
owner can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of your safety. You MUST read it carefully before
installing or using the appliance.
Installation
●
This appliance is heavy. Care should be taken when
moving it.
●
It is dangerous to alter the specifications or attempt
to modify this product in any way.
●
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
●
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
●
Do not sit or stand on the open door.
●
Isolate the appliance from the power supply and
turn off the water supply after use.
●
Care should be taken when cleaning the bottom
door seal and hinge area as any exposed metal
edges may cut if care is not taken.
●
This product should be serviced by an
authorised Service engineer, and only genuine
spare parts should be used.
●
Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre. Always insist on genuine
spare parts.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Child Safety
●
●
Conservation
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
●
Keep all packaging well away from children.
●
Keep all detergents in a safe place out of children's
reach.
In the interest of the environment:
●
Materials marked with the symbol
recyclable.
●
Check with your local Council or Environmental
Health Office to see if there are facilities in your
area for re-cycling this appliance.
●
When the appliance is to be scrapped, cut off
the power supply cable and make the door
closing device unusable to prevent young
children from being trapped inside.
●
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
During Use
●
Items that are contaminated by petrol, paint, steel
or iron debris, corrosive, acidic or alkaline
chemicals must not be washed in this dishwasher.
●
Under no circumstances should you open the door
whilst the appliance is in operation. Always turn off
the appliance before opening the door.
●
Only use detergent specifically designed for use in
dishwashers.
●
Long bladed knives stored in an upright position are
a potential hazard.
●
Long and/or sharp items of cutlery such as carving
knives must be positioned horizontally in the upper
basket.
●
When finishing loading or unloading close the
door, as an open door can be a hazard.
3
are
AVV01en
Description of the appliance
1.
Water hardness adjustment
2.
Levelling spacers
3.
Upper basket stop
1
4.
Salt container
2
5.
Large filter
6.
Detergent dispenser
7.
Control panel
8.
Rating plate
9.
Rinse aid dispenser
14
3
13
12
11
4
10
5
6
10. Central filter
9
11. Lower spray arm
12. Upper spray arm
8
13. Upper basket
7
14. Worktop
IN68
The control panel
1
234
5
6
7
8
1. On/Off indicator light
5. Door handle
2. ON/OFF pushbutton
6. Programme marker
3. Pushbutton "ENERGY SAVE 50°C"
7. Programme selector dial
4. Pushbutton "HALF LOAD"
8. Programme guide
4
APP33en
Before use
Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections
comply with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener
4. Pour 1 litre of water inside the salt container and
then fill with salt
5. Fill the rinse aid dispenser.
Water hardness
Setting the water softener
The dishwasher is equipped with a water softener
designed to remove minerals and salts from the water
supply, which would have a detrimental or adverse
effect on the operation of the appliance.
The higher the content of these salts, the harder your
water is.
Water hardness is measured in equivalent scales,
Clarke, French degrees and PPM (parts per Million).
The softener should be adjusted according to the
hardness of the water in your area. Your local Water
Authority can advise you on the hardness of the water
in your area.
The dishwasher is factory set at level 2.
If this level is not suitable for your area the softener
should be adjusted.
Clarke
degrees
French
degrees
(°TH)
PPM
(Parts per
Million)
Level
Use of
salt
0-6
0-8
0 - 80
0
NO
7 - 17
9 - 20
81 - 200
1
YES
18 - 28
21 - 40
201 - 400
2
YES
29 - 42
41 - 60
401 - 600
3
YES
43 - 63
61 - 90
601 - 900
4
YES
64 - 84
91 - 120
901 - 1200
5
YES
If your water is level 0 it is already soft
and therefore there is no need to use salt.
In this case adjust the water softener to
level 1 without using salt.
To adjust the water softener
3
4
With a screwdriver turn the selector on the upper front
corner of the machine until the level required
corresponds with the marker.
5
2
2
1
AA05
5
PDU06UKen
Filling with salt
Only use salt specifically designed for use
in dishwashers.
All other types of salt not specifically
designed for use in a dishwasher, especially
table salt, will damage the water softener.
Only fill with salt just before starting one of
the complete washing programmes (not the
Rinse and Hold programme). This will
prevent any grains of salt or salty water,
which may have been spilled, remaining on
the bottom of the machine for any period of
time, which may cause corrosion.
To fill:
1. To fill with salt, unscrew the cap of the salt
container.
LE
SA LT
SA LZ
SA L
SE
2. Pour 1 litre of water inside the container (this is
necessary only before filling with salt for the
first time).
3. Using the funnel provided, pour in the salt until the
container is full.
Do not worry if water over flows from the unit when
filling with salt, this is quite normal.
4. Replace the cap making sure that there is no trace
of salt on the screw thread or on the gasket.
SR06
5. Screw on the cap tightly.
The salt container will require topping up periodically.
The salt cap has a refill indicator window in the centre.
A green float is clearly visible when there is salt
inside the container, and almost disappears when the
salt has finished reminding you to add salt.
SR11
6
SAL02en
Rinse aid
Rinse aid is automatically added during the last rinse,
ensuring thorough rinsing, spot and streak free drying.
The dispenser, which is positioned inside the door,
holds about 110 ml of rinse aid, which is sufficient for
16 - 40 dishwashing programmes, depending upon the
dosage setting.
Filling with rinse aid
1. Open the container by turning the lid (A)
anticlockwise.
2. Add the rinse aid until the container is completely
full. The indicator (B) will be completely dark.
A
3. Top up the rinse aid when the indicator (B)
becomes clear.
BR01
Ensure that the lid is closed after every refill.
Do not put liquid detergent in the rinse aid department.
Clean up any rinse aid spilt during filling with an
absorbent cloth to avoid excess foaming during the
next wash.
x 6 5 4 3
2 1
m
a
B
Adjusting the dose
According to the finish and drying results obtained,
adjust the dose of rinse aid by means of the 6 position
selector (C) (position 1 minimum dosage, position 6
maximum dosage).
Start from position 3.
Gradually increase the dose if there are drops of water
or lime spots on the dishes after washing. Reduce it if
there are sticky whitish streaks on the dishes.
BR03
x
6 5 4 3
2 1
m
a
C
BR02
7
BRI01en
Using your appliance
Loading your appliance
Before placing dishes in the machine, remove any
scraps of food, to avoid clogging the filters and
consequently reducing the performance.
Do not load very small items which can fall
through the baskets.
Open the door and slide out the baskets to load the
dishes.
UI22
The lower basket
The lower basket is designed to take saucepans, lids,
plates, salad bowls, cutlery etc.
Serving dishes and large lids should be arranged
around the edge of the basket, ensuring that the upper
spray arm can turn freely.
The two rear rows of prongs on the lower basket can
be easily lowered to allow you to load pots, pans and
bowls.
UI21
To lower the prongs:
- Slightly pull them upward and let them drop down
(see picture).
- To bring them back to the standing position, just pull
them up again.
The cutlery basket
UI18
Long bladed knives stored in an upright
position are a potential hazard.
Long and/or sharp items of cutlery such as
carving knives must be positioned
horizontally in the upper basket.
Take care when loading or unloading sharp
items such as knives.
Cutlery should be placed in the removable cutlery
basket with the handles facing downwards. If the
handles protrude from the bottom of the basket,
obstructing the lower spray arm, load the cutlery with
the handles facing upwards.
Mix spoons with other cutlery to prevent them from
sticking together.
The cutlery basket is in two parts which can be
separated to give greater loading flexibility. To separate
the two parts, slide them horizontally in opposite
directions and pull them apart. To reassemble, reverse
the procedure.
UI62
8
CES01en
The upper basket
The upper basket is designed for plates (dessert
plates, saucers, dinner plates of up to 24 cm in
diameter), salad bowls, cups and glasses.
Arrange items on and underneath the fold-down cup
racks so that water can reach all surfaces.
Glasses with long stems can be placed upside down
in the raised cup racks.
Light items (plastic bowls etc.) should be loaded in the
upper basket and arranged so they do not move.
US29
Before closing the door, ensure that the
spray arms can rotate freely.
Adjusting the height of the upper
basket
If washing very large plates (over 27 cm and up to 31
cm in diameter) you can load them in the lower basket
after moving the upper basket to the higher position.
To move to the higher position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is stable.
When the top basket is in the higher
position it will only take plates up to 20 cm
in diameter and you will not be able to use
the raised cup racks.
RC04
To lower the basket to the original position
proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and the allow the
mechanism to drop back slowly, keeping hold of it.
Never lift or lower the basket on one side
only.
After loading your machine always close
the door, as an open door can be a hazard.
9
CES04en
Use of detergent
Only use detergents specifically designed
for use in dishwashers.
We recommend the use of Finish detergents which
are available in the following options:
Finish Double Action Tablets. Each tablet has the
exact amount of detergent required, simply place in
the dispenser.
Finish Powder recommended for every day use.
Finish Liquid Gel ideal for more delicate items as fine
bone china.
Min = 15 g
Max = 30 g D
If using powder detergents proceed as follows:
M
M IN
AX
1. Open the dispenser lid by pulling the catch (D).
2. Add the detergent according to the instructions
given on the packet.
3. Always close the lid.
4. If the programme has a prewash add the required
detergent over the lid of the dispenser.
DE17
If using detergent in tablets proceed as follows:
1. For all programmes; place 1 tablet inside the
detergent dispenser.
2. Always close the lid.
3. For all programmes with prewash; place a portion
of a further tablet on the lid of the detergent
dispenser.
DE02
Insufficient quantities of detergent will
produce poor washing results, whereas an
excessive amount of detergent will not
improve washing results and is also
wasteful.
Using no more than the correct amount also
contributes to reducing pollution.
10
DET06en
Hints and tips
To save energy
Items not suitable for
dishwashers
Place dishes in the machine immediately after every
meal and wait until the dishwasher is full before
washing.
If necessary run the Rinse and Hold programme (see
"Washing Programmes" chart) so that any food scraps
do not become caked on the dishes while you are
waiting to run the complete wash programme.
Do not prewash dishes under running water.
The following items should not be washed in
the dishwasher (unless they are sold as
dishwasher proof):
- Cutlery with wooden or horn handles or
glued parts
- bronze cutlery
- saucepans with wooden handles
- aluminium ware
- crystal ware
- leaded glass
- plastic items
- antique or fine decorated china
For best washing and drying results
Before loading remove all scraps of food and soak
very heavily soiled pots and pans.
Arrange saucepans, cups and glasses etc. upsidedown.
Tilt items with convex or concave surfaces so that the
water drains off easily.
Avoid contact between the dishes as far as possible.
Wait a few minutes before removing the dishes; in this
way they will be cooler and the drying will be
improved.
Empty the lower basket first and then the upper one;
this will avoid water dripping from the upper basket
onto the dishes in the lower one.
You will improve drying results by leaving the
dishwasher door ajar for at least 15-30 minutes as
soon as the programme finishes.
Certain types of decoration can discolour when
washed in a dishwasher.
Crystal-ware and plastic objects, if not guaranteed
dishwasher proof should be washed by hand.
Certain types of glass can also become opaque
after being washed several times in a dishwasher.
A chemical reaction can occur between silver
cutlery and stainless steel cutlery. As a precaution,
do not wash together.
Iron and cast iron objects can rust and stain other
items.
Aluminium tends to go black, copper, pewter and
brass tend to stain.
If in doubt check with manufacturer of
the item.
When buying new dishes, ensure that
they are dishwasher proof.
For best results we recommend the use of Finish detergents, rinse aid and salt.
EASY
POURING
PACK
N EW
TION
DOUBLE AC
FOR A
BRILLIANT
SHINE
L I Q U I D
G E L
P O W D E R
RINSE
C O N C E N T R AT E D D I S H WA S H E R D E T E R G E N T
DE15
11
CON06en
Washing programmes
Programme
CROCKERY,
CUTLERY
POTS AND PANS
CROCKERY,
CUTLERY
POTS AND PANS
Degree of soil
Starting position
of the
programmer
Required
pushbuttons
Cycle
description
ON/OFF
Cold prewash
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying
B
ON/OFF
Main wash up to 65°C
1 cold rinse
1 hot rinse
Drying
A
50°C
ENERGY SAVE
+
ON/OFF
Cold prewash
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying
A
50°C
ENERGY SAVE
+
ON/OFF
Cold prewash
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying
B
50°C
ENERGY SAVE
+
ON/OFF
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying
+
ON/OFF
Main wash up to 50°C
1 cold rinse
1 hot rinse
Drying
A
Heavy soil
Normal soil
*
CROCKERY,
CUTLERY
POTS AND PANS
DELICATE CHINA
AND
GLASSWARE
DELICATE CHINA
AND
GLASSWARE
**
HALF LOAD
**
HALF LOAD
***
QUICKWASH
RINSE AND
HOLD
*
Light soil
Heavy soil
Normal soil
Normal soil
B
Light soil
C
+
ON/OFF
Light soil
C
50°C
ENERGY SAVE
+
ON/OFF
Partial load (to be
completed later in
the day).
D
ON/OFF
Main wash up to 50°C
1 cold rinse
1 hot rinse
Main wash up to 50°C
1 cold rinse
1 hot rinse
1 cold rinse
Testing programme for EN 50242 (see "Hints for Test Centres).
** Important!
If you select the "HALF LOAD" programmes load crockery, cutlery, pots and pans only in the lower
basket and remember to reduce the quantity of detergent.
*** This is a special programme for quick washing a full load of lightly soiled dishes, glasses and crockery
(except pots) so that you may re-use them promptly.
12
PRO30en
Operating sequence
1.
Check the filters
8.
Ensure they are clean and properly positioned
(see "Maintenance and cleaning").
2.
Check that there is rinse aid
and salt
3.
Load the dishes
Depress the ON/OFF pushbutton.
The ON/OFF indicator light will come on
and the machine will start.
If you wish to interrupt the washing
programme at any time press this button
again.
9.
Remove any scraps of food.
Pull the lower basket out and arrange the
saucepans, plates and cutlery in it.
Pull the upper basket out and arrange the
plates, saucers, glasses and cups etc. in it.
Slide the baskets back into the machine.
If you select "HALF LOAD" programmes
remember to load crockery, cutlery, pots and
pans only in the lower basket
4.
5.
7.
At the end of the washing
programme
At the end of the programme the
dishwasher will automatically stop.
The ON/OFF indicator light remains on until
the ON/OFF pushbutton is depressed.
10. Switch off the dishwasher
Switch off the dishwasher by pressing the
ON/OFF pushbutton and open the door.
Ensure that the spray arms can
rotate freely.
When the washing programme has
finished, it is recommended that the
dishwasher is unplugged and the water
tap turned off.
Measure out detergent
Add the required amount of detergent into the
dispenser according to the dosage intructions
from the manufacturer of your brand.
Close the detergent dispenser lid.
6.
Start the programme
In general it is not advisable to open the
door while the machine is working;if the
door is opened however, a safety device
ensures that the machine stops.
Close the dishwasher door
Set the programme
Turn the programme selector dial clockwise until
the letter of the programme you wish to select
corresponds with the programme marker on the
control panel.
Important!
Care must be taken if the door is opened
during the hot phase or immediately
after a programme has finished, as
steam may escape.
If necessary select the temperature of the main
wash according to the instructions in the
"Washing programmes" chart (see "Required
pushbuttons").
13
SEQ18en
Maintenance and cleaning
Internal cleaning
Ensure that the seals around the door, the detergent
and rinse aid dispensers are cleaned regularly with a
damp cloth.
We recommend the use of Finish Dishwasher Cleaner
every 3 months or run a 65°C wash without dishes
using detergent. Regular use of Finish Dishwasher
Cleaner cleans inaccessible parts, eliminates
unpleasant food odours and helps prevent the build-up
of limescale.
Cleaning the central filter
(After each wash)
Scraps of food may accumulate in the drain filter (A)
and should be removed by rinsing the filter under
running water.
To remove the drain filter
- simply pull it out by the handle.
A
Once cleaned, refit the filter by pushing it back to its
original position until it engages.
MA04
Cleaning the large filter
(Every month)
If necessary clean the large filter (B) on both sides
under running water, using a brush.
To remove the large filter
1. Remove the spray arm by pulling it upwards on one
side.
2. Turn the column (C) anticlockwise by 90° and then
slide out the filter.
3. Once cleaned refit it following the above instructions
in reverse order.
4. Ensure the filter is in its original position, the handle
of the drain filter should be pointing towards the
front of the appliance.
90°
B
C
MA05
The dishwasher must not be used without
filters.
Incorrect repositioning and fitting of the
filters will produce poor washing results.
Cleaning the filters is vital to ensure correct
operation of the machine.
14
MAN04en
External cleaning
Clean the external surfaces of the machine and
control panel with a damp soft cloth. If necessary use
only neutral detergents. Never use abrasive products,
scouring pads or solvent (acetone, trichloroethylene
etc....).
Prolonged periods of non-operation
If you are not using the machine for any period of
time you are advised to:
1. Unplug the appliance and then turn off the water.
2. Fill the rinse aid dispenser.
3. Leave the door ajar to prevent the formation of
any unpleasant smells.
4. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where the
temperature is below 0°C. If this is unavoidable, empty
the machine, close the appliance door, disconnect the
water inlet pipe and empty it.
Moving the machine
If you have to move the machine (moving house
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge hoses.
4. Pull the machine out together with the hoses.
Avoid over tilting the machine during transportation.
15
MAN03en
Something not working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling out an engineer.
Before contacting your local Service Force Centre, please carry out the checks listed below.
Important: If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or
installation a charge will be made even if the appliance is in guarantee.
Symptom
The machine will not start
Solution
●
●
●
The machine does not fill
with water
●
●
●
●
The door has not been properly closed.
The plug is not properly inserted in the power socket.
There is no current at the socket.
Ensure the water tap is open.
Ensure the mains water supply has not been cut off.
The inlet hose may be squashed or bent. Reposition the hose.
The inlet hose may be blocked. Switch off the water supply
and clean the filter.
The filters are blocked
●
Clean the filters (refer to "Maintenance and cleaning").
The spray arms are not rotating
●
Ensure the crockery is loaded correctly.
The dishwasher will not drain
●
The drain hose may be squashed or bent.
Reposition the hose.
The sink may be blocked. Clear any blockages.
The drain hose extension is not correct. Follow the
instructions for connecting to the waste.
There is no vent in the end of the drain hose.
●
●
●
The machine is noisy
●
●
Dishes are rattling against each other, refer to “Loading
your machine”.
The spray arms are knocking against the dishes. Refer to
"Loading your machine".
The door is difficult to close
●
The dishwasher is not level, or not properly built-in.
Visible lime deposits or white
film on the dishes
●
●
Check that there is salt and that the salt cap is tight.
Check that the right level of the water softener is set.
The dishes are not quite dry
●
The rinse aid has run out or too little is being used.
The dishes are not clean
(poor wash)
●
The baskets are too full.
The dishes have not been arranged properly.
The spray arms do not rotate
The spray arms are clogged.
The filters are clogged.
The filters are not in position.
Not enough detergent has been used or it is unsuitable.
The detergent is old or has gone hard.
The salt container cap is not properly closed.
The washing programme selected is too gentle.
●
●
●
●
●
●
●
●
●
16
RIM05UKen
If after all these checks, the problem persists, contact
your local Service Force Centre, quoting the model
and serial number. This information can be found on
the rating plate located on the right hand side of the
dishwasher door (see picture).
Prod.No. ........ Ser. No. .........
Mod. ........
RA01
Service and spare parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts please contact your
local Zanussi Service Force Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the
Service Centre covering your post code area. Service
Centre addresses can be found in the accompanying
Customer Care book.
Before calling out an engineer, please ensure you
have read the details under the heading "Something
Not Working" and have the model number and
purchase date to hand.
In-guarantee customers should ensure that
the checks under the heading “Something
Not Working" have been made as the
engineer will make a charge if the fault is
not a mechanical or electrical breakdown.
Please note that it will be necessary to
provide proof of purchase for any
in-guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi
appliance or for further information on Zanussi
products please contact our Customer Care
Department by letter or telephone as follows:
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727
17
GAR02en
Guarantee conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair
or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
● The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
● The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
● The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us.
● All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
● Any appliance or defective part replaced shall become the Company’s property.
● This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
●
●
●
●
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
●
●
●
●
●
●
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area.
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking in account regulations in your new country.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliance.
France
Germany
Italy
Sweden
UK
Senlis
Nurenberg
Pordenone
Stockholm
Slough
+33 (0) 44 62 29 99
+49 (0) 911 323 2600
+39 (0) 1678 47053
+46 (0) 8 738 79 50
+44 (0) 8705 727727
18
GAR03en
Hints for test centres
Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse
aid dispenser.
Test standard
EN 50242
Reference programme:
Crockery, cutlery, pots and pans 50°C
Load:
12 standard place settings
Rinse aid selector:
position 5
Detergent dosage :
25 g in the dispenser
5 g on the dispenser lid
UI48
US50
Arrangement
lower basket
Arrangement
upper basket
Technical specifications
Dimensions
Width
Height with worktop
Height without worktop
Max depth
Max depth with open door
Electrical connection
Motor rating during wash
Power of heating element
Overall power
Voltage
Water supply pressure
Minimum
Maximum
Capacity
60 cm
85 cm
82 cm
60 cm
115.2 cm
220-240 V - 50 Hz
200 W
2100 W
2300 W
50 kPa (0.5 bar)
800 kPa (8 bar)
12 place settings
19
IST28en
Installation instructions
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
Remove all packaging before positioning the
machine.
If possible, position the machine next to a water tap
and a drain.
Water supply connections
This dishwasher must be plumbed into a cold water
supply.
The water pressure must be within the limits given in
the technical specifications.
Your local Water Authority will advise you on the
average mains pressure in your area.
The dishwasher features fill and drain hoses which
can be turned either to the left or the right to suit the
installation.
The locknut must be correctly fitted to avoid water
leaks.
Avoid bends or kinks in the hose which could prevent
or slow down the water supply.
If the machine is connected to new pipes or pipes
which have not been used for a long time, you should
run the water for a few minutes before connecting the
inlet hose. This will prevent deposits of sand or rust
clogging the inlet hose filter.
20
COL08en
Water outlet hose connection
2
3
Ø
Ø
1. To the sink outlet siphon, securing it if necessary
with a clip.
18
21
1
min 4 cm
The end of the drain hose can be connected in the
following ways:
3. To a stand pipe provided with vent-hole, minimum
internal diameter 4 cm.
min 30 cm
max 100 cm
max 100 cm
2. Hooked over the edge of the sink using the special
curved plastic guide provided.
CS09
The waste connection must be at a height of between
30 cm (minimum) and 100 cm (maximum) from the
bottom of the dishwasher.
The drain hose can face either to the right or left of the
dishwasher
Ensure the hose is not bent or squashed as this could
prevent or slow down the discharge of water.
+ 2 m max
The sink plug must not be in place when the
machine is draining as this could cause the water
to siphon back into the machine.
min 30 cm
max 100 cm
Likewise the internal diameter of the couplings used
for connections to the waste outlet must be no smaller
than the diameter of the hose provided.
max 100 cm
Ø 18
Ø 21
If you use a drain hose extension it must be no longer
than 2 metres and its internal diameter must be no
smaller than the diameter of the hose provided.
CS10
21
COL09en
Electrical connection
This appliance must be earthed.
The manufacturer declines any
responsibility should this safety measures
not be observed.
If the plug that is fitted to your appliance is not suitable
for the socket, it must be cut off and the appropriate
plug fitted.
Important
The wires on the mains lead are coloured in
accordance with the following code:
Green and Yellow -Earth
Blue
-Neutral
Brown
-Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with
the markings identifying the terminals in your plug.
CE03
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
"E" or the earth symbol or coloured green and
yellow.
2. Connect the Blue (neutral) wire to the terminal in
the plug which is marked with the letter "N" or
coloured black.
3. Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter "L" or coloured
red.
The plug moulded onto the lead incorporates a 13amp
BSI362 fuse. Only ASTA or BSI fuses should be used.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the product.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
This appliance complies with the following E.E.C.
Directives:
- 73/23 or 19.2.73 (Low Voltage Directive) and
subsequent modifications;
- 89/336 or 3.5.89 (Electromagnetic Compatibility
Directive) and subsequent modifications.
22
COLUKen
Adjusting the worktop
You can move the worktop forward or backward by 25
mm in order to align the machine with other kitchen
units.
Simply unscrew the two rear retaining screws, move
the top to the required position and then retighten the
screws.
IN26
Fitting under a counter
(kitchen worktop or sink)
By removing the machine’s worktop, you can install it
under a close fitting sink unit or a pre-existing top,
providing the dimensions of the recess correspond to
those shown in the picture.
570÷
820
600
Proceed as follows:
- Remove the machine’s worktop by unscrewing the
two rear retaining screws, pull from the front and
slide out the rear slots, lifting the worktop.
600
IN05
Insert the machine after adjusting height and levelling
with the adjustable feet. When inserting the machine,
ensure that the water inlet and drain hoses are not
kinked or squashed.
Levelling
Good levelling is essential for correct closure and
sealing of the door.
When the appliance is correctly levelled, the door will
not catch on the levelling spacers, either side of the
cabinet.
If the door does not close correctly, loosen or tighten
the adjustable feet until the machine is perfectly level.
23
INS18en