Cadillac ESCALADE H0410 Owner`s manual

®
CUSTOM EDITION
Please read this
this manual and save it
with
sales receipt.
receipt.
with your
your original
original sales
Tools needed for assembly: Phillips Screwdriver
(not included); Assembly Tool (included). Use only
with a Power Wheels®
Wheels® 12
12 Volt
Volt Lead
Lead Acid Rechargeable
Battery with Built-in Thermal
Thermal Fuse
Fuse and
and Power
Power Wheels®
Wheels®
12 Volt Charger with Type 12V Connector
(both included). Requires four "C" (LR14) alkaline
batteries for FM Radio operation.
Product features may vary
from the picture above.
25-2201-41625
Owner's Manual
Cadillac, the Wreath & Crest Emblem, Escalade, all related Emblems
and vehicle body designs are General Motors Trademarks used under
license to Fisher-Price.
with Assembly
Instructions
For Model M0410
H0410
A
TABLE
TABLE
OF
OF
CONTENTS
CONTENTS
A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
D Parts Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
E Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
F Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
G Decoration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
H Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
I Battery Care and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
J Safe Driving Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
K Vehicle Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
L FM Radio Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
M Charge Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
N Vehicle Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
O FCC Note . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
P Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Q Problems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
A
IMPORTANT INFORMATION
• Your new vehicle requires adult assembly. Please set aside at least
60 minutes for assembly.
• You must charge your battery for 18 - 30 hours before you use your
vehicle for the first time. We recommend that you start charging
your battery before beginning assembly. Please see Battery Charging
beginning on page 8 for detailed instructions.
• Read this manual carefully for important safety information and
operating instructions before using your vehicle. Keep this manual
for future reference as it contains important information.
• This vehicle is designed for use on: grass, asphalt and other hard
surfaces; on generally level terrain; and by children 3 years of
age and older.
• Use this vehicle ONLY outdoors. Most interior flooring can be
damaged by riding this vehicle indoors. Fisher-Price® will not be
responsible for damage to the floor if the vehicle is used indoors.
• To prevent damaging the motors and gears, teach your child to
stop the vehicle before switching direction. Do not tow anything
behind the vehicle or overload it. Do not exceed the maximum
weight capacity of 130 lbs (59 kg).
• This vehicle has adjustable play seat belts. Please note that the
adjustable seat belts are designed to be a play feature only and do
not function as protective safety restraints.
2
• For safety reasons, your vehicle has been pre-set so that it will only
operate at low speed. You must remove the high speed lock-out
screw to allow operation of the vehicle at high speed. Please see
page 26 for detailed instructions.
• If you have any questions about your Power Wheels® vehicle, please call
our toll-free service lines at 1-800-348-0751 from 9 AM to 7 PM (EST)
Monday through Friday and 11 AM to 5 PM (EST) Saturday. Trained
customer service representatives are available to take your call in English
or French. Habla Español? Si usted tiene alguna pregunta ó necesita
asistencia llame gratis 1-800-348-0755 para los Estados Unidos. Tenemos
representantes que hablan español para atender su llamada.
• For your convenience, Power Wheels® maintains an independently
owned and operated Authorized Service Center Network with more
than 300 authorized service centers nationwide. Our authorized
service centers will repair or replace parts under warranty at no extra
charge, and can perform non-warranty repairs for a minimal charge.
To find the authorized service center nearest you, please visit us
on-line at www.powerwheels.com or call 1-800-348-0751.
• To register your vehicle, please visit us on-line at
www.powerwheels.com.
M0410pr-0920
WARNINGS AND CAUTIONS
B
ELECTRICAL HAZARD
WARNING
• Battery can fall out and injure a child if vehicle tips over. Always use battery retainer.
• PREVENT FIRE
- Never modify the electrical system. Alterations could cause a fire resulting in serious injury
and could also ruin the electrical system.
- Use of the wrong type battery or charger could cause a fire or explosion resulting in
serious injury.
- Use of Power Wheels® components in products other than Power Wheels® vehicles could
cause overheating, fire or explosion.
• The battery must be handled by adults only. The battery is heavy and contains sulfuric acid
(electrolyte). Dropping the battery could result in serious injury.
• Never allow children to charge the battery. Battery charging must be done by adults only. A
child could be injured by the electricity involved in charging the battery.
• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage each time
you charge the battery. If damage or excessive wear is detected, do not use the charger or the
battery until you have replaced the worn or damaged part.
• HOT motors. Handle carefully.
RIDING HAZARD
WARNING
• Prevent Injuries and Deaths
• Direct Adult Supervision Required
• Never Ride at Night.
• Keep Children Within Safe Riding Areas.
These areas must be:
- away from swimming pools and other bodies of water to prevent drownings
- generally level to prevent tipovers
- away from steps, steep inclines, cars, roads and alleys.
• Riding Rules
Make sure children know and follow these rules for safe driving and riding.
- Always sit on the seat.
- Always wear shoes.
- Only 2 (two) riders at a time.
CAUTION
• In the unassembled state, this package contains small parts. Adult assembly is required.
• Use the charger in dry locations only.
M0410pr-0920
M0410pr-0920
3
PARTS
C
• If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product
to the store.
• Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded.
Note: Some parts of this product have been packed with a protective foam cover. After removing the foam cover, you may notice a cloudy film
on the parts. Wipe these parts with a clean, dry, soft cloth to remove this residue.
2 Doors
(Left and Right)
Vehicle
Seat
Front End
Windshield/Dash
Bumper
Grille
4
Hood
M0410pr-0920
PARTS
C
Steering Column
2 Front Wheels
(Left and Right)
Steering Wheel
Steering Wheel Cap
Speaker Box
Assembly
2 Headlights
(Left and Right)
2 Wheel Covers
2 Wings
(Left and Right)
2 Door Plates
2 Bushings
Steering Column Cap
2 Hubcaps
2 Taillights
(Left and Right)
M0410pr-0920
5
PARTS
C
12 Volt Battery
2 Short Seat Belts
12 Volt Charger
7
3
/16" Washer – 2
/8" -16 Lock Nut – 2
Long Seat Belt
5
/32 x 11/2" Pin – 1
#8 x 3/4" Screw – 37
Assembly Tool
1
/4 x 11/4" Screw – 2
Key Assembly
For your convenience, we included extra fasteners!
Note: Tighten and loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
Fasteners Shown Actual Size
6
M0410pr-0920
PARTS PICTURE
D
Note: Some parts shown are assembled on both sides of the vehicle.
11
11
10
12
19
28
13
25
29
8
20
22
7
9
2
6
1
18
17
3
14
16
15
21
27
4
23
5
24
26
1
2
3
4
5
6
7
8
Vehicle
Front End
Bumper
Grille
Headlights - 2
Doors - 2
Hood
Windshield/Dash
M0410pr-0920
9
10
11
12
13
14
15
16
Door Plates - 2
Seat
Short Seat Belts - 2
Long Seat Belt
Wings - 2
Front Wheels - 2
Wheel Covers - 2
Hubcaps - 2
17
18
19
20
21
22
23
24
Bushing - 2
/16" Washers - 2
Speaker Box Assembly
Steering Wheel
Steering Column
Taillight - 2
12 Volt Charger
12 Volt Battery
7
25
26
27
28
29
Key Assembly
Assembly Tool
Steering Column Cap
Steering Wheel Cap
5/32" x 1½" Pin - 1
Parts Not Shown
3/8"-16 Lock Nuts - 2
¼" x 1¼" Screws - 2
#8 x ¾" Screws - 37
Label Sheet
7
E
BATTERY CHARGING
ELECTRICAL HAZARD
CAUTION
WARNING
• Battery can fall out and injure a child
if vehicle tips over. Always use battery
retainer.
• PREVENT FIRE
- Never modify the electrical system.
Alterations could cause a fire resulting
in serious injury and could also ruin the
electrical system.
- Use of the wrong type battery or charger
could cause a fire or explosion resulting
in serious injury.
- Use of Power Wheels® components in
products other than Power Wheels®
vehicles could cause overheating, fire
or explosion.
• The battery must be handled by adults
only. The battery is heavy and contains
sulfuric acid (electrolyte). Dropping the
battery could result in serious injury.
• Never allow children to charge the battery.
Battery charging must be done by adults
only. A child could be injured by the electricity involved in charging the battery.
• Read the safety instructions on the battery.
• Examine the battery, charger and their
connectors for excessive wear or damage
each time you charge the battery. If
damage or excessive wear is detected, do
not use the charger or the battery until you
have replaced the worn or damaged part.
8
Use the charger in dry locations only.
About Thermal Fuses
Your Power Wheels 12 volt battery is equipped with a built-in
thermal fuse. The thermal fuse is a self-resetting safety device which
automatically “trips” and shuts down operation of the vehicle if the
vehicle is overloaded or the driving conditions too severe. Once a fuse
has “tripped”, remove your foot from the pedal and wait approximately
25 seconds before operating the vehicle again. To avoid repeated
automatic shut-downs, do not overload the vehicle by exceeding
the 130 lbs (59 kg) maximum weight capacity or by towing anything
behind the vehicle. Avoid severe driving conditions, such as driving up
slopes or running into fixed objects, which can cause the wheels to
stop spinning while power is still being supplied to the motors
and make sure your child stops the vehicle before switching speeds
or direction.
If a thermal fuse in a battery continually trips under normal driving
conditions, please contact your local Power Wheels® Authorized
Service Center. For the location of the Authorized Service Center
nearest to you, visit us on-line at www.powerwheels.com,
or call 1-800-348-0751.
Important Notes
• Your new battery must be charged for at least 18 hours before
you use it in your vehicle for the first time.
• We recommend that you start charging your battery before
beginning assembly of your new vehicle.
• The battery must be upright while charging.
• The charger is not a toy.
• Do not short circuit the battery.
• You do not need to remove the battery from your vehicle to
recharge it.
• Before charging the battery, examine the battery case for cracks
and other damage which may cause sulfuric acid (electrolyte) to
leak during the charging process. If damage is detected, do not
charge the battery or use it in your vehicle. Battery acid is very
corrosive and can cause severe damage to surfaces it contacts.
• Do not charge the battery on a surface (such as a kitchen counter
top) which could be damaged by the acid contained inside the
battery. Take precautions to protect the surface on which you
charge your battery.
• Use only a Power Wheels® 12 volt charger with "12V" connector
(input 120 VAC, 60 Hz with an output of 12 VDC, 1200 mA)
to charge your Power Wheels® 12 volt battery.
Adults Note: Regularly examine the charger for damage to the
cord, plug, housing or other parts that may result in the risk of fire,
electric shock or injury. In the event of any damage, do not use
the charger until the damage has been properly repaired. Please
call 1-800-348-0751.
• If your battery is old and will not accept a charge, do not leave it in
the vehicle. Always remove a dead battery from the vehicle.
M0410pr-0920
E
BATTERY CHARGING
ASSEMBLY
F
WARNING
Power Indicator
Children can be harmed by small parts,
sharp edges and sharp points in the
vehicle's unassembled state, or by electrical
items. Care should be taken in unpacking
and assembly of the vehicle. Children should
not handle parts, including the battery, or
help in assembly of the vehicle.
B
A
Charger
Connector
• Plug the charger connector into the battery A .
• Plug the charger into a standard wall outlet B .
Notes:
- If power flow to the wall outlet is controlled by a switch, make sure
the switch is “ON”.
- Use the charger only in a wall outlet. Do not plug the charger into
a ceiling outlet.
- The power indicator on the charger does not indicate the charge
status of your battery. The power indicator allows you to see that
there is power from the wall outlet.
• Before first-time use, charge the battery for at least 18 hours.
Never charge the battery longer than 30 hours.
• Recharge the battery for at least 14 hours after each use of your
vehicle. Do not charge the battery longer than 30 hours.
• Once the battery is charged, pull firmly on the charger connector
to disconnect it from the battery. Unplug the charger from the wall
outlet. The battery is now ready to be installed in your vehicle.
Please see the Battery Installation section on page 23 for detailed
instructions on installing your battery. If your battery is already
installed in your vehicle, simply re-connect the motor harness
connector to the battery. Close the hood.
M0410pr-0920
Bushing
Front Axle
7/16"
1
Washer
RIGHT SIDE VIEW
• Slide a 7/16" washer onto a front axle.
• Fit a bushing (flat side first) onto the front axle.
• Repeat this procedure to assemble the other 7/16" washer and
bushing to the other front axle.
M0410pr-0920
9
ASSEMBLY
F
3/8" -16
Lock Nut
Front Axle
Front Wheel
2
Hint: There is a right and a left front wheel. Place the right wheel
(marked R) on the passenger side of the vehicle, and the left wheel
(marked L) on the driver side of the vehicle.
• Place a front wheel onto each front axle.
4
Assembly Tool
• Place a 3/8" -16 lock nut (rounded side out) onto a front axle.
IMPORTANT: Tighten the lock nut firmly using the closed end of the
assembly tool.
• Repeat this procedure to fasten the other front wheel assembly with
the other 3/8" -16 lock nut.
Wheel Cover
3
Front Wheel
Hubcap
• Fit a wheel cover onto each front wheel.
5
Wheel
Cover
• Align the slot in a hubcap with the rib in the wheel cover. "Snap" a
hubcap into the center of each wheel cover.
10
M0410pr-0920
ASSEMBLY
F
Front End
Battery
Compartment
8
Vehicle
TOP VIEW
• Insert two 1/ 4" x 11/ 4" screws inside of the battery compartment and
into the front end of the vehicle. Tighten the screws.
6
• Fit the front end onto the vehicle.
• Insert the tabs on the back edge of the front end into the slots in
the vehicle.
Front End
Front End
Bumper
9
RIGHT SIDE VIEW
• Fit the bumper onto the front end.
7
• Insert two #8 x 3/ 4" screws through the front end and into the
vehicle. Tighten the screws.
M0410pr-0920
M0410pr-0920
11
ASSEMBLY
F
Bumper
10
Grille
• Insert seven #8 x 3/ 4" screws into the bumper and tighten.
12
• Insert two #8 x 3/ 4" screws the top of the grille. Tighten the screws.
Grille
25
Bumper
24
11
• Fit the grille onto the bumper.
• Push down to fit the tabs on the grille into the slots in the bumper.
12
13
• Before applying the labels, wipe the surface of the vehicle with a
clean, dry cloth to remove any dust or oils.
• Place the labels exactly as shown in the illustration.
• For best results, avoid repositioning a label once it has been applied
to the vehicle.
M0410pr-0920
ASSEMBLY
F
Doors
Headlights
14
• Fit the headlights (left and right) onto the bumper.
16
• Fit the door pegs onto the holes near the front end of the vehicle.
Hint: There is a left and right door. They are designed to be
assembled one way.
Plates
Headlights
15
• Insert two #8 x 3/ 4" screws into the top edge of each headlight.
Tighten the screws.
17
• Fit the large hole on the plates to the door posts.
• Align the holes in the plates with the holes in the top side of
the vehicle.
M0410pr-0920
13
ASSEMBLY
F
Windshield/Dash
Dash
Connectors
Radio
Connectors
18
20
• Insert three #8 x 3/ 4" screws into each plate and tighten.
Dash
Connector
Motor Harness
Connector
• Open the doors on the vehicle.
• Place the windshield/dash on top of the front end of the vehicle.
• Plug both dash connectors together.
• Plug both radio connectors together.
Hint: If the connectors do not fit together, do not force them. Simply
turn one of them over and try again!
Front
Windshield/
Dash
19
Radio
Connector
BACK VIEW
• Separate the radio and dash connector wires from the motor
harness connector.
• Position the motor harness connector towards the front of the
vehicle and into the battery compartment.
• Position the dash connector and radio connector wires toward the
back of the vehicle.
14
21
FRONT VIEW
• Fit the tabs on the windshield/dash into the slots in the front end of
the vehicle.
M0410pr-0920
ASSEMBLY
F
IMPORTANT! Turn the vehicle on its side or over to complete
assembly steps 24-29.
A
B
Steering
Metal
Vehicle
Column
Bar Hole
Hole
22
• Insert four #8 x 3/ 4" screws into the base of the windshield/dash.
Tighten the screws.
Dash
24
BOTTOM VIEW
• Wipe the steering column with a paper towel to remove any
excess lubricant.
• First, insert the straight end of the steering column down through
the hole in the metal bar A ; then through the hole in the vehicle
floor B ; and finally, out through the hole in the dash.
Steering
Column
Steering
Rod
23
DASH VIEW
• Insert two #8 x 3/ 4" screws into the sides of the windshield/dash.
Tighten the screws.
• Close the doors on the vehicle.
25
• Insert the curved end of the steering column through the hole in the
steering rod.
M0410pr-0920
15
ASSEMBLY
F
Large Opening
Steering Wheel
Steering Wheel Cap
Steering Column
28
26
DASH VIEW
• Position the steering wheel so that the large opening is UP.
• Fit the steering wheel onto the steering column.
• Insert and "snap" the steering wheel cap into the center of the
steering wheel.
Steering
Column Cap
Press Wheel
29
27
Lift Steering
Column
• While pressing down on the steering wheel, grasp the steering
column under the dash and pull it up as far as it will go.
• Insert the 5/ 32" x 11/ 2" pin through the hole in the steering column.
• Grasp the steering column again and pull down to fit the pin into the
center of the steering wheel.
16
• Fit the steering column cap
onto the end of the
steering column.
• Insert a #8 x 3/4" screw through the large opening in the steering
column cap and into the hole in the steering column. Tighten
the screw.
• Turn the vehicle upright.
M0410pr-0920
ASSEMBLY
F
1.5V x 4
"C" (LR14)
Key
Assembly
Battery Safety Information
30
• Insert and "snap" the key assembly into the slot in the dash.
Loosen These
Screws
In exceptional circumstances, batteries may leak fluids that can cause
a chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely. Do
not dispose of product in a fire. The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Hood
• Locate the FM Radio on the dash.
• Loosen both screws in the battery compartment door.
• Remove the battery compartment door.
• Insert four, new "C" (LR14) alkaline batteries.
Hint: We recommend using alkaline batteries for longer life.
• Replace the battery compartment door and tighten the screws.
• When sounds become faint or stop, it’s time for an adult to change
the batteries! Please refer to page 27 for general information and
tips for use of the FM Radio.
31
FRONT VIEW
• Fit the long tabs on the hood into the slots in the front end of
the vehicle.
M0410pr-0920
17
ASSEMBLY
F
TOP VIEW
Seat
Hood
Tab
Slot
32
34
• Lower and fit the side tabs on the hood into the slots on each side
of the front end of the vehicle.
Slots
• Insert the two tabs on the front edge of the seat into the slots in
the vehicle.
Short Seat Belts
Seat
Seat
Long Seat Belt
33
• Insert the fastener end of a short seat belt strap through the slot
near the outer edge of the seat. Make sure the side of the seat belt
with the fastener faces the outer edge of the seat.
• Pull the short seat belt strap completely through the slot until the
last T-loop at the opposite end of the belt catches against the slot.
You will pull one T-loop through the slot.
• Repeat this procedure to assemble the other short seat belt strap.
• Insert each fastener end of the long seat belt strap through a slot in
the center of the seat. Make sure the fasteners face the outer edge
of the seat.
• Pull each side of the long seat belt strap evenly through the slots.
Make sure to pull each T-loop through a slot.
18
35
BACK VIEW
• Insert two #8 x 3/ 4" screws into the back of the seat. Tighten
the screws.
M0410pr-0920
ASSEMBLY
F
Wings
11
12
36
Taillight Tabs
• Before applying the labels, wipe the surface of the vehicle with a
clean, dry cloth to remove any dust or oils.
• First apply the inside edge of a label to the back end of the
vehicle. Next, apply the outside edge of the label to the side of
the vehicle. Then, smooth the center of the label. (The edges will
overlap slightly.)
• For best results, avoid repositioning a label once it has been applied
to the vehicle.
38
• Fit the wing tabs into the slots in the top edge near the rear of
the vehicle.
Hints:
• There is a left and right wing. They are designed to be assembled
one way.
• Make sure the tabs on the top of the taillights fit into the bottom of
each wing.
Taillights
37
• Fit the taillights (left and right) onto the rear of the vehicle.
M0410pr-0920
39
• Insert two #8 x 3/ 4" screws into each wing. Tighten the screws.
19
ASSEMBLY
F
Speaker Box Assembly
Speaker Connector
Speaker Connector
40
• Position the speaker box assembly over the back end of the vehicle.
• Plug both speaker connectors together.
Hint: If the connectors do not fit together, do not force them. Simply
turn one of them over and try again!
42
• Insert three #8 x 3/ 4" screws into the top of the speaker assembly.
Tighten the screws.
Assembly is now complete.
Speaker Box Assembly
41
• Fit the speaker box assembly onto the vehicle.
20
M0410pr-0920
DECORATION
G
Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind:
• Wash your hands before applying the labels.
• Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils.
• Place the labels exactly as shown in the illustrations.
• For best results, avoid repositioning a label once it has been applied to the vehicle.
• After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your vehicle.
Start at the center of a label, and smooth towards the outer edges to remove air bubbles.
9
9
7
18
5
2
6
4
22
23
18
FRONT VIEW
M0410pr-0920
21
DECORATION
G
19
20
8
18
10
1
18
15
3
REAR VIEW
13
14
16
17
21
DASH VIEW
22
M0410pr-0920
BATTERY INSTALLATION
IMPORTANT! Use only a Power Wheels® 12 volt lead-acid
rechargeable battery. Use of any other battery will damage your
vehicle. Make sure that you charge the battery for at least 18
hours using the enclosed Power Wheels® 12 volt charger before
operating your vehicle for the first time. Charge the battery for at
least 14 hours after each use of the vehicle. Never charge the
battery longer than 30 hours. Failure to follow these instructions
may damage your battery and will void your warranty.
H
Power Wheels®
12 Volt Battery
Hood
Battery
Retainer
Battery
Compartment
2
Power Wheels®
12 Volt Battery
Motor Harness
Connector
• Push the battery retainer.
• Place the 12 volt battery into the battery compartment. Make sure
the battery retainer slides over the battery.
• To close the hood, fit the tabs on the front end of the hood into the
slots on each side of the front end of the vehicle.
1
• Lift the hood to access the battery compartment.
• Plug the motor harness connector into the 12 volt battery.
M0410pr-0920
23
BATTERY CARE AND DISPOSAL
I
Care
If a battery leak develops, avoid contact with the leaking acid and
place the damaged battery in a plastic bag. See information below
for proper disposal.
If acid comes in contact with skin or eyes, flush with cool water for
at least 15 minutes and call a physician.
If acid is internally ingested, give water, milk of magnesia or egg
whites immediately. Never give emetics or induce vomiting. Call
a physician.
• Charge a new battery for at least 18 hours before first use.
Never charge the battery longer than 30 hours. Overcharging or
undercharging the battery may shorten battery life and decrease
vehicle running time.
• After the first charge, recharge the battery for at least 14 hours
after each use. Never charge the battery longer than 30 hours.
Charge the battery after each use, regardless of how long the
vehicle was used.
• The battery must be upright while charging.
• Do not allow the battery to run down completely before charging.
• Charge the battery before storing the vehicle.
• Charge the battery at least once per month, even if the vehicle has
not been used.
• Leaving the battery in a discharged condition will ruin it.
• Always remove an exhausted battery from the vehicle. Battery
leakage and corrosion can damage the vehicle.
• Do not store the battery on a surface (such as a kitchen counter
top) which could be damaged by the acid contained inside the
battery. Take precautions to protect the surface on which you store
the battery.
• Do not store the battery in temperatures above 75° F or below -10° F.
• Use only a Power Wheels® 12 volt battery. Remember to charge the
new battery for at least 18 hours before first use.
• Prevent the battery from moving freely inside the battery compartment. Always use the battery retainer to secure the battery in
the battery compartment.
• Examine the battery, charger and their connectors for excessive
wear or damage each time you charge the battery. If damage is
detected, do not use the charger or the battery until you have
replaced the worn or damaged part.
24
Disposal
• Your Power Wheels® battery is a non-spillable, sealed lead-acid
battery. It must be recycled or disposed of in an environmentally
sound manner.
• Do not dispose of a lead-acid battery in a fire. The battery may
explode or leak.
• Do not dispose of a lead-acid battery in your regular, household
trash. The incineration, landfilling or mixing of sealed lead-acid
batteries with household trash is prohibited by law in most areas.
• Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
• Return an exhausted battery to a federal or state approved lead-acid
battery recycler, such as a Power Wheels® authorized service center
or a local seller of automotive batteries. For the authorized service
center location nearest to you, please visit us on-line at
www.powerwheels.com or call 1-800-348-0751. Contact your
local waste management officials for other information regarding
the environmentally sound collection, recycling and disposal of
lead-acid batteries. If you live in the State of Florida or the State of
Minnesota, it is prohibited by law for anyone to throw away lead-acid
batteries in the municipal waste stream.
M0410pr-0920
SAFE DRIVING RULES
RIDING HAZARD
WARNING
• Prevent Injuries and Deaths
• Direct Adult Supervision Required
• Never Ride at Night.
• Keep Children Within Safe Riding Areas.
These areas must be:
- away from swimming pools and other
bodies of water to prevent drownings
- generally level to prevent tipovers
- away from steps, steep inclines, cars,
roads and alleys.
• Riding Rules
Make sure children know and follow
these rules for safe driving and riding.
- Always sit on the seat.
- Always wear shoes.
- Only 2 (two) riders at a time.
J
Teach Safety Rules to Children
While children can quickly develop the skill necessary to drive this
vehicle, it is important to remember that their judgment skills are still
very immature. Unsupervised driving by children can lead to serious
injury. Before children use this vehicle, an adult should carefully
evaluate the driving area as well as the children’s skill level and ability
to drive this vehicle safely. Children are not always able to recognize
or anticipate hazards, even when they have been taught about them.
There is no acceptable substitute for direct adult supervision.
Teach appropriate safety rules to your child before allowing operation
of this vehicle. These rules should also be reviewed with neighborhood
children or other playmates who want to drive this vehicle.
Riding Rules
Make sure children know and follow these rules for safe driving:
1. Always sit on the seat.
2. Always wear shoes.
3. Only 2 (two) riders at a time. A child who is not sitting on the seat or
who is standing on the vehicle could fall off, cause a tip-over or block
the driver’s view. A child could be seriously injured.
4. Do not allow any child to drive the vehicle in the street or near
moving (motorized) vehicles.
5. Do not allow any child to drive near bodies of water (such as pools
or creeks), obstructions (such as furniture, low tree limbs or play
equipment), or drop-offs (such as stairs or decks).
6. Do not allow any child to drive the vehicle in the dark. A child could
encounter unexpected obstacles and have an accident. Operate the
vehicle only in the daytime or a well-lit area.
7. Do not allow your child to drive on sloped or inclined surfaces.
Restrict your child’s driving to generally level ground ONLY!
8. Do not allow your child to drive down or across a steep slope.
- The vehicle may gain unsafe speed, even if the pedal is released
to stop.
- The vehicle may tilt and tip over.
- The wheels could lose traction, causing the vehicle to slip.
9. Do not allow your child to drive up steep inclines. The motor may
stop and the vehicle could roll backwards at an unsafe speed.
10. Never put anything near any moving parts. Rotating parts such as
motors, gear boxes and wheels can snag fingers, hair, etc., causing
serious injury. Do not allow operation of the vehicle when it is on its
side or in an upside-down position.
11. Do not operate the vehicle near flammable vapors (gasoline, paint
thinner, acetone, liquid wax, etc.). The vehicle’s electrical switches,
like most electrical switches, emit an internal spark when first turned
on or turned off. The presence of flammable liquids or vapors could
cause an explosion or a fire. Keep all flammable products in tightly
sealed containers and away from the vehicle.
12. Do not allow a child to operate the vehicle without direct adult
supervision. To prevent unsupervised use of the vehicle, disconnect
the motor harness from the battery when the vehicle is not in use.
M0410pr-0920
25
VEHICLE OPERATION
K
IMPORTANT! Use this vehicle ONLY outdoors. Most interior flooring can be damaged by riding this vehicle indoors. Fisher-Price®
will not be responsible for damage to the floor if the vehicle is
used indoors.
Beginner Use - Low Speed Drive
As assembled, your vehicle is ready to roll in low speed
(21/2 mph, maximum). It has been pre-set so it will only operate in
low speed. After your child has mastered the basic skills of driving
and understands the rules for safe driving, it’s time to remove the
high speed lock-out screw to allow the vehicle to operate in low or
high speed. See the instructions on this page to remove the high
speed lock-out screw.
1
2
3
• Your vehicle has a patented, electronic braking system that
automatically stops the vehicle when your child’s foot lifts from
the pedal. Make sure your child is comfortable with steering the
vehicle and automatically knows how to stop.
Advanced Use - High Speed Drive
Place
lock-out screw
here for storage.
Remove
lock-out screw
for high speed.
• Make sure the shifter is in the low speed
position 1 .
2
• Press down on the foot pedal
. The vehicle goes forward at a
maximum of 2 1/2 mph 3 . Help your child practice steering to learn
how far and how quickly to turn the steering wheel when driving
forward in low speed.
To Back Up
1
2
• Before you disconnect the high speed lock-out, make sure your
child knows how to steer, how to start and stop the vehicle and
knows the rules for safe driving. When the high speed lock-out is
disconnected, the vehicle can be driven forward in low speed
(2 1/2 mph, maximum) or high speed (5 mph, maximum).
• Make sure the shifter is in the reverse
position.
• Loosen and remove the screw in the shifter box.
• Place the lock-out screw into the hole in the vehicle for future use.
It can be re-inserted into the shifter box to lock-out high speed.
3
To Drive
1
IMPORTANT! To avoid damaging the motors and gears, stop the
vehicle before shifting from forward to reverse.
• Once your child is completely comfortable with operating the vehicle
in the forward mode, introduce reverse
.
• Make sure the shifter is in the reverse
position 1 .
2
• Press down on the foot pedal
.The vehicle will go in reverse at a
maximum of 2 1/2 mph 3 . The vehicle is designed to operate in low
speed only in reverse. Help your child practice steering to learn how
far and how quickly to turn the steering wheel when driving
in reverse.
26
2
3
• Make sure the shifter is in the high speed
position 1 .
2
• Press down on the foot pedal
. The vehicle goes forward at a
maximum of 5 mph 3 . Help your child practice steering to learn
how far and how quickly to turn the steering wheel when driving
forward in high speed.
M0410pr-0920
FM RADIO USE
L
Volume
Scan
Reset
Power
Scan
Main Reset
Power/Volume
• Press the power button
to turn on or off.
• Turn the volume dial
to adjust to a comfortable listening level.
Hint: The FM Radio will turn off automatically after about one hour of non-use.
FM Radio
•
•
•
•
Press the scan button
to find a station.
Press the scan button
again to go to the next station.
To reset the radio to the first station, press the scan reset button
.
FM Radio reception varies from area to area. If the tuned station is lost due to poor reception, the radio automatically scans to the next
station with good reception.
Hint: Each time power is turned off and back on, the FM Radio will reset to the first station.
IMPORTANT! If the FM Radio functions erratically, press the main reset button with the point of a pen (or similar object).
M0410pr-0920
27
M
CHARGE INDICATOR
Button
12 VOLT BATTERY
CHARGE INDICATOR
• Press the 12 volt battery charge indicator button to check the power
level of your battery:
All four lights means the 12 volt battery is 100% (fully) charged.
Three lights means the 12 volt battery is 75% (mostly) charged.
Two lights means the 12 volt battery is 50% charged. We
recommend recharging your battery for 14 hours.
VEHICLE CARE
N
• Check all screws, cap nuts and their protective coverings regularly
and tighten as required. Check plastic parts on a regular basis for
cracks or broken pieces.
• During snowy or rainy weather, the vehicle should be stored inside
or under a protective cover. Remember to charge the battery at
least once per month while your vehicle is not in regular use.
• Avoid operating the vehicle in wet or snowy conditions, and do not
spray the vehicle with a hose. Do not wash the vehicle with soap
and water. Water or moisture in the motors or electrical switches
can cause them to corrode, and could cause switch or motor failure.
• Avoid operating the vehicle on sand, loose dirt or gravel. Sand,
loose dirt or gravel in the motors or electrical switches can cause
them to jam, and could cause switch or motor failure.
• The vehicle can be wiped down with a soft, dry cloth. For a shiny
finish, you can wipe plastic parts with a non-wax furniture polish
applied to a soft-cloth. Do not use automotive wax. Do not use
soap and water or spray the vehicle with a hose.
• To ensure that your vehicle stays in good operating order, we
recommend that you periodically have your vehicle checked by a
Power Wheels® authorized service center. For the location of the
authorized service center nearest you, please visit us on-line at
www.powerwheels.com or call 1-800-348-0751.
One or no lights means the 12 volt battery needs charging. Fully
charge your battery for 14 hours.
Hint: For the most accurate reading, do not press the battery charge
indicator while the vehicle is moving.
28
M0410pr-0920
O
FCC NOTE
(United States Only)
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
M0410pr-0920
LIMITED WARRANTY
P
Bumper-to-Bumper* Limited Warranty
*One year limited warranty from the date of
purchase on the Power Wheels® vehicle.
Six month limited warranty on the 12 volt battery.
For the original purchaser, this one year limited warranty
covers the Power Wheels® ride-on vehicle (purchased from
Power Wheels®) against defects in materials and workmanship.
The six month limited warranty applies only to the 12 volt battery
included by Power Wheels® with the original purchase of the
vehicle. This warranty covers normal use and does not cover the
Power Wheels® vehicle or battery if damaged by unreasonable
use, neglect, accident, abuse, misuse, improper service or other
causes not arising out of defects in materials or workmanship.
Evidence of any attempt at consumer repair will void this
warranty. THIS WARRANTY DOES NOT COVER, AND IS
INTENDED TO EXCLUDE, ANY LIABILITY ON THE PART OF
POWER WHEELS®, WHETHER UNDER THIS WARRANTY OR
IMPLIED BY LAW FOR ANY INDIRECT OR CONSEQUENTIAL
DAMAGES FOR BREACH OF WARRANTY. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION SO THIS
LIMITATION MAY NOT APPLY TO YOU.
Should you need service or assistance with your vehicle during
the warranty period, do not return the vehicle to the store.
Power Wheels® has provided a nationwide network of authorized
service centers. If there is not an authorized service center in
your area, please visit us on-line at www.powerwheels.com or
call Consumer Relations for information, 1-800-348-0751.
This warranty gives you specific legal rights, and you may also
have other rights which may vary from state to state.
PLEASE SAVE YOUR ORIGINAL SALES RECEIPT.
29
PROBLEMS AND SOLUTIONS GUIDE
Q
IMPORTANT! If you experience a problem with your vehicle, first check the Problems and Solutions Guide below. If you still experience a
problem, please contact Power Wheels® Consumer Relations, toll-free at 1-800-348-0751 between 9 AM and 7 PM (EST) Monday through
Friday and 11 AM and 5 PM (EST) Saturday. Or, contact your local Power Wheels® authorized service center. For the location nearest you,
please visit us on-line at www.powerwheels.com, or call 1-800-348-0751.
PROBLEM
Vehicle does not run
POSSIBLE CAUSE
Undercharged battery
SOLUTION
Charge the battery. A new battery should have been
charged for at least 18 hours before using the vehicle for
the first time. After first-time use, recharge the battery for
at least 14 hours after each use. Never charge the battery
longer than 30 hours.
Check all connectors. Make sure the charger is
tightly plugged into the battery, and that the
charger is plugged into the wall.
Make sure power flow to the wall outlet is “ON”.
30
Charger is not working
There is no sure way to tell if your charger is working unless
you have a volt meter. If you suspect there is a problem with
your charger, contact your local Power Wheels® authorized
service center. They can test your charger for you.
Tripped thermal fuse
The built-in thermal fuse may "trip" and shut down operation
of the vehicle if the vehicle is overloaded or the driving
conditions too severe. Once a fuse has "tripped", remove
your foot from the pedal and wait approximately 25 seconds
before operating the vehicle again. To avoid repeated
automatic shutdowns, do not overload the vehicle by
exceeding the 130 lbs maximum weight capacity or by towing
anything behind the vehicle. Do not drive up hills or run into
fixed objects, which can cause the wheels to stop spinning
while power is still being supplied to the motors. If a thermal
fuse continually trips, contact your local Power Wheels®
authorized service center.
Loose wires or loose connectors
Check all wires and connectors. Make sure the motor
harness connector is tightly plugged into the battery and that
there are no loose wires around the motors.
Dead battery
If your battery is old or if you have not followed Battery
Care instructions, your battery may be dead. If you are
unsure whether or not the battery are dead, you can have
it tested at your local Power Wheels® authorized
service center.
Electrical switch damage
The electrical switches can become corroded due to
exposure to water or moisture, or can jam due to loose dirt,
sand or gravel. Contact your local Power Wheels® authorized
service center for diagnosis and repair.
Motor damage
Contact your local Power Wheels® authorized service center
for diagnosis and repair.
M0410pr-0920
PROBLEMS AND SOLUTIONS GUIDE
PROBLEM
Vehicle was running but
suddenly stopped
Short run time (Less than
1 - 3 hours per charge)
POSSIBLE CAUSE
Q
SOLUTION
Loose wires or loose connectors
Check all wires and connectors. Make sure the
motor harness connector is tightly plugged into the battery,
and that there are no loose wires around the motors.
Tripped thermal fuse
The built-in thermal fuse may "trip" and shut down
operation of the vehicle if the vehicle is overloaded or the
driving conditions too severe. Once a fuse has "tripped",
remove your foot from the pedal and wait approximately
25 seconds before operating the vehicle again. To avoid
repeated automatic shutdowns, do not overload the vehicle
by exceeding the 130 lbs maximum weight capacity or by
towing anything behind the vehicle. Do not drive up hills or
run into fixed objects, which can cause the wheels to stop
spinning while power is still being supplied to the motors.
If a thermal fuse continually trips, contact your local Power
Wheels® authorized service center.
Undercharged battery
Charge the battery. A new battery should have been
charged for at least 18 hours before using the vehicle for
the first time. After first-time use, recharge the battery for
at least 14 hours after each use. Never charge the
battery longer than 30 hours.
Check all wires and connectors. Make sure the motor
harness connector is tightly plugged into the battery, and
that the charger is plugged into the wall.
Make sure power flow to the wall outlet is “ON”.
M0410pr-0920
Overcharged battery
Do not charge the battery longer than 30 hours. If you
suspect that your battery is damaged as a result of
overcharging, contact your local Power Wheels® authorized
service center. They can test the battery for you.
Battery is old and will not
accept full charge
Even with proper care, a rechargeable battery does not
last forever. Average battery life is 1 to 3 years depending
on vehicle use and use conditions. Replace only with a
Power Wheels® 12 Volt Lead-Acid Rechargeable Battery.
Do not substitute parts.
Tripped thermal fuse
The built-in thermal fuse may "trip" and shut down
operation of the vehicle if the vehicle is overloaded or the
driving conditions too severe. Once a fuse has "tripped",
remove your foot from the pedal and wait approximately
25 seconds before operating the vehicle again. To avoid
repeated automatic shutdowns, do not overload the vehicle
by exceeding the 130 lbs maximum weight capacity or by
towing anything behind the vehicle. Do not drive up hills or
run into fixed objects, which can cause the wheels to stop
spinning while power is still being supplied to the motors.
If a thermal fuse continually trips, contact your local Power
Wheels® authorized service center.
M0410pr-0920
31
Q
PROBLEMS AND SOLUTIONS GUIDE
PROBLEM
Vehicle runs in low speed, but
does not run in high speed
POSSIBLE CAUSE
SOLUTION
High speed lock-out not disconnected
The vehicle was pre-set to run only in low speed.
To allow the vehicle to run in low and high speed, you
must disconnect the High Speed Lock-Out. Follow the
instructions on page 26 to remove the High Speed
Lock-Out screw.
When the foot pedal is pressed
one rear wheel spins
Operation of vehicle in low speed
It is possible that only one rear wheel may spin when both only
rear wheels are raised off the ground and the vehicle is in
low speed. This does not necessarily indicate a problem.
Check for proper operation of the drive system by raising
the rear wheels off the ground and pressing the foot pedal.
If only one rear wheel spins, carefully press your hand on
the spinning wheel to slow it down. The other rear wheel
should begin to spin. If the other rear wheel does not begin
to spin, there may be a problem with the vehicle. Contact
your local Power Wheels® authorized service center for
diagnosis and repair.
Vehicle runs sluggishly
Undercharged battery
Charge the battery. A new battery should have been
charged for at least 18 hours before using the vehicle for
the first time. After first-time use, recharge the battery for
at least 14 hours after each use. Never charge the battery
longer than 30 hours.
Please Note: The vehicle is
designed to operate in low
.
speed only in reverse
Check all connectors. Make sure the charger connector
is tightly plugged into the battery, and that the charger is
plugged into the wall.
Make sure power flow to the wall outlet is “ON”.
32
Battery needs charging
Be sure to charge the battery after each use.
Battery is old and will not
accept full charge
Even with proper care, a rechargeable battery does not
last forever. Average battery life is 1 to 3 years depending
on vehicle use and use conditions. Replace only with a
Power Wheels® 12 Volt Lead-Acid Rechargeable Battery.
Do not substitute parts.
Vehicle is overloaded
Make sure you do not overload the vehicle by allowing
more than two riders at one time, exceeding the 130 lbs.
maximum weight capacity, or by towing objects behind the
vehicle. If the vehicle is overloaded, the built-in thermal fuse in
the battery may "trip", and automatically shut down operation
for approximately 25 seconds. Adjust the driving conditions
to prevent repeated automatic shutdowns.
Driving conditions are too stressful
Use only on generally level ground.
M0410pr-0920
PROBLEMS AND SOLUTIONS GUIDE
PROBLEM
Sometimes the vehicle doesn’t
run, but other times it does
POSSIBLE CAUSE
Q
SOLUTION
Loose wire or connector
Check all wires around the motors and all connectors to
make sure they are tight.
Motor or electrical switch damage
Contact your local Power Wheels® authorized service
center for diagnosis and repair.
Loose wire or connector
Check all wires around the motors and all connectors
to make sure they are tight.
“Dead Spot” on motor
Contact your local Power Wheels® authorized service
center for diagnosis and repair.
Damaged battery
Contact your local Power Wheels® authorized service
center for diagnosis and repair.
Child is switching between
FORWARD and REVERSE
without stopping
Teach your child to stop the vehicle before switching
direction.
Loud clacking or grinding
noise from a motor-gearbox
Broken gears
Contact your local Power Wheels® authorized service
center for diagnosis and repair.
Charger gets warm during use
It is normal for some chargers to get
warm during use and is not reason
for concern. Some chargers do not
get warm during use.
No action required.
When the foot pedal is pressed,
the vehicle won’t run without
a push
Battery’s thermal fuse constantly
"trips", but the vehicle is not
overloaded nor the driving
conditions too severe
Battery makes a sizzling or
gurgling noise when charging
M0410pr-0920
It is normal for some batteries to
make noise and swell slightly while
charging and is not reason for concern.
If your charger does not get warm during
use, it does not mean that it is not working properly.
No action required.
If your battery does not make noise or swell slightly
during charging, it does not mean that it is
not accepting the charge.
M0410pr-0920
33
PROBLEMS AND SOLUTIONS GUIDE
Q
PROBLEM
FM Radio does not function
FM Radio station
changes automatically
POSSIBLE CAUSE
SOLUTION
Power is off
Power automatically turns off after about one hour of non-use.
Press the power button
to turn it back on.
Batteries are weak or dead
Replace all four batteries with four, new "C" (LR14)
alkaline batteries.
Poor reception
You may find better reception of a particular station in a
different location.
Power was turned off and the radio
reset back to the first station
Use the scan button to reset to your favorite station.
If, after reviewing the Problems and Solutions Guide, the vehicle still fails to operate, please contact your nearest authorized service center.
34
M0410pr-0920
M0410pr-0920
M0410pr-0920
35
Before first-time use,
you must charge the battery
18 hours!
Charge the battery immediately after each use.
Charge the battery once a month, even if the vehicle
is not used or stored.
Do not return
your vehicle to the store!
Or contact your local independently owned and operated
Power Wheels Authorized Service Center.
For the location nearest you, visit us on-line at www.powerwheels.com.
®
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052 U.S.A.
©2007 Mattel, Inc. All Rights Reserved.
PRINTED IN MEXICO
M0410pr-0920
PRINTED IN CHINA
73610a-0920