Mounting Options—Metal Bracket Installation Quick Reference Wall Plate Mounting Bracket (Metal) To be installed and or used in accordance with the appropriate electrical codes and regulations. Tools Required: Wall board saw, Pliers The IP Endpoint Company Instructions: One-Gang Low Voltage Mounting Bracket (Metal) 011184, RAL 9002, Gray White, Standard 011185, RAL 9003, Signal White, Optional 1. Use the inside area of the bracket to trace the hole cut onto the wall. 2. Using a wall board saw or matt knife, cut along the stencil line. Optional Gasket VoIP Remote Call Button As an option to the CyberData V2 speaker, the V2 Remote Call Button enables calls to the V2 Speaker that can be initiated or answered from a remotely-mounted switch. 3. Place bracket against the wall opening. Mounting Screw (2x) Wall Opening Bend tabs up and down against inside wall to secure bracket. When enabled through the Web interface, if the Remote Call Button is pressed, the speaker would initiate a SIP call to a predetermined extension. 4. Bend tabs up and down against the inside wall to secure the bracket. When the V2 Speaker is called from a remote phone and Auto-Answer is not enabled within the unit’s Web interface, the LED on the Remote Button will blink. The call will be answered when the button is pressed. 5. Place the optional gasket over the metal bracket. 6. Mount the flush mount wall plate to the bracket. Typical Call Button System Installation Remote Call Button Assembly 802.3af Compliant Ethernet Hub 1 2 3 4 5 6 Mounting Options—Plastic Bracket Wall Plate Mounting Bracket (Plastic) To be installed and or used in accordance with the appropriate electrical codes and regulations. Tools Required: Wall board saw, Philips screwdriver Instructions: One-Gang Low Voltage Mounting Bracket (Plastic) 1. Use the inside area of the bracket to trace the hole cut onto the wall. 2. Using a wall board saw or matt knife, cut along the stencil line. Optional Gasket 3. Place bracket through the wall opening. Mounting Screw (2x) Wall Opening Tighten screws to pull Flagnuts against inside wall to secure bracket. 4. Tighten screws to pull Flagnuts against the inside wall to secure the bracket. 5. Place the optional gasket over the plastic bracket. Remote Call Button Speaker IP Phone IP PBX Server Getting Started • Create a plan for the locations of your Call Buttons. • Prior to installation, consult local building and electrical code requirements. • WARNING: This enclosure is not rated for any AC voltages! Parts 6. Mount the flush mount wall plate to the bracket. (1) Call Button Assembly Remote Call Button Assembly Optional Parts (Not Included) (1) Optional One-Gang Box (Metal) (1) Optional Gasket (1) Optional One-Gang Box (Plastic) Contacting CyberData Corporate Headquarters CyberData Corporation 3 Justin Court Monterey, CA 93940, USA Phone: 831-373-2601 Fax: 831-373-4193 www.CyberData.net Sales: (831) 373-2601 ext. 334 Support: 831-373-2601 ext. 333 Web: http://www.cyberdata.net/support/contactsupportvoip.html RMA Dept: (831) 373-2601 ext. 136 Email: RMA@CyberData.net RMA Status: http://www.cyberdata.net/support/rmastatus.html (1) Wall Mounting Kit (1) Optional One-Gang, Low Voltage, Mounting Bracket (Metal) (1) Optional One-Gang, Low Voltage, Mounting Bracket (Plastic) (2) Mounting screws Warranty information is available at: Web: http://www.cyberdata.net/support/warranty/index.html © 2012, CyberData Corporation, ALL RIGHTS RESERVED 930464A Quick Reference Quick Reference 930464A © 2012, CyberData Corporation, ALL RIGHTS RESERVED Dimensions Connections Speaker AUX POWER (+) (+12VDC @ 1A) AUX SPEAKER (-) AUX SPEAKER (+) BTN SENSE GND LINE OUT (-) LINE OUT (+) BUTTON LED (-) AUX POWER (-) RELAY COM RELAY NO BUTTON LED (+) BTN SENSE J10 J9 Mounting Options—One-Gang Box (Metal or Plastic) To be installed and or used in accordance with the appropriate electrical codes and regulations. Back View Wall Plate Mounting Bracket One-Gang Box (Metal or Plastic) Tools Required: Wall board saw Instructions: One-Gang Box (Plastic) 1. Use the outside area of the One-Gang Box to trace the hole cut onto the wall. 2. Using a wall board saw or matt knife, cut along the stencil line. Optional Gasket 3. Place One-Gang Box through the wall opening. 4. Optional: Nail the One-Gang Box to the stud or connect it to the set screw connect and conduit. Mounting Screw (2x) Wall Opening One-Gang Box (Metal) 5. Place the optional gasket over the One-Gang Box. 6. Mount the flush mount wall plate to the One-Gang Box. Remote Call Button Assembly © 2012, CyberData Corporation, ALL RIGHTS RESERVED 930464A Quick Reference Quick Reference 930464A © 2012, CyberData Corporation, ALL RIGHTS RESERVED