Absco Highlander Shed

Assembly Instructions

Model: 30292H

FOR CONSTRUCTION IN

NON-CYCLONIC AREAS

WIND RATING: W33N (N2)

FRONT: 3.00m

SIDE: 2.92m

WALL HEIGHT: 2.035m

GABLE HEIGHT: 2.300m

3020mm

CONCRETE SLAB

3100mm

WHEN LAYING YOUR CONCRETE

SLAB, CHAMFER THE 50mm EDGES

DOWNWARDS BY 10mm.

50mm

10mm

50mm

THIS WILL ENSURE THAT

WATER RUN OFF IS KEPT

CLEAR FROM YOUR SHED

We thank you for choosing an Australian Made Shed. For further assistance please visit our detailed instructional video library at http://www.absco.com.au/videos.php

At ABSCO Industries we are always looking to be number ONE, so please let us know what you think of our instructions. Feedback makes us better.

[email protected].

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 1

Absco Highlander Shed - Model: 30292H

GENERAL INSTRUCTIONS

Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details.

Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on pages three to five.

SITE PREPARATION

The site for the shed must be level.

It is recommended that the shed be set on a concrete slab and anchored down appropriately (refer page 15 for details).

Anchor sets are not supplied as standard items with this product.

TOOLS REQUIRED

3mm

4mm

A NOTE ON SAFETY

Some parts may have sharp edges. It is advisable to wear gloves when handling these items and safety glasses if drilling holes. Sensible shoes are highly recommended.

OPTIONAL

Do not erect your shed in windy conditions, ensure that the shed is securely anchored to a solid foundation immediately after construction is completed.

It is highly recommended to erect the shed with two or more people.

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 2

Absco Highlander Shed - Model: 30292H

QTY

2

COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS

COMPONENT

DESCRIPTION

PART

No.

CHECK QTY

STEEL SHEET

2034mm X 773mm

H30 2

COMPONENT

DESCRIPTION

GABLE R/H

L=1475mm

PART

No.

CHECK

16R

6 STEEL SHEET

2034mm X 773mm

H31 4

BRACE

L: 393mm

13A

2

2

4

2

4

1

1

2

ABSCO INDUSTRIES

STEEL SHEET

1546mm X 773mm

44L

STEEL SHEET

1546mm X 773mm

44R

STEEL SHEET

1546mm X 773mm

45A

STEEL SHEET

2034mm X 711mm

H34

STEEL SHEET

2034mm X 731mm

HRC

STEEL SHEET

1974mm X 773mm

F

STEEL SHEET

1974mm X 773mm

E

GABLE L/H

L=1475mm

16L

1

CHANNEL

L = 2993mm

1

CHANNEL

L = 2993mm

1

CHANNEL

L = 2993mm

1

CHANNEL

L = 2993mm

2

CHANNEL

L = 2993mm

2

CHANNEL

L = 2919mm

2

CHANNEL

L = 2919mm

2

CHANNEL

L = 1568mm

ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10

77A

55C

77B

81B

81A

59A

81G

78A

PAGE 3

2

Absco Highlander Shed - Model: 30292H

COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS

QTY

COMPONENT

DESCRIPTION

PART

No.

CHECK QTY

COMPONENT

DESCRIPTION

PART

No.

CHECK

1

CHANNEL

L = 1568mm

79A

2

CHANNEL WITH HINGES

L = 1974mm

HC1

2

1

JAMB L= 2034mm

JAMB L= 1568mm

HJ1

90A

1

CHANNEL

L = 1974mm

HC2 4

JAMB L= 1120mm

4

CHANNEL

L = 773mm

1

58C 1

JAMB L= 1974mm

RIDGE

BEAM

97A

4

L = 2993mm

LIP TRIM L= 1546mm

CONTENTS OF FITTINGS PACKET

220 3 DOOR

PADBOLT

8

12

1

SELF TAPPING

SCREWS

4mm NUT & BOLT SET

SECURE TWO

PADBOLTS TO DOOR

SHEET

4mm CSK SCREW &

NUT SECURE HINGES

TO DOOR

ASSEMBLY

INSTRUCTIONS

2

18

2

DOOR

PADBOLT

HASP

91A

HJ3

87B

3mm POP RIVETS SECURE

HINGES TO DOOR

(ALTERNATIVE FIXING

METHOD)

DOOR

STRAP

L: 165mm

12A

22A

CAP GABLE

L: 170mm

14A

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 4

Absco Highlander Shed - Model: 30292H

ABSCO ASSEMBLY INTRODUCTION

The snap-tite assembly system locks all perimeter channels to all roof and wall sheets without the need for tools and fasteners .

To pre-assemble the four wall panels and two roof panels, the perimeter channels are secured to the top and bottom of each panel using the snaptite system, as detailed on the following pages wherever you see the symbol.

SNAP i

HIGH SIDE

PUSH

After joining sheets together, position channel over one end of the sheets, gently tapping it over the snaptite lugs, working along the sheets to the other end.

PUSH

Position sheets on timbers, trestles or partly over edge of concrete slab.

FASTENING SYMBOLS

HIGH SIDE

Join components together with one screw at this location only, as some channel sections have extra holes that are not required for this model of garden shed

Do not join components together at this location yet, as the screw may obstruct further assembly of other components

ABSCO INDUSTRIES

Each perimeter channel must finish flush with the edges of the sheets. the snap-tite system allows adjustment for this process by simply tapping the channel along the sheets until each end is neatly flush.

ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10

3mm POP RIVETS

4mm NUT & BOLT SET

PAGE 7

Absco Highlander Shed - Model: 30292H

DOOR PANEL ASSEMBLY

58C

58C

HC1

F

12A

E

58C

HC2

HC1

58C

HJ3

F

E

20mm FLANGE

15mm FLANGE

ABSCO INDUSTRIES

FOUR HOLE SET

FOR PADBOLT

CONNECTION

ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 8

Absco Highlander Shed - Model: 30292H

REAR PANEL ASSEMBLY

H30

H31

77B

H31

H30

81B

SIDE PANEL ASSEMBLY

(2 Required)

H31

H31

SMALL PAN

SMALL PAN

59A

81G

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 9

Absco Highlander Shed - Model: 30292H

ROOF PANEL ASSEMBLY

(2 Required)

44R

45A

45A

44L

87B

2 x PRE-PUNCHED

HOLES TO THIS

END OF EACH

SHEET WITH PART

NO. 81A FITTED

78A

81A

87B

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 10

Absco Highlander Shed - Model: 30292H

FRONT PANEL ASSEMBLY HJ1

H34

HJ1

H34

77A

90A

79A

55C

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 11

Absco Highlander Shed - Model: 30292H

DOOR PANEL ASSEMBLY

91A

91A

NOTE: Nuts and bolts (supplied) may be used instead of pop rivets (supplied) by simply enlarging the hinge hole sets in the jamb using a 4mm drill bit

E

F

NOTE: The two holes required to connect the padbolt hasp for each door have not been pre-punched, to allow for proper alignment. position each hasp centrally over the padbolt shaft, and drill 3mm holes and secure with screws

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 12

Absco Highlander Shed - Model: 30292H

PANEL CONSTRUCTION

NOTE: Take care to ensure that both front and rear wall panels are not positioned upside down. the top channel of each panel is pre-punched for attaching roof sheets, the bottom channels are not.

SIDE WALL PANEL CHANNELS

FIT INTO THE NOTCHED

FRONT AND REAR WALL

PANEL CHANNELS

97A

CHANNEL TYPE 78A

THIS END

CHANNEL TYPE

81A THIS END

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 13

Absco Highlander Shed - Model: 30292H

ROOF CONSTRUCTION

OUTSIDE VIEW

ROOR OVERHANGS

ALL WALL PANELS

BY 37mm

37mm

INSIDE VIEW

SECURE RIDGE BEAM TO

GABLE SECTIONS WITH

TWO SCREWS AT EACH

END. SECURE EACH ROOF

PANEL WITH ONE SCREW

IN EACH CORNER ONLY

AT THIS STAGE

ABSCO INDUSTRIES

2 X GABLE

BRACE

(13A)

AFTER THE ROOF PANELS

HAVE BEEN SECURED, FIT

TWO GABLE BRACES (13A)

FROM THE TOP WALL

CHANNEL TO THE UNDERSIDE

OF THE RIDGE BEAM AT 45

DEGREES AS SHOWN TO

BOTH GABLE WALLS.

INSIDE VIEW

ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10 PAGE 14

Absco Highlander Shed - Model: 30292H

FINAL CONSTRUCTION

14A

BEND THE TOP AND

BOTTOM FLANGES AS

SHOWN, THEN HOOK THE

BOTTOM FLANGES UNDER

THE TOP CHANNEL AND

SCREW THE TOP FLANGES

FOR BOTH AS SHOWN

GABLE CAPS

ANCHORING OF SHED

LOCATION OF 12

CONCRETE ANCHORS

BOLT & NUT WALL

SHEET

- EACH ANCHOR CONSISTS OF ONE NUT, BOLT,

DYNABOLT AND STEEL ANGLE

- DRILL A 10mm HOLE INTO

THE WALL SHEET

- DRILL A 10mm HOLE INTO THE

CONCRETE

ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 30292H 26/11/10

STEEL

ANGLE

SLAB

DYNABOLT

PAGE 15

PRODUCT WARRANTY

Congratulations on your purchase of an ABSCO Product.

ABSCO SHEDS are made using high quality Bluescope™ Australian made Zincalume™ or

Colorbond Steel™.

We are pleased to advise we warrant that this steel will not rust, crack, flake peel or blister for

20 years from date of purchase.

This warranty does not apply to surface deterioration of panels caused by ‘Swarf” (Tiny particles of steel debris left from cutting, grinding or drilling operations) that has not been removed after building construction, or as a result of contact with damp soil, chemicals, fertilisers or other corrosive substances.

This warranty covers any shed used for normal domestic use and installed in accordance with the installation instructions. The warranty does NOT cover Damage caused by storms, wind, rain snow or poor foundations.

This warranty does NOT cover ABSCO products installed in severe coastal, industrial or other highly corrosive environments. The warranty does not cover fasteners (screws, nuts, bolts, rivets, hasps or bolts).

The warranty is limited to replacement and delivery of components and does not include any labour or installation costs.

The warranty applies to the exclusion of all other representations, guarantees or warranties express or implied, our goods come with guarantees that cannot be excluded under the

Australian consumer law and is not transferable

For further information go to http://www.consumerlaw.gov.au.

Please retain a proof of purchase (sales docket or invoice) or register your warranty within 30 days of purchase here: www.absco.com.au/register_warranty.php

In the unlikely event a warranty claim is made it must be supported by photographic evidence together with proof of purchase documentation (or on-line registration of purchase) and forwarded to ABSCO INDUSTRIES, PO BOX 119 ACACIA RIDGE QLD AUSTRALIA 4110

Issued January 2011

ABSCO STEEL BUILDINGS- STORAGE GUIDELINES

ABSCO steel buildings include garden sheds, storage units, aviaries, garages and carports.

ABSCO steel buildings are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.

Other weather conditions such as extreme heat and extreme cold, moist or dry air can influence the effects of concrete floor moisture and/or condensation on the underside of the roof sheets.

ABSCO SHEDS and storage units are primarily used for storage of garden equipment such as lawnmowers, wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions may require additional protection such as being sealed or covered by plastic sheets and/or stacked above the concrete floor on timber slats.

Waterproof sealants may be used to offer further protection where required around joins and screw fixings, as can rubber door seals and other products which are available from most hardware outlets.

Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting with water accumulating and being trapped inside the shed.

Absco accepts no responsibility for water entry, floor moisture, condensation or the condition of the Contents inside your Absco steel building arising from any of the pre-mentioned weather conditions.