Bosmere A305 Assembly Instructions

IMPORTANT - Assembly Instructions – USA

A. Before commencing assembly check parts in box with illustrations on components page and thoroughly read the assembly instructions. Suggestions regarding siting options can also be found at www.trimetals.co.uk.

B. In the unlikely event that this product has been delivered damaged, there are any parts not included or you are having difficulties with assembly please contact Bosmere Inc,

North Carolina, [email protected].

DO NOT CONTACT THE RETAILER. Bosmere Inc will endeavour to correct any problems as quickly as possible.

C. A firm, level and flat surface is required as a base for the product. The product must be secured / anchored to a hard base (e.g., concrete or paving slabs). The product may not function properly if the base is not flat and level.

D. Do not assemble in windy conditions. If weather conditions change during assembly it is recommended that you stop and make the unfinished construction safe by temporarily anchoring the assembled parts to the base until conditions improve. This is to avoid personal injury to yourself or others and to protect the product panels from damage.

E. Extra care should be taken to avoid cuts and abrasions from exposed edges during assembly. We strongly recommend the use of protective gloves, heavy duty long sleeved clothing and protective glasses.

F. We recommend that two adults work on the assembly. Children should not assist with the assembly of the product and should be kept clear of the area when assembling the product.

G. We recommend that this product be only used by adults.

H. Precautions should be taken when the products are being used in exposed areas subject to high wind speeds. Care should be taken when they are opened to avoid damage.

I. Do not locate the product where accumulations of water, snow or ice may drop on it from a height.

J. It is your responsibility, to contact the local authorities to enquire if planning permission is required.

K. For additional weatherproofing we recommend the use of a mastic type sealant that can be used to create a seal between panels, as well as the product and the ground.

GA: 4390813_1

L. Retain these instructions after assembly is completed.

Care and Maintenance

A.

B.

Never climb on the roof or lean items against the product.

Our products are not intended for habitation and must not be used in this way.

C. Do not store items inside the product which are sensitive to humidity or variance in temperature.

D. Do not place or store any hazardous materials inside the product.

E. The roof must be kept clean and free from extra loads. Large amounts of accumulated snow may cause damage and could also make the structure dangerous to enter.

F. The product should be washed with water and a mild detergent every three months; if used in a coastal environment subject to salt conditions this should be increased to every month. Never use a pressure washer on the product.

G. basis.

We recommend that moving parts (including locks) be lubricated on a six month

H. Regularly check your product for loose fasteners (screws, bolts and nuts, etc.) and tighten them if required.

I. Any building, including the product, which is not insulated may be subject to condensation. To minimize this we would recommend that heavy duty polythene sheeting is placed under the base area to limit moisture rising from the ground; while the base must be flat and level always ensure that water drains away from the product area rather than into it. The use of polystyrene sheets adhered to the panels inside the product can be used as insulation if required.

J. All of our products are manufactured from metal and can therefore become hot if subjected to direct sunlight. If possible, place the product in locations which are not subject to long periods of direct sunlight.

2

GA: 4390813_1

Our disclaimers

It is your responsibility to determine whether you or your assembler have the necessary skill, knowledge and tools to properly and safely assemble the product described in these assembly instructions. Please note that improper assembly may cause risk to the personal safety and property of yourself and others.

SUBJECT ONLY TO TRIMETALS’ LIMITED PRODUCT WARRANTY-USA, WE DISCLAIM

ANY RESPONSIBILITY FOR ANY LOSS OR DAMAGE SUFFERED AS A RESULT OF THE

FAILURE TO STRICTLY FOLLOW THESE ASSEMBLY INSTRUCTIONS.

WE UNDERTAKE NO RESPONSIBILITY THAT THE PRODUCT WILL BE FIT FOR

PARTICULAR PURPOSE FOR WHICH YOU MAY BE BUYING THE PRODUCT.

THE PRODUCTS ARE INTENDED FOR DOMESTIC AND PRIVATE USE ONLY, AND WE

SHALL HAVE NO LIABILITY IN CONNECTION WITH USE OF THE PRODUCTS FOR

ANY COMMERCIAL, BUSINESS OR RE-SALE PURPOSE.

BY ASSEMBLING THE PRODUCT, YOU ACKNOWLEDGE THAT YOU UNDERSTAND

THESE DISCLAIMERS.

3

GA: 4390813_1