Empire Comfort Systems CA-SERIES Operating instructions

800.967.2346
IMPORTANT SAFEGUARDS
11.Grounding or Polarization - Precaution should be taken so that the
grounding or polarization means of an appliance is not defeated.
12.Power Cord Protection - Power supply cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, receptacles,
and the point where they exit from the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER - SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
14.Non-use Periods - The power cord of the appliance should be
unplugged from the outlet when left unused for a long period of time.
15.Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through the openings.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
16.Damage Requiring Service - The appliance should be serviced by qualified service personnel when:
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
appliance.
B. Objects have fallen, liquid has been spilled into the appliance; or
If you have any questions please call Russound Inc. at
1-800-638-8055 or 603-659-5170.
E. The appliance has been dropped or the enclosure is damaged.
Safety Instructions:
1. Read Instructions - All the safety and operating instructions should be
read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should be
retained for future reference.
3. Heed Warnings - All warnings on the appliance in the operating instructions should be adhered to.
4. Follow Instructions - All operating and user instructions should be followed.
5. Water and Moisture - The appliance should not be used near water; for
example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
6. Carts and Stands - The appliance should be used only
with a cart or stand that is recommended by the
manufacturer. An appliance and cart combination
should be moved with care. Quick stops, excessive
force and uneven surfaces may cause the appliance
and cart combination to overturn.
7. Wall or Ceiling Mounting - The appliance should be mounted to a wall
or ceiling only as recommended by the manufacturer.
8. Ventilation - The appliance should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
appliance should not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air
through the ventilation openings.
9. Heat - The appliance should be situated away from heat sources such
as radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10.Power Sources - The appliance should be connected to a power supply
only of the type described in the operating instructions or as marked on
the appliance.
2
13.Cleaning - The appliance should be cleaned only as recommended by
the manufacturer.
A. The power supply cord or the plug has been damaged; or
C. The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally; or
17.Servicing - The user should not attempt to service the appliance beyond
that described in the operating instructions. All other servicing should
be referred to qualified service personnel.
Precautions:
1. Power – WARNING: BEFORE TURNING ON THE POWER FOR THE
FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY.
2. Do Not Touch The ST2 With Wet Hands – Do not handle the ST2 or
power cord when your hands are wet or damp. If water or any other liquid enters the ST2 cabinet, unplug the unit from power immediately and
take the ST2 to a qualified service person for inspection.
3. Location of ST2 – Place the ST2 in a well-ventilated location. Take special care to provide plenty of ventilation on all sides of the ST2 especially when it is placed in an audio rack. If ventilation is blocked, the ST2
may overheat and malfunction. Do not expose the ST2 to direct sun
light or heating units as the ST2 internal components temperature may
rise and shorten the life of the components. Avoid damp and dusty
places.
4. Care – From time to time you should wipe off the front and side panels
of the cabinet with a soft cloth. Do not use rough material, thinners,
alcohol or other chemical solvents or cloths since this may damage the
finish or remove the panel lettering.
This device complies with Part 15B of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by
Russound could void the user’s authority to operate this equipment.
TABLE OF CONTENTS
Product Introduction..........................................................................................................4-5
Component Guide
ST2-XM Front Panel .............................................................................................................6
ST2-XM Rear Panel..............................................................................................................7
ST2-RC Remote Control .......................................................................................................8
ST2-XM Setup and Connections
Basic Connections...............................................................................................................9
CAV6.6 Connections..........................................................................................................10
CA Series and ST2-KP Connections ....................................................................................11
Antenna Connections ....................................................................................................12-13
ST2-XM Operation
XM Radio Activation...........................................................................................................14
XM Radio Displays.............................................................................................................14
XM Radio Modes .........................................................................................................15-18
Front Panel Controls ..........................................................................................................19
ST2-RC Remote Control .....................................................................................................20
ST2-KP Keypad Control......................................................................................................21
UNO-S2 Keypad Control with RNET Controller.................................................................22-23
SRC2 Remote Control with RNET Controller....................................................................24-25
ST2-XM Tuner Programming
ST2 Chassis Setup Menu ...................................................................................................26
Source Number .........................................................................................................26
Update Firmware .......................................................................................................26
Factory Initialization ...................................................................................................27
System Info...............................................................................................................28
Tuner Setup Menu for XM ..................................................................................................29
Memory Name...........................................................................................................29
Bank Name ...............................................................................................................30
Controller ID ..............................................................................................................30
Diagnostics ...............................................................................................................30
Factory Initialization ...................................................................................................30
System Info...............................................................................................................31
Tuner Setup Menu for AM/FM.............................................................................................31
Memory Name...........................................................................................................31
Bank Name ...............................................................................................................32
Region ......................................................................................................................32
Backup and Restore .........................................................................................................33
Programming RNET Controller............................................................................................34
Technical Specifications ....................................................................................................35
Warranty & Repair .............................................................................................................36
3
INTRODUCTION
DESCRIPTION
Thank you for choosing the Russound ST2-XM
Smart Tuner. Whether you are adding radio to an
existing system, expanding a CA Series system
or taking advantage of the CAV6.6 or CAM6.6’s
robust RNET® communication link, the ST2-XM
Tuner is designed to meet your needs.
The ST2-XM Tuner gives you two radios in one.
The AM/FM tuner provides broadcast of local
AM/FM stations, and the XM tuner delivers all the
diversity and choices available to XM radio subscribers. The two modules share one set of controls and display on the front of the unit, but
each runs independently. This arrangement
allows two different broadcasts at the same time
in a multi-room audio distribution system.
XM satellite radio provides over 100 channels of
music, news sports, comedy, talk and entertainment. Its coast-to-coast coverage, digital quality
sound and many commercial-free music channels
make XM radio the choice for the discriminating
listener.
XM radio is a subscription-based service, and listeners can subscribe by visiting XM on the web
www.xmradio.com or by calling XM’s Listener
Care at 800-967-2346.
In addition to the traditional AM/FM broadcast
tuner function and the XM satellite access, the
ST2-XM Tuner can store up to 72 favorites, or
memory presets. These are stored in groups of
six called banks. There are six banks for each
tuner. Each preset and each bank can be given a
custom name of your choice.
The ST2-XM Tuner can be controlled from the
front panel or by the dedicated ST2-KP tuner keypad. It can also be controlled by the ST2-RC IR
remote aimed at the tuner’s front panel IR receiver. The ST2-RC IR codes can be learned into any
IR learning remote control for easy system inte4
gration. It can also be controlled by IR signals
received through the IR connections on the rear
panel from IR repeating system commonly used
in distributed audio systems.
If the ST2-XM Tuner is part of an RNET-enabled
system such as the CAV6.6-S2 system, the tuner
can be controlled through an RNET keypad such
as the UNO-S2.
The ST2 Tuner also has an RS-232 port to support fully bi-directional integration into wholehouse control systems such as Crestron® and
AMX®.
FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AM/FM Tuner
XM satellite radio
Compact single rack unit chassis
Six banks of six memory presets each per
tuner (72 total presets) for storing AM/FM
station settings or XM channels
Custom names for presets and banks
Two Favorite presets per tuner
Stereo or mono mode
Local or distant mode
Dedicated IR remote control
Individual IR direct inputs for each tuner
Front panel IR receiver
Supports two ST2-KP optional tuner keypads
RNET connections send tuner frequency and
control information to UNO keypad display
RS-232 control and programming. User
settings can be backed up and restored.
INSTALLATION APPLICATIONS
RNET-enabled System
When the ST2-XM Tuner is used with an RNETenabled device such as the CAV6.6 and is connected to it through the Link In or Link Out port,
the tuner will be controlled by the CAV6.6
through the UNO-S2 keypad. Through RNET,
tuner information such as Tuner 1 or 2, station
INTRODUCTION
frequency or channel, preset names and AM/FM
band or XM is displayed on UNO keypads. An
additional RNET device can be connected to an
existing ST2 by using the Link Out of the first
unit into the Link In of the second unit.
Before using the ST2-XM tuner with an
RNET controller, you must assign source
numbers to Tuner 1 and 2 in the ST2 Setup
Menu AND complete the controller’s Source
Setup procedure to identify the tuner as a
“Peripheral“ command type device.
IR-Controlled System
CA Series The ST2-XM Tuner can be controlled by infrared
commands received through either of the two IR
connections on the rear panel. There are two
unique IR code sets for Tuner 1 and Tuner 2,
which allow each to be controlled independently
from either IR connection. These codes can be
learned from the ST2-RC remote control into the
CAS-RC remote control. The ST2-XM contains
two individual tuners, which makes it act as two
sources in the CA system. There are two source
audio outputs and two IR connections - one for
each tuner in the ST2-XM. You will need at least
one IR link cable (Russound P/N 09-0508) for
these connections. If you are using an IR-controlled system from another manufacturer, installation should be similar. The ST2-XM IR codes
may be learned into many other manufacturers’
remote controls that have learning capability for
unified control over the A-V equipment.
RS-232 Controlled System
The ST2-XM Tuner can be controlled using the
RNET protocol provided via the RS-232 port on
the rear panel. It can also be controlled by any
RS-232-enabled control system (e.g., Crestron,
AMX). Information on RS-232 operation is available to dealers in the Document Center on the
Russound web site, www.russound.com.
BOX CONTENTS
The ST2-XM Tuner comes with the parts needed
to set up and operate the component. These
include:
•
•
•
•
•
•
•
•
ST2 Tuner (AM/FM module, XM module)
ST2-RC remote control
12VDC power supply
AM loop antenna (1)
FM antenna (1)
XM antenna (1)
RCA audio cable (2)
Rack mount ears
Please call Russound at 800-638-8055 ext. 501
for assistance if parts are missing.
Note: Optional ST2-KP keypads can be used to
provide control for the ST2-XM Tuner and are
designed to be used with IR-controlled systems.
5
COMPONENT GUIDE
ST2-XM FRONT PANEL
1
2
3
XM
64 : The Groove
4
5
6
AM/FM
7
64 : The Groove
8
9
XM
AM/FM
13
6
10
12
11
1
MAIN POWER SWITCH - Turns power on and off
2
POWER ON/OFF LED - Indicates power on or off
3
REMOVABLE COVER LENS - Covers the selection buttons on the tuner
4
BANK SELECT BUTTON - Selects bank 1-6
5
MEMORY SELECT BUTTONS - Sets and selects memory presets 1-6 for each bank
6
IR RECEIVER - Receives IR signal from remote control
7
LCD PANEL - 12-character backlit display shows station, channel, custom names, etc.
8
XM and AM/FM - Backlit tuner selection indicator
9
TNR SEL - Selects Tuner 1 (XM) or Tuner 2 (AM/FM), and accesses tuner setup menus
10
BAND - (AM/FM) Selects AM or FM band
(XM) Selects an XM Mode (Category Search, Now Playing, Display Preferences)
(ALL) Enters menu selections when programming
11
ST/MONO - (AM/FM) Selects stereo or mono mode for AM/FM, and Distant/Local reception
(XM) Press to Exit current XM Mode, hold for signal strength
12
MEM PRESET UP/DOWN - Selects memory presets starting with last preset, and toggles
through menu features
13
TUNE UP/DOWN - (AM/FM) Manually selects radio stations
(XM) Manually selects channels (Channel Up/Channel Down)
(ALL) Toggles through menu settings
COMPONENT GUIDE
ST2-XM REAR PANEL
NEWMARKET, NH U.S.A.
3
ST2
Smart Tuner
RS-232
LINK
INTERFACE
IN
4
KEYPAD PORTS
5
6
FM COAX
LOOP
ANTENNA
IR
7
8
TUNER 2
AUDIO OUTPUT
L
R
ANTENNA
9
IR
TUNER 1
AUDIO OUTPUT
L
R
10
Serial#
12VDC 1.25A
OUT
TUNER 2 AM/FM
11
MADE IN KOREA
2
1
TUNER 1 XM
1
RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible, displays frequency and other information on the UNO keypads
2
RS-232 INTERFACE - The RS-232 Interface allows the tuner to be controlled by PC or other devices
that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and programming (DB9 Cable)
3
KEYPAD PORTS - RJ-45 Keypad ports for ST2-KP tuner keypads in dedicated, non-RNET systems (Do not connect UNO keypads to these ports)
4
FM COAX - FM Antenna threaded F-connection (75 ohms) for Tuner 2
5
LOOP ANTENNA - AM antenna connection (300 ohms) for Tuner 2
6
IR INPUT - IR control input (common IR control) for Tuner 2 or Tuner 1
7
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 2
8
XM ANTENNA - XM Antenna SMB connection (50 ohms) for Tuner 1
9
IR INPUT - IR control input (common IR control) for Tuner 1 or Tuner 2
10
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 1
11
POWER SUPPLY - 12VDC external power supply connection
7
COMPONENT GUIDE
ST2-RC REMOTE CONTROL
1
1
POWER - Puts the tuner in/out of standby mode
2
TUNER CONTROL - Select TUNER 1 (XM) or
TUNER 2 (AM/FM) and all subsequent button
presses affect that tuner
2
3
TUNER 1
4
BANK SELECT - Used for direct bank selection
5
TUNE SELECT - Used for direct station or chan-
TUNER 2
(numeric input 1-6)
3
15
14
1
2
3
4
5
6
7
8
9
MEM
0
BANK
13
AM/FM
nel selection (numeric input)
4
6
TUNE UP/DOWN - Incrementally scrolls through
station or channel numbers
7
FAV 1/FAV 2 - Sets/Selects Favorite 1 or 2
preset selection on ST2-XM tuner
8
SEEK UP/DOWN -
5
6
TUNE
MEM
TUN
7
E
(AM/FM) Seeks the next tuned station
up/down
(XM) Scrolls through banks 1-6
TUNE
FAV 2
FAV 1
SEEK
OK
9
SEEK
8
LOC/
DX
10
OK (AM/FM) Confirms direct entries
(XM) Operating mode toggle
TUNE
11
LOCAL/DISTANCE (AM/FM) Optimizes station reception
12
ST/
MONO
NUMERIC INPUT - Number buttons for direct
selection of station, channel, bank, preset
PWR
9
11
STEREO/MONO (AM/FM) Selects stereo or mono broadcast
(XM) Exit current XM operating mode
10
12
TUNE UP/DOWN - Scrolls through station or
channel numbers
13
MEM UP/DOWN - Scrolls through preset stations within selected bank
8
14
AM/FM - Selects AM or FM band
15
MEM SELECT - Used for direct memory select
(numeric input 1-6)
ST2-XM SETUP AND CONNECTIONS
BASIC CONNECTIONS
Power
To power the tuner, connect the 12VDC external
power supply by inserting the power supply jack
into the power supply connection on the tuner’s
rear panel.
ST2-KP RJ-45 Connection Wiring
Audio Output
Connect one end of a dual RCA audio cable to
the Tuner 1 Audio Output connection. Keep proper channel identity. Attach the other end of the
RCA cables to the source input of the audio control system. Repeat the same procedure for the
Tuner 2 Audio Output.
IR Connections
The ST2-XM Tuner can be controlled by infrared
commands received through the two IR connections on the rear panel. The ST2-XM Tuner component contains two tuners, which must be set
up as two sources. There are two IR connections - one for each tuner in the ST2-XM. You will
need two IR link cables (Russound P/N 09-0508)
for these connections. There is a unique IR code
set each for Tuner 1 and Tuner 2, which allow
each to be controlled independently. These
codes can be learned from the ST2-RC remote
into learning-capable remotes and keypads.
If you are using an IR-controlled system from
another manufacturer, installation should be similar. The ST2-XM IR codes may be learned into
many other manufacturers’ remote controls that
have learning capability for unified control over
the A-V equipment.
RNET Connection
To link the ST2-XM to an RNET-compatible
device, use a CAT-5 passthrough patch cable
with similar wiring terminations at each end.
Connect one end of the cable to the RNET Link
In of the ST2 tuner, and connect the other end
of the patch cable to the RNET Link Out connection on the RNET-compatible device.
ST2-KP Keypad to ST2-XM Connection
(Non-RNET System)
The ST2-KP connects to the ST2-XM tuner with
CAT-5 cable, using an RJ-45 (T568A) jack on the
tuner connection end of the cable. Be sure to
use the keypad ports for the ST2-KP and NOT
the RNET link ports. The ST2-XM tuner supports
up to two ST2-KP keypads. An SA-ZX3 Keypad
Splitter can be used to add additional keypads.
Note: ST2-KP keypads are designed for use
with IR-controlled systems (non-RNET systems).
When the ST2-XM Tuner is a component of an
RNET system such as CAV6.6, the RNET-system
keypads are used.
Rack Mount Installation
The ST2-XM can be mounted in a standard component rack using the rack ears provided. Line
the rack ear’s two rows of screw holes with the
three screw holes on the side of the tuner. Use
the screws provided to secure the rack ears
onto the unit on both sides. The ST2-XM tuner
should not be installed above a high heat-producing component such as a power amplifier.
9
ST2-XM SETUP AND CONNECTIONS
CAV6.6 CONNECTIONS
UNO-S2
keypads
64:The Groove
.25A
ST2 Tuner
CAV6.6
RCA Cable
Source Connections with CAV6.6 Controller/Amplifier (RNET System)
The diagram depicts a typical setup using the ST2-XM Tuner with a CAV6.6 amplifier. Each tuner in
the ST2 unit must be connected as a separate source for audio inputs. UNO-S2 keypads are connected to the CAV6.6 keypad ports, NOT the ports on the ST2 Tuner.
10
ST2-XM SETUP AND CONNECTIONS
CA SERIES AND ST2-KP CONNECTIONS
RCA Cable
IR Link Cable
Pos (+)
Source
Neg (–)
KPL
ST2-KP
LINK
ST2
Smart Tuner
RS-232
INTERFACE
IN
KEYPAD PORTS
FM COAX
LOOP
ANTENNA
IR
TUNER 2
AUDIO OUTPUT
L
R
ANTENNA
IR
TUNER 1
AUDIO OUTPUT
L
R
Serial#
12VDC 1.25A
MADE IN KOREA
NEWMARKET, NH U.S.A.
OUT
IR Link Cable
ST2-XM
RCA Cable
CAS44
RCA Cable
Source Connections with CAS44 Controller/Amplifier
The diagram depicts a typical setup using the ST2-XM Tuner with a CAS44 controller amplifier. Each
tuner in the ST2 unit must be connected as a separate source for audio inputs.
CAT-5 Cable
ST2-KP Connections to ST2-XM Tuner (Non-RNET Systems)
The diagram depicts a standard ST2-KP keypad connection to the keypad port on the back of the
ST2-XM. The keypad uses a 110 punchdown connection and an RJ-45 T568A connection to the tuner.
11
ST2-XM SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
XM Antenna
XM Signal Strength Mode
Connect the included XM antenna for XM reception to the back panel of the XM module. The
antenna comes with 20 feet of cable. If this
length is not sufficient, there are aftermarket
antenna kits available for custom lengths.
Position the antenna near a south-facing window
to receive the best signal from a satellite or terrestrial signal.
To test the XM reception, turn the unit on. When
the XM radio is powered for the first time, the
XM service will start playing XM Channel 1, a
preview/promotional channel. Verify that Channel
1 is playing by pressing the Tune Up/Tune Down
buttons. Enter Signal Strength Mode by pressing
and holding the ST/MONO button on the ST2-XM
front panel. The display shows one of the following:
The antenna may also be attached to an external wall by sliding the slots on the back of the
antenna onto four screws mounted on an exterior wall. Establish the best receiving position for
the antenna before attaching it to the wall.
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Adjust the antenna until GOOD SIGNAL is displayed. Press ST/MONO to exit Signal Strength
Mode.
75 ohm
to 300 ohm
balun
25A
Connecting an Indoor and Outdoor Antenna
The diagram above depicts a typical setup using the ST2-XM Tuner with the included XM antenna, FM
antenna and AM loop antenna. Also shown are two outdoor antenna options (not included).
(Not to scale)
12
ST2-XM SETUP AND CONNECTIONS
ANTENNA CONNECTIONS
AM Antenna
FM Antenna
Connect the included loop antenna for AM reception to the back panel, attaching the GND
(ground) and AM ends to the appropriate connections for Tuner 2.
Attach the included FM antenna to the Tuner 2
FM COAX connection on the back panel by pushing the F-type quick-connect termination of the
antenna onto the FM connection.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best performance for AM reception. Use a 75-ohm to
300-ohm balun at the AM connection on the
tuner, and attach the 75-ohm coax cable to the
balun.
It is recommended to use an external outdoor or
attic-mounted long wire antenna for best performance for FM reception. Attach the desired
length of 75-ohm coax cable directly to the FM
connection on the tuner.
Antenna
Lead In Wire
Electric
Service
Equipment
Grounding
Conductors
Ground
Clamps
Power Service
Grounding
Electrode System
Grounding an Outdoor Antenna
If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges
and voltage surges. Consult the instructions that came with the antenna or contact the antenna manufacturer for proper installation instructions. The diagram gives a general depiction of how an outdoor
antenna should be grounded. For complete guidelines on antenna grounding procedures, please consult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984.
13
ST2-XM OPERATION
XM RADIO OVERVIEW
XM Radio Activation
XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depending on location) transferred by terrestrial antennas. The radio is a subscription-based service with a
monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but
will not broadcast the full range of channels without activation. Activation and billing are handled solely through XM Radio.
To activate the XM tuner:
1 Turn on the power, select the XM Tuner, and select channel 0. The tuner’s eight-character XM
satellite Radio ID number will appear on the display. Write the number down to have it available
when contacting XM Radio for activation. The number is also shown on the back of the unit and
on the product box.
2. To subscribe, have a major credit card and your XM Radio ID number at hand and contact XM at
http://www.xmradio.com/activation You can also activate service by calling XM Radio at
1-800-967-2346. You will be guided through the activation process step by step.
3. A complete and up-to-date full channel listing is available on the XM Radio website,
www.xmradio.com.
XM Radio Displays
In addition to Channel and Category information, the XM tuner will broadcast operating condition messages when the following conditions occur:
Display
ANTENNA
UPDATING
LOADING
OFF AIR
CH - - -----------
14
Condition
Antenna not connected
Updating encryption code
Acquiring channel audio or information
Channel not in service
Channel (SID) no longer available
Corresponding Artist Name or Song Title are null (empty)
No channel available for the chosen category
ST2-XM OPERATION
XM RADIO MODES
XM Radio Modes
There are four user “modes” for selecting music and viewing music information on the XM Tuner:
Preset (default or normal)
Category Search
Now Playing
Display Preferences.
These modes are accessed through certain button and key presses from the tuner panel, remote
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will
time out by showing EXIT and return to tuner display and Preset mode.
For all XM Modes
The chart below outlines the button presses for various XM tuner functions outside of the XM modes.
ST2-XM
ST2-RC
ST2-KP
UNO-S2
SRC2
All User Modes
Operating Mode Toggle
OK
Exit Current Mode
ST/
MONO
Signal Strength
Hold
Hold
Hold
Operating Mode Toggle
This button press accesses the three non-default XM modes. The three modes will appear in order:
Category Search, Now Playing and Display Preferences.
Exit Current Mode
This button press returns the XM tuner to Preset (default) mode.
Signal Strength
This button press and hold accesses the Signal Strength mode. Depending on the signal, the following will be displayed:
GOOD SIGNAL Signal strength good
MARGINAL SIG Signal strength marginal
POOR SIGNAL Signal strength poor
NO SIGNAL
Loss of signal
Press the appropriate button again to exit Signal Strength Mode.
15
ST2-XM OPERATION
XM RADIO MODES
Preset (default) Mode
This is the normal operating mode of the XM tuner. In this mode the XM tuner operates similarly to
the AM/FM tuner for channel up and down, bank selection and memory presets.
Next Preset
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.
Previous Preset
This button press accesses the previous saved preset in the chosen bank
Next Bank
This button press accesses the next bank (total of 6 banks).
Previous Bank
This button press accesses the previous bank.
Channel Up
This button press accesses the next active channel up from the current channel.
Channel Down
This button press accesses the next active channel down from the current channel.
ST2-XM
ST2-RC
ST2-KP
UNO-S2
SRC2
Preset Mode
Next Preset
MEM
MEM
Previous Preset
Next Bank
Hold
Hold
Hold
Previous Bank
Hold
Hold
Hold
Channel Up
Channel Down
16
TUNE
TUNE
ST2-XM OPERATION
XM RADIO MODES
1.CAT SEARCH)
Category Search Mode (1
XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is
a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this
mode is refined to scrolling only those channels in the selected category.
Next Category
This button press accesses the next category from the current category.
Previous Category
This button press accesses the previous category from the current category.
Category Channel Up
This button press accesses the next channel up within the selected category.
Category Channel Down
This button press accesses the next channel down within the selected category.
ST2-XM
Category Search Mode
Next Category
ST2-RC
ST2-KP
UNO-S2
SRC2
OK
MEM
MEM
Previous Category
Category Channel Up
TUNE
Category Channel Down
TUNE
17
ST2-XM OPERATION
XM RADIO MODES
2.NOW PLAYNG)
Now Playing Mode (2
This mode displays information about the current XM selection. Appropriate button presses access
the next or previous information item.
NAME:
Displays the artist’s name, feature name or program name (news, talk, sports).
TITLE :
Displays the song title or program title.
CATEGORY :
Displays the current category.
ST2-XM
Now Playing Mode
Next Info Item
ST2-RC
ST2-KP
UNO-S2
SRC2
OK
MEM
TUNE
MEM
TUNE
Previous Info Item
3.DSPLY PREF)
Display Preference Mode (3
This mode allows you to choose how XM channel information will be displayed on the keypad and
tuner. Appropriate button presses access the next or previous preference item.
Note: For any display configuration, the artist’s name and song title will scroll before the display
returns to the designated display format.
CH NUMBER:)
Channel Number (C
This selection displays the channel number only (e.g., XM070, XM103).
CH NAME:)
Channel Name (C
This selection displays the channel name only (e.g., ESPN Radio, Real Jazz).
#:CH NAME:)
Channel Number and Name (#
This selection displays the channel number and name (e.g., 64:The Groove, 121:Fox News).
ST2-XM
Display Preference Mode
ST2-RC
OK
Next Display Preference
MEM
TUNE
MEM
Previous Display Preference
18
TUNE
ST2-KP
UNO-S2
SRC2
ST2-XM OPERATION
FRONT PANEL CONTROLS
Front Panel Operation
Turning the unit on
To turn the unit on, push the On/Off button up on the
front panel. Pushing the On/Off button down turns the
tuner off.
Selecting the desired tuner
From the front panel, use
to toggle between XM
and AM/FM. A backlight shows behind the selected
label XM (green) or AM/FM (amber) to indicate the
active tuner. In addition, the LCD panel is also backlit
green for Tuner 1 and amber for Tuner 2. Each time a
tuner is selected the display will refresh with the current station or preset, and all subsequent memory
preset entries will be associated with that selected
tuner.
screen when selecting mode. Normal operation is in
Distant mode. In cities, antennas can pick up multipath signals when they bounce off buildings and get
doubled. The Local mode limits the noise associated
with these reflected signals.
Bank/Memory Presets
Each tuner has six banks of preset memory settings,
and each bank holds six presets for a total of 36 possible presets for each tuner (72 total presets).
Presets are associated with the tuner that is selected
at the time the preset is saved.
Memory Preset programming
From the front panel, perform these steps:
1. Select a tuner using
.
Selecting the desired band (AM/FM only)
2. Use
Push
3. If AM/FM, select the desired band using
to switch between AM and FM reception.
to choose from one of six banks (1-6).
.
Selecting a mode (XM)
4. Tune to the desired station or channel.
Push
Signal Strength mode (XM)
5. Push the desired memory preset (M1 through M6)
button for more than 2 seconds. When the memory
preset is saved, the appropriate preset number (M1
through M6) and SAVED appears on the LCD. The
selected station setting reappears and the sound
resumes after the button is released.
Press and hold
Recalling a Memory Preset
to select an XM operating mode.
Exiting a mode (XM)
Push
to exit the XM mode selection menu.
and release. The display shows
the signal strength rating. To exit press
.
Selecting the desired frequency or channel
Press and release
and
for manual tuning.
Selecting Stereo or Mono Output (AM/FM
only)
Press and release
to toggle between stereo and
mono mode. STEREO or MONO appears briefly on the
screen when selecting mode.
Selecting Distant or Local Reception
(AM/FM only)
Press and hold
to toggle between distant and
local mode. DISTANT or LOCAL appears briefly on the
To recall a memory preset, use
to select the
desired bank, then press the desired preset button
(M1 to M6). In addition to direct selection, the memory presets can be accessed by using
and
scroll through all presets for the bank selected.
to
Backup and Restore
Once all of the tuner settings are completed, it may
be advisable to create a backup of the programmed
settings for future use. The backup will then be available in case tuner settings need to be restored. The
“RNET Backup Utility” is available through the
Document Center at www.russound.com. Also
required are a DB9 male-to-female cable and laptop
or desktop PC.
19
ST2-XM OPERATION
ST2-RC REMOTE CONTROL
ST2-RC Remote Control Operation
Frequency Seek (AM/FM only)
The ST2-RC remote control is the only means of
remote operation of the ST2-XM in a non--RNET system. The ST2-XM front panel displays information for
the tuner that is receiving commands from the ST2RC. However, the ST2-RC commands do not change
which tuner is playing; that is done through the system’s source selection.
The SEEK function is performed by pressing and
Turning the unit on/off
To switch the ST2 tuner in or out of standby mode,
PWR
push
TUNER 2.
Selecting Stereo or Mono Output
(AM/FM only)
ST/
MONO
TUNER 1
TUNER 2
To control a tuner, push
or
. When
pressed, these buttons will be backlit green for Tuner
1 (XM) and amber for Tuner 2 (AM/FM). Each time a
tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will
be associated with that selected tuner.
Selecting the desired band (AM/FM only)
AM/FM
station. Pushing
continues the SEEK function.
Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency.
or any other button except TUNER 1 or
Selecting the desired tuner
Push
releasing
to seek lower frequencies or
for
higher frequencies. SEEK tuning begins at the current
frequency, seeks upward and stops at the next tuned
to switch between AM and FM reception.
Selecting the desired frequency or channel
Press
to toggle between stereo and mono mode.
STEREO or MONO appears briefly on the screen when
selecting mode. Normal operation is in stereo mode.
On a preset, the stereo/mono setting is saved for
that preset.
Selecting Distant or Local Reception
(AM/FM only)
LOC/
DX
Press
to toggle between Distant and Local
mode. DISTANT or LOCAL appears briefly on the
screen when selecting mode. Normal operation is in
Distant mode.
Recalling a Memory Preset
To recall a memory preset, select the desired tuner,
TUNE
Use
and
for manual tuning. To move quickly
through the stations or channels, press and hold
either of the Tune buttons for more than 1.5 seconds.
TUNE
press
BANK
and enter the desired bank number
MEM
(1-6), then press
and enter the desired preset
number (1 to 6). The memory presets can also be
MEM
TUNE
To directly select a station or channel, press
,
and enter the two- or three-digit XM channel number,
or the three- or four-digit station frequency (1071 for
107.1, etc.). European regions use five-digit station
frequencies.
Selecting a mode (XM)
Push
OK
to select an XM operating mode.
Exiting a mode (XM)
Push
menu.
20
ST/
MONO
to exit the XM operating mode selection
accessed by using
and
presets for the selected bank.
MEM
to scroll through all
Saving Favorites
The remote control stores two “favorites” (similar to
memory presets) per tuner. These are set simply by
selecting either Tuner 1 or Tuner 2, setting the
desired frequency and pressing and holding
FAV 2
FAV 1
or
until “FAV1 (2) saved” appears on the tuner.
Stored Favorites are then recalled by pressing either
FAV 1
or
FAV 2
.
ST2-XM OPERATION
ST2-KP KEYPAD CONTROL
ST2-KP Keypad Operation
1
4
Turning the keypad on/off
To activate the ST2-KP, press
. Press
to
power down the keypad display. The keypad remains
powered until the ST2-XM Tuner is turned off.
1
Push
2
Push
2
and hold
or
to select the desired bank. The
bank name will show on the display.
4
Selecting the desired tuner
To select a different tuner, press and hold
. (If the
keypad has been hardware jumper-selected to Tuner
1 or Tuner 2, it will not switch between the two
tuners.) The backlight color of the display will be
green for Tuner 1 (XM) and amber for Tuner 2
(AM/FM). Each time a tuner is selected the display
will refresh with the current station or preset for that
tuner, and all subsequent button presses and memory preset entries will be associated with that selected
tuner.
2
Selecting a Bank
To select a bank, select the desired tuner, then press
Recalling a Memory Preset
To recall a memory preset, press and release
or
to scroll through the presets for the selected
bank. (Memory presets must be stored for ST2-KP
recall)
5
ST2-KP Keypad Display
The 5-character backlit display shows frequency and
band, plus XM channel and mode information.
Messages scroll twice, then display the first 5 characters.
Selecting the desired band (AM/FM)
to switch between AM or FM band.
ST2-KP Keypad-Front Panel
Selecting a mode (XM)
to select an XM operating mode.
Exiting a mode (XM)
5
Press and release
until EXIT is displayed to exit
the XM operating mode menu.
3
Selecting the desired frequency or
channel
3
2
Use
and
for manual tuning. To move quickly
through the channels, press and hold either
3
or
for more than 1.5 seconds. European frequencies show in .05 MHz increments.
4
1
21
ST2-XM OPERATION
UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER
UNO-S2 Keypad Operation
Frequency Seek (AM/FM only)
NOTE: To control the ST2 Tuner through the
UNO-S2 keypad, the tuner must be configured
as a source using the controller’s programming
steps.
A press on
Turning the unit on
Frequency Scan (AM/FM only)
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the UNO-S2 keypad will
bring the tuner out of standby mode.
To scan, press and hold then release
Selecting the desired tuner
On the UNO-S2 keypad, press
choosing the source name/number associated
Selecting the desired band (AM/FM only)
to toggle between AM band and FM
Selecting a Mode (XM)
to toggle between XM modes.
Exiting a Mode (XM)
, EXIT is displayed to exit
XM mode selection menu.
. The
ond preview before moving to the next station.
again.
Signal Strength Mode (XM)
To check XM signal strength, press and hold
strength rating. To exit, press
again.
Selecting a Bank
up or
for bank
for bank down. The bank’s name will
be temporarily displayed on the UNO-S2.
Recalling a Memory Preset
Press
and
to scroll through the memo-
ry presets for the selected bank. This procedure
will step through all of the presets in the current
Selecting the desired frequency or channel
bank, then loop back to start at the first one.
Use
Only configured presets will be displayed.
and
for manual tuning or channel
selection. The frequency or channel will appear
on the keypad and the active tuner. To move
quickly through the channels, press and hold
either
22
again.
tuner scans through tuned stations with a 5-sec-
To select a bank, press and hold
band reception.
Press and release
end the SEEK function by pressing
then release. The display shows the signal
with Tuner 1 or 2.
Push
able station. If a tuneable station is not found,
To end scanning, press
to select
either Tuner 1 (XM) or Tuner 2 (AM/FM) by
Push
will seek the next higher tune-
or
for more than 1.5 seconds.
Mute
Press
to mute/unmute the tuner audio output.
ST2-XM OPERATION
UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER
1
6
5
2
4
3
1
2
TUNER SELECTION - Select source name/number associated with TUNER 1 (XM) or TUNER 2
(AM/FM)
TUNE UP/DOWN - Used for manual station or
channel selection
3
4
SELECT (AM/FM) Selects AM or FM band
(XM) Operating mode toggle
SEEK - (press)
(AM/FM) Seeks next higher tuned station
(XM) Exit current XM mode
4
SCAN - (press and hold)
(AM/FM) Scans through tuned stations with
5-second preview before next station
(XM) Signal Strength mode toggle
5
MUTE - Mutes/unmutes tuner audio output
6
BANK SELECT - Used for bank selection (press
and hold)
6
MEM UP/DOWN - Scrolls through memory preset stations (press)
NOTE: UNO-S2 keypads are connected to the
controller to control the ST2-XM through RNET.
UNO-S2 keypads do not connect directly to
the ST2 Tuner.
23
ST2-XM OPERATION
SRC2 REMOTE CONTROL WITH RNET CONTROLLER
SRC2 Remote Control Operation
(1071 for 107.1, etc.). European regions use five-
Turning the unit on
digit station frequencies.
The tuner is power managed by the CAV6.6 or other
RNET-enabled controller. If the tuner is in standby
mode, any button press of the SRC2 will bring the
tuner out of standby mode when used with the UNO
keypad.
Selecting the desired tuner
To select a tuner, push
Frequency Seek (AM/FM only)
The SEEK function is performed by pressing and
releasing the Select
or
higher frequency station press
and choose the source
. To seek
. Press
for
lower frequencies. Tuning begins at the current fre-
name/number associated with Tuner 1 (XM) or Tuner
quency, seeks upward (or downward) and stops at the
2 (AM/FM), or use the numeric source inputs at the
next tuned station. Pushing
bottom of the SRC2.
tinues the SEEK function. Once the highest frequency
Selecting the desired band (AM/FM only)
is reached, the tuner continues SEEK mode at the
Push
lowest frequency.
to toggle between AM/FM reception.
or
Selecting a Mode (XM)
Frequency Scan (AM/FM only)
Push
To scan, press and hold then release
,
ating modes.
or
to toggle between XM oper-
Press
again con-
. The
tuner scans through tuned stations with a 5-second
preview before moving to the next station. To end
Exiting a Mode (XM)
to exit XM operating mode menu.
scanning, press
again.
Signal Strength Mode (XM)
Selecting a Bank
Press and hold
To select a bank, press and hold
and release. The display shows
the signal strength rating. To exit press
.
or
Recalling a Memory Preset
Use the Channel
Press
and
or
and
channels, press and hold the button for more than
for bank up
for bank down.
Selecting the desired frequency or channel
for manual tuning. To move quickly through the
and
to scroll through a loop of all
the memory presets for the currently selected bank.
Only configured presets will be displayed.
1.5 seconds. To directly select a station or channel,
Mute
enter the three- or four-digit channel or frequency
Press the
audio output.
24
or
button to mute/unmute the tuner
ST2-XM OPERATION
SRC2 REMOTE CONTROL WITH RNET CONTROLLER
RUSSOUND SELECTION - “R” must be
the selected source for control of the
controller and any connected components. Select “R” before sending
SRC2 remote commands.
1
1
POWER - Power managed by controller
2
NUMERIC INPUT - (press) Number buttons for direct
input of frequency or channel
2
MEMORY PRESETS - (press and hold) Number buttons
(1-6) for saving memory presets
3
LAST - Recalls last XM channel selected
4
INFO - XM Now Playing mode toggle
5
TUNE UP/DOWN - Incrementally scrolls through channels or tuned stations
6
OK - Confirms numeric selection. XM Operating mode
toggle
7
EXIT - Exit XM operating mode
8
PLAY - Selects AM or FM band. XM Operating mode
toggle
9
SCAN - (press and hold) Scans through tuned AM/FM
stations with 5-second preview before next station.
(press) Exit XM operating mode
2
17
3
16
15
4
10 BANK UP/DOWN - (press and hold) Scrolls through banks
5
10 MEM UP/DOWN - (press) Scrolls through memory presets for selected bank
14
6
13
12
5
11 TUNER SELECTION - Select XM or AM/FM Tuner by its
associated source name/number
7
12 PAUSE - Mutes/unmutes tuner audio output
8
13 GUIDE - XM Category Search mode toggle
9
14 SEEK UP/DOWN - Seeks next tuned AM/FM station up
or down. XM - Next/previous preset,
category, info item, display preference
15 MENU - XM Operating mode toggle
11
10
16 TUNE UP/DOWN - Incrementally scrolls through
channels or tuned stations
17 TUNER SELECTION - Select XM or AM/FM Tuner by its
associated source name/number (scrolling through
sources until reached)
25
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
ST2-XM Tuner Setup Menus
Note: The Setup Menu procedures must be performed from the ST2-XM Tuner front panel.
The ST2-XM Tuner Setup Menus provide setup and naming procedures for the ST2-XM main chassis,
the XM tuner module and the AM/FM tuner module. These procedures include source number assignments, assigning a custom name to a memory preset or a bank, choosing a region for AM/FM operation (US or Euro), factory initialization and system information.
If the ST2-XM is used with a non-RNET system, the ST2-XM can be connected and operated without
any setup programming. Follow the setup menus if custom names are desired, or for system info.
If the ST2-XM is used with an RNET system such as CAV6.6, the following minimum setup must be
performed for the ST2-XM to be properly controlled by the CAV6.6:
1. ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.
2. RNET Controller Source Setup Menu - Configure the source numbers assigned in step 1 for Tuners
1 and 2, and assign command type PERIPHERAL.
NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then to
the RNET controller (must be powered on last) to establish a connection.
ST2 Chassis Setup Menu
Source Number (Chassis)
The Source Number procedure permits Tuner 1
(XM) and Tuner 2 (AM/FM) to be assigned the
proper source numbers to be used in an RNET
system.
Note: The source number must be assigned as
PERIPHERAL in the RNET controllers.
Note: Each of the ST2-XM modules can be configured as source number “unassigned” if the
module is used in another system (e.g., home
theater) or will not be used as a source in the
RNET system.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SOURCE NUM appears on the tuner.
3. Press BAND. TUNER # appears.
4. Press the Tune Up/Down buttons to select the
Tuner # (Tuner 1 is XM, Tuner 2 is AM/FM).
5. Press BAND. SOURCE NUM appears.
6. Press the Tune Up/Down buttons to scroll
26
through the source numbers 1-6.
7. Press BAND to select the source number.
8. Repeat the process for the next tuner.
9. Press TNR SEL to exit the Source Number
menu.
Update Firmware (Chassis)
The Update Firmware procedure allows the ST2
tuner’s OS firmware to be updated. The procedure is performed using a DB9 serial cable with
one end connected to the RS-232 port on the
back of the tuner and the other connected to a
PC or laptop. If an OS firmware update is available, it can be obtained through the Document
Center at www.russound.com. XM tuner module
firmware update must be performed by an
authorized Russound service facility.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until UPDATE FIRMW appears on the tuner.
3. Press BAND to enter the UPDATE FIRMW menu.
4. “Hold BAND” appears on the tuner.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Press and Hold
TNR SEL button
TNR
SEL
ST2 Chassis Setup Procedures
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
TNR
SEL
TUNER
#
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
HOLD
BAND
This
Procedure
returns the
ST2 Tuner
to its
Factory
settings
After update
cycle Power
Are you sure
SOURCE
NUM
Start
Update
YES
NO
Cycle Power
Please wait
Cycle Power
5. While pressing and holding BAND, “After
update cycle power” appears on the tuner
display.
6. When “Start Update” appears on the tuner display, start the update program. “Finished” will
then appear in firmware’s update window on the PC.
7. Cycle power to the tuner.
Factory Initialization (Chassis)
The Factory Initialization procedure allows the
erasure of all programmed settings and returns
them to the factory default settings.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until FACTORY INIT appears on the tuner.
3. Press BAND to enter the FACTORY INIT menu.
4. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
selections.
5. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
6. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when complete.
7. Cycle power on the ST2-XM tuner.
27
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
System Info (Chassis)
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
Press
Press
Press
Press
Press
Press
Press
BAND.
BAND at “Build Time” to view.
MEM Up/Down to advance.
BAND at “Build Date” to view.
MEM Up/Down to advance.
BAND at “Version” to view.
TNR SEL to exit the System Info menu.
(END OF ST2 CHASSIS SETUP)
XM Setup Menu
Memory Name Procedure
Press TNR SEL
button to select
XM Tuner
TNR
SEL
3.
4.
5.
6.
7.
8.
9.
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
DIAGNOSTICS
Procedure
TNR
SEL
BANK #
MEMORY #
MEMORY
NAME
Selects
character
Selects
character
position
Repeat
for each
character
in name
28
SAVE
CHANGES?
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
XM
Setup
Menu
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Tuner Setup Menu for XM
It is important to select the desired tuner
(Tuner 1 for XM) using the TNR SEL button
BEFORE accessing the Tuner Setup Menus.
Memory Name (XM)
A memory preset must be created and saved
before it can be named (see page 19). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
XM Setup Menu
Bank Name Procedure
Press TNR SEL
button to select
XM Tuner
TNR
SEL
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND again.
3. MEMORY NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND to advance. Memory # appears.
8. Press the Tune Up/Down buttons to select a
Memory #.
(continued)
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
DIAGNOSTICS
Procedure
BANK
NAME
SAVE
CHANGES?
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
XM
Setup
Menu
TNR
SEL
BANK #
Selects
character
Selects
character
position
Repeat
for each
character
in name
29
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Memory Name (XM) (continued)
9. Press BAND to advance. MEMORY NAME
appears again.
10. Press BAND to access the Memory Name
entry screen.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character
position. Up to 12 characters can be entered
one by one. A blinking cursor indicates the placement of the character being entered.
12. Press BAND when memory name is entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press BAND to save memory name. The
Memory Name menu returns to the Memory #
prompt to name other presets, or press TNR
SEL to return to the Memory Name menu start.
Bank Name (XM)
A custom name can be assigned to each of the
six banks of Tuner 1 (XM).
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND. BANK NAME appears again.
8. Press BAND to access the Bank Name entry
screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character position. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
10. Press BAND when bank name is entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press BAND to save bank name. The Bank
30
Name menu returns to the Bank # prompt to
name other banks, or press TNR SEL to exit the
Bank Name menu.
Controller ID (XM)
The Controller ID procedure is used to identify
the controller(s) that the XM tuner will
respond to.
Note: For the XM module that is installed in the
ST2-XM chassis, “All Controllers” will be the
default setting.
Diagnostics (XM)
The Diagnostics procedure is for factory
use only.
Factory Initialization (XM)
The Factory Initialization procedure allows the
erasure of all programmed settings of the XM
tuner and returns them to the factory default settings.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until FACTORY INIT appears on the
tuner.
4. Press BAND to enter the FACTORY INIT menu.
5. “Are you sure” appears on the tuner. Using the
Tune Up/Down buttons, view the “Yes” and “No”
selections.
6. Press BAND to select. A “No” selection
returns to the top of the Factory Init menu. A
“Yes” begins the initialization.
7. “Please wait” appears on the tuner during the
process and “Cycle Power” appears when complete.
8. Cycle power on the ST2-XM tuner.
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
System Info (XM)
(END OF XM TUNER SETUP)
The System Info menu shows the ST2 Tuner’s
manufacturing build properties.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press MEM Up/Down
until SYSTEM INFO appears on the tuner.
3. Press BAND.
4. Press BAND at “Build Time” to view.
5. Press MEM Up/Down to advance.
6. Press BAND at “Build Date” to view.
7. Press MEM Up/Down to advance.
8. Press BAND at “Version” to view.
9. Press TNR SEL to exit the System Info menu.
Press TNR SEL
button to select
XM Tuner
TNR
SEL
Tuner Setup Menu for AM/FM
It is important to select the desired tuner
(Tuner 2 for AM/FM) using the TNR SEL button BEFORE accessing the Tuner Setup
Menus.
Memory Name (AM/FM)
A memory preset must be created and saved
before it can be named (see page 19). Once it is
saved, the preset’s Tuner #, Bank # and Memory
# must be entered in the following procedure.
(continued)
XM Setup Menu
Controller, Diagnostics, Factory Initialization
and System Info Procedures
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
BANK
NAME
Procedure
CONTROLLR
ID
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
DIAGNOSTICS
Procedure
SYSTEM
INFO
Procedure
FACTORY
INIT
Procedure
XM
Setup
Menu
TNR
SEL
All Contrlrs
This
Procedure
is for
Factory
use
ONLY
This
Procedure
returns the
ST2 Tuner
to its
Factory
settings
Are you
sure?
Yes or No
YES
NO
Please
Wait
Cycle Power
31
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Memory Name (AM/FM) (continued)
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND again.
3. MEMORY NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
7. Press BAND to advance.
8. Press the Tune Up/Down buttons to select a
Memory #.
9. Press BAND to advance. MEMORY NAME
appears again.
10. Press BAND to access the Memory Name
entry screen.
11. Press Tune Up/Down to select a character
and MEM Up/Down to change a character position. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
12. Press BAND when memory name is entered.
13. SAVE CHANGES will appear.
14. Press Tune Up/Down to select Yes or No.
15. Press BAND to save memory name. The
Memory Name menu returns to the Memory #
prompt to name other presets, or press TNR
SEL to return to the Memory Name menu start.
Bank Name (AM/FM)
A custom name can be assigned to each of the
six banks of Tuner 2 (AM/FM).
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until BANK NAME appears on the tuner.
4. Press BAND.
5. Bank # appears.
6. Press the Tune Up/Down buttons to select the
Bank #.
32
7. Press BAND. BANK NAME appears again.
8. Press BAND to access the Bank Name entry
screen.
9. Press Tune Up/Down to select a character
and MEM Up/Down to change a character position. Up to 12 characters can be entered one by
one. A blinking cursor indicates the placement of
the character being entered.
10. Press BAND when bank name is entered.
11. SAVE CHANGES will appear.
12. Press Tune Up/Down to select Yes or No.
13. Press BAND to save bank name. The Bank
Name menu returns to the Bank # prompt to
name other banks, or press TNR SEL to exit the
Bank Name menu.
Region (AM/FM)
The Region procedure assigns either US or Euro
to the tuner. The difference between the two is
that US FM frequencies operate in .2 MHz increments, while European FM frequencies operate in
.05 MHz increments.
1. Enter the Setup Menu by pressing and holding
the TNR SEL button.
2. TUNER SETUP appears. Press BAND.
3. MEMORY NAME appears. Press MEM
Up/Down until REGION appears on the tuner.
4. Press BAND.
5. Press the Tune Up/Down buttons to select
either US or EURO.
6. Press BAND to select. Press TNR SEL to exit
the REGION menu.
(END OF AM/FM TUNER SETUP)
ST2-XM TUNER PROGRAMMING
ST2 TUNER SETUP MENU
Backup and Restore
Once all of the tuner settings are completed, it
may be advisable to create a backup of the programmed settings for future use. The backup will
then be available in case tuner settings need to
be restored.
Press TNR SEL
button to select
AM/FM Tuner
TNR
SEL
The backup and restore PC application “RNET
Backup” is available through the Document
Center at www.russound.com. Also required are
a DB9 male-to-female cable and laptop or desktop PC.
AM/FM Setup Menu
TNR
SEL
TUNER
SETUP
Menu
SOURCE
NUM
Procedure
UPDATE
FIRMW
Procedure
FACTORY
INIT
Procedure
SYSTEM
INFO
Procedure
Chassis
Setup
Menu
TNR
SEL
MEM
NAME
Procedure
REGION
Procedure
BANK
NAME
Procedure
AM/FM
Setup
Menu
TNR
SEL
TNR
SEL
BANK #
MEMORY #
MEMORY
NAME
BANK #
BANK
NAME
SAVE
CHANGES?
Selects
character
Selects
character
position
Repeat
for each
character
in name
Selects
character
Selects
character
position
Repeat
for each
character
in name
SAVE
CHANGES?
33
ST2-XM TUNER PROGRAMMING
PROGRAMMING RNET CONTROLLER
To Program the RNET Controller to operate with the ST2-XM Tuner:
(refer to the controller’s Instruction Manual for details)
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.
2. SOURCE SETUP will appear. If programming a CAM6.6, press the Next button once for Source
Setup. Enter the Source Setup Menu by pressing the Play button on the UNO-S2 keypad.
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (XM)
is connected. Press the Play button to enter your choice.
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1
or XM). Press the Play button to enter your choice.
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this
choice.
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.
9. Press the Setup button three times to back out of the Installation Menu.
Source Configuration Note:
When the ST2-XM Tuner is used with the CAV6.6 or other RNET controller, it is configured as an
RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave
as a fully integrated device with UNO keypad support. Each tuner must be set up with a unique
source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.
Key Function Note:
When using the tuner with an RNET system, do not reassign keypad and remote buttons for tuner
control in the controller’s Key Configuration Menu. When the tuner is assigned the “Peripheral” command type in the controller’s Setup Menu, key assignments and functions are automatically assigned
and will operate as shown in the preceding UNO-S2 keypad and SRC2 remote diagrams.
34
TECHNICAL SPECIFICATION
ST2-XM Smart Tuner
Dimensions:
Weight:
Power Supply:
Frequency Range:
17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)
7 lbs. (3.2kg)
12VDC 1.5A
AM 530 - 1710 kHz
FM 87.7 - 107.9 MHz
FM Antenna impedance:
Impedance:
75 ohm unbalanced
300 ohm balanced
AM
Sensitivity @ S/N:
Image rejection:
S/N ratio:
20dB 55 dBu
33dB
45 dB
FM
Sensitivity @ S/N:
30 dB 6dB max 12 dBu
Image rejection:
80 dB
S/N ratio:
60 dB
XM
XM Band:
XM Antenna:
2332.5 - 2345 MHz
50-ohm SMB connection
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology
incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE®
voice compression software included in this product is protected by intellectual property rights
including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this
or any other software contained in an XM radio is explicitly prohibited from attempting to copy,
decompile, reverse engineer, or disassemble the object code, or in any way convert the object code
into human-readable form. The software is licensed solely for use within this product.
35
WARRANTY & REPAIR
The Russound ST2-XM is fully guaranteed against all defects in materials and workmanship for two
(2) years from the date of purchase. During this period, Russound will replace any defective parts and
correct any defect in workmanship without charge for either parts or labor.
For this warranty to apply, the unit must be installed and used according to its written instructions. If
service is necessary, it must be performed by Russound. The unit must be returned to Russound at
the owner's expense and with prior written permission. Accidental damage and shipping damage are
not considered defects, nor is damage resulting from abuse or from servicing by an agency or person not specifically authorized in writing by Russound.
This Warranty does not cover:
• Damage caused by abuse, accident, misuse, negligence,
or improper installation or operation
• Power surges and lightning strikes
• Normal wear and maintenance
• Products that have been altered or modified
• Any product whose identifying number, decal, serial number, etc.
has been altered, defaced or removed
Russound sells products only through authorized Dealers and Distributors to ensure that customers
obtain proper support and service. Any Russound product purchased from an unauthorized dealer or
other source, including retailers, mail order sellers and online sellers will not be honored or serviced
under existing Russound warranty policy. Any sale of products by an unauthorized source or other
manner not authorized by Russound shall void the warranty on the applicable product.
Damage to or destruction of components due to application of excessive power voids the warranty on
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and
labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with
a note explaining the nature of service required. Be sure to pack the unit in a corrugated container
with at least three (3) inches of resilient material to protect the unit from damage in transit.
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number.
Write this number on the shipping label and ship to:
Russound
ATTN: Service
5 Forbes Road
Newmarket, NH 03857
Due to continual efforts to improve product quality as new technology and techniques become available, Russound/FMP, Inc. reserves the right to revise system specifications without notice.
36
NOTES
37
NOTES
38
NOTES
39
Russound
5 Forbes Road, Newmarket, NH 03857
tel 603.659.5170 • fax 603.659.5388
e-mail: tech@russound.com
www.russound.com
E. & O.E.
28-1160 Rev. 3 02/07/06
Copyright © 2004-2006 Russound® All rights reserved.
All trademarks are property of their respective owners.