SiEBE12-625
Service
Manual
D-Series / E-Series
[Applied Models]
zInverter Multi : Cooling Only
zInverter Multi : Heat Pump
SiEBE12-625
SUPER MULTI NX
D-Series / E-Series
zCooling Only
Indoor Unit
FTKS20D3VMW
FTKS20D3VML
FTKS25D3VMW
FTKS25D3VML
FTKS35D3VMW
FTKS35D3VML
FTKS50D2V1W
FTKS50D2V1L
FTKS20CAVMB
FTKS25CAVMB
FTKS35CAVMB
FTKS50EV1B
FTKS60EV1B
FTKS71EV1B
FTKS71BAVMB
FDKS25CAVMB
FDKS35CAVMB
FDKS50CVMB
FDKS60CVMB
FDKS25EAVMB
FDKS35EAVMB
FLKS25BAVMB
FLKS35BAVMB
FLKS50BAVMB
FLKS60BAVMB
FVKS25BAVMB
FVKS35BAVMB
FVKS50BAVMB
FTXS35D3VMW
FTXS35D3VML
FTXS50D2V1W
FTXS50D2V1L
FTXS20CAVMB
FTXS25CAVMB
FTXS35CAVMB
FTXS50EV1B
FTXS60EV1B
FTXS71EV1B
FTXS71BAVMB
FDXS25CAVMB
FDXS35CAVMB
FDXS50CVMB
FDXS60CVMB
FDXS25EAVMB
FDXS35EAVMB
FLXS25BAVMB
FLXS35BAVMB
FLXS50BAVMB
FLXS60BAVMB
FVXS25BAVMB
FVXS35BAVMB
FVXS50BAVMB
Outdoor Unit
4MKS75E2V1B
4MKS75E3V1B
4MKS90DAVMB
zHeat Pump
Indoor Unit
FTXG25EV1BW
FTXG25EV1BS
FTXG35EV1BW
FTXG35EV1BS
CTXG50EV1BW
CTXG50EV1BS
FTXS20D3VMW
FTXS20D3VML
FTXS25D3VMW
FTXS25D3VML
Outdoor Unit
4MXS68E2V1B
4MXS68E3V1B
4MXS80DAVMB
Table of Contents
i
SiEBE12-625
1. Introduction ............................................................................................ vi
1.1 Safety Cautions ....................................................................................... vi
Part 1 List of Functions ................................................................ 1
1. List of Functions ......................................................................................2
1.1 Cooling Only Models ................................................................................2
1.2 Heat Pump Models...................................................................................7
Part 2 Specifications .................................................................. 13
1. Specifications ........................................................................................14
1.1
1.2
1.3
1.4
Indoor Units - Cooling Only ....................................................................14
Outdoor Units - Cooling Only .................................................................22
Indoor Units - Heat Pump.......................................................................23
Outdoor Units - Heat Pump ....................................................................33
Part 3 Printed Circuit Board Connector Wiring Diagram ........... 35
1. Printed Circuit Board Connector Wiring Diagram..................................36
1.1
1.2
1.3
1.4
1.5
Wall Mounted Type ................................................................................36
Duct Connected Type.............................................................................45
Floor / Ceiling Suspended Dual Type.....................................................47
Floor Standing Type ...............................................................................49
Outdoor Units .........................................................................................52
Part 4 Function and Control........................................................ 55
1. Main Functions......................................................................................56
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
Frequency Principle................................................................................56
Power-Airflow Dual Flaps, Wide Angle Louvers and Auto-Swing ..........58
Operation Starting Control......................................................................60
Fan Speed Control for Indoor Units........................................................61
Programme Dry Function .......................................................................62
Automatic Operation...............................................................................63
Thermostat Control.................................................................................64
Night Set Mode.......................................................................................65
ECONO Mode ........................................................................................66
INTELLIGENT EYE (Wall Mounted Type only) ......................................67
HOME LEAVE Operation .......................................................................69
Inverter POWERFUL Operation .............................................................70
Other Functions......................................................................................71
2. Function of Main Structural Parts..........................................................73
2.1 Main Structural Parts..............................................................................73
2.2 Function of Thermistor ...........................................................................74
3. Control Specification .............................................................................78
3.1
3.2
3.3
3.4
3.5
3.6
3.7
ii
Mode Hierarchy ......................................................................................78
Frequency Control..................................................................................79
Controls at Mode Changing / Start-up....................................................81
Discharge Pipe Control ..........................................................................82
Input Current Control..............................................................................82
Freeze-up Protection Control .................................................................83
Heating Peak-cut Control .......................................................................83
Table of Contents
SiEBE12-625
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
Fan Control.............................................................................................84
Liquid Compression Protection Function 2.............................................84
Defrost Control .......................................................................................85
Low Hz High Pressure Limit ...................................................................86
Electronic Expansion Valve Control .......................................................86
Malfunctions ...........................................................................................90
Forced Operation Mode .........................................................................91
Wiring-Error Check.................................................................................92
Additional Function.................................................................................94
Part 5 System Configuration....................................................... 97
1. System Configuration............................................................................98
1.1 Operation Instructions ............................................................................98
2. Instruction..............................................................................................99
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
Manual Contents and Reference Page ..................................................99
Safety Precautions ...............................................................................100
Names of Parts.....................................................................................102
Preparation Before Operation ..............................................................126
AUTO • DRY • COOL • HEAT • FAN Operation ...................................129
Adjusting the Air Flow Direction ...........................................................131
POWERFUL Operation ........................................................................143
OUTDOOR UNIT SILENT Operation ...................................................144
ECONO Operation ...............................................................................145
HOME LEAVE Operation .....................................................................146
INTELLIGENT EYE Operation .............................................................148
TIMER Operation .................................................................................156
Note for Multi System ...........................................................................158
Care and Cleaning ...............................................................................160
Troubleshooting ...................................................................................185
Part 6 Service Diagnosis........................................................... 191
1. Caution for Diagnosis..........................................................................192
1.1 Troubleshooting with Operation Lamp .................................................192
2. Problem Symptoms and Measures .....................................................194
3. Service Check Function ......................................................................195
4. Code Indication on the Remote Controller ..........................................198
4.1 Error Codes and Description of Fault ...................................................198
5. Troubleshooting ..................................................................................199
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
Table of Contents
Indoor Units ..........................................................................................199
Outdoor Units .......................................................................................200
Indoor Unit PCB Abnormality ...............................................................201
Freeze-up Protection Control or High Pressure Control.......................202
Fan Motor or Related Abnormality .......................................................204
Thermistor or Related Abnormality (Indoor Unit)..................................207
Shutter Drive Motor / Shutter Limit Switch Abnormality .......................208
Front Panel Open / Close Fault............................................................209
Signal Transmission Error (between Indoor and Outdoor Units)..........210
Unspecified Voltage (between Indoor and Outdoor Units) ...................211
Freeze-up Protection Control ...............................................................212
OL Activation (Compressor Overload) .................................................214
iii
SiEBE12-625
5.13
5.14
5.15
5.16
5.17
5.18
5.19
5.20
5.21
5.22
5.23
5.24
5.25
5.26
5.27
Compressor Lock .................................................................................215
DC Fan Lock ........................................................................................216
Input Over Current Detection ...............................................................217
Four Way Valve Abnormality................................................................219
Discharge Pipe Temperature Control...................................................221
High Pressure Control in Cooling .........................................................222
Position Sensor Abnormality ................................................................224
CT or Related Abnormality ...................................................................225
Thermistor or Related Abnormality (Outdoor Unit)...............................227
Electrical Box Temperature Rise..........................................................229
Radiation Fin Temperature Rise ..........................................................231
Output Over Current Detection.............................................................233
Insufficient Gas.....................................................................................235
Low-voltage Detection..........................................................................237
Anti-icing Function in Other Rooms / Unspecified Voltage
(between Indoor and Outdoor Units) ....................................................238
6. Check ..................................................................................................239
6.1 How to Check .......................................................................................239
Part 7 Removal Procedure ........................................................ 249
1. Outdoor Unit (80 / 90 Class) ...............................................................250
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
Removal of Outer Panels .....................................................................250
Removal of Propeller Fans...................................................................253
Removal of Electrical Box ....................................................................254
Removal of PCB...................................................................................261
Removal of Fan Motor..........................................................................264
Removal of Electronic Expansion Valve and Thermistor .....................266
Removal of Sound Blanket and Reactor ..............................................267
Removal of Shunt.................................................................................269
Removal of Solenoid Valve and Four Way Valve.................................270
Removal of Compressor.......................................................................272
2. Outdoor Unit (68 / 75 Class) ...............................................................274
2.1
2.2
2.3
2.4
2.5
2.6
Removal of Outer Panels .....................................................................274
Removal of Electrical BOX ...................................................................275
Removal of PCB...................................................................................279
Removal of Fan Motor..........................................................................282
Removal of Sound Blanket...................................................................283
Removal of Four Way Valve Coil, Solenoid Valve Coil,
Electronic Expansion Valve Coil and Thermistor .................................284
2.7 Removal of Four Way Valve, Solenoid Valve and Shunt .....................286
2.8 Removal of Solenoid Valve and Shunt.................................................287
2.9 Removal of Compressor.......................................................................288
Part 8 Others ............................................................................. 289
1. Others .................................................................................................290
1.1 Test Run from the Remote Controller ..................................................290
1.2 Jumper Settings ...................................................................................291
iv
Table of Contents
SiEBE12-625
Part 9 Appendix......................................................................... 293
1. Piping Diagrams..................................................................................294
1.1 Indoor Units ..........................................................................................294
1.2 Outdoor Units .......................................................................................300
2. Wiring Diagrams..................................................................................302
2.1 Indoor Units ..........................................................................................302
2.2 Outdoor Units .......................................................................................306
Index
............................................................................................. i
Drawings & Flow Charts ................................................................ v
Table of Contents
v
SiEBE12-625
Introduction
1. Introduction
1.1
Safety Cautions
Cautions and
Warnings
„ Be sure to read the following safety cautions before conducting repair work.
„ The caution items are classified into “
Warning” and “
Caution”. The “
Warning”
items are especially important since they can lead to death or serious injury if they are not
followed closely. The “
Caution” items can also lead to serious accidents under some
conditions if they are not followed. Therefore, be sure to observe all the safety caution items
described below.
„ About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
„ After the repair work is complete, be sure to conduct a test operation to ensure that the
equipment operates normally, and explain the cautions for operating the product to the
customer.
1.1.1 Caution in Repair
Warning
Be sure to disconnect the power cable plug from the plug socket before
disassembling the equipment for a repair.
Working on the equipment that is connected to a power supply can cause an
electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or
inspecting the circuits, do not touch any electrically charged sections of the
equipment.
If the refrigerant gas discharges during the repair work, do not touch the
discharging refrigerant gas.
The refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the
welded section, release the refrigerant gas completely at a well-ventilated
place first.
If there is a gas remaining inside the compressor, the refrigerant gas or
refrigerating machine oil discharges when the pipe is disconnected, and it can
cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The
refrigerant gas can generate toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical
components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.
A charged capacitor can cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the
power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can
cause an electrical shock or fire.
vi
Introduction
SiEBE12-625
Caution
Do not repair the electrical components with wet hands.
Working on the equipment with wet hands can cause an electrical shock.
Do not clean the air conditioner by splashing water.
Washing the unit with water can cause an electrical shock.
Be sure to provide the grounding when repairing the equipment in a humid or
wet place, to avoid electrical shocks.
Be sure to turn off the power switch and unplug the power cable when cleaning
the equipment.
The internal fan rotates at a high speed, and cause injury.
Do not tilt the unit when removing it.
The water inside the unit can spill and wet the furniture and floor.
Be sure to check that the refrigerating cycle section has cooled down
sufficiently before conducting repair work.
Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place.
Using the welder in an enclosed room can cause oxygen deficiency.
1.1.2 Cautions Regarding Products after Repair
Warning
Be sure to use parts listed in the service parts list of the applicable model and
appropriate tools to conduct repair work. Never attempt to modify the
equipment.
The use of inappropriate parts or tools can cause an electrical shock,
excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has
sufficient strength to withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation
work is not conducted securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard
installation frame.
Incorrect use of the installation frame and improper installation can cause the
equipment to fall, resulting in injury.
Be sure to install the product securely in the installation frame mounted on a
window frame.
If the unit is not securely mounted, it can fall and cause injury.
vii
For integral units
only
For integral units
only
SiEBE12-625
Introduction
Warning
Be sure to use an exclusive power circuit for the equipment, and follow the
technical standards related to the electrical equipment, the internal wiring
regulations and the instruction manual for installation when conducting
electrical work.
Insufficient power circuit capacity and improper electrical work can cause an
electrical shock or fire.
Be sure to use the specified cable to connect between the indoor and outdoor
units. Make the connections securely and route the cable properly so that there
is no force pulling the cable at the connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure
that the terminal cover does not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause
an electrical shock, excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire.
Placing heavy items on the power cable, and heating or pulling the power cable
can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A ) in the
refrigerant system.
If air enters the refrigerating system, an excessively high pressure results,
causing equipment damage and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before
charging the refrigerant. After charging refrigerant, make sure that there is no
refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to
perform pump-down and close the service valve, to prevent the refrigerant gas
from leaking into the room. The refrigerant gas itself is harmless, but it can
generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed
of the old battery to prevent children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.
Caution
Installation of a leakage breaker is necessary in some cases depending on the
conditions of the installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of
combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly.
For integral units
If the packing and seal are not installed properly, water can enter the room and only
wet the furniture and floor.
1.1.3 Inspection after Repair
Warning
Check to make sure that the power cable plug is not dirty or loose, then insert
the plug into a power outlet all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to
replace them.
Damaged cable and wires can cause an electrical shock, excessive heat
generation or fire.
viii
Introduction
SiEBE12-625
Warning
Do not use a joined power cable or extension cable, or share the same power
outlet with other electrical appliances, since it can cause an electrical shock,
excessive heat generation or fire.
Caution
Check to see if the parts and wires are mounted and connected properly, and
if the connections at the soldered or crimped terminals are secure.
Improper installation and connections can cause excessive heat generation,
fire or an electrical shock.
If the installation platform or frame has corroded, replace it.
Corroded installation platform or frame can cause the unit to fall, resulting in
injury.
Check the grounding, and repair it if the equipment is not properly grounded.
Improper grounding can cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure
that the resistance is 1 MΩ or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture
and floor.
1.1.4 Using Icons
Icons are used to attract the attention of the reader to specific information. The meaning of each
icon is described in the table below:
1.1.5 Using Icons List
Icon
Type of
Information
Note
Description
A “note” provides information that is not indispensable, but may
nevertheless be valuable to the reader, such as tips and tricks.
Note:
Caution
A “caution” is used when there is danger that the reader, through
incorrect manipulation, may damage equipment, loose data, get
an unexpected result or has to restart (part of) a procedure.
Warning
A “warning” is used when there is danger of personal injury.
Reference
A “reference” guides the reader to other places in this binder or
in this manual, where he/she will find additional information on a
specific topic.
Caution
Warning
ix
SiBE12-625
Part 1
List of Functions
1. List of Functions ......................................................................................2
1.1 Cooling Only Models ................................................................................2
1.2 Heat Pump Models...................................................................................7
List of Functions
1
List of Functions
SiEBE12-625
1. List of Functions
FTKS50D2V1W(L)
FTKS20-35CAVMB
{
{
{
—
—
—
Air Purifying Filter with Bacteriostatic,
Virustatic Functions
—
—
—
Basic
Function
Operation Limit for Heating (°CWB)
—
—
—
Photocatalytic Deodorizing Filter
—
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
{
Titanium Apatite Photocatalytic
Air-Purifying Filter
Compressor
{
{
—
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Functions
FTKS20-35CAVMB
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°CDB)
Category
FTKS50D2V1W(L)
FTKS20-35D3VMW(L)
Cooling Only Models
FTKS20-35D3VMW(L)
1.1
Category
Functions
PAM Control
—
—
—
Oval Scroll Compressor
—
—
—
Swing Compressor
—
—
Rotary Compressor
—
—
— Health &
Clean
—
Mold Proof Air Filter
{
{
{
Reluctance DC Motor
—
—
—
Wipe-clean Flat Panel
{
{
{
Power-Airflow Flap
—
—
—
Washable Grille
—
—
—
Power-Airflow Dual Flaps
{
{
{
Mold Proof Operation
—
—
—
Power-Airflow Diffuser
—
—
—
Heating Dry Operation
—
—
—
Wide-Angle Louvers
{
{
{
Good-Sleep Cooling Operation
—
—
—
Vertical Auto-Swing (Up and Down)
{
{
{
24-Hour On/Off Timer
{
{
{
Horizontal Auto-Swing (Right and Left) —
—
—
Night Set Mode
{
{
{
3-D Airflow
—
—
Auto-Restart (after Power Failure)
{
{
{
Self-Diagnosis (Digital, LED) Display
{
{
{
Wiring Error Check
—
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
—
Multi-Split / Split Type Compatible
Indoor Unit
{
{
{
—
Comfort Airflow Mode
{
{
3-Step Airflow (H/P Only)
—
—
Timer
Auto Fan Speed
{
{
—
Worry Free
— “Reliability &
Durability”
{
Indoor Unit Quiet Operation
{
{
{
Night Quiet Mode (Automatic)
—
—
—
Outdoor Unit Quiet Operation (Manual) —
—
—
Intelligent Eye
{
{
{
Flexible Voltage Correspondence
{
—
{
Quick Warming Function
—
—
— Flexibility
High Ceiling Application
—
—
—
Hot-Start Function
—
—
—
Chargeless
—
—
—
Automatic Defrosting
—
—
—
Either Side Drain (Right or Left)
{
{
{
Automatic Operation
—
—
—
Power Selection
—
—
—
Programme Dry Function
{
{
{
5-Rooms Centralized Controller
(Option)
{
{
{
Fan Only
{
{
{
New Powerful Operation (NonInverter)
—
—
Remote Control Adaptor
{
(Normal Open-Pulse Contact) (Option)
{
{
Inverter Powerful Operation
{
{
— Remote
Control
{
Priority-Room Setting
—
—
—
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
{
Cooling / Heating Mode Lock
—
—
—
DIII-NET Compatible (Adaptor)
(Option)
{
{
{
Wireless
{
{
{
Wired
—
—
—
Home Leave Operation
—
—
ECONO Mode
{
{
{ Remote
— Controller
Indoor Unit On/Off Switch
{
{
{
Signal Reception Indicator
{
{
{
Temperature Display
—
—
—
Another Room Operation
—
—
—
Note: { : Holding Functions
— : No Functions
2
List of Functions
FTKS71BAVMB
Inverter (with Inverter Power Control)
{
{
Operation Limit for Cooling (°CDB)
—
—
Air Purifying Filter with Bacteriostatic,
Virustatic Functions
—
—
Operation Limit for Heating (°CWB)
—
—
Photocatalytic Deodorizing Filter
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
{
Titanium Apatite Photocatalytic
Air-Purifying Filter
{
—
Mold Proof Air Filter
{
{
Category
Basic
Function
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Functions
FTKS71BAVMB
FTKS50-71EV1B
List of Functions
FTKS50-71EV1B
SiEBE12-625
PAM Control
—
—
Oval Scroll Compressor
—
—
Swing Compressor
—
—
Category
Health &
Clean
Functions
Rotary Compressor
—
—
Wipe-clean Flat Panel
{
{
Reluctance DC Motor
—
—
Washable Grille
—
—
—
Power-Airflow Flap
—
—
Mold Proof Operation
—
Power-Airflow Dual Flaps
{
{
Heating Dry Operation
—
—
Power-Airflow Diffuser
—
—
Good-Sleep Cooling Operation
—
—
{
Wide-Angle Louvers
{
{
Vertical Auto-Swing (Up and Down)
{
{
Horizontal Auto-Swing (Right and Left)
{
{
3-D Airflow
{
{
Comfort Airflow Mode
—
—
3-Step Airflow (H/P Only)
—
—
Auto Fan Speed
{
{
Indoor Unit Quiet Operation
{
{
Night Quiet Mode (Automatic)
—
—
Outdoor Unit Quiet Operation (Manual)
—
—
Intelligent Eye
{
{
Timer
Worry Free
“Reliability &
Durability”
Flexibility
24-Hour On/Off Timer
{
Night Set Mode
{
{
Auto-Restart (after Power Failure)
{
{
Self-Diagnosis (Digital, LED) Display
{
{
Wiring Error Check
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
Multi-Split / Split Type Compatible
Indoor Unit
{
{
Flexible Voltage Correspondence
—
{
High Ceiling Application
—
—
—
Quick Warming Function
—
—
Chargeless
—
Hot-Start Function
—
—
Either side Drain (Right or Left)
{
{
Automatic Defrosting
—
—
Power Selection
—
—
Automatic Operation
—
—
5-Rooms Centralized Controller
(Option)
{
{
Programme Dry Function
{
{
Fan Only
{
{
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
New Powerful Operation (NonInverter)
—
—
{
{
{
Remote Control Adaptor
(Normal Open Contact) (Option)
{
Inverter Powerful Operation
Priority-Room Setting
—
—
DIII-NET Compatible (Adaptor)
(Option)
{
{
Cooling / Heating Mode Lock
—
—
Home Leave Operation
{
{
ECONO Mode
—
—
Indoor Unit On/Off Switch
{
{
Signal Reception Indicator
{
{
Temperature Display
—
—
Another Room Operation
—
—
Remote
Control
Remote
Controller
Wireless
{
{
Wired
—
—
Note: { : Holding Functions
— : No Functions
List of Functions
3
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
FDKS25/35EAVMB
FDKS25/35CAVMB
FDKS50/60CVMB
FDKS25/35EAVMB
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
—
—
—
—
Photocatalytic Deodorizing Filter
—
—
—
—
—
—
—
—
—
FDKS25/35CAVMB
Functions
Functions
Inverter (with Inverter Power Control)
{
Operation Limit for Cooling (°CDB)
—
—
Category
Basic
Function
SiEBE12-625
FDKS50/60CVMB
List of Functions
Category
Operation Limit for Heating (°CWB)
—
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
PAM Control
—
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
Mold Proof Air Filter
{
{
{
Wipe-clean Flat Panel
—
—
—
Oval Scroll Compressor
—
—
Health &
— Clean
Swing Compressor
—
—
—
Rotary Compressor
—
—
—
Washable Grille
—
—
—
Reluctance DC Motor
—
—
—
Mold Proof Operation
—
—
—
Power-Airflow Flap
—
—
—
Heating Dry Operation
—
—
—
Power-Airflow Dual Flaps
—
—
—
Good-Sleep Cooling Operation
—
—
—
{
24-Hour On/Off Timer
{
{
Night Set Mode
{
{
{
—
Auto-Restart (after Power Failure)
{
{
{
Self-Diagnosis (Digital, LED) Display
{
{
{
Power-Airflow Diffuser
—
—
—
Wide-Angle Louvers
—
—
—
Vertical Auto-Swing (Up and Down)
—
—
Horizontal Auto-Swing (Right and Left) —
—
3-D Airflow
—
Timer
Comfort Airflow Mode
—
—
— Worry Free
— “Reliability &
Durability”
—
3-Step Airflow (H/P Only)
—
—
—
—
Wiring-Error Check
—
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
—
Multi-Split / Split Type Compatible
Indoor Unit
{
{
{
Auto Fan Speed
{
{
{
Flexible Voltage Correspondence
{
{
{
Indoor Unit Quiet Operation
{
{
High Ceiling Application
—
—
—
Night Quiet Mode (Automatic)
—
—
{ Flexibility
—
Chargeless
—
—
—
Outdoor Unit Quiet Operation (Manual) —
—
—
Either Side Drain (Right or Left)
—
—
—
Intelligent Eye
—
—
Power-Selection
—
—
—
5-Rooms Centralized Controller
(Option)
{
{
{
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
{
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
{
DIII-NET Compatible (Adaptor)
(Option)
{
{
{
—
Quick Warming Function
—
—
—
Hot-Start Function
—
—
—
Automatic Defrosting
—
—
—
Automatic Operation
—
—
—
Remote
Control
Programme Dry Function
{
{
Fan Only
{
{
{ Remote
{ Controller
New Powerful Operation
(Non-Inverter)
—
—
—
Inverter Powerful Operation
{
{
{
Priority-Room Setting
—
—
—
Cooling / Heating Mode Lock
—
—
—
Home Leave Operation
{
{
{
ECONO Mode
—
—
—
Indoor Unit On/Off Switch
{
{
{
Signal Reception Indicator
{
{
{
Temperature Display
—
—
—
Another Room Operation
—
—
—
Wireless
{
{
{
Wired
—
—
—
Note: { : Holding Functions
— : No Functions
4
List of Functions
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
FVKS25-50BAVMB
Basic
Function
Functions
FLKS25-60BAVMB
Category
FVKS25-50BAVMB
List of Functions
FLKS25-60BAVMB
SiEBE12-625
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
{
{
—
Photocatalytic Deodorizing Filter
{
{
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
—
—
Functions
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°CDB)
—
Operation Limit for Heating (°CWB)
—
—
PAM Control
—
—
Category
Health &
Clean
Oval Scroll Compressor
—
—
Mold Proof Air Filter
{
{
Swing Compressor
—
—
Wipe-clean Flat Panel
—
—
Rotary Compressor
—
—
Washable Grille
—
{
Reluctance DC Motor
—
—
Mold Proof Operation
—
—
Power-Airflow Flap
—
—
Heating Dry Operation
—
—
Power-Airflow Dual Flaps
—
—
Good-Sleep Cooling Operation
—
—
24-Hour On/Off Timer
{
{
Night Set Mode
{
{
Auto-Restart (after Power Failure)
{
{
Self-Diagnosis (Digital, LED) Display
{
{
Power-Airflow Diffuser
—
—
Wide-Angle Louvers
—
{
Vertical Auto-Swing (Up and Down)
{
{
Horizontal Auto-Swing (Right and Left)
—
—
3-D Airflow
—
—
Timer
Worry Free
“Reliability &
Durability”
Wiring-Error Check
—
—
—
—
{
{
Comfort Airflow Mode
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
3-Step Airflow (H/P Only)
—
—
Multi-Split / Split Type Compatible
Indoor Unit
Auto Fan Speed
{
{
Flexible Voltage Correspondence
{
{
Indoor Unit Quiet Operation
{
{
High Ceiling Application
—
—
Night Quiet Mode (Automatic)
—
—
Chargeless
—
—
Outdoor Unit Quiet Operation (Manual)
—
—
Either Side Drain (Right or Left)
—
—
Intelligent Eye
—
—
Power-Selection
—
—
Quick Warming Function
—
—
5-Rooms Centralized Controller
(Option)
{
{
Hot-Start Function
—
—
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
Automatic Defrosting
—
—
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
Flexibility
Remote
Control
Automatic Operation
—
—
DIII-NET Compatible (Adaptor) (Option)
{
{
Programme Dry Function
{
{
Wireless
{
{
Fan Only
{
{
Wired
—
—
New Powerful Operation
(Non-Inverter)
—
—
Inverter Powerful Operation
{
{
Priority-Room Setting
—
—
Cooling / Heating Mode Lock
—
—
Home Leave Operation
{
{
ECONO Mode
—
—
Indoor Unit On/Off Switch
{
{
Signal Reception Indicator
{
{
Temperature Display
—
—
Another Room Operation
—
—
Remote
Controller
Note: { : Holding Functions
— : No Functions
List of Functions
5
{
{
Operation Limit for Cooling (°CDB)
–10
~
46
–10
~
46
Operation Limit for Heating (°CWB)
—
—
PAM Control
{
{
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
4MKS90DAVMB
4MKS90DAVMB
Inverter (with Inverter Power Control)
Functions
4MKS75E2(3)V1B
Functions
Category
Basic
Function
SiEBE12-625
4MKS75E2(3)V1B
List of Functions
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
—
—
Photocatalytic Deodorizing Filter
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
—
—
Category
Health &
Clean
Oval Scroll Compressor
—
—
Mold Proof Air Filter
—
—
Swing Compressor
{
{
Wipe-clean Flat Panel
—
—
Rotary Compressor
—
—
Washable Grille
—
—
Reluctance DC Motor
{
{
Mold Proof Operation
—
—
Power-Airflow Flap
—
—
Heating Dry Operation
—
—
Power-Airflow Dual Flaps
—
—
Good-Sleep Cooling Operation
—
—
—
Power-Airflow Diffuser
—
—
Wide-Angle Louvers
—
—
Vertical Auto-Swing (Up and Down)
—
—
Horizontal Auto-Swing (Right and Left)
—
—
3-D Airflow
—
—
Timer
Worry Free
“Reliability &
Durability”
24-Hour On/Off Timer
—
Night Set Mode
—
—
Auto-Restart (after Power Failure)
—
—
Self-Diagnosis (Digital, LED) Display
{
{
Wiring-Error Check
{
{
{
{
—
—
Comfort Airflow Mode
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
3-Step Airflow (H/P Only)
—
—
Multi-Split / Split Type Compatible
Indoor Unit
Auto Fan Speed
—
—
Flexible Voltage Correspondence
—
{
Indoor Unit Quiet Operation
—
—
High Ceiling Application
—
—
Night Quiet Mode (Automatic)
{
{
Chargeless
{
{
Outdoor Unit Quiet Operation (Manual)
{
{
Either Side Drain (Right or Left)
—
—
Intelligent Eye
—
—
Power-Selection
—
—
Quick Warming Function
—
—
5-Rooms Centralized Controller
(Option)
—
—
Hot-Start Function
—
—
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
—
—
Automatic Defrosting
—
—
Remote Control Adaptor
(Normal Open Contact) (Option)
—
—
Flexibility
Remote
Control
Automatic Operation
—
—
DIII-NET Compatible (Adaptor) (Option)
—
—
Programme Dry Function
—
—
Wireless
—
—
Fan Only
—
—
Wired
—
—
New Powerful Operation
(Non-Inverter)
—
—
Inverter Powerful Operation
—
—
Priority-Room Setting
{
{
Cooling / Heating Mode Lock
—
—
Home Leave Operation
—
—
ECONO Mode
—
—
Indoor Unit On/Off Switch
—
—
Signal Reception Indicator
—
—
Temperature Display
—
—
Another Room Operation
—
—
Remote
Controller
Note: { : Holding Functions
— : No Functions
6
List of Functions
SiEBE12-625
CTXG50EV1BW(S)
Inverter (with Inverter Power Control)
{
{
Operation Limit for Cooling (°CDB)
—
—
Air Purifying Filter with Bacteriostatic,
Virustatic Functions
—
—
Operation Limit for Heating (°CWB)
—
—
Photocatalytic Deodorizing Filter
—
—
PAM Control
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
{
{
Category
Basic
Function
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Functions
CTXG50EV1BW(S)
FTXG25/35EV1BW(S)
Heat Pump Models
FTXG25/35EV1BW(S)
1.2
List of Functions
Category
Functions
Oval Scroll Compressor
—
—
Swing Compressor
—
—
Rotary Compressor
—
—
Mold Proof Air Filter
{
{
Reluctance DC Motor
—
—
Wipe-clean Flat Panel
{
{
Health &
Clean
Power-Airflow Flap
{
{
Washable Grille
—
—
Power-Airflow Dual Flaps
—
—
Mold Proof Operation
—
—
Power-Airflow Diffuser
—
—
Heating Dry Operation
—
—
Wide-Angle Louvers
{
{
Good-Sleep Cooling Operation
—
—
Vertical Auto-Swing (Up and Down)
{
{
24-Hour On/Off Timer
{
{
Horizontal Auto-Swing (Right and Left)
{
{
Night Set Mode
{
{
3-D Airflow
{
{
Auto-Restart (after Power Failure)
{
{
Comfort Airflow Mode
{
{
3-Step Airflow (H/P Only)
—
—
Auto Fan Speed
{
{
Indoor Unit Quiet Operation
{
{
Night Quiet Mode (Automatic)
—
—
Outdoor Unit Quiet Operation (Manual)
—
—
Intelligent Eye
{
{
Quick Warming Function
—
—
Timer
Worry Free
“Reliability &
Durability”
Flexibility
Self-Diagnosis (Digital, LED) Display
{
{
Wiring Error Check
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
Multi-Split / Split Type Compatible
Indoor Unit
{
—
Flexible Voltage Correspondence
—
—
High Ceiling Application
—
—
—
Hot-Start Function
{
{
Chargeless
—
Automatic Defrosting
—
—
Either Side Drain (Right or Left)
{
{
Automatic Operation
{
{
Power Selection
—
—
Programme Dry Function
{
{
5-Rooms Centralized Controller
(Option)
{
{
Fan Only
{
{
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
New Powerful Operation (NonInverter)
—
—
Inverter Powerful Operation
{
{
Remote
Control
Priority-Room Setting
—
—
DIII-NET Compatible (Adaptor) (Option)
{
{
Cooling / Heating Mode Lock
—
—
Wireless
{
{
Home Leave Operation
—
—
Wired
—
—
ECONO Mode
—
—
Indoor Unit On/Off Switch
{
{
Signal Reception Indicator
{
{
Temperature Display
—
—
Another Room Operation
—
—
Remote
Controller
Note: { : Holding Functions
— : No Functions
List of Functions
7
FTXS20-35D3VMW(L)
FTXS50D2V1W(L)
FTXS20-35CAVMB
{
{
—
—
Air Purifying Filter with Bacteriostatic,
Virustatic Functions
—
—
—
Operation Limit for Heating (°CWB)
—
—
—
Photocatalytic Deodorizing Filter
—
—
—
—
—
{
{
{
—
Compressor
Comfortable
Airflow
Comfort
Control
Lifestyle
Convenience
Category
Functions
PAM Control
—
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
Oval Scroll Compressor
—
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
Swing Compressor
—
—
Health &
— Clean
Mold Proof Air Filter
{
{
{
Rotary Compressor
—
—
—
Wipe-clean Flat Panel
{
{
{
Reluctance DC Motor
—
—
—
Washable Grille
—
—
—
—
Power-Airflow Flap
—
—
—
Mold Proof Operation
—
—
Power-Airflow Dual Flaps
{
{
{
Heating Dry Operation
—
—
—
Power-Airflow Diffuser
—
—
—
Good-Sleep Cooling Operation
—
—
—
Wide-Angle Louvers
{
{
{
Vertical Auto-Swing (Up and Down)
{
{
{
Timer
24-Hour On/Off Timer
{
{
{
Night Set Mode
{
{
{
Horizontal Auto-Swing (Right and Left) —
—
—
Auto-Restart (after Power Failure)
{
{
{
3-D Airflow
—
—
—
{
{
{
Comfort Airflow Mode
{
{
Wiring Error Check
—
—
—
3-Step Airflow (H/P Only)
—
—
Worry Free
— “Reliability &
Durability”
—
Self-Diagnosis (Digital, LED) Display
Auto Fan Speed
{
{
{
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
—
{
{
{
Indoor Unit Quiet Operation
{
{
{
Night Quiet Mode (Automatic)
—
—
—
Multi-Split / Split Type Compatible
Indoor Unit
Outdoor Unit Quiet Operation (Manual) —
—
—
Flexible Voltage Correspondence
{
—
{
Intelligent Eye
{
{
{ Flexibility
High Ceiling Application
—
—
—
Quick Warming Function
—
—
—
Chargeless
—
—
—
Hot-Start Function
{
{
{
Either side Drain (Right or Left)
{
{
{
Automatic Defrosting
—
—
—
Power Selection
—
—
—
{
5-Rooms Centralized Controller
(Option)
{
{
{
Remote Control Adaptor
{
(Normal Open-Pulse Contact) (Option)
{
{
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
{
Automatic Operation
Operation
FTXS20-35CAVMB
{
—
Functions
FTXS50D2V1W(L)
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°CDB)
Category
Basic
Function
SiEBE12-625
FTXS20-35D3VMW(L)
List of Functions
{
{
Programme Dry Function
{
{
{
Fan Only
{
{
{
New Powerful Operation (NonInverter)
—
—
Remote
— Control
Inverter Powerful Operation
{
{
{
Priority-Room Setting
—
—
—
DIII-NET Compatible (Adaptor)
(Option)
{
{
{
Cooling / Heating Mode Lock
—
—
Wireless
{
{
{
Home Leave Operation
—
—
— Remote
{ Controller
Wired
—
—
—
ECONO Mode
{
{
—
Indoor Unit On/Off Switch
{
{
{
Signal Reception Indicator
{
{
{
Temperature Display
—
—
—
Another Room Operation
—
—
—
Note: { : Holding Functions
— : No Functions
8
List of Functions
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
FTXS71BAVMB
Basic
Function
Functions
FTXS50-71EV1B
Category
FTXS71BAVMB
List of Functions
FTXS50-71EV1B
SiEBE12-625
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
—
—
—
Photocatalytic Deodorizing Filter
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
{
Titanium Apatite Photocatalytic
Air-Purifying Filter
{
—
Functions
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°CDB)
—
Operation Limit for Heating (°CWB)
—
—
PAM Control
—
—
Oval Scroll Compressor
—
—
Swing Compressor
—
—
Category
Health &
Clean
Mold Proof Air Filter
{
{
Wipe-clean Flat Panel
{
{
Rotary Compressor
—
—
Washable Grille
—
—
Reluctance DC Motor
—
—
Mold Proof Operation
—
—
Power-Airflow Flap
—
—
Heating Dry Operation
—
—
Power-Airflow Dual Flaps
{
{
Good-Sleep Cooling Operation
—
—
24-Hour On/Off Timer
{
{
Night Set Mode
{
{
Auto-Restart (after Power Failure)
{
{
Self-Diagnosis (Digital, LED) Display
{
{
Power-Airflow Diffuser
—
—
Wide-Angle Louvers
{
{
Vertical Auto-Swing (Up and Down)
{
{
Horizontal Auto-Swing (Right and Left)
{
{
3-D Airflow
{
{
Timer
Worry Free
“Reliability &
Durability”
Wiring-Error Check
—
—
—
—
{
{
Comfort Airflow Mode
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
3-Step Airflow (H/P Only)
—
—
Multi-Split / Split Type Compatible
Indoor Unit
Auto Fan Speed
{
{
Flexible Voltage Correspondence
—
{
Indoor Unit Quiet Operation
{
{
High Ceiling Application
—
—
Night Quiet Mode (Automatic)
—
—
Chargeless
—
—
Outdoor Unit Quiet Operation (Manual)
—
—
Either Side Drain (Right or Left)
{
{
Intelligent Eye
{
{
Power-Selection
—
—
Quick Warming Function
—
—
5-Rooms Centralized Controller
(Option)
{
{
Hot-Start Function
{
{
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
Automatic Defrosting
—
—
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
Automatic Operation
{
{
DIII-NET Compatible (Adaptor)
(Option)
{
{
Programme Dry Function
{
{
Fan Only
{
{
New Powerful Operation
(Non-Inverter)
—
—
Inverter Powerful Operation
{
{
Priority-Room Setting
—
—
Cooling / Heating Mode Lock
—
—
Home Leave Operation
{
{
ECONO Mode
—
—
Indoor Unit On/Off Switch
{
{
Signal Reception Indicator
{
{
Temperature Display
—
—
Another Room Operation
—
—
Flexibility
Remote
Control
Remote
Controller
Wireless
{
{
Wired
—
—
Note: { : Holding Functions
— : No Functions
List of Functions
9
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
FDXS25/35EAVMB
FDXS25/35CAVMB
FDXS50/60CVMB
FDXS25/35EAVMB
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
—
—
—
—
Photocatalytic Deodorizing Filter
—
—
—
—
—
—
—
—
—
FDXS25/35CAVMB
Functions
Functions
Inverter (with Inverter Power Control)
{
Operation Limit for Cooling (°CDB)
—
—
Category
Basic
Function
SiEBE12-625
FDXS50/60CVMB
List of Functions
Category
Operation Limit for Heating (°CWB)
—
—
—
Air Purifying Filter with Photocatalytic
Deodorizing Function
PAM Control
—
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
Mold Proof Air Filter
{
{
{
Wipe-clean Flat Panel
—
—
—
Oval Scroll Compressor
—
—
Health &
— Clean
Swing Compressor
—
—
—
Rotary Compressor
—
—
—
Washable Grille
—
—
—
Reluctance DC Motor
—
—
—
Mold Proof Operation
—
—
—
Power-Airflow Flap
—
—
—
Heating Dry Operation
—
—
—
Power-Airflow Dual Flaps
—
—
—
Good-Sleep Cooling Operation
—
—
—
{
24-Hour On/Off Timer
{
{
Night Set Mode
{
{
{
—
Auto-Restart (after Power Failure)
{
{
{
Self-Diagnosis (Digital, LED) Display
{
{
{
Wiring-Error Check
—
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
—
—
—
Multi-Split / Split Type Compatible
Indoor Unit
{
{
{
Power-Airflow Diffuser
—
—
—
Wide-Angle Louvers
—
—
—
Vertical Auto-Swing (Up and Down)
—
—
Horizontal Auto-Swing (Right and Left) —
—
3-D Airflow
—
Timer
3-Step Airflow (H/P Only)
—
—
— Worry Free
— “Reliability &
Durability”
—
Auto Fan Speed
{
{
{
—
Indoor Unit Quiet Operation
{
{
{
Flexible Voltage Correspondence
{
{
{
Night Quiet Mode (Automatic)
—
—
High Ceiling Application
—
—
—
Outdoor Unit Quiet Operation (Manual) —
—
— Flexibility
—
Chargeless
—
—
—
Intelligent Eye
—
—
—
Either Side Drain (Right or Left)
—
—
—
Quick Warming Function
—
—
—
Power-Selection
—
—
—
Hot-Start Function
{
{
{
5-Rooms Centralized Controller
(Option)
{
{
{
Automatic Defrosting
—
—
Remote Control Adaptor
{
(Normal Open-Pulse Contact) (Option)
{
{
Automatic Operation
{
{
— Remote
Control
{
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
{
Programme Dry Function
{
{
{
DIII-NET Compatible (Adaptor) (Option)
{
{
{
Fan Only
{
{
{
Wireless
{
{
{
New Powerful Operation
(Non-Inverter)
—
—
Wired
—
—
—
Remote
— Controller
Inverter Powerful Operation
{
{
{
Priority-Room Setting
—
—
—
Cooling / Heating Mode Lock
—
—
—
Home Leave Operation
{
{
{
ECONO Mode
—
—
—
Indoor Unit On/Off Switch
{
{
{
Signal Reception Indicator
{
{
{
Temperature Display
—
—
—
Another Room Operation
—
—
—
Note: { : Holding Functions
— : No Functions
10
List of Functions
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
FVXS25-50BAVMB
Basic
Function
Functions
FLXS25-60BAVMB
Category
FVXS25-50BAVMB
List of Functions
FLXS25-60BAVMB
SiEBE12-625
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
{
{
—
Photocatalytic Deodorizing Filter
{
{
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
Titanium Apatite Photocatalytic
Air-Purifying Filter
—
—
Functions
Inverter (with Inverter Power Control)
Operation Limit for Cooling (°CDB)
—
Operation Limit for Heating (°CWB)
—
—
PAM Control
—
—
Category
Health &
Clean
Oval Scroll Compressor
—
—
Mold Proof Air Filter
{
{
Swing Compressor
—
—
Wipe-clean Flat Panel
—
—
Rotary Compressor
—
—
Washable Grille
—
{
Reluctance DC Motor
—
—
Mold Proof Operation
—
—
Power-Airflow Flap
—
—
Heating Dry Operation
—
—
Power-Airflow Dual Flaps
—
—
Good-Sleep Cooling Operation
—
—
24-Hour On/Off Timer
{
{
Night Set Mode
{
{
Auto-Restart (after Power Failure)
{
{
Self-Diagnosis (Digital, LED) Display
{
{
Power-Airflow Diffuser
—
—
Wide-Angle Louvers
—
{
Vertical Auto-Swing (Up and Down)
{
{
Horizontal Auto-Swing (Right and Left)
—
—
3-D Airflow
—
—
Timer
Worry Free
“Reliability &
Durability”
Wiring-Error Check
—
—
—
—
{
{
Comfort Airflow Mode
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
3-Step Airflow (H/P Only)
—
{
Multi-Split / Split Type Compatible
Indoor Unit
Auto Fan Speed
{
{
Flexible Voltage Correspondence
{
{
Indoor Unit Quiet Operation
{
{
High Ceiling Application
—
—
Night Quiet Mode (Automatic)
—
—
Chargeless
—
—
Outdoor Unit Quiet Operation (Manual)
—
—
Either Side Drain (Right or Left)
—
—
Intelligent Eye
—
—
Power-Selection
—
—
Quick Warming Function
—
—
5-Rooms Centralized Controller
(Option)
{
{
Hot-Start Function
{
{
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
{
{
Automatic Defrosting
—
—
Remote Control Adaptor
(Normal Open Contact) (Option)
{
{
Flexibility
Remote
Control
Automatic Operation
{
{
DIII-NET Compatible (Adaptor) (Option)
{
{
Programme Dry Function
{
{
Wireless
{
{
Fan Only
{
{
Wired
—
—
New Powerful Operation
(Non-Inverter)
—
—
Inverter Powerful Operation
{
{
Priority-Room Setting
—
—
Cooling / Heating Mode Lock
—
—
Home Leave Operation
{
{
ECONO Mode
—
—
Indoor Unit On/Off Switch
{
{
Signal Reception Indicator
{
{
Temperature Display
—
—
Another Room Operation
—
—
Remote
Controller
Note: { : Holding Functions
— : No Functions
List of Functions
11
Functions
4MXS68E2(3)V1B
4MXS80DAVMB
Functions
4MXS80DAVMB
SiEBE12-625
4MXS68E2(3)V1B
List of Functions
Inverter (with Inverter Power Control)
{
{
Air Purifying Filter with Bacteriostatic &
Virustatic Functions
—
—
Operation Limit for Cooling (°CDB)
–10
~
46
–10
~
46
Photocatalytic Deodorizing Filter
—
—
Operation Limit for Heating (°CWB)
–15
~
15.5
–15
~
15.5
Air Purifying Filter with Photocatalytic
Deodorizing Function
—
—
PAM Control
{
{
Titanium Apatite Photocatalytic
Air-Purifying Filter
—
—
Category
Basic
Function
Compressor
Comfortable
Airflow
Comfort
Control
Operation
Lifestyle
Convenience
Category
Health &
Clean
Oval Scroll Compressor
—
—
Mold Proof Air Filter
—
—
Swing Compressor
{
{
Wipe-clean Flat Panel
—
—
Rotary Compressor
—
—
Washable Grille
—
—
Reluctance DC Motor
{
{
Mold Proof Operation
—
—
Power-Airflow Flap
—
—
Heating Dry Operation
—
—
Power-Airflow Dual Flaps
—
—
Good-Sleep Cooling Operation
—
—
—
Power-Airflow Diffuser
—
—
Wide-Angle Louvers
—
—
Vertical Auto-Swing (Up and Down)
—
—
Horizontal Auto-Swing (Right and Left)
—
—
3-D Airflow
—
—
Timer
Worry Free
“Reliability &
Durability”
24-Hour On/Off Timer
—
Night Set Mode
—
—
Auto-Restart (after Power Failure)
—
—
Self-Diagnosis (Digital, LED) Display
{
{
Wiring-Error Check
{
{
{
{
—
—
Comfort Airflow Mode
—
—
Anticorrosion Treatment of Outdoor
Heat Exchanger
3-Step Airflow (H/P Only)
—
—
Multi-Split / Split Type Compatible
Indoor Unit
Auto Fan Speed
—
—
Flexible Voltage Correspondence
—
{
Indoor Unit Quiet Operation
—
—
High Ceiling Application
—
—
Night Quiet Mode (Automatic)
{
{
Chargeless
30m
40m
Outdoor Unit Quiet Operation (Manual)
{
{
Either Side Drain (Right or Left)
—
—
Intelligent Eye
—
—
Power-Selection
—
—
Quick Warming Function
{
{
5-Rooms Centralized Controller
(Option)
—
—
Hot-Start Function
—
—
Remote Control Adaptor
(Normal Open-Pulse Contact) (Option)
—
—
Automatic Defrosting
{
{
Remote Control Adaptor
(Normal Open Contact) (Option)
—
—
Flexibility
Remote
Control
Automatic Operation
—
—
DIII-NET Compatible (Adaptor) (Option)
—
—
Programme Dry Function
—
—
Wireless
—
—
Fan Only
—
—
Wired
—
—
New Powerful Operation
(Non-Inverter)
—
—
Inverter Powerful Operation
—
—
Priority-Room Setting
{
{
Cooling / Heating Mode Lock
{
{
Home Leave Operation
—
—
ECONO Mode
—
—
Indoor Unit On/Off Switch
—
—
Signal Reception Indicator
—
—
Temperature Display
—
—
Another Room Operation
—
—
Remote
Controller
Note: { : Holding Functions
— : No Functions
12
List of Functions
SiEBE12-625
Part 2
Specifications
1. Specifications ........................................................................................14
1.1
1.2
1.3
1.4
Specifications
Indoor Units - Cooling Only ....................................................................14
Outdoor Units - Cooling Only .................................................................22
Indoor Units - Heat Pump.......................................................................23
Outdoor Units - Heat Pump ....................................................................33
13
Specifications
SiEBE12-625
1. Specifications
1.1
Indoor Units - Cooling Only
Wall Mounted Type
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
mm
mm
kg
kg
FTKS20D3VMW
2.0kW Class
White
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
35
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
FTKS20D3VML
2.0kW Class
Silver Line
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
35
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
dBA
38/25/22
38/25/22
dBA
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051079
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051080
mm
mm
kg
kg
FTKS25D3VMW
2.5kW Class
White
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
35
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
FTKS25D3VML
2.5kW Class
Silver Line
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
35
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
dBA
38/25/22
38/25/22
dBA
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051081
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051082
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
14
Specifications
SiEBE12-625
Specifications
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
mm
mm
kg
kg
FTKS35D3VMW
3.5kW Class
White
8.9 (314)
6.9 (244)
4.8 (169)
4.0 (141)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
283×800×195
265×855×340
9
12
FTKS35D3VML
3.5kW Class
Silver Line
8.9 (314)
6.9 (244)
4.8 (169)
4.0 (141)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
283×800×195
265×855×340
9
12
dBA
39/26/23
39/26/23
dBA
57
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051083
57
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051084
mm
mm
kg
kg
FTKS20CAVMB
2.0kW Class
White
7.7 (272)
5.9 (208)
4.2 (148)
3.6 (127)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
FTKS25CAVMB
2.5kW Class
White
7.7 (272)
5.9 (208)
4.2 (148)
3.6 (127)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
dBA
38/32/25/22
38/32/25/22
dBA
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050947
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050949
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
15
Specifications
SiEBE12-625
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Fan
Piping Connection
Liquid
Gas
Drain
mm
mm
kg
kg
FTKS35CAVMB
3.5kW Class
White
7.7 (272)
6.0 (212)
4.4 (155)
3.8 (134)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
FTKS50D2V1W
5.0kW Class
White
11.4 (402)
9.3 (328)
7.1 (251)
6.2 (219)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.21
48
99.4
Microcomputer Control
283×800×195
265×855×340
9
12
dBA
39/33/26/23
46/41/35/32
dBA
57
Both Liquid and Gas Pipes
62
Both Liquid and Gas Pipes
mm
mm
mm
φ 6.4
φ 9.5
φ18.0
φ 6.4
φ12.7
φ18.0
3D050951
3D051812
mm
mm
kg
kg
FTKS50D2V1L
5.0kW Class
Silver Line
11.4 (402)
9.3 (328)
7.1 (251)
6.2 (219)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.21
48
99.4
Microcomputer Control
283×800×195
265×855×340
9
12
FTKS50EV1B
5.0kW Class
White
14.7 (519)
12.4 (438)
10.3 (364)
9.5 (335)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.15
34
98.6
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
dBA
46/41/35/32
43/39/34/31
dBA
62
Both Liquid and Gas Pipes
59
Both Liquid and Gas Pipes
mm
mm
mm
φ 6.4
φ12.7
φ18.0
φ 6.4
φ12.7
φ18.0
3D051813
3D051643
H
M
L
SL
W
Steps
A
W
%
Drawing No.
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Fan
Piping Connection
Drawing No.
Liquid
Gas
Drain
H
M
L
SL
W
Steps
A
W
%
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
16
Specifications
SiEBE12-625
Specifications
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
mm
mm
kg
kg
FTKS60EV1B
6.0kW Class
White
16.2 (572)
13.6 (480)
11.4 (402)
10.2 (360)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
40
96.6
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
FTKS71EV1B
7.1kW Class
White
17.4 (614)
14.6 (515)
11.6 (409)
10.6 (374)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.20
45
97.8
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
dBA
45/41/36/33
46/42/37/34
dBA
61
Both Liquid and Gas Pipes
φ 6.4
φ 12.7
φ18.0
3D051644
63
Both Liquid and Gas Pipes
φ 6.4
φ 15.9
φ18.0
3D052804
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
mm
mm
kg
kg
FTKS71BAVMB
7.1kW Class
White
16.7 (590)
14.2 (501)
11.6 (409)
10.6 (374)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.20
45
96.4
Microcomputer Control
290×1,050×238
337×1,147×336
12
17
dBA
46/42/37/34
dBA
63
Both Liquid and Gas Pipes
φ 6.4
φ15.9
φ18.0
3D050879
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
17
Specifications
SiEBE12-625
Duct Connected Type
50Hz 230V
Model
Rated Capacity
FDKS25CAVMB
2.5kW Class
—
—
mm
mm
kg
kg
9.5 (335)
8.8 (311)
8.0 (282)
6.7 (237)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.47
100
92.5
Microcomputer Control
200×900×620
266×1,106×751
25
31
10.0 (353)
9.3 (328)
8.5 (300)
7.0 (247)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.47
100
92.5
Microcomputer Control
200×900×620
266×1,106×751
25
31
dBA
35/33/31/29
35/33/31/29
Pa
L/h
40
1.2
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ26 / I.D. φ20)
3D048947C
40
1.9
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ26 / I.D. φ20)
3D048948C
FDKS50CVMB
5.0kW Class
FDKS60CVMB
6.0kW Class
Front Panel Color
m³/min
(cfm)
Air Flow Rates
Fan
Type
Motor Output
Speed
H
M
L
SL
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Moisture Removal
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
A
W
%
mm
mm
mm
Model
Rated Capacity
—
—
mm
mm
kg
kg
12.0 (424)
11.0 (388)
10.0 (353)
8.4 (297)
Sirocco Fan
130
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.64
140
95.1
Microcomputer Control
200×900×620
266×1,106×751
27
34
16.0 (565)
14.8 (523)
13.5 (477)
11.2 (395)
Sirocco Fan
130
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.74
160
94.0
Microcomputer Control
200×1,100×620
266×1,306×751
30
37
dBA
37/35/33/31
38/36/34/32
Pa
L/h
40
2.9
Both Liquid and Gas Pipes
φ 6.4
φ12.7
VP20 (O.D. φ26 / I.D. φ20)
3D052134A
40
3.9
Both Liquid and Gas Pipes
φ 6.4
φ12.7
VP20 (O.D. φ26 / I.D. φ20)
3D052135
Front Panel Color
m³/min
(cfm)
Air Flow Rates
Fan
Type
Motor Output
Speed
H
M
L
SL
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Moisture Removal
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
FDKS35CAVMB
3.5kW Class
A
W
%
mm
mm
mm
Conversion Formulae
Note:
18
1. The operating sound is based on the rear side suction inlet and the external static pressure 40 Pa.
Operating sound for under side suction inlet: [operating sound for rear side suction inlet]+5 dB.
However, when installation to which the external static pressure becomes low is carried out,
5 dB or more may go up.
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
SiEBE12-625
Specifications
50Hz 230V
Model
Rated Capacity
FDKS25EAVMB
2.5kW Class
—
—
mm
mm
kg
kg
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.48
71
64.3
Microcomputer Control
200×700×620
274×906×751
21
29
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.48
71
64.3
Microcomputer Control
200×700×620
274×906×751
21
29
dBA
35/33/31/29
35/33/31/29
Pa
L/h
30
1.2
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D.φ 26 / I.D.φ 20)
3D051882A
30
1.9
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D.φ 26 / I.D.φ 20)
3D051884A
Front Panel Color
m³/min
(cfm)
Air Flow Rates
Fan
Type
Motor Output
Speed
Note:
Specifications
H
M
L
SL
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Moisture Removal
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
FDKS35EAVMB
3.5kW Class
A
W
%
mm
mm
mm
Conversion Formulae
1. The operating sound is based on the rear side suction inlet and the external static pressure 30 Pa.
Operating sound for under side suction inlet: [operating sound for rear side suction inlet]+6 dB.
However, when installation to which the external static pressure becomes low is carried out,
6 dB or more may go up.
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
19
Specifications
SiEBE12-625
Floor / Ceiling Suspended Dual Type
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Fan
Piping Connection
Liquid
Gas
Drain
mm
mm
kg
kg
FLKS25BAVMB
2.5kW Class
Almond White
7.6 (268)
6.8 (240)
6.0 (212)
5.2 (184)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.34
74
94.6
Microcomputer Control
490×1,050×200
566×1,100×280
16
22
FLKS35BAVMB
3.5kW Class
Almond White
8.6 (304)
7.6 (268)
6.6 (233)
5.6 (198)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.36
78
94.2
Microcomputer Control
490×1,050×200
566×1,100×280
16
22
dBA
37/34/31/28
38/35/32/29
dBA
53
Both Liquid and Gas Pipes
54
Both Liquid and Gas Pipes
mm
mm
mm
φ 6.4
φ 9.5
φ18.0
φ 6.4
φ 9.5
φ18.0
3D050862
3D050864
mm
mm
kg
kg
FLKS50BAVMB
5.0W Class
Almond White
11.4 (402)
10.0 (353)
8.5 (300)
7.5 (265)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.45
96
92.8
Microcomputer Control
490×1,050×200
280×1,100×566
17
24
FLKS60BAVMB
6.0kW Class
Almond White
12.0 (424)
10.7 (378)
9.3 (328)
8.3 (293)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.45
98
94.7
Microcomputer Control
490×1,050×200
280×1,100×566
17
24
dBA
47/43/39/36
48/45/41/39
dBA
63
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D050896
64
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D050881
H
M
L
SL
W
Steps
A
W
%
Drawing No.
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
H
M
L
SL
W
Steps
A
W
%
mm
mm
mm
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
20
Specifications
SiEBE12-625
Specifications
Floor Standing Type
50Hz 230V
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Fan
Piping Connection
Liquid
Gas
Drain
mm
mm
kg
kg
FVKS25BAVMB
2.5kW Class
Almond White
8.1 (286)
6.2 (219)
4.3 (152)
3.4 (120)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
0.14
32
99.4
Microcomputer Control
600×650×195
714×770×294
13
19
FVKS35BAVMB
3.5kW Class
Almond White
8.3 (293)
6.3 (222)
4.3 (152)
3.4 (120)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
0.14
32
99.4
Microcomputer Control
600×650×195
714×770×294
13
19
dBA
38/32/26/23
39/33/27/24
dBA
54
Both Liquid and Gas Pipes
55
Both Liquid and Gas Pipes
mm
mm
mm
φ 6.4
φ 9.5
φ18.0
φ 6.4
φ 9.5
φ18.0
3D050870
3D050872
H
M
L
SL
W
Steps
A
W
%
Drawing No.
Model
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Fan
Piping Connection
Drawing No.
Liquid
Gas
Drain
mm
mm
kg
kg
FVKS50BAVMB
5.0kW Class
Almond White
10.8 (381)
9.2 (325)
7.7 (272)
6.7 (237)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
0.26
55
92.0
Microcomputer Control
600×650×195
714×770×294
13
19
dBA
44/40/36/33
dBA
56
Both Liquid and Gas Pipes
mm
mm
mm
φ 6.4
φ12.7
φ20.0
H
M
L
SL
W
Steps
A
W
%
3D050894
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
21
Specifications
1.2
SiEBE12-625
Outdoor Units - Cooling Only
50Hz 230V
Model
Cooling Capacity
kW
Power Consumption
W
Running Current
A
Casing Color
Type
Compressor
Model
Motor Output
Model
Refrigerant Oil
Charge
Type
Refrigerant
Charge
W
L
m³/min
Air Flow Rates
cfm
Fan
Type
Motor Output
Running Current
Power Consumption
Starting Current
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation Sound
Sound Power
Liquid
Gas
Piping Connection
Drain
Heat Insulation
No. of Wiring Connection
Max. Interunit Piping Length
Amount of Additional Charge
Max. Installation Height Difference
kg
H
L
H
L
W
A
W
A
mm
mm
kg
kg
dBA
dBA
mm
mm
mm
m
m
g/m
m
m
Drawing No.
Note:
22
4MKS75E2(3)V1B
4MKS90DAVMB
—
—
—
—
—
—
Ivory White
Hermetically Sealed Swing Type
2YC45BXD
1,380
FVC50K
0.75
R-410A
2.3
51
45
1,801
1,589
Propeller
53
H: 0.33 / L: 0.25
H: 68 / L: 46
8.7
735×936×300
784×992×390
58
64
48
61
φ 6.4×4
φ 9.5×2, φ12.7×1, φ15.9×1
φ18.0
Both Liquid and Gas Pipes
3 for Power Supply, 4 for Interunit Wiring
60 (for Total of Each Room)
25 (for One Room)
Chargeless
15 (between Indoor Unit and Outdoor Unit)
15 (between Indoor Units)
3D051892#1
Ivory White
Hermetically Sealed Swing Type
2YC45BXD
1,380
FVC50K
0.75
R-410A
3.1
48.5
42
1,713
1,483
Propeller
51
H: 0.44 / L: 0.34
H: 60 / L: 41
9.1
908×900×320
1,025×926×402
66
79
48
61
φ 6.4×4
φ 9.5×1, φ12.7×1, φ15.9×2
φ25.0
Both Liquid and Gas Pipes
3 for Power Supply, 4 for Interunit Wiring
70 (for Total of Each Room)
25 (for One Room)
Chargeless
15 (between Indoor Unit and Outdoor Unit)
15 (between Indoor Units)
3D050821#1A
Conversion Formulae
1. The data are based on the conditions shown in the table below.
Cooling
Piping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB
7.5m
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
SiEBE12-625
1.3
Specifications
Indoor Units - Heat Pump
Wall Mounted Type
50Hz 230V
FTXG25EV1BW
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
7.7 (271)
6.1 (215)
4.7 (165)
3.8 (134)
9.0 (317)
7.9 (278)
6.7 (236)
5.4 (190)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30-30-30
30-30-30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
7.7 (271)
6.1 (215)
4.7 (165)
3.8 (134)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30-30-30
30-30-30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
38/32/25/22
38/33/28/25
38/32/25/22
38/33/28/25
56
56
56
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051101
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051102
FTXG35EV1BW
Rated Capacity
Front Panel Color
FTXG35EV1BS
Heating
Cooling
3.5kW Class
Mat Crystal White
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
9.0 (317)
7.9 (278)
6.7 (236)
5.4 (190)
dBA
Cooling
m³/min
(cfm)
Heating
2.5kW Class
Mat Crystal Silver
dBA
Model
Fan
Cooling
2.5kW Class
Mat Crystal White
Fan
Air Flow Rates
FTXG25EV1BS
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
8.1 (285)
6.5 (229)
4.9 (173)
4.1 (144)
Heating
5.0kW Class
Mat Crystal Silver
9.6 (338)
8.2 (289)
6.7 (236)
5.9 (208)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30-30-30
30-30-30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
8.1 (285)
6.5 (229)
4.9 (173)
4.1 (144)
9.6 (338)
8.2 (289)
6.7 (236)
5.9 (208)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable / Washable / Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30-30-30
30-30-30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
dBA
39/33/26/23
39/34/29/26
39/33/26/23
39/34/29/26
dBA
57
57
57
57
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051103
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D051104
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
23
Specifications
SiEBE12-625
50Hz 230V
FTXS20D3VMW
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
9.4 (332)
7.6 (268)
5.8 (205)
5.0 (177)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
0.16
35
35
95.1
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
0.16
35
35
95.1
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
38/25/22
38/28/25
38/25/22
38/28/25
56
56
56
56
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051085
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051086
FTXS25D3VMW
Rated Capacity
Front Panel Color
FTXS25D3VML
Heating
Cooling
2.5kW Class
White
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
9.4 (332)
7.6 (268)
5.8 (205)
5.0 (177)
dBA
Cooling
m³/min
(cfm)
Heating
2.0kW Class
Silver Line
dBA
Model
Fan
Cooling
2.0kW Class
White
Fan
Air Flow Rates
FTXS20D3VML
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
Heating
2.5kW Class
Silver Line
9.4 (332)
7.6 (268)
5.8 (205)
5.0 (177)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
0.16
35
35
95.1
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
8.7 (307)
6.7 (237)
4.7 (166)
3.9 (138)
9.4 (332)
7.6 (268)
5.8 (205)
5.0 (177)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.16
0.16
35
35
95.1
95.1
Microcomputer Control
283×800×195
265×855×340
9
12
dBA
38/25/22
38/28/25
38/25/22
38/28/25
dBA
56
56
56
56
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051087
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051088
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
24
Specifications
SiEBE12-625
Specifications
50Hz 230V
FTXS35D3VMW
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
8.9 (314)
6.9 (244)
4.8 (169)
4.0 (141)
9.7 (342)
7.9 (279)
6.0 (212)
5.2 (184)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283×800×195
265×855×340
9
12
8.9 (314)
6.9 (244)
4.8 (169)
4.0 (141)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
283×800×195
265×855×340
9
12
39/26/23
39/29/26
39/26/23
39/29/26
57
57
57
57
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051089
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D051090
FTXS20CAVMB
Rated Capacity
Front Panel Color
FTXS25CAVMB
Heating
Cooling
2.5kW Class
White
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
9.7 (342)
7.9 (279)
6.0 (212)
5.2 (184)
dBA
Cooling
m³/min
(cfm)
Heating
3.5kW Class
Silver Line
dBA
Model
Fan
Cooling
3.5kW Class
White
Fan
Air Flow Rates
FTXS35D3VML
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
7.7 (272)
5.9 (208)
4.2 (148)
3.6 (127)
Heating
2.5kW Class
White
7.8 (275)
6.5 (230)
5.3 (187)
4.6 (162)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
7.7 (272)
5.9 (208)
4.2 (148)
3.6 (127)
7.8 (275)
6.5 (230)
5.3 (187)
4.6 (162)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
0.18
40
40
96.6
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
dBA
38/32/25/22
38/33/28/25
38/32/25/22
38/33/28/25
dBA
56
56
56
56
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050941
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050943
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
25
Specifications
SiEBE12-625
50Hz 230V
FTXS35CAVMB
Model
Cooling
Heating
Rated Capacity
Front Panel Color
Air Flow Rates
3.5kW Class
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
H
M
L
SL
7.7 (272)
6.0 (212)
4.4 (155)
3.8 (134)
Cross Flow Fan
18
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
W
Steps
A
W
%
0.18
40
96.6
Microcomputer Control
273×784×195
258×834×325
7.5
11
dBA
39/33/26/23
dBA
57
39/34/29/26
57
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050945
mm
mm
mm
CTXG50EV1BW
Cooling
Rated Capacity
Front Panel Color
CTXG50EV1BS
Heating
Cooling
5.0kW Class
Mat Crystal White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
0.18
40
96.6
mm
mm
kg
kg
Model
Air Flow Rates
8.1 (286)
6.7 (237)
5.3 (187)
4.6 (162)
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
11.3 (398)
9.1 (320)
7.1 (250)
6.7 (236)
Heating
5.0kW Class
Mat Crystal Silver
12.6 (444)
10.6 (373)
8.7 (306)
7.7 (271)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30
30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
11.3 (398)
9.1 (320)
7.1 (250)
6.7 (236)
12.6 (444)
10.6 (373)
8.7 (306)
7.7 (271)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.15-0.14-0.13
0.15-0.14-0.13
30
30
90.9-93.2-96.2
90.9-93.2-96.2
Microcomputer Control
275×840×150
222×894×345
9
13
dBA
47/41/35/32
47/41/35/32
47/41/35/32
47/41/35/32
dBA
64
64
64
64
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 12.7
φ18.0
3D051105
Both Liquid and Gas Pipes
φ 6.4
φ 12.7
φ18.0
3D051106
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
26
Specifications
SiEBE12-625
Specifications
50Hz 230V
FTXS50D2V1W
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
11.4 (402)
9.3 (328)
7.1 (251)
6.2 (219)
11.4 (402)
9.4 (332)
7.4 (261)
6.3 (222)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.21
0.21
48
48
99.4
99.4
Microcomputer Control
283×800×195
265×855×340
9
12
11.4 (402)
9.3 (328)
7.1 (251)
6.2 (219)
Cross Flow Fan
40
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.21
0.21
48
48
99.4
99.4
Microcomputer Control
283×800×195
265×855×340
9
12
46/41/35/32
46/40/34/31
46/41/35/32
46/40/34/31
62
62
62
62
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D051814
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ15.9
φ18.0
3D051815
FTXS50EV1B
Rated Capacity
Front Panel Color
FTXS60EV1B
Heating
Cooling
5.0kW Class
White
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
11.4 (402)
9.4 (332)
7.4 (261)
6.3 (222)
dBA
Cooling
m³/min
(cfm)
Heating
5.0kW Class
White
dBA
Model
Fan
Cooling
5.0kW Class
White
Fan
Air Flow Rates
FTXS50D2V1L
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
14.7 (519)
12.4 (438)
10.3 (364)
9.5 (335)
Heating
6.0kW Class
White
16.1 (569)
13.9 (491)
11.5 (406)
10.2 (360)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.15
0.16
34
36
98.6
97.8
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
16.2 (572)
13.6 (480)
11.4 (402)
10.2 (360)
17.4 (614)
15.1 (533)
12.7 (448)
11.4 (402)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.18
0.20
40
45
96.6
97.8
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
dBA
43/39/34/31
42/38/33/30
45/41/36/33
44/40/35/32
dBA
59
58
61
60
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D051645
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D051646
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
27
Specifications
SiEBE12-625
50Hz 230V
FTXS71EV1B
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
Cooling
7.1kW Class
White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
FTXS71BAVMB
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
17.4 (614)
14.6 (515)
11.6 (409)
10.6 (374)
Heating
7.1kW Class
White
19.7 (695)
16.6 (586)
13.5 (477)
12.1 (427)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.20
0.22
45
50
97.8
98.8
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
16.7 (590)
14.2 (501)
11.6 (409)
10.6 (374)
18.5 (653)
15.1 (533)
13.5 (477)
12.1 (427)
Cross Flow Fan
43
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.20
0.22
45
50
96.4
97.6
Microcomputer Control
290×1,050×238
337×1,147×366
12
17
dBA
46/42/37/34
46/42/37/34
46/42/37/34
46/42/37/34
dBA
63
63
63
63
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ15.9
φ18.0
3D052803
Both Liquid and Gas Pipes
φ 6.4
φ15.9
φ18.0
3D050880
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
28
Specifications
SiEBE12-625
Specifications
Duct Connected Type
50Hz 230V
FDXS25CAVMB
Model
Cooling
Rated Capacity
Heating
3.5kW Class
—
m³/min
(cfm)
Air Flow Rates
Type
Motor Output
Speed
H
M
L
SL
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
A
W
%
mm
mm
kg
kg
dBA
Pa
mm
mm
mm
9.5 (335)
8.8 (311)
8.0 (282)
6.7 (237)
—
9.5 (335)
8.8 (311)
8.0 (282)
6.7 (237)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.47
0.47
100
100
92.5
92.5
Microcomputer Control
200×900×620
266×1,106×751
25
31
35/33/31/29
35/33/31/29
40
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ 26 / I.D. φ 20)
3D048945C
10.0 (353)
9.3 (328)
8.5 (300)
7.0 (247)
Cooling
Rated Capacity
10.0 (353)
9.3 (328)
8.5 (300)
7.0 (247)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.47
0.47
100
100
92.5
92.5
Microcomputer Control
200×900×620
266×1,106×751
25
31
35/33/31/29
35/33/31/29
40
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ 26 / I.D. φ 20)
3D048946C
FDXS50CVMB
Model
FDXS60CVMB
Heating
Cooling
5.0kW Class
m³/min
(cfm)
Air Flow Rates
Type
Motor Output
Speed
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Note:
Specifications
H
M
L
SL
A
W
%
mm
mm
kg
kg
dBA
Pa
mm
mm
mm
12.0 (424)
11.0 (388)
10.0 (353)
8.4 (297)
—
12.0 (424)
11.0 (388)
10.0 (353)
8.4 (297)
Sirocco Fan
130
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.64
0.64
140
140
95.1
95.1
Microcomputer Control
200×900×620
266×1,106×751
27
34
37/35/33/31
Heating
6.0kW Class
—
Front Panel Color
Fan
Cooling
2.5kW Class
Front Panel Color
Fan
FDXS35CAVMB
Heating
37/35/33/31
40
Both Liquid and Gas Pipes
φ 6.4
φ12.7
VP20 (O.D. φ 26 / I.D. φ 20)
3D052132
16.0 (565)
14.8 (523)
13.5 (477)
11.2 (395)
16.0 (565)
14.8 (523)
13.5 (477)
11.2 (395)
Sirocco Fan
130
5 Steps, Silent, Auto
Removable-Washable-Mildew Proof
0.74
0.74
160
160
94.0
94.0
Microcomputer Control
200×1,100×620
266×1,306×751
30
37
38/36/34/32
38/36/34/32
40
Both Liquid and Gas Pipes
φ 6.4
φ12.7
VP20 (O.D. φ 26 / I.D. φ 20)
3D0452133
1. The operating sound is based on the rear side suction inlet and the external static pressure 40 Pa.
Operating sound for under side suction inlet : [operating sound for rear side suction inlet] +5 dB.
However, when installation to which the external static pressure becomes low is carried out,
5 dB or more may go up.
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
29
Specifications
SiEBE12-625
50Hz 230V
FDXS25EAVMB
Model
Cooling
Rated Capacity
m³/min
(cfm)
Type
Motor Output
Speed
W
Steps
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
External Static Pressure
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Note:
H
M
L
SL
A
W
%
mm
mm
kg
kg
dBA
Pa
mm
mm
mm
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
—
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable / Washable / Mildew Proof
0.48
0.48
71
71
64.3
64.3
Microcomputer Control
200×700×620
274×906×751
21
29
35/33/31/29
Heating
3.5kW Class
—
Air Flow Rates
30
Cooling
2.5kW Class
Front Panel Color
Fan
FDXS35EAVMB
Heating
35/33/31/29
30
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ 26 / I.D. φ 20)
3D051881A
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
8.7 (307)
8.0 (282)
7.3 (258)
6.2 (219)
Sirocco Fan
62
5 Steps, Silent, Auto
Removable / Washable / Mildew Proof
0.48
0.48
71
71
64.3
64.3
Microcomputer Control
200×700×620
274×906×751
21
29
35/33/31/29
35/33/31/29
30
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
VP20 (O.D. φ 26 / I.D. φ 20)
3D051883A
1. The operating sound is based on the rear side suction inlet and the external static pressure 30 Pa.
Operating sound for under side suction inlet : [operating sound for rear side suction inlet] +6 dB.
However, when installation to which the external static pressure becomes low is carried out,
6 dB or more may go up.
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
SiEBE12-625
Specifications
Floor / Ceiling Suspended Dual Type
50Hz 230V
FLXS25BAVMB
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
7.6 (268)
6.8 (240)
6.0 (212)
5.2 (184)
9.2 (325)
8.3 (293)
7.4 (261)
6.6 (233)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.32
0.34
70
74
95.1
94.6
Microcomputer Control
490×1,050×200
566×1,100×280
16
22
8.6 (304)
7.6 (268)
6.6 (233)
5.6 (198)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.36
0.36
78
78
94.2
94.2
Microcomputer Control
490×1,050×200
566×1,100×280
16
22
37/34/31/28
37/34/31/29
38/35/32/29
39/36/33/30
53
—
54
—
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050866
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050868
FLXS50BAVMB
Rated Capacity
Front Panel Color
FLXS60BAVMB
Heating
Cooling
5.0kW Class
Almond White
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
9.8 (346)
8.9 (314)
8.0 (282)
7.2 (254)
dBA
Cooling
m³/min
(cfm)
Heating
3.5kW Class
Almond White
dBA
Model
Fan
Cooling
2.5kW Class
Almond White
Fan
Air Flow Rates
FLXS35BAVMB
Heating
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
11.4 (402)
10.0 (353)
8.5 (300)
7.5 (265)
Heating
6.0kW Class
Almond White
12.1 (427)
9.8 (346)
7.5 (265)
6.8 (240)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.45
0.45
96
96
92.8
92.8
Microcomputer Control
490×1,050×200
280×1,100×566
17
24
12.0 (424)
10.7 (378)
9.3 (328)
8.3 (293)
12.8 (452)
10.6 (374)
8.4 (297)
7.5 (265)
Sirocco Fan
34
5 Steps, Silent, Auto
Right, Left, Horizontal, Downward
Removable-Washable-Mildew Proof
0.47
0.45
98
96
90.7
92.8
Microcomputer Control
490×1,050×200
280×1,100×566
17
24
dBA
47/43/39/36
46/41/35/33
48/45/41/39
47/42/37/34
dBA
63
32
64
63
mm
mm
mm
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D050897
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ18.0
3D050882
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
Specifications
31
Specifications
SiEBE12-625
Floor Standing Type
50Hz 230V
FVXS25BAVMB
Model
Cooling
Rated Capacity
Front Panel Color
Air Flow Rates
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
H
M
L
SL
W
Steps
A
W
%
mm
mm
kg
kg
dBA
dBA
mm
mm
mm
8.1 (286)
6.2 (219)
4.3 (152)
3.4 (120)
Heating
3.5kW Class
Almond White
9.2 (325)
7.0 (247)
4.8 (169)
3.5 (124)
8.3 (293)
6.3 (222)
4.3 (152)
3.4 (120)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
0.14
0.14
32
32
99.4
99.4
Microcomputer Control
600×650×195
714×770×294
13
19
9.2 (325)
7.1 (251)
5.0 (177)
3.6 (127)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
0.14
0.14
32
32
99.4
99.4
Microcomputer Control
600×650×195
714×770×294
13
19
38/32/26/23
38/32/26/23
39/33/27/24
39/34/29/26
54
—
55
—
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050874
Both Liquid and Gas Pipes
φ 6.4
φ 9.5
φ18.0
3D050876
FVXS50BAVMB
Model
Cooling
Rated Capacity
Front Panel Color
Heating
5.0kW Class
Almond White
m³/min
(cfm)
Type
Motor Output
Speed
Air Direction Control
Air Filter
Running Current (Rated)
Power Consumption (Rated)
Power Factor
Temperature Control
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation
H/M/L/SL
Sound
Sound Power H
Heat Insulation
Liquid
Gas
Piping Connection
Drain
Drawing No.
Fan
Cooling
2.5kW Class
Almond White
m³/min
(cfm)
Air Flow Rates
FVXS35BAVMB
Heating
H
M
L
SL
10.8 (381)
9.2 (325)
7.7 (272)
6.7 (237)
Cross Flow Fan
14+14
5 Steps, Silent, Auto
Right, Left, Horizontal, Upward
Removable-Washable-Mildew Proof
W
Steps
A
W
%
mm
mm
kg
kg
dBA
dBA
mm
mm
mm
13.2 (466)
11.3 (399)
9.4 (332)
8.3 (293)
0.26
55
92.0
0.32
70
95.1
Microcomputer Control
600×650×195
714×770×294
13
19
44/40/36/33
45/40/36/33
56
57
Both Liquid and Gas Pipes
φ 6.4
φ12.7
φ20.0
3D050895
Conversion Formulae
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
32
Specifications
SiEBE12-625
1.4
Specifications
Outdoor Units - Heat Pump
50Hz 230V
4MXS68E2(3)V1B
Model
Cooling
Cooling Capacity
kW
Power Consumption
W
Running Current
A
Casing Color
Type
Compressor
Model
Motor Output
Model
Refrigerant Oil
Charge
Type
Refrigerant
Charge
W
L
m³/min
Air Flow Rates
cfm
Fan
Type
Motor Output
Running Current
Power Consumption
Starting Current
Dimensions (H×W×D)
Packaged Dimensions (H×W×D)
Weight
Gross Weight
Operation Sound
Sound Power
Liquid
Gas
Piping Connection
Drain
Heat Insulation
No. of Wiring Connection
Max. Interunit Piping Length
Amount of Additional Charge
Max. Installation Height Difference
kg
H
L
H
L
W
A
W
A
mm
mm
kg
kg
dBA
dBA
mm
mm
mm
m
m
g/m
m
m
Drawing No.
Note:
Specifications
4MXS80DAVMB
Heating
Cooling
Heating
—
—
—
—
—
—
Ivory White
Hermetically Sealed Swing Type
2YC45BXD
1,380
FVC50K
0.75
R-410A
2.6
51
47.6
45
45
1,801
1,681
1,589
1,589
Propeller
53
H: 0.33 / L: 0.25
H: 68 / L: 46
8.5
735×936×300
784×992×390
59
65
48
49
61
62
φ 6.4×4
φ9.5×2, φ12.7×2
φ18.0
Both Liquid and Gas Pipes
3 for Power Supply, 4 for Interunit Wiring
60 (for Total of Each Room)
25 (for One Room)
20 (30m or more)
15 (between Indoor Unit and Outdoor Unit)
7.5 (between Indoor Units)
3D051891#1
Ivory White
Hermetically Sealed Swing Type
2YC45BXD
1,380
FVC50K
0.75
R-410A
3.1
48.5
45
42
42
1,713
1,589
1,483
1,483
Propeller
51
H: 0.44 / L: 0.34
H: 60 / L: 41
8.7
908×900×320
1,025×926×402
73
82
48
49
61
62
φ 6.4×4
φ9.5×2, φ12.7×1, φ15.9×1
φ25.0
Both Liquid and Gas Pipes
3 for Power Supply, 4 for Interunit Wiring
70 (for Total of Each Room)
25 (for One Room)
20 (40m or more)
15 (between Indoor Unit and Outdoor Unit)
7.5 (between Indoor Units)
3D050837#1
1. The data are based on the conditions shown in the table below.
Conversion Formulae
Cooling
Heating
Piping Length
Indoor ; 27°CDB/19°CWB
Outdoor ; 35°CDB
Indoor ; 20°CDB
Outdoor ; 7°CDB/6°CWB
7.5m
kcal/h=kW×860
Btu/h=kW×3414
cfm=m³/min×35.3
33
Specifications
SiEBE12-625
34
Specifications
SiEBE12-625
Part 3
Printed Circuit Board
Connector Wiring Diagram
1. Printed Circuit Board Connector Wiring Diagram..................................36
1.1
1.2
1.3
1.4
1.5
Wall Mounted Type ................................................................................36
Duct Connected Type.............................................................................45
Floor / Ceiling Suspended Dual Type.....................................................47
Floor Standing Type ...............................................................................49
Outdoor Units .........................................................................................52
Printed Circuit Board Connector Wiring Diagram
35
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
1. Printed Circuit Board Connector Wiring Diagram
1.1
Wall Mounted Type
1.1.1
FTK(X)S 20~50 D
Connectors
PCB(1) (Control PCB)
1)
2)
3)
4)
5)
6)
7)
S1
S6
S21
S26
S28
S32
S35
Connector for DC fan motor
Connector for swing motor (horizontal blades)
Connector for centralized control (HA)
Connector for display PCB
Connector for signal receiver PCB
Connector for heat exchanger thermistor
Connector for INTELLIGENT EYE sensor PCB
PCB(2) (Signal Receiver PCB)
1) S29
Connector for control PCB
PCB(3) (Display PCB)
1) S27
Connector for control PCB
PCB(4) (INTELLIGENT EYE sensor PCB)
1) S36
Note:
Connector for control PCB
Other designations
PCB(1) (Control PCB)
1) V1
2) JA
JB
JC
3) LED A
4) FU1
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function (auto-restart)
∗ Refer to page 291 for detail.
LED for service monitor (green)
Fuse (3.15A)
PCB(3) (Display PCB)
1)
2)
3)
4)
5)
36
SW1 (S1W)
LED1
LED2
LED3
RTH1 (R1T)
Forced operation ON / OFF switch
LED for operation (green)
LED for timer (yellow)
LED for INTELLIGENT EYE (green)
Room temperature thermistor
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Printed Circuit Board Connector Wiring Diagram
PCB Detail
PCB(1): Control PCB
V1
S1
FU1
S6
S21
S35
LED A
JA
JB JC
S32
S28
S26
(R4288)
PCB(2): Signal Receiver PCB
PCB(3): Display PCB
S27
SW1
S29
LED1 LED2
(R5183)
LED3
RTH1
(R4290)
PCB(4): INTELLIGENT EYE sensor PCB
S36
(R4291)
Printed Circuit Board Connector Wiring Diagram
37
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
1.1.2 FTK(X)S20~35C
Connectors
1)
2)
3)
4)
5)
6)
7)
8)
9)
Note:
S1
S6
S7
S21
S26
S27
S32
S35
S36
Other designations
1) V1
2) JA
JB
JC
3)
4)
5)
6)
7)
8)
9)
38
Connector for fan motor
Connector for swing motor (Horizontal Flap)
Connector for fan motor
Connector for centralized control to 5 rooms
Connector for signal receiver PCB
Connector for control PCB
Connector for heat exchanger thermistor
Connector for INTELLIGENT EYE Sensor PCB
Connector for control PCB
SW7
LED1
LED2
LED3
LED A
FU1
RTH1
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function
∗ Refer to page 291 for more detail.
Forced operation ON/OFF switch
LED for operation (green)
LED for timer (yellow)
LED for HOME LEAVE operation (red)
LED for service monitor (green)
Fuse (3.15A)
Room temperature thermistor
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Printed Circuit Board Connector Wiring Diagram
PCB
PCB(1) Control
SW7
S1
PCB (2)
Signal reciever
5V Check
V1
5V
S27
S7
JP21
JA
JB
JC
PCB (3)
Intelligent eye
sensor
12V Check
12V
GND
S21
S6
GND
S35
JA
JB
JC
S32
S26
(R2413)
Printed Circuit Board Connector Wiring Diagram
39
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB(1): Control PCB
PCB(2): Signal Receiver PCB
V1
Control PCB
Fu1
S1
Signal Receiver PCB
SW7
LED1
LED2
LED3
RTH1
S27
5V Check
S7
12V Check
S21
S6
GND
S35
LED A
JA
JB
JC
S32
S26
(R4987)
PCB(3): INTELLIGENT EYE sensor PCB (Inverter models only)
S36
(R4988)
40
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Printed Circuit Board Connector Wiring Diagram
1.1.3 FTK(X)S50~71E, FTK(X)S71B
Connectors
1) S1
2) S6
3) S8
4) S21
5) S26, S37
6) S27, S29, S36
7) S28
8) S32
9) S35
10)S38
Note:
Connector for fan motor
Connector for swing motor (horizontal blades)
Connector for swing motor (vertical blades)
Connector for centralized control (HA)
Connector for buzzer PCB
Connector for control PCB
Connector for signal receiver PCB
Connector for heat exchanger thermistor
Connector for Intelligent Eye sensor PCB
Connector for display PCB
Other designations
1) V1
2) JA
JB
JC
3)
4)
5)
6)
7)
8)
9)
SW1
LED1
LED2
LED3
LED A
FU1
RTH1
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function
∗ Refer to page 291 for detail.
Forced operation ON/OFF switch
LED for operation (green)
LED for timer (yellow)
LED for HOME LEAVE operation (red)
LED A for service monitor (green)
Fuse (3.15A)
Room temperature thermistor
Printed Circuit Board Connector Wiring Diagram
41
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB(1): Control PCB (indoor unit)
S1
V1
FU1
S21
S6
S8
S35
LED A
JA
JB JC
PCB(2): Signal Receiver PCB
S32 S28
S26
(R2860)
PCB(3): Buzzer PCB
S27
SW1
S38
S29
(R2861)
RTH1
PCB(4): Display PCB
LED1
LED2
(R2862)
PCB(5): Intelligent Eye sensor PCB
LED3
S37
(R2863)
S36
(R2864)
42
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Printed Circuit Board Connector Wiring Diagram
1.1.4 FTXG25~35E, CTXG50E
Connectors
PCB(1) (Control PCB)
1)
2)
3)
4)
S1
S21
S32
S36
5)
6)
7)
8)
S41
S46
S49
S51
Connector for fan motor
Connector for centralized control (HA)
Connector for heat exchanger thermistor
Connector for INTELLIGENT EYE sensor PCB and control
PCB
Connector for swing motor
Connector for signal receiver PCB
Connector for reduction motor (front panel mechanism)
Connector for front panel limit switch
PCB(2) (Signal Receiver PCB)
1) S47
Connector for control PCB
PCB(3) (INTELLIGENT EYE sensor PCB)
1) S36
Note:
Connector for control PCB
Other designations
PCB(1) (Control PCB)
1) V1
2) JA
JB
JC
3) FU1
4) LED A
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function (auto-restart)
∗ Refer to page 291 for detail.
Fuse (3.15A)
LED for service monitor (green)
PCB(2) (Signal Receiver PCB)
1)
2)
3)
4)
5)
SW1
LED2
LED3
LED4
RTH1
Forced operation ON / OFF switch
LED for INTELLIGENT EYE (green)
LED for timer (yellow)
LED for operation (green)
Room temperature thermistor
Printed Circuit Board Connector Wiring Diagram
43
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB(1): Control PCB (indoor unit)
S1
S49
S41
S51
JB
JA JC
LED A
Adress:Ja
Exit
Cut
V1
S21
FU1
S46
S36
S32
(R4991)
PCB(2): Signal Receiver PCB
S47
RTH1
SW1
LED4
LED2
LED3
(R4992)
PCB(3): INTELLIGENT EYE sensor PCB
S36
(R4988)
44
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
1.2
Printed Circuit Board Connector Wiring Diagram
Duct Connected Type
Connectors
1)
2)
3)
4)
5)
6)
Note:
S1 (on PCB 1)
S1 (on PCB 2)
S7
S21
S26
S32
Other designations
1) V1
2) JA
JB
JC
3)
4)
5)
6)
7)
8)
9)
PCB Detail
Connector for fan motor
Connector for control PCB
Connector for fan motor
Connector for centralized control to 5 rooms
Connector for display PCB
Connector for room temp / heat exchanger thermistor
SW1
LED1
LED2
LED3
LED A
FU1
RTH1
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function
∗ Refer to page 291 for more detail.
Forced operation ON/OFF switch
LED for operation (green)
LED for timer (yellow)
LED for HOME LEAVE operation (red)
LED for service monitor (green)
Fuse (3.15A)
Room temperature thermistor
PCB (1): Control PCB
Fu1
S1
V1
S7
S21
S26
LED A JA
Printed Circuit Board Connector Wiring Diagram
JB JC
S32
2P131149G
45
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB (2): Display PCB
S1
LED3
LED2
PbF
WLU
RTH1
C3
C2
C1
LED1
SW1
2P084375
46
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
1.3
Printed Circuit Board Connector Wiring Diagram
Floor / Ceiling Suspended Dual Type
Connectors
1) S6
2) S7
3) S21
4) S24
5) S25, S27, S36
6) S26
7) S31
8) S32
9) S37
Note:
Other designations
1) V1
2) JA
JB
JC
3)
4)
5)
6)
7)
8)
9)
PCB Detail
Connector for swing motor (horizontal swing)
Connector for fan motor
Connector for centralized control
Connector for display PCB
Connector for control PCB
Connector for signal receiver PCB
Connector for room temperature thermistor
Connector for heat exchanger thermistor
Connector for power supply PCB
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function
∗ Refer to page 291 for detail.
Forced operation ON/OFF switch
Select switch ceiling or floor
LED for operation (green)
LED for timer (yellow)
LED for HOME LEAVE operation (red)
LED for service monitor (green)
Fuse (3.15A)
SW1
SW2
LED1
LED2
LED3
LED A
FU1
PCB (1): Control PCB
S21
Pb Free
LED A
SW2
S26
S7
S6
12V Check
S32
S24
JC
JB
5V Check
S37
GND
JA
Printed Circuit Board Connector Wiring Diagram
47
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB (2): Power Supply PCB
S36
FU1
Pb Free
V1
PCB (3): Display PCB
Pb Free
LED2
LED3
LED1
S25
PCB (4): Signal Receiver PCB
SW1
EX511 REV 12
PbF
RTH
I
PHOTO
2P084377-1
S31(RTH)
48
S27
3
SW1
C1
C2
WLU C3
(R4977)
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
1.4
Printed Circuit Board Connector Wiring Diagram
Floor Standing Type
Connectors
1) S6
2) S21
3) S23
4) S31, S32
5) S201, S203,
S7, S24, S26
6) S202, S204,
S8
7) S25
8) S301, S302
Note:
Connector for swing motor and lower air outlet motor
Connector for centralized control
Connector for signal receiver
Connector for room temperature / heat exchanger thermistor
Connector for power supply PCB (1)
Connector for control PCB (2)
Connector for display PCB (3)
Connector for fan motors
Other Designations
1) V1
2) JA
JB
JC
3) SW1
4) SW2
5) SW4
6) FU
7) LED11
8) LED12
9) LED14
10)LED A
Varistor
Address setting jumper
Fan speed setting when compressor is OFF on thermostat
Power failure recovery function
∗ Refer to page 291 for detail.
Forced operation ON/OFF switch
Changing upward air flow limit switch
Discharge changeover switch
Fuse (3.15A)
LED for operation (green)
LED for timer (yellow)
LED for HOME LEAVE operation (red)
LED for service monitor (green)
Printed Circuit Board Connector Wiring Diagram
49
Printed Circuit Board Connector Wiring Diagram
PCB Detail
SiEBE12-625
PCB (1): Power Supply PCB (25, 35 class)
S202
S8
PCB Detail
50
S204
PCB (1): Power Supply PCB (50 class)
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
PCB Detail
Printed Circuit Board Connector Wiring Diagram
PCB (2): Control PCB
PCB (3): Display PCB
PCB (4): Signal Receiver PCB
Pb Free
Pb Free
LED 14
LED 12
Pb Free
LED 11
LED A
Printed Circuit Board Connector Wiring Diagram
51
Printed Circuit Board Connector Wiring Diagram
1.5
SiEBE12-625
Outdoor Units
Connectors
1) S10
2) S20
3) S21
4) S22
5) S23
6) S31
7) S32
8) S33
9) S40
10) S51
11) S52
12) S71
13) S80
14) S90
15) S91
16) S92
17) S93
18) S101
19) S102
20) AC1
21) AC2
22) E
23) H1, H2
24) LED A, LED1 to 4
25) FU2
26) V2, V5
Connector for S11 on MID1
Connector for electronic expansion valve coil A port
Connector for electronic expansion valve coil B port
Connector for electronic expansion valve coil C port
Connector for electronic expansion valve coil D port
Connector for CN14 on SPM
Connector for CN11 on SPM
Connector for S34 on inverter PCB (MID2)
Connector for overload protector
Connector for S52 on service monitor PCB
Connector for S51 on PCB
Connector for S72 on inverter PCB (MID2)
Connector for four way valve coil
Connector for thermistors
(outdoor air, heat exchanger, and discharge pipe)
Connector for fin thermistor
Connector for gas pipe thermistor
Connector for liquid pipe thermistor
Connector for S102 on service monitor PCB
Connector for S101 on PCB
Connector for HL on MID1
Connector for HN on MID1
Connector for earth
Connector for diode bridge
Service monitor LED
Fuse (3.15 A)
Varistor
1) S11
2) FU1
3) V3
4) HE
5) HL
6) HN
Connector for S10 on PCB
Fuse (30A)
Varistor
Connector for earth
Connector for AC1 on PCB
Connector for AC2 on PCB
1) S34
2) S70
3) S72
4) FU201
5) N, U, V, W
Connector for S33 on PCB
Connector for fan motor
Connector for S71 on PCB
Fuse (3.15A)
Connector for compressor
MID 1
Inverter PCB
(MID 2)
52
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Printed Circuit Board Connector Wiring Diagram
SPM
1) CN11
2) CN14
3) L1, L2
PCB Detail
S102
Connector for S32 on PCB
Connector for S31 on PCB
Connector for reactor
PCB (1): Control PCB
AC1 E
V2
AC2
V5
FU2
H1
S52
H2
LED A
LED 1
LED 2
LED 3
LED 4
S32
S10
S33
S51
S71
S101
S31
S80
S23
S93
S22
S21 S92 S20 S90 S40
S91
2P138922
MID1
V3
FU1
HL
S11
HN
HE
3P080081
Printed Circuit Board Connector Wiring Diagram
53
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Inverter PCB (MID2)
S72
W
V
U
N
S34
S70
FU201
(3.15A)
3P080085
SPM
CN14
L2
54
L1
CN11
3EB10032
Printed Circuit Board Connector Wiring Diagram
SiEBE12-625
Part 4
Function and Control
1. Main Functions......................................................................................56
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
1.11
1.12
1.13
Frequency Principle................................................................................56
Power-Airflow Dual Flaps, Wide Angle Louvers and Auto-Swing ..........58
Operation Starting Control......................................................................60
Fan Speed Control for Indoor Units........................................................61
Programme Dry Function .......................................................................62
Automatic Operation...............................................................................63
Thermostat Control.................................................................................64
Night Set Mode.......................................................................................65
ECONO Mode ........................................................................................66
INTELLIGENT EYE (Wall Mounted Type only) ......................................67
HOME LEAVE Operation .......................................................................69
Inverter POWERFUL Operation .............................................................70
Other Functions......................................................................................71
2. Function of Main Structural Parts..........................................................73
2.1 Main Structural Parts..............................................................................73
2.2 Function of Thermistor ...........................................................................74
3. Control Specification .............................................................................78
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
3.12
3.13
3.14
3.15
3.16
Function and Control
Mode Hierarchy ......................................................................................78
Frequency Control..................................................................................79
Controls at Mode Changing / Start-up....................................................81
Discharge Pipe Control ..........................................................................82
Input Current Control..............................................................................82
Freeze-up Protection Control .................................................................83
Heating Peak-cut Control .......................................................................83
Fan Control.............................................................................................84
Liquid Compression Protection Function 2.............................................84
Defrost Control .......................................................................................85
Low Hz High Pressure Limit ...................................................................86
Electronic Expansion Valve Control .......................................................86
Malfunctions ...........................................................................................90
Forced Operation Mode .........................................................................91
Wiring-Error Check.................................................................................92
Additional Function.................................................................................94
55
Main Functions
SiEBE12-625
1. Main Functions
Note:
1.1
See the list of functions for the functions applicable to different models.
Frequency Principle
Main Control
Parameters
The compressor is frequency-controlled during normal operation. The target frequency is set by
the following 2 parameters coming from the operating indoor unit:
„ The load condition of the operating indoor unit
„ The difference between the room temperature and the set temperature
Additional
Control
Parameters
The target frequency is adapted by additional parameters in the following cases:
„ Frequency restrictions
„ Initial settings
„ Forced cooling / heating operation
Inverter Principle
To regulate the capacity, a frequency control is needed. The inverter makes it possible to vary
the rotation speed of the compressor. The following table explains the conversion principle:
Phase
1
2
The following drawing shows a schematic view of the inverter principle:
Refrigerant circulation rate (high)
high speed
DC
power
Amount of heat
exchanged air (large)
AC
power
Drawing of
Inverter
Description
The supplied AC power source is converted into the DC power source for the present.
The DC power source is reconverted into the three phase AC power source with variable
frequency.
„ When the frequency increases, the rotation speed of the compressor increases resulting
in an increased refrigerant circulation. This leads to a higher amount of the heat
exchange per unit.
„ When the frequency decreases, the rotation speed of the compressor decreases
resulting in a decreased refrigerant circulation. This leads to a lower amount of the heat
exchange per unit.
Amount of heat
exchanged air (small)
high f
low f
Amount of heat
exchanged air (sm
low speed
50 Hz
freq=
constant 60 Hz
freq=variable
capacity=
variable
Refrigerant circulation rate (low)
56
Amount of heat
exchanged air (larg
(R2812)
Function and Control
SiEBE12-625
Inverter Features
Main Functions
The inverter provides the following features:
„ The regulating capacity can be changed according to the changes in the outdoor air
temperature and cooling / heating load.
„ Quick heating and quick cooling
The compressor rotational speed is increased when starting the heating (or cooling). This
enables a quick set temperature.
Air discharge
temperature
45˚C
inverter
normal heat pump
Start
60
120
300
seconds
(R1187)
„ Even during extreme cold weather, the high capacity is achieved. It is maintained even when
the outdoor air temperature is 2°C.
„ Comfortable air conditioning
A detailed adjustment is integrated to ensure a fixed room temperature. It is possible to air
condition with a small room temperature variation.
„ Energy saving heating and cooling
Once the set temperature is reached, the energy saving operation enables to maintain the
room temperature at low power.
Frequency Limits
The following table shows the functions that define the minimum and maximum frequency:
Frequency limits
Low
High
Forced Cooling /
Heating Operation
Function and Control
„
„
„
„
„
„
Limited during the activation of following functions
Four way valve operation compensation. Refer to page 81.
Input current control. Refer to page 82.
Compressor protection function. Refer to page 81.
Heating Peak-cut control. Refer to page 83.
Freeze-up protection. Refer to page 83.
Defrost control. Refer to page 85.
For more information, refer to “Forced operation mode” on page 91.
57
Main Functions
1.2
SiEBE12-625
Power-Airflow Dual Flaps, Wide Angle Louvers and
Auto-Swing
Power-airflow
Dual Flaps
The large flaps send a large volume of air downwards to the floor. The flap provides an optimum
control area in cooling, heating and dry mode.
Heating Mode
During heating mode, the large flap enables direct warm air straight downwards. The flap
presses the warm air above the floor to reach the entire room.
Cooling Mode
During cooling mode, the flap retracts into the indoor unit. Then, cool air can be blown far and
pervaded all over the room.
Wide-Angle
Louvers
Auto-Swing
The louvres, made of elastic synthetic resin, provide a wide range of airflow that guarantees a
comfortable air distribution.
In case of FTK(X)S20-50D
The following table explains the auto swing process for heating, cooling, dry and fan :
Cooling / Dry
Vertical Swing (up and down)
Heating
5°
10°
45 °
50°
30°
70°
65°
(R4282)
(R4281)
3-D Airflow
Horizontal Swing
(right and left: manual)
Fan
°
45
(R4284)
(R4283)
FTXG25-35E, CTXG50E, FTK(X)S50-71E, FTK(X)S71B
„ Alternative repetition of vertical and horizontal swing motions enables uniform airconditioning of the entire room. This function is effective for starting the air conditioner.
„ When the horizontal swing and vertical swing are both set to auto mode, the airflow become
3-D airflow and the horizontal swing and vertical swing motions are alternated. The order of
swing motion is such that it turns counterclockwise, starting from the right upper point as
viewed to the front side of the indoor unit.
(R1024)
COMFORT
AIRFLOW Mode
FTXG25-35E, CTXG50E
The vertical swing flap is controlled not to blow the air directly on the person in the room.
„ The airflow rate is set to AUTOMATIC.
„ The airflow rate has the upper limit (M tap) in heating mode.
„ The latest command has the priority between POWERFUL and COMFORT AIRFLOW.
Heating
Cooling, Dry
5˚
80˚
(R3297)
58
(R3298)
Function and Control
SiEBE12-625
Main Functions
FTK(X)S20-50D
The vertical swing flap is controlled not to blow the air directly on the person in the room.
„ The airflow rate is controlled automatically within the following steps.
Cooling: L tap – MH tap (same as AUTOMATIC)
Heating: ML tap – M tap
„ The latest command has the priority between POWERFUL and COMFORT AIRFLOW.
Heating
Cooling
5°
70°
(R4303)
Function and Control
(R4302)
59
Main Functions
1.3
SiEBE12-625
Operation Starting Control
FTXG25-35E, CTXG50E
The system carries out the following control at the beginning to conduct every functional parts
properly.
1. Opening the front panel fully
2. Output of the ΔD signal after the front panel starts moving
3. Opening the flap fully after the front panel opens fully
4. Making the fan rotate when the flap passes over the fan-banned area
Control Flow
Start
Opening the front panel
fully
Opening the flap fully
Output of the ΔD signal after
the front panel starts moving
Making the fan rotate when
the flap passes over the
fan-banned area
Running
(R3311)
Timing Chart
Start
OFF
Operation
starting control
ON
Fully close
Front
panel
Fully open
Fully open
Flap
Fan-banned area
Under running control
Fully close
Right
Louvers
Under running control
Left
ON
Fan
Under operation mode control
OFF
Output
Under operation mode control
ΔD
Δ0
TDELTA
Force supply
(from the
outdoor unit)
ON
The outdoor unit provides force
when it receives the ΔD signal.
OFF
(R3312)
60
Function and Control
SiEBE12-625
1.4
Main Functions
Fan Speed Control for Indoor Units
Control Mode
The airflow rate can be automatically controlled depending on the difference between the set
temperature and the room temperature. This is done through phase control and Hall IC control.
For more information about Hall IC, refer to the troubleshooting for fan motor on page 204.
Phase Steps
Phase control and fan speed control contains 9 steps: LLL, LL, SL, L, ML, M, MH, H and HH.
FTXG25/35E
CTXG50E
FTK(X)S50-71E
FTK(X)S71B
Step
Cooling Heating Cooling Heating Cooling
LLL
LL
SL
L
ML
M
MH
(R6037)
(R6035)
(R6035)
(R6036)
(R6036)
H
HH (Powerful) H+70
H+50
H+50
H+50
H+90
FTK(X)S20-50D
FTK(X)S20-35CA
FDK(X)S25-35EA
FDK(X)S25-35CA
FDK(X)S50-60C
FVK(X)S25-50BA
FLK(X)S25-60BA
Heating Cooling Heating
(R6037)
(R6036)
H+90
(R6036)
H+50
H+50
= Within this range the airflow rate is automatically controlled when the FAN setting
button is set to automatic.
Note:
1. Fan stops during defrost operation.
2. In time of thermostat OFF, the fan rotates at the following speed.
Cooling : The fan keeps rotating at the set tap.
Heating : The fan stops.
Automatic Air
Flow Control for
Heating
On heating mode, the indoor fan speed will be regulated according to the indoor heat exchanger
temperature and the difference between the room temperature and the required set point.
Automatic Air
Flow Control for
Cooling
The following drawing explains the principle of fan speed control for cooling:
fan speed
M
+2˚C
ML
+1.5˚C
L
Difference between room
and set temperature
+1˚C
+0.5˚C
Thermostat
setting
temperature
Function and Control
DC motor: Rotation speed control
AC motor: Phase control
(R4594)
61
Main Functions
1.5
SiEBE12-625
Programme Dry Function
Programme dry function removes humidity while preventing the room temperature from
lowering.
Since the microcomputer controls both the temperature and air flow volume, the temperature
adjustment and fan adjustment buttons are inoperable in this mode.
In Case of
Inverter Units
The microcomputer automatically sets the temperature and fan settings. The difference
between the room temperature at startup and the temperature set by the microcomputer is
divided into two zones. Then, the unit operates in the dry mode with an appropriate capacity for
each zone to maintain the temperature and humidity at a comfortable level.
Room temperature at
startup
Temperature (ON point) Frequency switching
at which operation starts point
temperature at
24°C Room
startup
18°C
Temperature difference
for operation stop
1.5°C
0.5°C
18°C
1.0°C
17°C
—
ON point
Frequency
switching
point
0.5˚C
OFF point
5 min
5 min
Compressor
control
LHz
Stop
*55Hz
Indoor unit fan
Extra-low air flow
Low air flow
LHz
Stop
Extra-low air flow
Stop
LHz
Stop
*55Hz
Stop
Stop
Low air flow
LHz indicates low frequency. Item marked with varies depending on models.
(R1359)
62
Function and Control
SiEBE12-625
1.6
Main Functions
Automatic Operation
Automatic Cooling / Heating Function (Heat Pump Only)
When the AUTO mode is selected with the remote controller, the microcomputer automatically
determines the operation mode from cooling and heating according to the room temperature
and setting temperature at the time of the operation startup, and automatically operates in that
mode.
The unit automatically switches the operation mode to cooling or heating to maintain the room
temperature at the main unit setting temperature.
Detailed
Explanation of
the Function
1. Remote controller setting temperature is set as automatic cooling / heating setting
temperature (18 to 30°C).
2. Main unit setting temperature equals remote controller setting temperature plus correction
value (correction value / cooling: 0 deg, heating: 0 deg.).
3. Operation ON / OFF point and mode switching point are as follows.
1 Heating → Cooling switching point:
Room temperature ≥ Main unit setting temperature +2.5 deg.
2 Cooling → Heating switching point:
Room temperature < Main unit setting temperature –2.5 deg.
3 Thermostat ON / OFF point is the same as the ON / OFF point of cooling or heating
operation.
4. During initial operation
Room temperature ≥ Remote controller setting temperature: Cooling operation
Room temperature < Remote controller setting temperature: Heating operation
Heating /
cooling switching point
2.5 deg.
or higher
(Heating thermostat
OFF point)
Main unit setting
temperature
(Cooling thermostat
OFF point)
Cooling /
heating switching point
(1.5 deg.)
or higher
Less than
(1.5 deg.)
Cooling
operation
Heating
operation
Cooling
operation
2.5 deg.
or higher
With compressor capacity supplied
With no compressor capacity supplied
(R1360)
Function and Control
63
Main Functions
1.7
SiEBE12-625
Thermostat Control
Thermostat control is based on the difference between the room temperature and the setpoint.
Thermostat OFF Condition
Š The temperature difference is in the zone A.
Thermostat ON Condition
Š The temperature difference is above the zone C after being in the zone A.
Š The system resumes from defrost control in any zones except A.
Š The operation turns on in any zones except A.
Š The monitoring time has passed while the temperature difference is in the zone B.
(Cooling / Dry : 10 minutes, Heating : 10 seconds)
Cooling / Dry
Š Wall Mounted Type
Room temperature - setpoint
ON
Cooling : -0.5˚C
Dry : -0.5˚C
C
B
Cooling : -2.0˚C
Dry : -2.5~-2.0˚C
A
OFF
(R4668)
Š Floor standing Type
Š Floor/Ceiling suspended Type
Š Duct Connected Type
Room temperature - setpoint
ON
Cooling : -1.0˚C
Dry : -1.0˚C
C
-1.5˚C
B
Cooling : -2.0˚C
Dry : -2.5~-2.0˚C
A
OFF
(R6032)
Heating
Š Wall Mounted Type
Room temperature - setpoint
OFF
A
1.5˚C
B
C
0˚C
ON
(R4669)
Š Floor standing Type
Š Floor/Ceiling suspended Type
Š Duct Connected Type
Room temperature - setpoint
OFF
A
1.5˚C
B
1.0˚C
C
0.5˚C
ON
(R6033)
64
Function and Control
SiEBE12-625
1.8
Main Functions
Night Set Mode
When the OFF timer is set, the Night Set circuit automatically activates.
The Night Set circuit maintains the airflow setting made by users.
The Night Set
Circuit
The Night Set circuit continues heating or cooling the room at the set temperature for the first
one hour, then automatically raises the temperature setting slightly in the case of cooling, or
lowers it slightly in the case of heating, for economical operations. This prevents excessive
heating in winter and excessive cooling in summer to ensure comfortable sleeping conditions,
and also conserves electricity.
Cooling
Operation
훽
0.5°C
훾
0.5°C
1 hour
훾:
Temperature
setting
Operation stops
at the set hours
훽 +0.5°C temperature shift
훾 Temperature setting remains the same
When outside temperature is normal and
room temperature is at set temperature.
When outside temperature is high (27°C or higher).
Timer operation
Night Set Circuit ON
훽:
30 ;inutes
Temperature
setting +1°C
Temperature
setting +0.5°C
+0.5°C
temperature shift
In case of FTXG25-35E, CTXG50E, FTK(X)S20-50D the temperature rises once.
Temperature
setting +0.5°C
0.5°C
1 hour
+0.5°C
temperature shift
Temperature
setting
Operation stops
at the set hours
Timer operation
Night Set Circuit ON
Heating
Operation
2°C
Thermostat
setting
Timer operation
Night Set Circuit ON
Function and Control
1 hour later
65
Main Functions
1.9
Outline
SiEBE12-625
ECONO Mode
FTK(X)S20-50D
The "ECONO mode" reduces the maximum operating current and power consumption by
approx. 30% during start up etc..
This mode is particularly convenient for energy-saving-oriented users. It is also a major bonus
for those whose breaker capacities do not allow the use of multiple electrical devices and air
conditioners.
It is easily activated from the wireless remote controller by pushing the ECONO button.
„ When this function is ON, the maximum capacity is also down. (Approx. 20%)
„ This function can only be set when the unit is running. Pressing the operation stop button
causes the settings to be canceled.
„ This function and POWERFUL operation cannot be used at the same time. The latest
command has the priority.
Power
consumption
and current
Approx.
Normal
30%
Econo Mode
Time
(R4607)
Details
66
„ ECONO mode can be activated while the unit is running. The remote controller can send the
ECONO command when the unit is in COOL, HEAT, DRY, or AUTO operation.
„ When the ECONO command is valid, the upper limit of frequency is restricted.
Function and Control
SiEBE12-625
Main Functions
1.10 INTELLIGENT EYE (Wall Mounted Type Only)
This is the function that detects existence of humans in the room by a human motion sensor
(INTELLIGENT EYE) and reduces the capacity when there is no human in the room in order to
save electricity.
Processing
1. Detection method by Intelligent Eye
sampling (20msec)
Sensor output
1sec
If the sensor detects the outputs 10 times/sec.
or more, it judges humans exist.
High
Low
(Human motion)
Human detection ON
signal
OFF
(R2821)
„ This sensor detects human motion by receiving infrared rays and displays the pulse wave
output.
„ A microcomputer in an indoor unit carries out a sampling every 20 msec. and if it detects 10
cycles of the wave in one second in total (corresponding to 20msec.× 10 = 100msec.), it
judges human is in the room as the motion signal is ON.
2. The motions (for example: in cooling)
within 20
minutes.
20 min.
20 min.
40 min.
Human detection ON
signal
OFF
RESET.
Cooling : Set temp. + 2˚C
Heating : Set temp. - 2˚C
Set temp.
Frequency at set temp. + 2˚C
MaxHz
Compressor Mi nHz
speed
0Hz
The lower limit by detecting
human.
(Prohibition of thermostat-off)
in case of
thermostat-off
Remote controller
Intelligent Eye
ON
button
OFF
Operation
ON
OFF
Fan speed ( 1)
Set speed
Set speed
Set speed - 50 rpm
OFF
(R2822)
„ When a microcomputer doesn’t have a signal from the sensor in 20 minutes, it judges that
nobody is in the room and operates the unit in temperature shifted 2°C from the set
temperature. (Cooling : 2°C higher, Dry: 1°C higher and Auto : according to the operation
mode at that time.)
H1 In case of Fan mode, the fan speed reduces by 50 rpm.
Function and Control
67
Main Functions
SiEBE12-625
„ Since the set temperature is shifted by 2°C higher for 40 minutes, compressor speed
becomes low and can realize energy saving operation. But as thermostat is prone to be off
by the fact that the set temperature has been shifted, the thermostat-off action is prohibited
in 40 minutes so as to prevent this phenomena.
After this 40 minutes, the prohibition of the thermostat-off is cancelled and it can realize the
conditions to conduct thermostat-off depending on the room temperature. In or after this forty
minutes, if the sensor detects human motion detection signal, it let the set temperature and
the fan speed return to the original set point, keeping a normal operation.
Others
68
„ The dry operation can’t command the setting temperature with a remote controller, but
internally the set temperature is shifted by 1°C.
Function and Control
SiEBE12-625
Main Functions
1.11 HOME LEAVE Operation
Outline
In order to respond to the customer's need for immediate heating and cooling of the room after
returning home or for house care, a measure to switch the temperature and air volume from that
for normal time over to outing time by one touch is provided. (This function responds also to the
need for keeping up with weak cooling or heating.)
This time, we seek for simplicity of operation by providing the special temperature and air
volume control for outing to be set by the exclusive button.
The SkyAir indoor models also have the function.
Detail of the
Control
1. Start of Function
The function starts when the [HOME LEAVE] button is pressed in cooling mode or heating
mode (including stopping and powerful operation). If this button is pressed while the operation is
stopped, the function becomes effective when the operation is started. If this button is pressed
in powerful operation, the powerful operation is reset and this function becomes effective.
„ The [HOME LEAVE] button is ineffective in dry mode and fan mode.
2. Details of Function
A mark representing [HOME LEAVE] is indicated on the liquid crystal display of the remote
controller. The indoor unit is operated according to the set temperature and air volume for
HOME LEAVE which were pre-set in the memory of the remote controller.
The LED (Red) of indoor unit representing [HOME LEAVE] lights up. (It goes out when the
operation is stopped.)
3. End of Function
The function ends when the [HOME LEAVE] button is pressed again during [HOME LEAVE]
operation or when the powerful operation button is pressed.
Scene <cooling>
“Home leave
operation”
set temp.
Home leave operation
Set temp.
Normal operation
Normal operation
Time
Start “Home leave operation”
Stop “Home leave operation”
Scene <Heating>
“Home leave
operation”
set temp.
Home leave operation
Set temp.
Normal operation
Normal operation
Time
Start “Home leave operation”
Others
Function and Control
Stop “Home leave operation”
The set temperature and set air volume are memorized in the remote controller. When the
remote controller is reset due to replacement of battery, it is necessary to set the temperature
and air volume again for [HOME LEAVE].
69
Main Functions
SiEBE12-625
1.12 Inverter POWERFUL Operation
Outline
In order to exploit the cooling and heating capacity to full extent, operate the air conditioner by
increasing the indoor fan rotating speed and the compressor frequency.
Details of the
Control
When POWERFUL button is pushed in each operation mode, the fan speed / setting
temperature will be converted to the following states in a period of twenty minutes.
In case of FTK(X)S20-50D
Operation mode
COOL
DRY
Fan speed
H tap + 50 rpm
Dry rotating speed +
50 rpm
HEAT
FAN
AUTO
H tap + 50 rpm
H tap + 50 rpm
Same as cooling /
heating in Powerful
operation
Target set temperature
18°C
Normally targeted
temperature in dry
operation; Approx. –2°C
30°C
—
The target is kept
unchanged
Ex.) : Powerful operation in cooling mode.
Target temp.
Set temp.
It should be the lower limit of cooling temperature.
18˚C
Powerful ON
It counts 20 min. also in the remote controller.
Powerful OFF
Fan
50rpm
H tap
Set tap
20min.
Ending condition: "or" in 1 to 3
1. After the lapse of 20 minutes.
2. Stop
3. Powerful operation is OFF.
(R4560)
Refer to “Fan Speed control” on page 61 for detail.
70
Function and Control
SiEBE12-625
Main Functions
1.13 Other Functions
1.13.1 Hot Start Function
Heat Pump Only
In order to prevent the cold air blast that normally comes when heating is started, the
temperature of the heat exchanger of the indoor unit is detected, and either the air flow is
stopped or is made very weak thereby carrying out comfortable heating of the room.
*The cold air blast is also prevented using a similar control when the defrosting operation is
started or when the thermostat gets turned ON.
Heat exchanger
[Reference] temperature zone
[36˚C]
[36˚C]
[34˚C]
[33˚C]
[25˚C]
[20˚C]
F WRB5[W5W]
G
E WRB4[W4W]
F
free or WRB5
D WRB3[W3W]
E
free or WRB5 or WRB4
C WRB2[W2]
D
B WRB1[W1]
C
WRB2
B
WRB1
[8˚C]
[3˚C]
up
G limit free
A W0
A
down
1.13.2 Signal Receiving Sign
When the indoor unit receives a signal from the remote controller, the unit emits a signal
receiving sound.
1.13.3 ON/OFF Button on Indoor Unit
An ON/OFF button is provided on the front panel of the unit. Use this button when the remote
controller is missing or if its battery has run out.
Every press of the button switches from ON to OFF or from OFF to ON.
In case of FTK(X)S20-50D
ON/OFF
ON/OFF button
(R4269)
„ Push this button once to start operation. Push once again to stop it.
„ This button is useful when the remote controller is missing.
„ The operation mode refers to the following table.
Cooling Only
Heat Pump
Mode
COOL
AUTO
Temperature setting
22°C
25°C
Air flow rate
AUTO
AUTO
„ In the case of multi system operation, there are times when the unit does not activate with
this button.
1.13.4 Titanium Apatite Photocatalytic Air-Purifying Filter
This filter combines the Air Purifying Filter and Titanium Apatite Photocatalytic Deodorizing
Filter in a single highly effective unit. The filter traps microscopic particles, decompose odours
and even deactivates bacteria and viruses. It lasts for three years without replacement if
washed about once every six months.
Function and Control
71
Main Functions
SiEBE12-625
1.13.5 Photocatalytic Deodorizing Filter
Photocatalytic Deodorizing Filter demonstrates powerful oxidation characteristics when
subjected to harmless ultraviolet light. Photocatalytic deodorizing power is recovered simply by
exposing the filter to the sun for 6 hours once every 6 months.
1.13.6 Air-Purifying Filter
A double structure made up of a bacteriostatic filter and an Air-Purifying Filter traps dust,
mildew, mites, tobacco smoke, and allergy-causing pollen. Replace the Air-Purifying Filter once
every 3 months.
1.13.7 Air Purifying Filter with Photocatalytic Deodorizing Function
This filter incorporates the benefits the Air Purifying Filter and Photocatalytic Deodorizing Filter
in a single unit. Combining the two filters in this way increases the active surface area of the
new filter. This larger surface area allows the filter to effectively trap microscopic particles,
decompose odours and deactivate bacteria and viruses even for the high volume of air required
to air-condition large living rooms. The filter can be used for approximately 3 years if periodic
maintenance is performed.
1.13.8 Mold Proof Air Filter
The filter net is treated with mold resisting agent TBZ (harmless, colorless, and odorless). Due
to this treatment, the amount of mold growth is much smaller than that of normal filters.
1.13.9 Self-Diagnosis Digital Display
The microcomputer continuously monitors main operating conditions of the indoor unit, outdoor
unit and the entire system. When an abnormality occur, the LCD remote controller displays error
code. These indications allow prompt maintenance operations.
1.13.10Auto-restart Function
Even if a power failure (including one for just a moment) occurs during the operation, the
operation restarts in the condition before power failure automatically when power is restored.
(Note) It takes 3 minutes to restart the operation because the 3 minute stand-by function is
activated.
72
Function and Control
SiEBE12-625
Function of Main Structural Parts
2. Function of Main Structural Parts
2.1
Main Structural Parts
Heat Pump Model
Expansion valve
EVA
EVB
EVC
EVD
SV
D
Solenoid valve
Four way valve
(R4595)
Compressor
Cooling Only
Model
Expansion valve
EVA
EVB
EVC
EVD
Compressor
Note:
Function and Control
(R4596)
Expansion Valve : In Case of 2MK(X).....EVA-B, 3MK(X).....EVA-C, 4MK(X).....EVA-D
73
Function of Main Structural Parts
2.2
SiEBE12-625
Function of Thermistor
2.2.1 Heat Pump Model
E
Expansion valve
EVA
A
EVB
EVC
EVD
SV
D
Solenoid valve
Four way valve
D
B
Compressor
C
(R4600)
A Outdoor Heat
Exchanger
Thermistor
1. The outdoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The outdoor heat exchanger thermistor is used for detecting disconnection of the discharge
thermistor when cooling.
When the discharge pipe temperature becomes lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
B Discharge
Pipe Thermistor
1. The discharge pipe thermistor is used for controlling temperature of the discharge pipe.
If the temperature of discharge pipe (used in place of the inner temperature of the
compressor) rises abnormally, the operating frequency drops or the operation halts.
2. The discharge pipe thermistor is used for detecting disconnection of the discharge
thermistor.
C Gas Pipe
Thermistor
1. In cooling, the gas pipe thermistors are used for gas pipe isothermal control.
The system controls electronic expansion valve opening so that gas pipe temperature in
each room becomes equal.
74
Function and Control
SiEBE12-625
Function of Main Structural Parts
D Indoor Heat
Exchanger
Thermistor
1. The indoor heat exchanger thermistors are used for controlling target discharge
temperature.
The system sets a target discharge pipe temperature according to the outdoor and indoor
heat exchanger temperature, and controls the electronic expansion valve opening so that
the target discharge temperature can be obtained.
2. The indoor heat exchanger thermistors are used for preventing freezing.
During the cooling operation, if the temperature drops abnormally, the operating frequency
becomes lower, then the operation halts.
3. The indoor heat exchanger thermistors are used for anti-icing control.
During the cooling operation, if the heat exchanger temperature in the room where operation
is halted becomes -1°C, or if the room temperature - heat exchanger temperature in the
room where operation is halted becomes ≥10°C, it is assumed as icing.
4. During heating: the indoor heat exchanger thermistors are used for detecting disconnection
of the discharge pipe thermistor.
When the discharge pipe temperature becomes lower than the indoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
5. The indoor heat exchanger thermistors are used for detecting incorrect wiring.
During checking incorrect wiring, refrigerant is passed in order from the port A to detect a
heat exchanger temperature, and then wiring and piping will be checked.
6. The indoor heat exchanger thermistors are used for sub-cooling control.
The actual sub-cooling is calculated from the liquid pipe temperature and the heat
exchanger temperature. The system controls the electronic expansion valve opening to
reach the target sub-cooling.
7. The indoor heat exchanger thermistors are used for heating isothermal control of heat
exchanger.
When heating: if the difference in temperature of each room is greater than 8°C, the
electronic expansion valve of the room in which the temperature is higher is opened.
E Liquid Pipe
Thermistor
1. In heating, the liquid pipe thermistors are used for sub-cooling control.
The system calculates the actual sub-cooling with the liquid pipe temperature and the
maximum heat exchanger temperature among all rooms, and controls the opening of the
electronic expansion valve to reach the target sub-cooling.
Function and Control
75
Function of Main Structural Parts
SiEBE12-625
2.2.2 Cooling Only Model
Expansion valve
EVA
EVB
A
EVC
EVD
B
D
Compressor
C
(R4601)
A Outdoor Heat
Exchanger
Thermistor
1. The outdoor heat exchanger thermistor is used for controlling target discharge temperature.
The system sets a target discharge temperature according to the outdoor and indoor heat
exchanger temperature, and controls the electronic expansion valve opening so that the
target discharge temperature can be obtained.
2. The outdoor heat exchanger thermistor is used for detecting disconnection of the discharge
thermistor when cooling.
When the discharge pipe temperature becomes lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor is judged as disconnected.
B Discharge
Pipe Thermistor
1. The discharge pipe thermistor is used for controlling temperature of the discharge pipe.
If the temperature of discharge pipe (used in place of the inner temperature of the
compressor) rises abnormally, the operating frequency drops or the operation halts.
2. The discharge pipe thermistor is used for detecting disconnection of the discharge
thermistor.
C Gas Pipe
Thermistor
1. In cooling, the gas pipe thermistors are used for gas pipe isothermal control.
The system controls electronic expansion valve opening so that gas pipe temperature in
each room becomes equal.
76
Function and Control
SiEBE12-625
D Indoor Heat
Exchanger
Thermistor
Function and Control
Function of Main Structural Parts
1. The indoor heat exchanger thermistors are used for controlling target discharge
temperature.
The system sets a target discharge pipe temperature according to the outdoor and indoor
heat exchanger temperature, and controls the electronic expansion valve opening so that
the target discharge temperature can be obtained.
2. The indoor heat exchanger thermistors are used for preventing freezing.
During the cooling operation, if the temperature drops abnormally, the operating frequency
becomes lower, then the operation halts.
3. The indoor heat exchanger thermistors are used for anti-icing control.
During the cooling operation, if the heat exchanger temperature in the room where operation
is halted becomes -1°C, or if the room temperature - heat exchanger temperature in the
room where operation is halted becomes ≥10°C, it is assumed as icing.
4. The indoor heat exchanger thermistors are used for detecting incorrect wiring.
During checking incorrect wiring, refrigerant is passed in order from the port A to detect a
heat exchanger temperature, and then wiring and piping will be checked.
77
Control Specification
SiEBE12-625
3. Control Specification
3.1
Mode Hierarchy
Outline
There are two modes; the mode selected in user’s place (normal air conditioning mode) and
forced operation mode for installation and providing service.
Detail
1. For heat pump model
There are following modes; stop, cooling (includes drying), heating (include defrosting)
Air conditioner control mode
Forced operating mode
Forced cooling
Forced heating
Check incorrect wiring
Normal operating mode
Cooling
Heating
Defrosting
Stop mode (except for cooling/heating modes by indoor command)
Preheat operation
During C (capacitor) is discharging
Stop
(R1373)
2. For cooling only model
There are following models; stop and cooling (including drying).
Air conditioner control mode
Forced operating mode
Forced cooling
Check incorrect wiring
Normal operating mode
Cooling
Stop mode (except for cooling modes by indoor command)
Preheat operation
During C (capacitor) is discharging
Stop
(R1374)
Note:
Unless specified otherwise, an indoor dry operation command must be regarded as cooling
operation. An indoor fan operation command cannot be made in a multiple indoor unit. (A forced
fan command to the indoor unit from the outdoor unit must be made during forced operation.)
Determine Operating Mode
Judge the operating mode command set by each room in accordance with the instructing
procedure, and determine the operating mode of the system.
The following procedure will be taken as the modes conflict with each other.
*1.The system will follow the mode determined first. (First-push, first-set)
*2.For the rooms set with different mode, select stand-by mode. (Operation lamp flashes)
78
Function and Control
SiEBE12-625
3.2
Control Specification
Frequency Control
Outline
Frequency that corresponds to each room’s capacity will be determined according to the
difference in the temperature of each room and the temperature that is set by the remote
controller.
The function is explained as follows.
1. How to determine frequency.
2. Frequency command from an indoor unit. (The difference between a room temperature and
the temperature set by the remote controller.)
3. Frequency command from an indoor unit. (The ranked capacity of the operating room).
4. Frequency initial setting.
5. PI control.
Frequency changes by PI control < repeats when frequency becomes lower
Command frequency X repeats when frequency becomes lower
Each drooping function
Input current control, etc.
Upper limit frequency
FMAX
Command frequency
Limit frequency
Initial frequency
PI control
Defrost control (*)
Lower limit frequency
FMIN
Each upper limit function
Compressor protection function
Skip control
Target frequency
Each lower limit function
Four-way valve operating compensation, etc. (*)
*; only for heat pump model
(R1375)
Detail
How to Determine Frequency
The compressor’s frequency will finally be determined by taking the following steps.
For Heat Pump Model
1. Determine command frequency
Š Command frequency will be determined in the following order of priority.
1.1 Limiting frequency by drooping function
Š Input current, discharge pipes, low Hz high pressure limit, peak cutting, freeze-up protection,
dew prevention, fin thermistor temperature.
1.2 Limiting defrost control time
1.3 Forced cooling / heating
1.4 Indoor frequency command
2. Determine upper limit frequency
Š Set a minimum value as an upper limit frequency among the frequency upper limits of the
following functions:
Compressor protection, input current, discharge pipes, Low Hz high pressure, peak cutting,
freeze-up protection, defrost.
3. Determine lower limit frequency
Š Set a maximum value as an lower limit frequency among the frequency lower limits of the
following functions:
Four way valve operating compensation, draft prevention, pressure difference upkeep.
4. Determine prohibited frequency
Š There is a certain prohibited frequency such as a power supply frequency.
For Cooling Only Model
1. Determine command frequency
Š Command frequency will be determined in the following order of priority.
1.1 Limiting frequency by drooping function
Input current, discharge pipes, freeze-up protection, dew prevention, fin thermistor temperature.
1.2 Indoor frequency command
Function and Control
79
Control Specification
SiEBE12-625
2. Determine upper limit frequency
Š Set a minimum value as an upper limit frequency among the frequency upper limits of the
following functions:
Compressor protection, input current, discharge pipes, freeze-up protection, dew prevention,
fin thermistor temperature.
3. Determine lower limit frequency
Š Set a maximum value as an lower limit frequency among the frequency lower limits of the
following functions:
Pressure difference upkeep.
4. Determine prohibited frequency
Š There is a certain prohibited frequency such as a power supply frequency.
Indoor Frequency Command (ΔD signal)
The difference between a room temperature and the temperature set by the remote controller
will be taken as the “ΔD signal” and is used for frequency command.
Temperature
difference
0
0.5
1.0
1.5
ΔD
signal
∗Th
OFF
1
2
3
Temperature
difference
2.0
ΔD
signal
4
Temperature
difference
4.0
ΔD
signal
8
Temperature
difference
6.0
ΔD
signal
C
2.5
3.0
3.5
5
6
7
4.5
5.0
5.5
9
A
B
6.5
7.0
7.5
D
E
F
∗Th OFF = Thermostat OFF
Indoor Unit Capacity (S value)
The capacity of the indoor unit is a “S” value and is used for frequency command.
Capacity
2.5 kW
3.5 kW
S value
25
35
Capacity
5.0 kW
6.0 kW
S value
50
60
Frequency Initial Setting
<Outline>
When starting the compressor, or when conditions are varied due to the change of the operating
room, the frequency must be initialized according to the total of a maximum ΔD value of each room
and a total value of Q (ΣQ) of the operating room (the room in which the thermostat is set to ON).
Q value: Indoor unit output determined from indoor unit volume, air flow rate and other factors.
PI Control (Determine Frequency Up / Down by ΔD Signal)
1. P control
Calculate a total of the ΔD value in each sampling time (20 seconds), and adjust the
frequency according to its difference from the frequency previously calculated.
2. I control
If the operating frequency is not change more than a certain fixed time, adjust the frequency
up and down according to the ΣΔD value, obtaining the fixed ΣΔD value.
When the ΣΔD value is small...lower the frequency.
When the ΣΔD value is large...increase the frequency.
3. Limit of frequency variation width
When the difference between input current and input current drooping value is less than 1.5
A, the frequency increase width must be limited.
4. Frequency management when other controls are functioning
Š When each frequency is drooping;
Frequency management is carried out only when the frequency droops.
Š For limiting lower limit
Frequency management is carried out only when the frequency rises.
5. Upper and lower limit of frequency by PI control
The frequency upper and lower limits are set depending on the total of S values of a room.
When low noise commands come from the indoor unit more than one room or when outdoor
unit low noise or quiet commands come from all the rooms, the upper limit frequency must
be lowered than the usual setting.
80
Function and Control
SiEBE12-625
3.3
Control Specification
Controls at Mode Changing / Start-up
3.3.1 Preheating Operation
Outline
Operate the inverter in the open phase operation with the conditions including the preheating
command from the indoor, the outdoor air temperature and discharge pipe temperature.
Detail
Preheating ON Condition
Š When outdoor air temperature is below 10.5°C and discharge pipe temperature is below
10.5°C, inverter in open phase operation starts.
OFF Condition
Š When outdoor air temperature is higher than 12°C or discharge pipe temperature is higher
than 12°C, inverter in open phase operation stops.
3.3.2 Four Way Valve Switching
Outline of heating
operation
Heat Pump Only
During the heating operation current must be conducted and during cooling and defrosting
current must not be conducted. In order to eliminate the switching sound (as the four way valve
coil switches from ON to OFF) when the heating is stopped, the delay switch of the four way
valve must be carried out after the operation stopped.
Detail
The OFF delay of four way valve
Energize the coil for 150 sec after unit operation is stopped.
3.3.3 Four Way Valve Operation Compensation
Outline
Heat Pump Only
At the beginning of the operation as the four way valve is switched, acquire the differential
pressure required for activating the four way valve by having output the operating frequency,
which is more than a certain fixed frequency, for a certain fixed time.
Detail
Staring Conditions
1. When starting compressor for heating.
2. When the operating mode changes from the previous time.
3. When starting compressor for rushing defrosting or resetting.
4. When starting compressor for the first time after the reset with the power is ON.
Set the lower limit frequency to 55 (model by model) Hz for 70 seconds with any conditions 1
through 4 above.
3.3.4 3 Minutes Stand-by
Prohibit to turn ON the compressor for 3 minutes after turning it off.
(Except when defrosting. (Only for Heat Pump Model).)
3.3.5 Compressor Protection Function
When turning the compressor from OFF to ON, the upper limit of frequency must be set as
follows. (The function must not be used when defrosting (only for heat pump model).)
Frequency
FCG 3
FCG 2
FCG 1
2YC45
80
65
55
FCG3
FCG2
FCG1
TCG120 sec TCG200 sec TCG470 sec
Function and Control
Time
(R1376)
81
Control Specification
3.4
SiEBE12-625
Discharge Pipe Control
Outline
The discharge pipe temperature is used as the compressor's internal temperature. If the
discharge pipe temperature rises above a certain level, the operating frequency upper limit is
set to keep this temperature from going up further.
Detail
Zones (typical value)
120°C
111°C
Reset
zone
Stop zone
Drooping zone
109°C
Keep zone
107°C
Return zone
(R4597)
Management within the Zone
Zone
Stop zone
Control contents
When the temperature reaches the stop zone, stop the compressor and
correct abnormality.
Start the timer, and the frequency will be drooping.
Keep the frequency upper limit.
Cancel the frequency upper limit.
Drooping zone
Keep zone
Return / Reset zone
3.5
Input Current Control
Outline
Detect an input current by the CT during the compressor is running, and set the frequency
upper limit from such input current.
In case of heat pump model, this control is the upper limit control function of the frequency
which takes priority of the lower limit of four way valve activating compensation.
Detail
The frequency control will be made within the following zones.
2 Hz drooping
1.0 second after
rushing in the
drooping zone
After 2.5 seconds
Compressor stops
Stop zone
I1
Input current
I 2 drooping
Drooping zone
keep zone
I3
Reset zone
(R4598)
When a “stop current” continues for 2.5 seconds after rushing on the stop zone, the compressor
operation stops.
If a “drooping current” is continues for 1.0 second after rushing on the drooping zone, the
frequency will be 2 Hz drooping.
Repeating the above drooping continues until the current rushes on the drooping zone without change.
In the unchanged zone, the frequency limit will remain.
In the return / reset zone, the frequency limit will be cancelled.
Limitation of current drooping and stop value according to the outdoor air temperature
1. In case the operation mode is cooling
Š The current droops when outdoor air temperature becomes higher than a certain level
(model by model).
2. In case the operation mode is heating (only for heat pump model)
Š The current droops when outdoor air temperature becomes higher than a certain level
(model by model).
82
Function and Control
SiEBE12-625
3.6
Control Specification
Freeze-up Protection Control
Outline
During cooling operation, the signals being sent from the indoor unit allow the operating
frequency limitation and then prevent freezing of the indoor heat exchanger. (The signal from
the indoor unit must be divided into the zones as the followings.
Detail
Conditions for Start Controlling
Judge the controlling start with the indoor heat exchanger temperature after 2 sec from
operation start and after 30 sec from changing number of operation room.
Control in Each Zone
Heat exchanger
thermistor temperature
Return from stop
13°C
Reset zone
7°C
Up zone
5°C
Keep zone
3°C
0°C
Drooping zone
Stop zone
(R4561)
3.7
Heating Peak-cut Control
Outline
Heat Pump Only
During heating operation, the signals being sent form the indoor unit allow the operating
frequency limitation and prevent abnormal high pressure. (The signal from the indoor unit must
be divided as follows.)
Detail
Conditions for Start Controlling
Judge the controlling start with the indoor heat exchanger temperature after 2 min from
operation start and after A sec from changing number of operation room.
Control in Each Zone
The maximum value of heat exchange intermediate temperature of each indoor unit controls the
following (excluding stopped rooms).
When increase
When decrease
Stop zone
A
30
2
Drooping zone
Keep zone
Up zone
Heat exchanger
thermistor
temperature
Function and Control
Reset zone
83
Control Specification
3.8
SiEBE12-625
Fan Control
Outline
Fan control is carried out with following functions.
1. Fan ON control for electric component cooling fan
2. Fan control when defrosting
3. Fan OFF delay when stopped
4. ON/OFF control when cooling operation
5. Fan control when the number of heating rooms decreases
6. Fan control when forced operation
7. Fan control in indoor / outdoor silent operation
8. Fan control for pressure difference upkeep
Detail
Fan OFF Control when Stopped
Š Fan OFF delay for 60 seconds must be made when the compressor is stopped.
Fan control when the number of heating room decreases (Only for Heat Pump Model)
When the outdoor air temperature is more than 10°C, the fan must be turned OFF for 30
seconds.
Tap Control in Indoor / Outdoor Unit Silent Operation
1. When Cooling Operation
When the outdoor air temperature is less than 37°C, the fan tap must be set to L.
2. When Heating Operation
When the outdoor air temperature is more than 4°C, the fan tap must be turned to L (only for
heat pump model).
3.9
Liquid Compression Protection Function 2
Outline
In order to obtain the dependability of the compressor, the compressor must be stopped
according to the conditions of the temperature of the outdoor air and outdoor heat exchanger.
Detail
Heat Pump Model
Š Operation stop depending on the outdoor air temperature
Compressor operation turns OFF under the conditions that the system is in cooling operation
and outdoor air temperature is below –10°C.
Cooling Only Model
Š Operation stops depending on the outdoor air temperature.
Compressor operation turns OFF under the condition that outdoor air temperature is below
–10°C.
84
Function and Control
SiEBE12-625
Control Specification
3.10 Defrost Control
Outline
Heat Pump Only
Defrosting is carried out by the cooling cycle (reverse cycle). The defrosting time or outdoor
heat exchanger temperature must be more than its fixed value when finishing.
Detail
Conditions for Starting Defrost
The starting conditions must be made with the outdoor air temperature and heat exchanger
temperature. Under the conditions that the system is in heating operation, 6 minutes after the
compressor is started and more than 47 minutes of accumulated time pass since the start of the
operation or ending the defrosting.
Conditions for Canceling Defrost
The target heat exchanger temperature as the canceling condition is selected in the range of
4°C<Te<12°C according to the air temperature as the following formula.
The target heat exchanger temperature=–(45/65)×(ambient temperature)+14
The defrost operation surely operates in 120 seconds after the start. (A→B)
After then the defrost operation stops at the following conditions.
1. When the heat exchanger temperature reaches the target heat exchanger temperature.
(B→C)
2. When 650 seconds have passed after the start even if the heat exchanger temperature does
not reaches the target heat exchanger temperature. (C)
A
C
B
2YC45 : 52 Hz
2YC45 : 52Hz
PI control
43 minutes
0Hz
120 seconds
650 seconds
60 seconds
6 minutes
1
Preparation 0
signal
Start
30 seconds 7 minutes
Completion
0 seconds
1
Defrosting
0
signal
Compressor ON
OFF
4-way valve ON
OFF
5 seconds
Fan ON
OFF
5 seconds
Solenoid ON
valve
OFF
Operating room
Motorized valve
opening
Operating
stopped room
Valve motorized
opening
Function and Control
450pps 450pps
450pps
Initial opening
Initial opening
140pps
85
Control Specification
SiEBE12-625
3.11 Low Hz High Pressure Limit
Outline
Heat Pump Only
Set the upper limit of high pressure in a low Hz zone. Set the upper limit of the indoor heat
exchanger temperature by its operating frequency of Hz. Separate into three zones, reset zone,
unchanged zone and drooping zone and the frequency control must be carried out in such
zones.
Detail
Separate into Zones
60°C
Highest heat
exchanger
Reset zone
temperature
among the
operating rooms
Note:
Drooping zone
59°C
Unchanged
zone 56°C
Drooping: The system stops 2 minutes after staying in the drooping zone.
3.12 Electronic Expansion Valve Control
Outline
The following items are included in the electronic expansion valve control.
Electronic expansion valve is fully closed
1. Electronic expansion valve is fully closed when turning on the power.
2. Pressure equalizing control
Room Distribution Control
1. Gas pipe isothermal control (distribution control in cooling)
2. SC control (only for heat pump model, distribution control in heating)
Open Control
1. Electronic expansion valve control when starting operation
2. Control when frequency changed
3. Control for defrosting (only for heat pump model)
4. Oil recover control
5. Control when a discharge pipe temperature is abnormally high
6. Control when the discharge pipe thermistor is disconnected
7. Control for indoor unit freeze-up protection
Feedback Control
1. Discharge pipe temperature control
Distribution control for each room
1. Liquid pipe temperature control (with all ports connected and all rooms being airconditioned)
2. Liquid pipe temperature control for stopped rooms
3. Dew prevention function for indoor rotor
86
Function and Control
SiEBE12-625
Control Specification
Detail
Gas pipe isothermal control
SC control
(only for heat pump model)
Control when frequency changed
Control for abnormally high discharge
pipe temperature
Oil recovery control
Indoor freeze-up protection control
Liquid pipe temperature control
Fully closed when power is turned ON
×
×
×
×
×
×
×
×
×
Open control when starting
×
×
×
×
×
×
(Control of target discharge pipe temperature)
×
×
×
×
Control when the operating room is changed
×
×
×
×
×
(Control of target discharge pipe temperature)
×
×
×
Pressure equalizing control
×
×
×
×
×
×
×
×
×
Open control when starting
×
×
×
×
×
×
×
×
×
All
rooms
(Control of target discharge pipe temperature)
×
×
×
Control when the operating room is changed
×
×
×
×
×
×
×
×
All
rooms
(Control of target discharge pipe temperature)
×
×
×
(Defrost control FD=1)
(only for heat pump model)
×
×
×
×
×
×
×
×
×
Pressure equalizing control
×
×
×
×
×
×
×
×
×
Open control when starting
×
×
×
×
×
×
×
×
×
×
×
Operation pattern
O : function
X : not function
When power is turned ON
Cooling, 1 room operation
Cooling, 2 rooms operation
to
Cooling, 4 rooms operation
Stop
Heating, 1 room operation
(only for heat
pump model)
Heating, 2 rooms operation
to
Heating, 4 rooms operation
(only for heat
pump model)
Stop
×
Stop
Heating operation
(only for heat
pump model)
Control of discharge pipe
thermistor disconnection
Liquid pipe temperature control for
stopped rooms
Dew prevention control for indoor rotor
The followings are the examples of control which function in each mode by the electronic
expansion valve control.
×
Continue
×
Pressure equalizing control
×
All
rooms
×
×
×
×
×
×
×
×
×
×
All
All
rooms rooms
×
×
All
All
rooms rooms
All
All
rooms rooms
×
×
×
(R3056)
Function and Control
87
Control Specification
SiEBE12-625
3.12.1 Fully Closing with Power ON
Initialize the electronic expansion valve when turning on the power, set the opening position and
develop pressure equalizing.
3.12.2 Pressure Equalization Control
When the compressor is stopped, open and close the electronic expansion valve and develop
pressure equalization.
3.12.3 Opening Limit
Outline
Limit a maximum and minimum opening of the electronic expansion valve in the operating room.
Detail
Š A maximum electronic expansion valve opening in the operating room: 450 pulses
Š A minimum electronic expansion valve opening in the operating room: 75 pulses
The electronic expansion valve is fully closed in the room where cooling is stopped and is
opened with fixed opening during defrosting.
3.12.4 Gas Pipe Isothermal Control During Cooling
When the units are operating in multiple rooms, detect the gas piping temperature and correct
the electronic expansion valve opening so that the temperature of the gas pipe in each room
becomes identical.
Š When the gas pipe temperature > the average gas pipe temperature,
→ open the electronic expansion valve in that room
Š When the gas pipe temperature < the average gas pipe temperature,
→ close the electronic expansion valve in that room
3.12.5 SC Control
Outline
Heat Pump Only
Detect the temperature of liquid pipe and heat exchanger of the rooms and compensate the
electronic expansion valve opening so that the SC of each room becomes the target SC.
Š When the actual SC is > target SC, open the electronic expansion valve of the room.
Š When the actual SC is < target SC, close the electronic expansion valve of the room.
Detail
Start Functioning Conditions
After finishing the open control (660 seconds after the beginning of the operation), control all the
electronic expansion valve in the operating room.
Determine Electronic Expansion Valve Opening
Adjust the electronic expansion valve so that the temperature difference between the maximum
heat exchanger temperature of connected room and the temperature of liquid pipe thermistor
becomes constant.
3.12.6 Starting Operation Control / Changing Operation Room
Control the electronic expansion valve opening when the system is starting or the operating
room is changed, and prevent the system to be super heated or moistened.
88
Function and Control
SiEBE12-625
Control Specification
3.12.7 Disconnection of the Discharge Pipe Thermistor
Outline
Detect a disconnected discharge pipe thermistor by comparing the discharge pipe temperature
with the condensation temperature. If any is disconnected, open the electronic expansion valve
according to the outdoor air temperature and the operating frequency and operate for a
specified time, and then stop.
After 3 minutes of waiting, restart the unit and check if any is disconnected. If any is
disconnected stop the system after operating for a specified time. If the disconnection is
detected 4 times in succession, then the system will be down.
Detail
Detect Disconnection
If a 630-second timer for open control becomes over, and a 9-minute timer for the compressor
operation continuation is not counting time, the following adjustment must be made.
1. When the operation mode is cooling
When the discharge pipe temperature is lower than the outdoor heat exchanger
temperature, the discharge pipe thermistor disconnection must be ascertained.
2. When the operation mode is heating (only for heat pump model)
When the discharge pipe temperature is lower than the max temperature of operating room
heat exchanger, the discharge pipe thermistor disconnection must be ascertained.
Adjustment when the thermistor is disconnected
When compressor stop repeats specified time, the system should be down.
3.12.8 Control when frequency is changed
When the target pipe temperature control is active, if the target frequency is changed for a
specified value in a certain time period, cancel the target discharge pipe temperature control
and change the opening of the target electronic expansion valve according to the shift.
3.12.9 High Temperature of the Discharge Pipe
When the compressor is operating, if the discharge pipe temperature exceeds a certain value,
open the electronic expansion valve and remove the refrigerant to the low pressure side and
lower discharge temperature.
3.12.10 Oil Recovery Function
Outline
The electronic expansion valve opening in the cooling stopped room must be set as to open for
a certain time at a specified interval so that the oil in the cooling stopped room may not be
accumulated.
Detail
During cooling operation, every 1 hour continuous operation, the electronic expansion valves in
the operation stopped room must be opened by 80 pulses for specified time.
3.12.11 Target Discharge Pipe Temperature Control
Obtain the target discharge pipe temperature from the indoor and outdoor heat exchange
temperature, and adjust the electronic expansion valve opening so that the actual discharge
pipe temperature become close to that temperature. (Indirect SH control using the discharge
pipe temperature)
SC
SH
Set the target discharge pipe
temperature as to become an aiming
SH.
Regard that the inclination cannot be
changed due to the operating
condition.
Determine a correction value of the electronic expansion valve compensation and drive it
according to the deflection of the target discharge temperature and actual discharge
temperature, and the discharge temperature variation by the 20 sec.
Function and Control
89
Control Specification
SiEBE12-625
3.13 Malfunctions
3.13.1 Sensor Malfunction Detection
Sensor malfunction may occur either in the thermistor or current transformer (CT) system.
Relating to Thermistor Malfunction
1. Outdoor heat exchanger thermistor
2. Discharge pipe thermistor
3. Fin thermistor
4. Gas pipe thermistor
5. Outdoor air temperature thermistor
6. Liquid pipe thermistor
Relating to CT Malfunction
When the output frequency is more than 55 Hz and the input current is less than 1.25A, carry
out abnormal adjustment.
3.13.2 Detection of Overload and Over Current
Outline
In order to protect the inverter, detect an excessive output current, and for protecting
compressor, monitor the OL operation.
Detail
Š If the OL (compressor head) temperature exceeds 130°C (for the 2YC32) (120°C for 52
class) or 130°C (for the 2YC45), the compressor gets interrupted.
Š If the inverter current exceeds 30 A, the compressor gets interrupted too.
3.13.3 Insufficient Gas Control
Outline
If a power consumption is below the specified value in which the frequency is higher than the
specified frequency, it must be regarded as gas insufficient.
In addition to such conventional function, if the discharge temperature is higher than the target
discharge pipe temperature, and more than the specified temperature, and the electronic
expansion valve is fully open (450 pulses) more than the specified time, it is considered as an
insufficient gas.
Power consumption
Insufficient gas zone
55 Hz
Frequency
(R2834)
With the conventional function, a power consumption is weak comparing with that in the normal
operation when gas is insufficient, and gas insufficiency is detected by checking a power
consumption.
Gas insufficient
zone
(R1391)
When operating with insufficient gas, although the rise of discharge pipe temperature is great
and the electronic expansion valve is open, it is presumed as an insufficient gas if the discharge
pipe temperature is higher than the target discharge pipe temperature.
90
Function and Control
SiEBE12-625
Detail
Control Specification
Judgment by Input Current
When an output frequency is exceeds 55 Hz and the input current is less than specified value,
the adjustment is made for insufficient gas.
Judgment by Discharge Pipe Temperature
When discharge pipe temperature is 20°C higher than target value and the electronic expansion
value opening is 450 plus (max.), the adjustment is made for insufficient gas.
3.13.4 Preventing Indoor Freezing
During cooling, if the heat exchanger temperature in the operation stopped room becomes
below the specified temperature for the specified time, open the electronic expansion valve in
the operation stopped room as specified, and carry out the fully closed operation. After this, if
freezing abnormality occurs more than specified time, the system shall be down as the system
abnormality.
3.14 Forced Operation Mode
Outline
Forced operating mode includes functions such as; forced cooling, forced heating, incorrect
wiring, incorrect piping check.
Operating mode must be selected by operating the forced operation switch.
Detail
Forced Cooling, Forced Heating (Only for Heat Pump Model)
Item
Forced operation
allowing conditions
Forced Cooling
1) The indoor unit is not abnormal, but
the indoor unit which is not in the
freezing prohibiting zone is present in
more than 1 room.
2) The outdoor unit is not abnormal
and not in the 3-minute stand-by
mode.
3) The operating mode of the outdoor
unit is the stop mode.
4) The slide selection switch of the
forced operation is the cooling mode.
The forced operation is allowed when
the above “and” conditions are met.
Starting / adjustment If the forced operation switch is
pressed as the above conditions are
met.
1) Determine
All rooms
operating room
2) Command
frequency
3) Electronic
expansion valve
opening
4) Outdoor unit
adjustment
5) Indoor unit
adjustment
End
Others
Function and Control
Š 2YC45: 42 Hz
It depends on the capacity of the
operating indoor unit.
Forced Heating
1) The indoor unit is not abnormal.
The indoor unit which is not in the
peak-cut prohibited zone is present in
more than 1 room.
←
←
4) The slide selection switch of the
forced operation is the heating mode.
The forced operation is allowed when
the above “and” conditions are met.
←
One of the available units runs.
Priority is given to the youngest
number’s room in alphabetical order.
(A > B > C > D)
Š 2YC45: 37 Hz
(Outdoor air temp:0°C)
←
Compressor is in operation.
←
The command of forced operation is
transmitted to the indoor unit.
1) When the forced operation switch is
pressed again.
2) The operation is to end
automatically after 30 min.
The protect functions are prior to all
others in the forced operation.
←
←
←
←
91
Control Specification
SiEBE12-625
3.15 Wiring-Error Check
Outline
The convenient Wiring Error Check function is designed for the microcomputer to correct wiring
errors itself.
If local wiring is unclear in the case of buried piping, for example, just press the wiring error
check switch that is behind the right-hand panel of the outdoor unit. Even if the connections for
Room A and Room B are confused, the system may run without a hassle. Note that this check
function does not work in the following cases.
Š For about 30 seconds after the power is turned on (during initial setup).
Š For 3-minute standby period after the compressor has stopped.
Š When the outdoor air temperature is below 5°C.
Š If the indoor unit is in trouble (also in case of all-room transmission failure).
When the piping and wiring are perfect, there is no need to use this function.
Operation
1. Remove the 5 screws from the service panel (right side panel) and detach the panel.
2. Press the wiring error check switch on the service monitor PCB, and the wiring error check
function is activated.
3. In about 10-15 minutes, the checking will end automatically.
4. When the checking is over, the service monitor LED indicators start flashing.
LED
Status
1
2
3
4
All flashing at once
Flashing one after another
Judgment
Self-correction impossible
Self-correction complete
Self-correction complete…The LED indicators 1 ~ 4 flash one after another.
Self-correction impossible…The LED indicators flash all at the same time.
Š Transmission failure occurs at any of the indoor units.
Š The indoor unit heat exchanger thermistor is disconnected.
Š An indoor unit is in trouble (if a trouble occurs during the wiring error checking).
Emergency stop…Any of the LED indicators 1 ~ 4 stays on.
Note:
1. It takes about 10-15 minutes (after pressing the wiring error check switch) to complete the
checking. (Wrong wiring between the upper and lower units cannot be self-corrected.)
2. Wrongly connected liquid and gas pipes cannot be self-corrected either. Be sure to make the
liquid pipe and the gas pipe in pairs.
3. To forced-terminate the wiring error check procedure halfway, press the wiring error check
switch again.
In this case, the microcomputer's memory gets back to its initial status (Room A wiring →
Port A piping, Room B wiring → Port B piping).
4. In replacing the outdoor unit PCB, be sure to use this function.
5. Make the power slide setting after doing the wiring error checking. (Otherwise, if the wiring is
reversed, the air-conditioners being connected are set up in the reverse way.)
Basic Knowledge
Š This function works in this way. Refrigerant is let flow from Port A and on. The temperatures
of the indoor unit heat exchanger thermistors are detected one by one to check up the
matching between the pipes and wiring.
Š With this function on, freezing (crackling) noise may be heard from the indoor unit. This is
not a problem. (This is because the heat exchange temperature is made to drop below 0°C
in order to increase the detection accuracy.)
Š The indoor fan is made to turn on and off at the same time.
92
Function and Control
SiEBE12-625
Control Specification
Checking the
current setting
data on the
microcomputer
memory
Those data can be checked by looking at the service monitor LED indicators, when the wiring
error checking is over, during forced operation, at the stop of the system.
The LED indicators stop flashing when the forced operation is over.
LED1…Room A wiring, LED2…Room B wiring
1st flashing LED…Port A piping, 2nd flashing LED…Port B piping
The first stay-on LED means the room that is connected with Port A. The next stay-on LED
means the one connected with Port B.
Example
Let's suppose the LED indicators are flashing as follows.
L A 1 2 3 4
E
D Green Red
L A 1 2 3 4
E
L A 1 2 3 4
D Green Red
E
D Green Red
The above means that Port A is connected with Port B and Port B with Room A (or selfcorrected this way.)
A
Wiring
B
Piping
A
B
Wiring
Piping
Function and Control
93
Control Specification
SiEBE12-625
3.16 Additional Function
3.16.1 Connection Pipe Condensation Preventing Function
This control is intended to adjust the electronic expansion valve opening so that the outdoor unit
gas pipe temperature (GDN) be kept below 8°C.
3.16.2 Priority Room Setting
Electronic expansion valves are controlled to provide the unit designated as the priority room
with the capacity of other room units.
(Distribution of capacity: Priority room unit --- ΔD Max., other room units --- ΔD -α)
Š Setting method
Turn off the circuit breaker before changing the setting.
Only one room can be set as the priority room.
Š Control start conditions
Priority room setting is made.
AND
“Powerful” signal from the priority room unit is received.
Note:
The operation mode of the priority room unit has precedence.
Š Cancellation of control
The control function is canceled when the “Powerful” operation mode is switched off or 20
minutes elapse after “Powerful Operation” started.
A
room
A
room
B
room
Living
room
C
room
B
room
Living
room
C
room
Normal
operation
When Inverter
powerful-operation
is selected in the
priority room
The prioritised room will be heated/cooled much more quickly
(R1396)
3.16.3 POWERFUL Operation Mode
Compressor operating frequency is increased to PI Max. (Max. Hz of operating room unit ΣS)
and outdoor unit airflow rate is increased.
3.16.4 Voltage Detection Function
Power supply voltage is detected each time equipment operation starts.
94
Function and Control
SiEBE12-625
Control Specification
3.16.5 Cooling / Heating Mode Lock
Use the S15 connector to set the unit to only cool or heat.
Setting to only heat (H): Short-circuit pins 1 and 3 of the connector <S15>.
Setting to only cool (C): short-circuit pins 3 and 5 of the connector <S15>.
The following specifications apply to the connector housing and pins.
JST products Housing: VHR-5N
Pin: SVH-21T-1, 1
Note that forced operation is also possible in COOL / HEAT mode.
COOL mode (C)
HEAT mode (H)
5<C>3<H>1
Function and Control
(R1397)
95
Control Specification
96
SiEBE12-625
Function and Control
SiEBE12-625
Part 5
System Configuration
1. System Configuration............................................................................98
1.1 Operation Instructions ............................................................................98
2. Instruction..............................................................................................99
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
System Configuration
Manual Contents and Reference Page ..................................................99
Safety Precautions ...............................................................................100
Names of Parts.....................................................................................102
Preparation Before Operation ..............................................................126
AUTO • DRY • COOL • HEAT • FAN Operation ...................................129
Adjusting the Air Flow Direction ...........................................................131
POWERFUL Operation ........................................................................143
OUTDOOR UNIT SILENT Operation ...................................................144
ECONO Operation ...............................................................................145
HOME LEAVE Operation .....................................................................146
INTELLIGENT EYE Operation .............................................................148
TIMER Operation .................................................................................156
Note for Multi System ...........................................................................158
Care and Cleaning ...............................................................................160
Troubleshooting ...................................................................................185
97
System Configuration
SiEBE12-625
1. System Configuration
1.1
Operation Instructions
After the installation and test operation of the room air conditioner have been completed, it should be
operated and handled as described below. Every user would like to know the correct method of
operation of the room air conditioner, to check if it is capable of cooling (or heating) well, and to know a
clever method of using it.
In order to meet this expectation of the users, giving sufficient explanations taking enough time can be
said to reduce about 80% of the requests for servicing. However good the installation work is and
however good the functions are, the customer may blame either the room air conditioner or its
installation work because of improper handling. The installation work and handing over of the unit can
only be considered to have been completed when its handling has been explained to the user without
using technical terms but giving full knowledge of the equipment.
98
List of Functions
SiEBE12-625
Instruction
2. Instruction
2.1
Manual Contents and Reference Page
Wall Mounted Type
Model Series
FTK(X)S20/25/35/50D
FTK(X)S20/25/35C
FTK(X)S50/60/71E
FTK(X)S71B
Safety Precautions
100
100
100
100
Names of Parts
102
105
108
111
Preparation before Operation H
126
126
126
126
AUTO, DRY, COOL, HEAT, FAN
Operation H
129
129
129
129
Adjusting the Air Flow Direction
131
133
135
135
Read before Operation
Operation
POWERFUL Operation H
143
143
143
143
OUTDOOR UNIT SILENT Operation
H
144
144
144
144
ECONO Operation
145
—
—
—
—
146
146
146
152
HOME LEAVE Operation H
INTELLIGENT EYE Operation
148
150
152
TIMER Operation H
156
156
156
156
Note for Multi System
158
158
158
158
160
163
166
169
Care
Care and Cleaning
Trouble Shooting
Trouble Shooting
Drawing No.
185
185
185
185
3P142629-1C
3P170835-4
3P119293-2L
3P170835-1A
3P098586-1J
Wall Mounted
Type
Model Series
Duct Connected Type
Floor/Ceiling
Suspended Dual
Type
Floor Standing
Type
FTXG25/35E
CTXG50E
FDK(X)S25/35C
FDK(X)S50/60C
FDK(X)S25/35E
Safety Precautions
100
100
100
100
100
Names of Parts
114
117
117
120
123
Preparation before Operation H
126
126
126
126
126
AUTO, DRY, COOL, HEAT, FAN
Operation H
129
129
129
129
129
Adjusting the Air Flow Direction
137
—
—
139
141
FLK(X)S25/35/50/60B FVK(X)S25/35/50B
Read before Operation
Operation
POWERFUL Operation H
143
143
143
143
143
OUTDOOR UNIT SILENT Operation
H
144
144
144
144
144
ECONO Operation
—
—
—
—
—
HOME LEAVE Operation H
—
146
146
146
146
INTELLIGENT EYE Operation
154
—
—
—
—
TIMER Operation H
156
156
156
156
156
Note for Multi System
158
158
158
158
158
172
175
177
179
182
Care
Care and Cleaning
Trouble Shooting
Trouble Shooting
Drawing No.
185
185
185
185
185
3P166453-1B
3P131999-2L
3P131999-3K
3P098587-2N
3P098587-1N
H : Illustrations are for wall mounted type FTXS20-50D as representative.
List of Functions
99
Instruction
2.2
SiEBE12-625
Safety Precautions
•
•
•
•
Keep this manual where the operator can easily find them.
Read this manual attentively before starting up the unit.
For safety reason the operator must read the following cautions carefully.
This manual classifies precautions into WARNINGS and CAUTION. Be sure to follow all
precautions below: they are all important for ensuring safety.
WARNING
CAUTION
If you do not follow these instructions exactly, the unit may
cause property damage, personal injury or loss of life.
Never do.
Be sure to follow the instructions.
Be sure to earth the air conditioner.
Never cause the air conditioner (including the
remote control) to get wet.
Never touch the air conditioner (including the
remote control) with a wet hand.
•
•
•
•
•
•
•
•
If you do not follow these instructions exactly, the unit may
cause minor or moderate property damage or personal injury.
WARNING
In order to avoid fire, explosion or injury, do not operate the unit when harmful, among
which flammable or corrosive gases, are detected near the unit.
It is not good for health to expose your body to the air flow for a long time.
Do not put a finger, a rod or other objects into the air outlet or inlet. As the fan is rotating at a high
speed, it will cause injury.
Do not attempt to repair, relocate, modify or reinstall the air conditioner by yourself. Incorrect work
will cause electric shocks, fire etc.
For repairs and reinstallation, consult your Daikin dealer for advice and information.
The refrigerant used in the air conditioner is safe. Although leaks should not occur, if for
some reason any refrigerant happens to leak into the room, make sure it does not come
in contact with any flame as of gas heaters, kerosene heaters or gas range.
If the air conditioner is not cooling (heating) properly, the refrigerant may be leaking, so call your
dealer. When carrying out repairs accompanying adding refrigerant, check the content of the
repairs with our service staff.
Do not attempt to install the air conditioner by your self. Incorrect work will result in water leakage,
electric shocks or fire. For installation, consult the dealer or a qualified technician.
In order to avoid electric shock, fire or injury, if you detect any abnormally such as smell of fire,
stop the operation and turn off the breaker. And call your dealer for instructions.
CAUTION
•
•
•
•
•
•
•
•
•
•
•
100
The air conditioner must be earthed. Incomplete earthing may result in electric shocks.
Do not connect the earth line to a gas pipe, water pipe, lightning rod, or a telephone earth
line.
In order to avoid any quality deterioration, do not use the unit for cooling precision
instruments, food, plants, animals or works of art.
Never expose little children, plants or animals directly to the air flow.
Do not place appliances which produce open fire in places exposed to the air flow from the unit or
under the indoor unit. It may cause incomplete combustion or deformation of the unit due to the
heat.
Do not block air inlets nor outlets. Impaired air flow may result in insufficient performance or
trouble.
Do not stand or sit on the outdoor unit. Do not place any object on the unit to avoid injury, do not
remove the fan guard.
Do not place anything under the indoor or outdoor unit that must be kept away from moisture. In
certain conditions, moisture in the air may condense and drip.
After a long use, check the unit stand and fittings for damage.
Do not touch the air inlet and aluminum fins of outdoor unit. It may cause injury.
The appliance is not intended for use by young children or infirm persons without supervision.
Young children should be supervised to ensure that they do not play with the appliance.
List of Functions
SiEBE12-625
Instruction
•
•
•
•
•
•
•
•
•
To avoid oxygen deficiency, ventilate the room sufficiently if equipment with burner is
used together with the air conditioner.
Before cleaning, be sure to stop the operation, turn the breaker off or pull out the supply
cord.
Do not connect the air conditioner to a power supply different from the one as specified. It may
cause trouble or fire.
Depending on the environment, an earth leakage breaker must be installed. Lack of an earth
leakage breaker may result in electric shocks.
Arrange the drain hose to ensure smooth drainage. Incomplete draining may cause wetting of the
building, furniture etc.
Do not place objects in direct proximity of the outdoor unit and do not let leaves and other debris
accumulate around the unit.
Leaves are a hotbed for small animals which can enter the unit. Once in the unit, such animals
can cause malfunctions, smoke or fire when making contact with electrical parts.
Do not operate the air conditioner with wet hands.
Do not wash the indoor unit with excessive water, only use a slightly wet cloth.
Do not place things such as vessels containing water or anything else on top of the unit.
Water may penetrate into the unit and degrade electrical insulations, resulting in an
electric shock.
Installation site
„ To install the air conditioner in the following types of environments, consult the dealer.
• Places with an oily ambient or where steam or soot occurs.
• Salty environment such as coastal areas.
• Places where sulfide gas occurs such as hot springs.
• Places where snow may block the outdoor unit.
The drain from the outdoor unit must be discharged to a place of good drainage.
Consider nuisance to your neighbours from noises
„ For installation, choose a place as described below.
• A place solid enough to bear the weight of the unit which does not amplify the operation noise or
vibration.
• A place from where the air discharged from the outdoor unit or the operation noise will not
annoy your neighbours.
Electrical work
•
For power supply, be sure to use a separate power circuit dedicated to the air conditioner.
System relocation
•
List of Functions
Relocating the air conditioner requires specialized knowledge and skills. Please consult the
dealer if relocation is necessary for moving or remodeling
101
Instruction
2.3
SiEBE12-625
Names of Parts
FTK(X)S 20/25/35/50 D
„ Indoor Unit
1
2
3
4
5
7
11
10
9
6
8
16
14
13
15
ON/OFF
102
12
List of Functions
SiEBE12-625
Instruction
„ Outdoor Unit
17
22
19
20
18
21
„ Indoor Unit
1. Air filter
2. Titanium Apatite Photocatalytic
Air-Purifying Filter:
• These filters are attached to the inside of
the air filters.
3. Air inlet
4. Front panel
5. Panel tab
6. Room temperature sensor:
• It senses the air temperature around the
unit.
7. INTELLIGENT EYE sensor:
• It detects the movements of people and
automatically switches between normal
operation and energy saving operation.
8. Display
9. Air outlet
10. Flaps (horizontal blades)
11. Louvers (vertical blades):
• The louvers are inside of the air outlet.
12. Indoor Unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refers to the following
table.:
Mode
Temperature
setting
Air flow
rate
F(C)TKS
COOL
22°C
AUTO
F(C)TXE
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing.
13. Operation lamp (green)
14. TIMER lamp (Yellow)
15. INTELLIGENT EYE lamp (green)
16. Signal receiver:
• It receives signals from the remote control.
• When the unit receives a signal, you will
hear a short beep.
• Operation start ..............beep-beep
• Settings changed..........beep
• Operation stop ..............beeeeep
„ Outdoor Unit
21. Earth terminal:
• It is inside of this cover.
22. Outside air temperature sensor:
• It senses the ambient temperature around
the unit.
Appearance of the outdoor unit may differ from some models.
17. Air inlet: (Back and side)
18. Air outlet
19. Refrigerant piping and inter-unit cable
20. Drain hose
List of Functions
103
Instruction
SiEBE12-625
„ Remote control
1
2
5
ECONO
ON/OFF
3
POWERFUL
TEMP
6
4
7
8
13
MODE
SWING
FAN
SILENT COMFORT SENSOR
ON
CANCEL
9
10
12
11
16
OFF
TIMER
15
18
17
14
<ARC433A50, 43>
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. ECONO button:
ECONO operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
104
8. SILENT button: OUTDOOR UNIT SILENT
operation
• Only works for multi-connection
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button
• Adjusting the Air Flow direction.
11. COMFORT AIRFLOW button:
COMFORT AIRFLOW operation
12. SENSOR button: INTELLIGENT EYE
operation
13. ON TIMER button
14. OFF TIMER button
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button
18. RESET button:
• Restart the unit if it freezes.
• Use a thin object to push.
List of Functions
SiEBE12-625
Instruction
FTK(X)S 20/25/35 C
„ Indoor Unit
ON
OFF
List of Functions
105
Instruction
SiEBE12-625
„ Oudoor Unit
„ Indoor Unit
1. Air filter
2. Air purifying filter with photocatalytic
deodorizing function:
• These filters are attached to the inside of
the air filters.
3. Air inlet
4. Front panel
5. Panel tab
6. Room temperature sensor:
• It senses the air temperature around the
unit.
7. INTELLIGENT EYE sensor:
• It detects the movements of people and
automatically switches between normal
operation and energy saving operation.
8. Display
9. Air outlet
10. Flaps (horizontal blade)
11. Louvers (vertical blades):
• The louvers are inside of the air outlet.
12. indoor Unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refers to the following
table.
Mode
Temperature
setting
Air flow
rate
FTKS
COOL
22°C
AUTO
FTXS
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing.
13. Operation lamp (green):
14. TIMER lamp (yellow)
15. HOME LEAVE lamp (red)
16. Signal receiver:
• It receives signals from the remote control.
• When the unit receives a signal, you will
hear a short beep.
• Operation start ..............beep-beep
• Settings changed..........beep
• Operation stop ..............beeeeep
„ Outdoor Unit
21. Earth terminal:
• It is inside of this cover.
22. Outside air temperature sensor: (Back side)
• It senses the ambient temperature around
the unit
Appearance of the outdoor unit may differ from some models.
17. Air inlet: (Back and side)
18. Air outlet
19. Refrigerant piping and inter-unit cable
20. Drain hose
106
List of Functions
SiEBE12-625
Instruction
„ Remote control
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
HOME LEAVE operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
List of Functions
•
It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
8. SILENT button: OUTDOOR UNIT SILENT
operation
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button
11. SENSOR button:
INTELLIGENT EYE operation
12. ON TIMER button
13. OFF TIMER button
14. TIMER Setting button:
• It changes the time setting.
15. TIMER CANCEL button:
• It cancels the timer setting.
16. CLOCK button
107
Instruction
SiEBE12-625
CDK(X)S 50/60/71 E
„ Indoor Unit
4
5
3
2
9
1
10
6
8
7
11
12
14
13
„ Main unit control panel
16
15
108
List of Functions
SiEBE12-625
Instruction
„ Outdoor Unit
17
19
20
21
18
„ Indoor Unit
1. Air filter
2. Titanium Apatite Photocatalytic
Air-Purifying Filter
• These filters are attached to the inside of
the air filters
3. Air inlet
4. Front panel
5. Panel tab:
6. INTELLIGENT EYE sensor:
• It detects the movements of people and
automatically switches between normal
operation and energy saving operation.
7. Display
8. Air outlet
9. Flap (horizontal blade)
10. Louvers (vertical blades)
• The Louvers are inside of the air outlet.
11. Operation Lamp (green)
12. TIMER lamp (yellow)
13. HOME LEAVE lamp (red):
• Lights up when you use HOME LEAVE
Operation
14. Indoor Unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refer to the following
table.
Mode
Temperature
setting
Air flow
rate
FTKS
COOL
22°C
AUTO
FTXS
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing.
15. Room temperature sensor:
• It senses the air temperature around the
unit.
16. Signal receiver:
• It receives signals from the remote
controller.
• When the unit receives a signal, you will
hear a short beep
• Operation start ...........beep-beep
• Settings changed .......beep
• Operartion stop ..........beeeeep
„ Outdoor Unit
17. Air inlet: (Back and side)
20. Drain hose
18. Air outlet
21. Earth terminal
• It is inside of this cover.
19. Refrigerant piping and inter-unit cable
Appearance of the outdoor unit may differ from some models.
List of Functions
109
Instruction
SiEBE12-625
„ Remote control
1
2
5
3
6
4
9
11
7
8
12
10
16
13
17
15
14
< ARC433A21, A22 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
HOME LEAVE operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature of time setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
110
8. SILENT button: for OUTDOOR UNIT SILENT
operation
9. FAN setting button:
• It selects the air flow rate setting.
10. SENSOR button: INTELLIGENT EYE
operation
11. SWING button:
• Flap (Horizontal blade)
12. SWING button:
• Louver (Vertical blades)
13. ON TIMER button
14. OFF TIMER button
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button
List of Functions
SiEBE12-625
Instruction
FLK(X)S 71 B
„ Indoor Unit
This illustration shows a 50-class unit
4
2
9
10
1
5
3
15
8
6
7
11
12
14
13
„ Main unit control panel
17
16
List of Functions
111
Instruction
SiEBE12-625
„ Oudoor Unit
18
20
21
22
19
„ Indoor Unit
1. Air filter
2. Air purifying filter with photocatalytic
deodorizing function:
• These filters are attached to the inside of
the air filters
3. Air inlet
4. Front grille
5. Grille tab
6. INTELLIGENT EYE sensor:
• It detects the movements of people and
automatically switches between normal
operation and energy saving operation.
7. Display
8. Air outlet
9. Flap (horizontal blade)
10. Louvers (vertical blades):
• The Louvers are inside of the air outlet.
11. Operation lamp (green)
12. TIMER lamp (yellow)
13. HOME LEAVE lamp (red):
Lights up when you use HOME LEAVE
Operation.
14. Indoor unit ON/OFF switch
• Push this switch once to start operation.
Push once again to stop it.:
• The operation mode refer to the following
table.
Mode
Temperature
setting
Air flow
rate
FTKS
COOL
22°C
AUTO
FTXS
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing.
15. Packaging materials: 50 class only
• If any packaging materials are included,
please remove before operating
16. Room temperature sensor:
• It senses the air temperature around the
unit.
17. Signal receiver:
• It receives signals from the remote control.
• When the unit receives a signal, you will
hear a short beep.
• Operation start ..............beep-beep
• Settings changed..........beep
• Operation stop ..............beeeeep
„ Outdoor Unit
21. Drain hose
18. Air inlet: (Back and side)
19. Air outlet
22. Earth terminal:
20. Refrigerant piping and inter-unit cable
• It is inside of this cover.
Appearance of the outdoor unit may differ from some models.
112
List of Functions
SiEBE12-625
Instruction
„ Remote control
1
ON
2
C
5
HOME LEAVE
ON/OFF
3
POWERFUL
TEMP
6
4
7
MODE
SILENT
FA N
SENSOR SWING
8
13
ON
9
11
10
12
CANCEL
16
OFF
TIMER
17
15
14
< ARC433A21, A22 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
for HOME LEAVE operation
4. POWERFUL button:
for POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature of time setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
List of Functions
8. SILENT button: for OUTDOOR UNIT
SILENT operation
9. FAN setting button:
• It selects the air flow rate setting.
10. SENSOR button: for INTELLIGENT EYE
operation
11. SWING button
• Flap (Horizontal blade)
12. SWING button
• Louver (Vertical blades)
13. ON TIMER button
14. OFF TIMER button
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button
113
Instruction
SiEBE12-625
FTXG 25/35 E, CTXG 50 E
„ Indoor Unit
1
2
3
4
5
6
7
8
9
(With the panel closed)
11
10
18
17
14
15
16
13
12
114
List of Functions
SiEBE12-625
Instruction
„ Outdoor Unit
„ Indoor Unit
1. Air filter
2. Titanium Apatite Photocatalytic
Air-Purifying Filter
• These filters are attached to the inside of
the air filters
3. Air inlet
4. Front panel
5. Supporting plate:
• The supporting plate is used to support the
front panel during maintenance.
6. Panel tab
7. Flap (horizontal blade)
8. Air outlet
9. Louvers (vertical blades)
• The louvers are inside of the air outlet.
10. Outlet vent panel
11. Display
12. Indoor unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
•
The operation mode refer to the following
table.
FTXS
Mode
Temperature
setting
Air flow
rate
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing
13. Room temperature sensor:
• It senses the air temperature around the unit
14. Operation Lamp (green)
15. TIMER lamp (yellow)
16. INTELLIGENT EYE lamp (green)
17. INTELLIGENT EYE sensor:
• It detects the movements of people and
automatically switches between normal
operation and energy saving operation.
18. Signal receiver:
• It receives signals from the remote controller.
• When the unit receives a signal, you will
hear a short beep
• Operation start ...........beep-beep
• Settings changed .......beep
• Operartion stop ..........beeeeep
„ Outdoor Unit
22. Drain hose
19. Air inlet: (Back and side)
20. Air outlet
23. Earth terminal
21. Refrigerant piping and inter-unit cable
• It is inside of this cover.
Appearance of the outdoor unit may differ from some models.
List of Functions
115
Instruction
SiEBE12-625
„ Remote control
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. SENSOR button:
INTELLIGENT EYE operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
116
8. SILENT button: OUTDOOR UNIT SILENT
operation
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button:
• Flap (Horizontal blade)
11. SWING button:
• Louver (Vertical blades)
12. COMFORT AIRFLOW mode button
13. ON TIMER button
14. OFF TIMER button
15. TIMER Setting button:
• It changes the time setting.
16. TIMER CANCEL button:
• It cancels the timer setting.
17. CLOCK button
List of Functions
SiEBE12-625
Instruction
FDK(X)S 25/35/50/60 C, FDK(X)S 25/35 E
„ Indoor Unit
1
5
2
4
3
6
8
7
9
10
List of Functions
117
Instruction
SiEBE12-625
„ Outdoor Unit
11
12
13
15
14
„ Indoor Unit
1. Air filter
2. Air outlet grille (field supply)
• Appearance of the Air outlet grille and Air
inlet grille may differ with some models.
3. Display, Control panel
4. Suction grille (option)
• Appearance of the sunction grille and Air
inlet grille may differ with some models.
5. Air inlet
6. Room temperature sensor
• It senses the air temperature around the
unit.
7. Operation lamp (green)
8. TIMER lamp (yellow)
9. HOME LEAVE lamp (red)
• Lights up when you use HOME LEAVE
operation.
10. Indoor Unit ON/OFF switch
• push this switch once to start operation.
Push once again to stop it..
• This switch is useful when the remote
controller is missing.
• The operation mode refers to the following table.
Mode
Temperature
setting
Air flow
rate
FDKS
COOL
22°C
AUTO
FDXS
AUTO
25°C
AUTO
„ Outdoor Unit
11. Air inlet: (Back and side)
14. Earth terminal
12. Refrigerant piping and inter-unit cable
• It is inside of this cover.
15. Air outlet
13. Drain hose
Appearance of the outdoor unit may differ from some models.
118
List of Functions
SiEBE12-625
Instruction
„ Remote control
1
ON
2
C
5
HOME LEAVE
ON/OFF
3
POWERFUL
TEMP
6
4
9
7
MODE
SILENT
FAN
8
10
ON
CANCEL
13
14
OFF
TIMER
12
11
< ARC433A7, A8 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
for HOME LEAVE operation
4. POWERFUL button:
for POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature of time setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
List of Functions
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
8. SILENT button: for OUTDOOR UNIT SILENT
operation
9. FAN setting button:
• It selects the air flow rate setting.
10. ON TIMER button
11. OFF TIMER button
12. TIMER Setting button:
• It changes the time setting.
13. TIMER CANCEL button:
• It cancels the timer setting.
14. CLOCK button
119
Instruction
SiEBE12-625
FLK(X)S 25/35/50/60 B
„ Indoor Unit
The indoor unit can be installed either to the ceiling or to a wall. The descriptions contained in this
manual show the case when installation is being carried out to the ceiling. (The methods of operation
used are the same when installing to a wall.)
„ Opening the front panel
How to open the front panel
CAUTION
•
120
Before opening the front panel, be sure to stop the operation and turn the breaker OFF.
List of Functions
SiEBE12-625
Instruction
„ Outdoor Unit
„ Indoor Unit
1. Louvers (vertical blades):
• The louvers are inside of the air outlet.
2. Air outlet
3. Flap (horizontal blade)
4. Panel tab
5. Air inlet
6. Display
7. Air filter
8. Photocatalytic deodorizing filter or
Air purifying filter:
• These filters are attached to the inside of
the air filters.
9. Front panel
10. Display
11. Operation Lamp (green)
12. TIMER lamp (yellow)
13. HOME LEAVE lamp (red)
• Lights up when you use HOME LEAVE
Operation
14. Indoor unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
• The operation mode refer to the following
table.
Mode
Temperature
setting
Air flow
rate
FLKS
COOL
22°C
AUTO
FLXS
AUTO
25°C
AUTO
•
Push the switch using an object with a
sharp tip, such as a pen.
• This switch is useful when the remote
controller is missing.
15. Signal receiver:
• It receives signals from the remote controller.
• When the unit receives a signal, you will
hear a short beep
• Operation start ...........beep-beep
• Settings changed .......beep
• Operartion stop ..........beeeeep
„ Outdoor Unit
19. Drain hose
16. Air inlet: (Back and side)
17. Air outlet
20. Earth terminal
18. Refrigerant piping and inter-unit cable
• It is inside of this cover.
Appearance of the outdoor unit may differ from some models.
List of Functions
121
Instruction
SiEBE12-625
„ Remote control
1
ON
2
C
5
HOME LEAVE
ON/OFF
3
POWERFUL
TEMP
6
4
7
MODE
SILENT
FAN
SWING
9
10
CANCEL
14
8
11
ON
15
OFF
TIMER
13
12
< ARC433A5, A6 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
HOME LEAVE operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
122
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
8. OUTDOOR UNIT SILENT button
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button:
11. ON TIMER button
12. OFF TIMER button
13. TIMER Setting button:
• It changes the time setting.
14. TIMER CANCEL button:
• It cancels the timer setting.
15. CLOCK button
List of Functions
SiEBE12-625
Instruction
FVK(X)S 25/35/50 B
„ Indoor Unit
„ Opening the front panel
How to open the front panel
Air outlet selection switch
This setting blows air from upper outlet only.
This setting automatically decides a blow
pattern depending on mode and conditions.
This setting is
recommended.
The unit is shipped from the
factory with this setting.
Air outlet
selection
CAUTION
Before opening the front panel, be sure to stop the operation and turn the breaker OFF.
Do not touch the metal parts on the inside of the indoor unit, as it may result in injury.
List of Functions
123
Instruction
SiEBE12-625
„ Outdoor Unit
„ Indoor Unit
1. Photocatalytic deodorizing filter and Air
purifying filter:
• These filters are attached to the inside of
the air filters.
2. Air outlet
3. Display
4. Front panel
5. Louvers (vertical blades)
• The louvers are inside of the air outlet.
6. Air inlet
7. Air filter
8. Flap (horizontal blade)
9. Operation Lamp (green)
10. TIMER lamp (yellow)
11. HOME LEAVE lamp (red)
12. Indoor unit ON/OFF switch:
• Push this switch once to start operation.
Push once again to stop it.
•
The operation mode refer to the following
table.
Mode
Temperature
setting
Air flow
rate
FLKS
COOL
22°C
AUTO
FLXS
AUTO
25°C
AUTO
•
This switch is useful when the remote
control is missing.
13. Signal receiver:
• Signals are recieved from the remote control.
• When the unit receives a signal, you will
hear a short beep
• Operation start ...........beep-beep
• Settings changed .......beep
• Operartion stop ..........beeeeep
14. Air outlet selection switch
15. Room temperature sensor:
• It senses the air temperature around the
unit
„ Outdoor Unit
19. Earth terminal
16. Air inlet: (Back and side)
17. Refrigerant piping and inter-unit cable
• It is inside of this cover.
18. Drain hose
20. Air outlet
Appearance of the outdoor unit may differ from some models.
124
List of Functions
SiEBE12-625
Instruction
„ Remote control
1
ON
2
C
5
HOME LEAVE
ON/OFF
3
POWERFUL
TEMP
6
4
7
MODE
SILENT
FAN
SWING
9
10
CANCEL
14
8
11
ON
15
OFF
TIMER
12
13
< ARC433A5, A6 >
1. Signal transmitter:
• It sends signals to the indoor unit.
2. Display:
• It displays the current settings.
(In this illustration, each section is shown
with all its displays ON for the purpose of
explanation.)
3. HOME LEAVE button:
HOME LEAVE operation
4. POWERFUL button:
POWERFUL operation
5. TEMPERATURE adjustment buttons:
• It changes the temperature setting.
6. ON/OFF button:
• Press this button once to start operation.
Press once again to stop it.
List of Functions
7. MODE selector button:
• It selects the operation mode.
(AUTO/DRY/COOL/HEAT/FAN)
8. SILENT button: OUTDOOR UNIT SILENT
operation
9. FAN setting button:
• It selects the air flow rate setting.
10. SWING button:
11. ON TIMER button
12. TIMER Setting button:
• It changes the time setting.
13. OFF TIMER button
14. TIMER CANCEL button:
• It cancels the timer setting.
15. CLOCK button
125
Instruction
2.4
SiEBE12-625
Preparation before Operation
„ To set the batteries
1. Slide the front cover to take it off.
2. Set two dry batteries (AAA).
3. Set the front cover as before.
Position + and
– correctly!
2
–
+
+
–
3
1
ATTENTION
„ About batteries
• When replacing the batteries, use batteries of the same type, and replace the two old batteries together.
• When the system is not used for a long time, take the batteries out.
• We recommend replacing once a year, although if the remote control display begins to fade or if reception deteriorates,
please replace with new alkali batteries. Do not use manganese batteries.
• The attached batteries are provided for the initial use of the system.
The usable period of the batteries may be short depending on the manufactured date of the air conditioner.
126
List of Functions
SiEBE12-625
Instruction
„ To operate the remote control
•
•
•
To use the remote control, aim the transmitter at the
indoor unit. If there is anything to block signals between
the unit and the remote control, such as a curtain, the
unit will not operate.
Do not drop the remote control. Do not get it wet.
The maximum distance for communication is about 7m.
Receiver
„
To fix the remote control holder on the wall
1. Choose a place from where the signals reach the
unit.
2. Fix the holder to a wall, a pillar, or similar location
with the screws procured locally.
3. Place the remote control in the remote control
holder.
Remote control
holder
Set.
To remove, pull it upwards.
ATTENTION
„ About remote control
• Never expose the remote control to direct sunlight.
• Dust on the signal transmitter or receiver will reduce the sensitivity. Wipe off dust with soft cloth.
• Signal communication may be disabled if an electronic-starter-type fluorescent lamp (such as inverter-type lamps) is in
the room. Consult the shop if that is the case.
• If the remote control signals happen to operate another appliance, move that appliance to somewhere else, or consult
the shop.
List of Functions
127
Instruction
SiEBE12-625
„ To set the clock
1. Press “CLOCK button”.
0:00 is displayed.
blinks.
2. Press “TIMER setting button” to set the
clock to the present time.
Holding down “
” or “
” button rapidly
increases or decreases the time display.
3. Press “CLOCK button”.
: blinks.
„ Turn the breaker ON
•
Turning ON the breaker opens the flap, then
closes it again. (This is a normal procedure.)
ì
NOTE
„ Tips for saving energy
• Be careful not to cool (heat) the room too much.
Keeping the temperature setting at a moderate level helps save energy.
• Cover windows with a blind or a curtain.
Recommended temperature setting
Blocking sunlight and air from outdoors increases the cooling (heating) effect.
For cooling: 26°C – 28°C
For heating: 20°C – 24°C
• Clogged air filters cause inefficient operation and waste energy. Clean them once in
about every two weeks.
„ Please note
• The air conditioner always consumes 15-35 watts of electricity even while it is not
operating.
• If you are not going to use the air conditioner for a long period, for example in spring or autumn, turn the breaker OFF.
• Use the air conditioner in the following conditions.
Mode
Operating conditions
If operation is continued out of this range
• A safety device may work to stop the operation.
COOL Outdoor temperature:<2MK(X)S40> 10 to
46 °C
(In multi system, it may work to stop the operation of the outdoor unit only.)
<2MXS52> -10 to 46 °C • Condensation may occur on the indoor unit and drip.
<3/4/5MK(X)S> 10 to 46°C
<RK(X)S -10> to 46°C
Indoor temperature: 18 to 32 °C
Indoor humidity: 80% max.
•
128
HEAT
Outdoor temperature:<2MKXS40> -10 to 15.5 °C • A safety device may work to stop the operation.
<2MXS52> -15 to 15.5 °C
<3/4/5MXS> -15 to 20°C
<RXS50> -15 to 18°C
Indoor temperature: 10 to 30 °C
DRY
Outdoor temperature:<2MK(X)S40> 10 to 46 °C
• A safety device may work to stop the operation.
<2MXS52> -10 to 46 °C
• Condensation may occur on the indoor unit and drip.
<3/4/5MK(X)S> -10 to 46°C
<R(X)S50> -10 to 46°C
Indoor temperature: 18 to 32 °C
Indoor humidity: 80% max.
Operation outside this humidity or temperature range may cause a safety device to disable the system.
List of Functions
SiEBE12-625
2.5
Instruction
AUTO · DRY · COOL · HEAT · FAN Operation
The air conditioner operates with the operation mode of your choice.
From the next time on, the air conditioner will operate with the same operation mode.
„ To start operation
1. Press “MODE selector button” and select a
operation mode.
• Each pressing of the button advances the
mode setting in sequence.
: AUTO
: DRY
: COOL
: HEAT
: FAN
<F(C)TKE>
ECONO
<F(C)TXE>
POWERFUL
2. Press “ON/OFF button” .
• The OPERATION lamp lights up.
4
ON/OFF
TEMP
2, 3
1
MODE
SWING
FAN
SILENT COMFORT SENSOR
5
ON
CANCEL
OFF
TIMER
„ To stop operation
3. Press “ON/OFF button” again.
• Then OPERATION lamp goes off.
„ To change the temperature setting
4. Press “TEMPERATURE adjustment button”
DRY or FAN mode
The temperature setting is not variable.
AUTO or COOL or HEAT mode
Press “
” to raise the temperature and press
“
” to lower the temperature.
Set to the temperature you like.
C
List of Functions
129
Instruction
SiEBE12-625
„ To change the air flow rate setting
5. Press “FAN setting button”.
DRY mode
AUTO or COOL or HEAT or FAN mode
Five levels of air flow rate setting from “
plus “
”“
” are available.
” to “
”
The air flow rate setting is not variable.
•
Indoor unit quiet operation
When the air flow is set to “
”, the noise from the indoor unit will become quieter.
Use this when making the noise quieter.
The unit might lose power when the air flow rate is set to a weak level.
NOTE
„ Note on HEAT operation
• Since this air conditioner heats the room by taking heat from outdoor air to indoors, the heating capacity becomes
smaller in lower outdoor temperatures. If the heating effect is insufficient, it is recommended to use another heating
appliance in combination with the air conditioner.
• The heat pump system heats the room by circulating hot air around all parts of the room. After the start of heating
operation, it takes some time before the room gets warmer.
• In heating operation, frost may occur on the outdoor unit and lower the heating capacity. In that case, the system
switches into defrosting operation to take away the frost.
• During defrosting operation, hot air does not flow out of indoor unit.
„ Note on COOL operation
• This air conditioner cools the room by blowing the hot air in the room outside, so if the outside temperature is high,
performance drops.
„ Note on DRY operation
• The computer chip works to rid the room of humidity while maintaining the temperature as much as possible. It
automatically controls temperature and fan strength, so manual adjustment of these functions is unavailable.
„ Note on AUTO operation
• In AUTO operation, the system selects an appropriate operation mode (COOL or HEAT) based on the room
temperature at the start of the operation.
• The system automatically reselects setting at a regular interval to bring the room temperature to usersetting level.
• If you do not like AUTO operation, you can manually select the operation mode and setting you like.
„ Note on air flow rate setting
• At smaller air flow rates, the cooling (heating) effect is also smaller.
130
List of Functions
SiEBE12-625
2.6
Instruction
Adjusting the Air Flow Direction
FTK(X)E 20/25/35/50 D
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blades (flaps)
1. Press “SWING button”.
The display will light up and the flaps
will begin to swing.
2. When the flaps have reached the desired
position, press “SWING button” once
more.
The display will go blank.
The flaps will stop moving.
ECONO
POWERFUL
ON/OFF
TEMP
MODE
SWING
FAN
SILENT COMFORT SENSOR
1, 2
3, 4
ON
CANCEL
OFF
TIMER
„ To adjust the vertical blades (louvers)
Hold the knob and move the louvres.
(You will find a knob on the left-side and the right-side
blades.)
• When the unit is installed in the corner of a room,
the direction of the louvers should be facing
away from the wall.
If they face the wall, the wall will block off the
wind, causing the cooling (or heating) efficiency
to drop.
List of Functions
131
Instruction
SiEBE12-625
„ To start COMFORT AIRFLOW operation
3. Press “COMFORT AIRFLOW button”.
• The flap position will change, preventing air from blowing directly on the occupants of the room.
• " " is displayed on the LCD
<COOL/DRY> The flap will go up.
<HEAT> The flap will go down
„ To cancel COMFORT AIRFLOW operation
4. Press “COMFORT AIRFLOW button” again.
• The flaps will return to the memory position from before COMFROT AIRFLOW mode.
• " " disappears from the LCD
Notes on COMFORT AIRFLOW operation
•
POWERFUL operation and COMFORT AIRFLOW operation cannot be used at the same time.
Priority is given to POWERFUL operation.
Notes on flaps and louvers angles
•
When “SWING button” is selected, the flaps swinging range depends on the
operation mode. (See the figure.)
„ ATTENTION
• Always use a remote control to adjust the flaps angle. If you attempt to move
it forcibly with hand when it is swinging, the mechanism may be broken.
• Be careful when adjusting the louvers. Inside the air outlet, a fan is rotating at
a high speed.
In DRY mode or COOL mode
When stop operation
Upper limit
Lower limit
In HEAT mode
When stop operation
Upper limit
Lower limit
In FAN mode
When stop operation
Upper limit
Lower limit
132
List of Functions
SiEBE12-625
Instruction
FTK(X)S 20/25/35 C
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blades (flaps)
1. Press “SWING button”.
The display will light up and the flaps
will begin to swing.
2. When the flap have reached the desired
position, press “SWING button” once
more.
The flap will stop moving.
“
”disappears from the LCD
List of Functions
133
Instruction
SiEBE12-625
„ To adjust the vertical blades (louvers)
Hold the knob and move the louvers.
(You will find a knob on the left-side and the right-side
blades.)
)
Notes on flaps and louvers angle
•
When “SWING button” is selected, the flaps swinging range depends on the
operation mode. (See the figure.)
„ ATTENTION
• Always use a remote control to adjust the flaps angle.
If you attempt to move it forcibly with hand when it is swinging, the mechanism
may be broken.
• Be careful when adjusting the louvers. Inside the air outlet, a fan is rotating at a
high speed.
In DRY mode or COOL mode
When stop operation
Upper limit in cooling
Lower limit in cooling
In HEAT or FAN mode
When stop operation
Upper limit in heating
Lower limit in heating
134
List of Functions
SiEBE12-625
Instruction
FLK(X) 25/35/50/60 A
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blade (flap)
1. Press “SWING button
”.
• “
”is displayed on the LCD and the
flaps will begin to swing.
2. When the flap have reached the desired
position, press “SWING button
” once
more.
• The flaps will stop moving.
• “ ”disappears from the LCD
1, 2
3, 4
„ To adjust the vertical blades (louvers)
1. Press “SWING button
”.
• “
” is displayed on the LCD
1. When the louvers have reached the desired position, press the “SWING button
more.
• The louvers will stop moving.
List of Functions
” once
135
Instruction
SiEBE12-625
„ To 3-D Airflow
1.3 Press the “SWING button
” and the “SWING button
”:
The “ ” and “
” display will light up and the flap and louvers will move in turn.
„ To cancel 3-D Airflow
2.4
Press either the “SWING button
” or the “SWING button
”.
Notes louvers angles
„
ATTENTION
• Always use a remote controller to adjust the louvers angles. In side the air outlet, a fan is rotating at a high speed.
Notes on flap angle
•
When “Swing button” is selected, the flaps swinging range depends on the
operation mode. (See the figure)
Three-Dimensional (3-D) Airflow
• Using three-dimensional airflow circulates cold air, which tends to collected
at the bottom of the room, and hot air, which tends to collect near the ceiling,
throughuit the room, preventing areas of cold and hot developing..
„ ATTENTION
• Always use a remote control to adjust the flaps angle.
If you attempt to move it forcibly with hand when it is swinging, the
mechanism may be broken.
• Be careful when adjusting the louvres. Inside the air outlet, a fan is rotating at
a high speed.
In DRY mode or COOL mode
STOP
COOL
approx. 10°~40°
DRY
approx. 5°~35°
In HEAT or FAN mode
STOP
HEAT
approx. 15°~55°
FAN
approx. 5°~55°
136
List of Functions
SiEBE12-625
Instruction
FTXG 25/35 E, CTXG 50 E
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blade (flap)
1. Press “SWING button
”.
• “
” is displayed on the LCD
2. When the flap have reached the desired
position, press “SWING button
” once
more.
• The flaps will stop moving.
• “ ”disappears from the LCD
1, 2
3, 4
5, 6
„ To adjust the vertical blades (louvers)
1. Press “SWING button
”.
• “
” is displayed on the LCD
1. When the louvers have reached the desired position, press the “SWING button
more.
• The louvers will stop moving.
” once
„ To 3-D Airflow
1.3 Press the “SWING button
” and the “SWING button
”:
The “ ” and “
” displaywill light up and the flap and louvers will move in turn
„ To cancel 3-D Airflow
2.4
List of Functions
Press either the “SWING button
” or the “SWING button
”:
137
Instruction
SiEBE12-625
„ To start COMFORT AIRFLOW operation
5. Press the “COMFORT AIRFLOW button”.
• The flap orientation will change, preventing air from blowing directly on the occupants of the
room.
• “
” is displayed on the LCD.
<COOL/DRY> The flap will go up.
<HEAT> The flap will go down
„ To cancel COMFORT AIRFLOW operation
5. Press the “COMFORT AIRFLOW button” again.
• The flaps will return to the memory position from before COMFORT AIRFLOW mode.
• “
” disappears from the LCD.
NOTE
•
When “SWING button ” is selected, the flap swinging range depends on the
operation mode. (See the figure.)
Three-Dimensional (3-D) Airflow
• Using three-dimensional airflow circulates cold air, wich tends to collected at the
bottom of the room, and hot air, which tends to collect near the ceiling, troughout
the room, preventing areas of cold and hot developing.
„ ATTENTION
• Always use a remote control to adjust the flap angle.
If you attempt to move it forcibly with hand when it is swinging, the mechanism may
be broken.
• Always use a remote control to adjust the louvers angles.
In COOL or DRY mode
COOL/DRY STOP
approx.
In HEAT or FAN mode
STOP
HEAT
approx.
FAN
approx.
In COMFORT AIRFLOW mode
COOL
STOP
HEAT
138
List of Functions
SiEBE12-625
Instruction
FTXS 25/35/50/60 B
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blade (flap)
1. Press “SWING button
”.
• “
” is displayed on the LCD and the
flaps will begin to swing
2. When the flaps have reached the desired
position, press “SWING button
” once
more.
• The flap will stop moving.
• “ ”disappears from the LCD
ON
C
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
1, 2
CANCEL
OFF
TIMER
List of Functions
139
Instruction
SiEBE12-625
„ To adjust the vertical blades (louvers)
•
•
•
When adjusting the louver, use a robust and
stable stool and watch your steps carefully.
Hold the knob and move the louvers.
(You will find a knob on the left side and the
right side blades.)
Notes on flap and louvers angles.
•
Unless [SWING] is selected, you should set the flap at a near-horizontal
angle in COOL or DRY mode to obtain the best performance.
• In COOL or DRY mode, if the flap is fixed at a downward position, the flap
automatically moves in about 60 minutes to prevent condensation on it.
„ ATTENTION
• Always use a remote control to adjust the flap angle.
If you attempt to move it forcibly with hand when it is swinging, the
mechanism may be broken.
• Be careful when adjusting the louvers. Inside the air outlet, a fan is
rotating at a high speed.
140
DRY
COOL
FAN
HEAT
List of Functions
SiEBE12-625
Instruction
FTXS 25/35/50/60 B
You can adjust the air flow direction to increase
your comfort.
„ To adjust the horizontal blade (flap)
1. Press “SWING button
”.
• “
” is displayed on the LCD and the
flaps will begin to swing
2. When the flaps have reached the desired
position, press “SWING button
” once
more.
• The flaps will stop moving.
• “ ”disappears from the LCD
ON
C
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
1, 2
CANCEL
OFF
TIMER
„ To adjust the vertical blades (louvers)
Hold the knob and move the louver.
(You will find a knog on the lift-side and the
right-side blades.)
Notes on flap and louvers angle.
•
Unless [SWING] is selected, you should set the flap at a near-horizontal angle in
HEAT mode and at a upward position in COOL or DRY mode to obtain the best COOL/DRY
performance.
HEAT
„ ATTENTION
• When adjusting the flap by hand, turn off the unit, and use the remote controller
to restart the unit.
• Be careful when adjusting the louvers. Inside the air outlet, a fan is rotating at a high speed.
List of Functions
141
Instruction
SiEBE12-625
„ Air flow selection
•
make air flow selection acoording to what suits you.
When setting the air flow selection switch to
•
.
Air conditioner automatically decides the appropriate blowing pattern depending on the
operating mode/situation.
Operating mode
Situation
•
When the room has become fully
cool, or when one hour has
passed since turning on the air
conditioner.
•
At start of operation or other
times when the room is not fully
cooled.
At times other than below.
(Normal time.)
COOL mode
•
Blowing pattern
•
So that air does not come
into direct contact with
people, air is blown under
air outlet, room
temperature is equlides.
•
Air is blown from the upper
and lower air outlets for
high speed cooling during
COOL mode, and for filling
the room with warm air
during HEAT mode.
• At start or when air temperature
• So that air does not come
is low.
into direct contact with
people. Air is blown upper
air outlet.
During Dry mode, so that cold air does not come into direct contact with people, air is blown
upper air outlet.
HEAT mode
•
When setting the air outlet selection switch to
•
•
.
Regardless of the operating mode or situation, air blows from the upper air outlet.
Use this switch when you do not want air coming out of the lower air outlet. (While sleeping
etc...)
CAUTION
•
•
142
Do not try to adjusting the flap by hand.
When adjusting by hand, the mechanism may not operate properly or condensation may drip from air outlets.
List of Functions
SiEBE12-625
2.7
Instruction
POWERFUL Operation
Powerful operation quickly maximizes the cooling
(heating) effect in any operation mode. You can get
the maximum capacity.
„ To start POWERFUL operation
1. Press “POWERFUL button”.
• POWERFUL operation ends in 20 minutes.
Then the system automatically operates
again with the settings which were used
before POWERFUL operation.
• When using POWERFUL operation, there
are some functions which are not available.
• “
” is displayed on the LCD.
„ To cancel POWERFUL operation
2. Press “POWERFUL button” again.
• “
” disappears from the LCD.
NOTE
„ Notes on POWERFUL operation
• POWERFUL Operation cannot be used together with ECONO, SILENT or COMFORT Operation. Priority is given to the
function of whichever button is pressed last.
• POWERFUL Operation can only be set when the unit is running. Pressing the operation stop button causes the settings
to be canceled, and the “
” disappears from the LCD.
• In COOL and HEAT mode
To maximize the cooling (heating) effect, the capacity of outdoor unit must be increased and the air flow rate be fixed to
the maximum setting.
The temperature and air flow settings are not variable.
• In DRY mode
The temperature setting is lowered by 2.5°C and the air flow rate is slightly increased.
• In FAN mode
The air flow rate is fixed to the maximum setting.
• When using priority-room setting
See “Note for multi system”.
List of Functions
143
Instruction
2.8
SiEBE12-625
OUTDOOR UNIT SILENT Operation
OUTDOOR UNIT SILENT operation lowers the
noise level of the outdoor unit by changing the
frequency and fan speed on the outdoor unit. This
function is convenient during night.
„ To start OUTDOOR UNIT SILENT operation
1. Press “SILENT button”.
• “
” is displayed on the LCD
„ To cancel OUTDOOR UNIT SILENT operation
2. Press “SILENT button” again.
• “
” disappears from the LCD
ECONO
POWERFUL
ON/OFF
TEMP
MODE
SWING
FAN
SILENT COMFORT SENSOR
1, 2
ON
CANCEL
OFF
TIMER
NOTE
„ Note on OUTDOOR UNIT SILENT operation
• If using a multi system, this function will work only when the OUTDOOR UNIT SILENT operation is set on all operated
indoor units.
However, if using priority-room setting, see “Note for multi system”.
• This function is available in COOL, HEAT, and AUTO modes.
(This is not available in FAN and DRY mode.)
• POWERFUL operation and OUTDOOR UNIT SILENT operation cannot be used at the same time.
Priority is given to the function of whichever button is pressed last.
144
List of Functions
SiEBE12-625
2.9
Instruction
ECONO Operation
ECONO operation is a function which enables
efficient operation by lowering the maximum power
consumption value.
„ To start ECONO operation
1. Press “SILENT button”.
• “
” is displayed on the LCD
„ To cancel ECONO operation
2. Press “ECONO button” again.
• “
” disappears from the LCD
1, 2
ECONO
POWERFUL
ON/OFF
TEMP
MODE
SWING
FAN
SILENT COMFORT SENSOR
ON
CANCEL
OFF
TIMER
NOTE
•
•
•
•
•
ECONO Operation can only be set when the unit is running. Pressing the operation stop button causes the settings to
be canceled, and the “
” disappears from the LCD.
ECONO Operation is a function which enables efficient operation by limiting the power consumption of the outdoor unit
(operating frequency).
ECONO Operation functions in AUTO, COOL, DRY and HEAT modes. The fan strength does not change in ECONO
operation.
POWERFUL operation and ECONO operation cannot be used at the same time.
Priority is given to POWERFUL operation.
Power consumption may not drop even if ECONO operation is used, when the level of power consumption is already
low.
List of Functions
145
Instruction
SiEBE12-625
2.10 HOME LEAVE Operation
HOME LEAVE operation is a function which allows
you to record your preferred temperature and air
flow rate settings.
„ To start HOME LEAVE operation
1. Press “HOME LEAVE button” .
• “
” is displayed on the LCD
• The HOME LEAVE lamp lights up.
1, 2
„ To cancel HOME LEAVE operation
2. Press “HOME LEAVE button” again.
• “
” disappears from the LCD
• The HOME LEAVE lamp goes off.
Before using HOME LEAVE operation.
„ To set the temperature and air flow rate for HOME LEAVE operation
When using HOME LEAVE operation for the first time, please set the temperature and air flow rate for HOME LEAVE
operation. Record your preferred temperature and air flow rate.
Initial setting
Selectable range
temperature
Air flow rate
temperature
Air flow rate
Cooling
25°C
AUTO
18-32°C
5 step, AUTO and SILENT
Heating
25°C
AUTO
10-30°C
5 step, AUTO and SILENT
3. Press “HOME LEAVE button”. Make sure “
” is displayed in the remote control display.
4. Adjust the set temperature with “
” or “
” as you like.
5. Adjust the air flow rate with “FAN” setting button as you like.
Home leave operation will run with these settings the next time you use this function. To change the recorded information,
repeat steps 1 – 3.
146
List of Functions
SiEBE12-625
Instruction
„ What’s the HOME LEAVE operation
Is there a set temperature and air flow rate which is most comfortable, a set temperature and air flow
rate which you use the most? HOME LEAVE operation is a function that allows you to record your
favorite set temperature and air flow rate. You can start your favorite operation mode simply by
pressing the HOME LEAVE button on the remote control. This function is convenient in the following
situations.
„ Useful in these cases.
1. Use as an energy-saving mode
Set the temperature 2-3°C higher (cooling) or lower (heating) than normal. Setting the fan strength
to the lowest setting allows the unit to be used in energy-saving mode. Also convenient for use
while you are out or sleeping.
•
Every day before you leave the house...
When you go out, push the “HOME
LEAVE Operation” button, and the
air conditioner will adjust capacity
to reach the preset temperature for
HOME LEAVE Operation.
•
When you return, you will be
welcomed by a comfortably air
conditioned room.
Push the “HOME LEAVE
Operation” button again, and the
air conditioner will adjust capacity
to the set temperature for normal
operation.
The unit will maintain the
temperature in the room at a
comfortable level while you
sleep.
When you enter the living room in
the morning, the temperature will
be just right.
Disengaging HOME LEAVE
Operation will return the
temperature to that set for normal
operation. Even the coldest
winters will pose no problem!
Before bed...
Set the unit to HOME LEAVE
Operation before leaving the living
room when going to bed.
2. Use as a favorite mode
Once you record the temperature and air flow rate settings you most often use, you can retrieve
them by pressing HOME LEAVE button. You do not have to go through troublesome remote control
operations.
NOTE
•
•
•
•
•
•
Once the temperature and air flow rate for HOME LEAVE operation are set, those settings will be used whenever HOME
LEAVE operation is used in the future. To change these settings, please refer to the “Before using HOME LEAVE operation”
section above.
HOME LEAVE operation is only available in COOL and HEAT mode. Cannot be used in AUTO, DRY, and FAN mode.
HOME LEAVE operation runs in accordance with the previous operation mode (COOL or HEAT) before using HOME
LEAVE operation.
HOME LEAVE operation and POWERFUL operation cannot be used at the same time.
Last button that was pressed has priority.
The operation mode cannot be changed while HOME LEAVE operation is being used.
When operation is shut off during HOME LEAVE operation, using the remote control or the indoor unit ON/OFF switch,
“
” will remain on the remote control display.
List of Functions
147
Instruction
SiEBE12-625
2.11 INTELLIGENT EYE Operation
FTK(X)E 25/35 B
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
„ To start INTELLIGENT EYE operation
1. Press “SENSOR button”.
• “
” is displayed on the LCD
„ To cancel the INTELLIGENT EYE operation
2. Press “SENSOR button” again.
• “
” disappears from the LCD
ECONO
POWERFUL
ON/OFF
TEMP
[EX.]
When somebody in the room
• Normal operation
MODE
SWING
FAN
SILENT COMFORT SENSOR
1, 2
ON
When nobody in the room
• 20 min. after, start energy
operation.
CANCEL
OFF
saving
TIMER
Somebody back in the room
• Back to normal operation.
148
List of Functions
SiEBE12-625
Instruction
“INTELLIGENT EYE” is useful for Energy Saving
„ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +2°C in dry mode from set temperature.
• Decrease the air flow rate slightly in fan operation. (In FAN mode only).
Notes on “INTELLIGENT EYE”
•
Application range is as follows.
Vertical angle 90°
(Side View)
Horizontal angle 110°
(Top View)
•
•
•
•
•
90°
7m
55° 55°
7m
Sensor may not detect moving objects further than 7m away. (Check the application range)
Sensor detection sensitivity changes according to indoor unit location, the speed of passersby, temperature range, etc.
The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of mirrors as passersby.
INTELLIGENT EYE operation will not go on during powerful operation.
Night set mode will not go on during you use INTELLIGENT EYE operation.
CAUTION
•
•
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can detect objects it shouldn’t as well
as not detect objects it should.
Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction
List of Functions
149
Instruction
SiEBE12-625
FTK(X)D 50/60/71 B
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
„ To start INTELLIGENT EYE operation
1. Press “SENSOR button”.
• “
” is displayed on the LCD
„ To cancel the INTELLIGENT EYE operation
2. Press “SENSOR button” again.
• “
” disappears from the LCD
[EX.]
When somebody in the room
• Normal operation
When nobody in the room
• 20 min. after, start energy
operation.
saving
Somebody back in the room
• Back to normal operation.
150
List of Functions
SiEBE12-625
Instruction
„ To adjust the angle of the INTELLIGENT EYE sensor
•
You can adjust the angle of the INTELLIGENT
EYE sonsor to increase the detection area.
(Adjustable angle: 15° to right and left of
centre)
INTELLIGENT EYE
sensor
•
•
Gently push and slide the sensor to adjust the
angle.
After adjusting the angle, wipe the sensor
gently with a clean cloth, being careful not to
scratch the sensor.
Moving the sensor to the left
Moving the sensor to the right
“INTELLIGENT EYE” is useful for Energy Saving
„ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +1°C in dry mode from set temperature.
• Decrease the air flow rate slightly in fan operation. (In FAN mode only)
Notes on “INTELLIGENT EYE”
•
Application range is as follows.
Vertical angle 90˚
(Side View)
Horizontal angle 110˚
(Top View)
•
•
•
•
•
80˚
5m
50˚ 50˚
5m
Sensor may not detect moving objects further than 5m away. (Check the application range)
Sensor detection sensitivity changes according to indoor unit location, the speed of passersby, temperature range, etc.
The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of mirrors as passersby.
INTELLIGENT EYE operation will not go on during powerful operation.
Night set mode will not go on during you use INTELLIGENT EYE operation.
CAUTION
•
•
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can detect objects it shouldn’t as well
as not detect objects it should.
Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction
List of Functions
151
Instruction
SiEBE12-625
FTK(X)S 50/60/71 E, FTK(X)S 71 B
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
„ To start INTELLIGENT EYE operation
1. Press “SENSOR button”.
• “
” is displayed on the LCD
„ To cancel the INTELLIGENT EYE operation
2. Press “SENSOR button” again.
• “
” disappears from the LCD
[EX.]
When somebody in the room
1, 2
• Normal operation
When nobody in the room
• 20 min. after, start energy
operation.
saving
Somebody back in the room
• Back to normal operation.
152
List of Functions
SiEBE12-625
Instruction
“INTELLIGENT EYE” is useful for Energy Saving
„ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +1°C in dry mode from set temperature.
• Decrease the air flow rate slightly in fan operation. (In FAN mode only)
Notes on “INTELLIGENT EYE”
•
Application range is as follows.
Vertical angle 90˚
(Side View)
Horizontal angle 110˚
(Top View)
•
•
•
•
•
90˚
7m
55˚ 55˚
7m
Sensor may not detect moving objects further than 7m away. (Check the application range)
Sensor detection sensitivity changes according to indoor unit location, the speed of passersby, temperature range, etc.
The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of mirrors as passersby.
INTELLIGENT EYE operation will not go on during powerful operation.
Night set mode will not go on during you use INTELLIGENT EYE operation.
CAUTION
•
•
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can detect objects it shouldn’t as well
as not detect objects it should.
Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction
List of Functions
153
Instruction
SiEBE12-625
FTK(X)S 50/60/71 E, FTK(X)S 71 B
“INTELLIGENT EYE” is the infrared sensor which
detects the human movement.
„ To start INTELLIGENT EYE operation
1. Press “SENSOR button”.
• “
” is displayed on the LCD
„ To cancel the INTELLIGENT EYE operation
2. Press “SENSOR button” again.
• “
” disappears from the LCD
[EX.]
1, 2
When somebody in the room
• Normal operation
• The INTILLIGENT EYE lamp lights up
When somebody in the room
• 20 min. after, start energy
saving operation.
• The INTILLIGENT EYE lamp goes off
Somebody back in the room
• Back to normal operation
• The INTILLIGENT EYE lamp lights up
154
List of Functions
SiEBE12-625
Instruction
“INTELLIGENT EYE” is useful for Energy Saving
„ Energy saving operation
• Change the temperature –2°C in heating / +2°C in cooling / +2°C in dry mode from set temperature.
• Decrease the air flow rate slightly in fan operation. (In FAN mode only)
Notes on “INTELLIGENT EYE”
•
Application range is as follows.
Vertical angle 90˚
(Side View)
Horizontal angle 110˚
(Top View)
•
•
•
•
•
90˚
7m
55˚ 55˚
7m
Sensor may not detect moving objects further than 7m away. (Check the application range)
Sensor detection sensitivity changes according to indoor unit location, the speed of passersby, temperature range, etc.
The sensor also mistakenly detects pets, sunlight, fluttering curtains and light reflected off of mirrors as passersby.
INTELLIGENT EYE operation will not go on during powerful operation.
Night set mode will not go on during you use INTELLIGENT EYE operation.
CAUTION
•
•
Do not place large objects near the sensor.
Also keep heating units or humidifiers outside the sensor’s detection area. This sensor can detect objects it shouldn’t as well
as not detect objects it should.
Do not hit or violently push the INTELLIGENT EYE sensor. This can lead to damage and malfunction
List of Functions
155
Instruction
SiEBE12-625
2.12 TIMER Operation
Timer functions are useful for automatically
switching the air conditioner on or off at night or in
the morning. You can also use OFF TIMER and ON
TIMER in combination.
„ To use OFF TIMER operation
•
Check that the clock is correct.
If not, set the clock to the present time.
1. Press “OFF TIMER button”.
0:00 is displayed.
blinks.
2. Press “TIMER Setting button until the time
setting reaches the point you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the
setting rapidly.
3. Press “OFF TIMER button” again.
• The TIMER lamp lights up.
ECONO
POWERFUL
ON/OFF
TEMP
MODE
SWING
FAN
SILENT COMFORT SENSOR
ON
CANCEL
2
4
OFF
TIMER
1, 3
„ To cancel the OFF TIMER operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
Notes
•
•
When TIMER is set, the present time is not displayed.
Once you set ON, OFF TIMER, the time setting is kept in the memory. (The memory is canceled when remote control
batteries are replaced.)
• When operating the unit via the ON/OFF Timer, the actual length of operation may vary from the time entered by the user.
„ NIGHT SET MODE
When the OFF TIMER is set, the air conditioner automatically adjusts the temperature setting (0.5°C up in COOL, 2.0°C
down in HEAT) to prevent excessive cooling (heating) for your pleasant sleep.
156
List of Functions
SiEBE12-625
Instruction
„ To use ON TIMER operation
•
Check that the clock is correct. If not, set the
clock to the present time.
1. Press “ON TIMER button”.
6:00 is displayed.
blinks.
2. Press “TIMER Setting button” until the time
setting reaches the point you like.
• Every pressing of either button increases or
decreases the time setting by 10 minutes.
Holding down either button changes the
setting rapidly.
3. Press “ON TIMER button” again.
• The TIMER lamp lights up.
„ To cancel ON TIMER operation
4. Press “CANCEL button”.
• The TIMER lamp goes off.
„ To combine ON TIMER and OFF TIMER
•
A sample setting for combining the two timers is
shown below.
Display
(Example)
Present time: 11:00 p.m.
(The unit operating)
OFF TIMER at 0:00 a.m.
ON TIMER at 7:00 a.m.
Combined
ATTENTION
„ In the following cases, set the timer again.
• After a breaker has turned OFF.
• After a power failure.
• After replacing batteries in the remote control.
List of Functions
157
Instruction
SiEBE12-625
2.13 Note for Multi System
<< What is a “Multi System”? >>
This system has one outdoor unit connected to multiple indoor units.
Functions depend on the model. See the list of functions and applicable models (*2) on the next page.
„ Selecting the Operation Mode
1. With the Priority Room Setting present but inactive or
not present
A
When more than one indoor unit is operating, priority is
room
Outdoor
given to the first unit that was turned on.
unit
B
In this case, set the units that are turned on later to the
room
Living
same operation mode (*1) as the first unit.
room
Otherwise, they will enter the Standby Mode, and the
C
operation lamp will flash; this does not indicate
room
malfunction.
(*1)
• COOL, DRY and FAN mode may be used at the same
time.
• AUTO mode automatically selects COOL mode or HEAT mode based on the room temperature.
Therefore, AUTO mode is available when selecting the same operation mode as that of the
room with the first unit to be turned on.
<CAUTION>
Normally, the operation mode in the room where the unit is first run is given priority, but the
following situations are exceptions, so please keep this in mind.
If the operation mode of the first room is FAN Mode, then using Heating Mode in any room after
this will give priority to heating. In this situation, the air conditioner running in FAN Mode will go on
standby, and the operation lamp will flash.
2. With the Priority Room Setting active
See “Priority Room Setting” on the next page.
„ NIGHT QUIET Mode (Available only for cooling operation)
NIGHT QUIET Mode requires initial programming during installation. Please consult your retailer or
dealer for assistance.
NIGHT QUIET Mode reduces the operation noise of the outdoor unit during the night time hours to
prevent annoyance to neighbors.
• The NIGHT QUIET Mode is activated when the temperature drops 5°C or more below the highest
temperature recorded that day. Therefore, when the temperature difference is less than 5°C, this
function will not be activated.
• NIGHT QUIET Mode reduces slightly the cooling efficiency of the unit.
„ OUTDOOR UNIT SILENT Operation
1. With the Priority Room Setting present but inactive or not present
When using the OUTDOOR UNIT SILENT operation feature with the Multi system, set all indoor
units to OUTDOOR UNIT SILENT operation using their remote controls.
When clearing OUTDOOR UNIT SILENT operation, clear one of the operating indoor units using
their remote control.
However OUTDOOR UNIT SILENT operation display remains on the remote control for other
rooms.
We recommend you release all rooms using their remote controls.
2. With the Priority Room Setting active
See “Priority Room Setting” on the next page.
„ Cooling / Heating Mode Lock (Available only for heat pump models)
The Cooling / Heating Mode Lock requires initial programming during installation.Please consult your
retailer or dealer for assistance. The Cooling / Heating Mode Lock sets the unit forcibly to either
Cooling or Heating Mode. This function is convenient when you wish to set all indoor units connected to
the Multi system to the same operation mode.
158
List of Functions
SiEBE12-625
Instruction
„ Priority Room Setting
The Priority Room Setting requires initial programming during installation. Please consult your
retailer or dealer for assistance.
The room designated as the Priority Room takes priority in the following situations;
1. Operation Mode Priority
As the operation mode of the Priority Room takes precedence, the user can select a different
operation mode from other rooms.
<Example>
* Room A is the Priority Room in the examples.
When COOL mode is selected in Room A while operating the following modes in Room B,C and
D:
Operation mode in Room B, C and D
COOL or DRY or FAN
HEAT
AUTO
Status of Room B, C and D when the unit in Room
A is in COOL mode
Current operation mode maintained
The unit enters Standby Mode. Operation resumes
when the Room A unit stops operating.
If the unit is set to COOL mode, operation
continues. If set to HEAT mode, it enters Standby
Mode. Operation resumes when the Room A unit
stops operating.
2. Priority when POWERFUL operation is used
<Example>
* Room A is the Priority Room in the examples.
The indoor units in Rooms A,B,C and D are all operating. If the unit in Room A enters
POWERFUL operation, operation capacity will be concentrated in Room A. In such a case, the
cooling (heating) efficiency of the units in Rooms B,C and D may be slightly reduced.
3. Priority when using OUTDOOR UNIT SILENT operation
<Example>
* Room A is the Priority Room in the examples.
Just by setting the unit in Room A to SILENT operation, the air conditioner starts OUTDOOR
UNIT SILENT operation.
You don’t have to set all the operated indoor units to SILENT operation.
List of Functions
159
Instruction
SiEBE12-625
2.14 Care and Cleaning
FTK(X)E 20/25/35/50 D
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Hold the panel by the tabs on the two sides and
lift it until it stops with a click.
2. Remove the front panel.
• Lift the panel up, slide it slightly to the right, and
remove it from the horizontal axle.
3. Clean the front panel
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the panel with water, dry it
with cloth, dry it up in the shade after washing.
4. Attach the front panel
• Set the 3 keys of the front panel into the slots
and push them in all the way.
• Close the front panel slowly and push the panel
at the 3 points.
(1 on each sides and 1 in the middle.)
• Check to see if the rotating axis in the upper
center section is moving.
Fit the key
into the slot.
CAUTION
•
•
•
•
•
160
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the grille securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
SiEBE12-625
Instruction
Filters
1. Open the front panel.
2. Pull out the air filters.
• Push a little upwards the tab at the center of
each air filter, then pull it down.
3. Take off the Titanium Apatite Photocatalytic Air
Purifying Filter.
• Hold the recessed parts of the frame and
unhook the four claws.
4. Clean or replace each filter.
See figure.
5. Set the air filter and Titanium Apatite
Photocatalytic Air-Purifying filter as they were
and close the front panel.
• Insert claws of the filters into slots of the front panel.
Close the front panel slowly and push the panel at
the 3 points. (1 on each sides and 1 in the middle.)
Titanium Apatite
Photocatalytic
Air-Purifying Filter
Filter frame
Air filter
Tab
Push
„ Air Filter
1. Wash the air filters with water or clean them with vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Titanium Apatite Photocatalytic Air-Purifying Filter.
The Titanium apatite Photocatalytic Air-Purifying filger cn be renewed by
washing it with water every 6 months. We recommend replacing it once every 3
years.
Ta b
[Maintenance]
1.
2.
3.
4.
5.
Remove dust with a vacuum cleaner and wash it lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
Do not remove filter from frame when washing with water.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water
from it.
[Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
List of Functions
161
Instruction
SiEBE12-625
NOTE
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
To order Titanium Apatite Photocatalytic Air-Purifying filter contact to the service shop there you bought the air
conditioner.
Dispose of old filters as burnable waste.
Item
Titanium Apatite Photocatalytic Air-Purifying Filter.
(without frame) 1 set
Part No.
KAF970A46
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “fan only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “fan” operation.
• Press “ON/OFF” button and start operation.
2. Clean the air filters and set them again.
3. Take out batteries from the remote control.
4. Turn OFF the breaker for the room air conditioner.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
162
List of Functions
SiEBE12-625
Instruction
FTK(X)D 50/60/71 B
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Hold the panel by the tabs on the two sides and
lift it until it stops with a click.
2. Remove the front panel.
• Open the front panel with one hand, release
the lock by sliding down the knob with the other
hand.
• To remove the front panel, pull it toward
yourself with both hands.
3. Clean the front panel
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the panel with water, dry it with
cloth, dry it up in the shade after washing.
4. Attach the front panel
• Align the rotation dowels on the left and right of the front panel
with the slots, then push them all the way in.
• Close the front panel slowly. (Press the panel at both sides and
the center.)
Fit the key
into the slot.
CAUTION
•
•
•
•
•
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the grille securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
163
Instruction
SiEBE12-625
Filters
1. Open the front panel.
2. Pull out the air filters.
• Push a little upwards the tab at the center of
each air filter, then pull it down.
3. Take off the air purifying filter with
photocatalytic deodorizing function.
• Hold the recessed parts of the frame and
unhook the four claws.
4. Clean or replace each filter.
See figure.
5. Set the air filter, air purifying filter with photocalytic
deodorizing function as they were and close the front
panel.
• Press the front panel at both sides and the center.
Air purifying filter
with photocatalytic
deodorizing
Air filter
function
Push
„ Air Filter
1. Wash the air filters with water or clean them with vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Air purifying filter with photocatalytie deodorizing function. (gray)
The Air purifying filter wiht photocatalytic deodorizing function can be
renewed by washing it with water once every 6 months. We recommend
replacing it once every 3 years
[Maintenance]
1.
2.
3.
4.
5.
Remove dust with a vacuum cleaner and wash lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
Do not remove filter from frame when washing with water.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water
from it.
[Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
164
List of Functions
SiEBE12-625
Instruction
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the earth wire is not disconnected or broken.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “fan only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “fan” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote controller.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
NOTE
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
To order air purifying filter with photocatalytic deodorizing function contact to the service shop there you bought the air
conditioner.
Dispose of old air filters as burnable waste.
Item
Air purifying filter with photocatalytie deodorizing function.
(without frame) 1 set
Air purifying filter with photocatalytic deodorizing function.
(without frame) 1 set
List of Functions
Part No.
KAF918A43
KAF918A44
165
Instruction
SiEBE12-625
CDK(X)D 25/35/50/60 C
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Hold the panel by the tabs on the two sides and
lift it until it stops with a click.
2. Remove the front panel.
• Open the front penel further while sliding it to
either the left or right and pulling it toward you;
This will disconnect the rotation dowel on one
side. Then disconnect the rotation dowel on the
other side in the same manner.
3. Clean the front panel
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the panel with water, dry it with cloth, dry it up in the shade after washing.
4. Attach the front panel
• Align the rotation dowels on the left and right of the front panel
with the slots, then push them all the way in.
• Close the front panel slowly. (Press the panel at both sides and
the center.)
CAUTION
•
•
•
•
•
166
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the grille securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
SiEBE12-625
Instruction
Filters
1. Open the front panel.
2. Pull out the air filters.
• Push a little upwards the tab at the center of
each air filter, then pull it down.
3. Take off the Titanium Apatite
Photocatalytic Air-Purifying
filter.
• Press the top of the aircleaning filter onto the tabs
(3 tabs at top). Then press
the bottom of the filter up
slightly, and press it onto the
tabs (3 at bottom).
tabs (3 tabs at top)
tabs (3 at bottom)
4. Clean or replace each filter.
See figure.
5. Set the air filter and the Titanium Apatite Photocatalytic
Air-Purifying filter as they were and close the front
panel.
• Press the front panel at both sides and the center.
„ Air Filter
1. Wash the air filters with water or clean them with vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Titanium Apatite Photocatalytic Air-purifying Filter (gray)
The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed by washing it with water once
every 6 months. We recommend replacing it once every 3 years.
[Maintenance]
1.
2.
3.
4.
Remove dust with a vacuum cleaner and wash lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water
from it.
[Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
List of Functions
167
Instruction
SiEBE12-625
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
NOTE
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
To order Titanium Apatite Photocatalytic Air-Purifying Filter contact to the service shop there you bought the air conditioner.
Dispose of old filters as burnable waste.
Item
Titanium Apatite Photocatalytic Air-Purifying Filter.
(without frame) 1 set
168
Part No.
KAF952B42
List of Functions
SiEBE12-625
Instruction
FTK(X)S 71B
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front grille
1. Open the front grille.
• Hold the panel by the tabs on the two sides and
lift it until it stops with a click.
2. Remove the front grille.
• Open the front panel further while sliding it to
either the left or right and pulling it toward you.
This will disconnect the rotation dowel on one
side; Then disconnect the rotation dowel on the
other side in the same manner.
3. Clean the front grille
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the grille with water, dry it with
cloth, dry it up in the shade after washing.
4. Attach the front grille
• Align the rotation dowels on the left and right of the front panel
with the slots, then push them all the way in.
• Close the front panel slowly. (Press the panel at both sides and
the center.)
CAUTION
•
•
•
•
•
•
When the packaging materials are attached to the front panel, please remove them.
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps
carefully.
When removing or attaching the front panel, support the grille securely with hand to prevent it from
falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils,
polishing compound, scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
169
Instruction
SiEBE12-625
Filters
1. Open the front panel.
2. Pull out the air filters.
• Push a little upwards the tab at the center of
each air filter, then pull it down.
3. Take off the air purifying filter with
photocatalytic deodorizing function.
• Press the top of the aircleaning filter
onto the tabs (3 tabs at top). Then
press the bottom of the filter up
slightly, and press it onto the tabs (2
at bottom)(3 at bottom).
tabs (3 tabs at top)
tabs (2 at bottom)
50class
tabs (3 tabs at top)
tabs (3 at bottom)
60,71class
4. Clean or replace each filter.
See figure.
5. Set the air filter, air purifying filter with photocalytic
deodorizing function as they were and close the front
grille.
• Press the front panel at both sides and the center.
„ Air Filter
1. Wash the air filters with water or clean them with vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Air purifying filter with photocatalytic deodorizing function. (gray)
The Air purifying filter with photocatalytic deodorizing function can be renewed by washing it with water
once every 6 months. We recommend replacing it once every 3 years.
[Maintenance]
1.
2.
3.
4.
Remove dust with a vacuum cleaner and wash lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water
from it.
[Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
170
List of Functions
SiEBE12-625
Instruction
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
NOTE
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
To order air purifying filter with photocatalytic deodorizing function contact to the service shop there you bought the air
conditioner.
Dispose of old air filters as burnable waste..
Item
Air purifying filter with photcatalytic deodorizing function.
(without frame) 1 set
List of Functions
Part No.
KAF952A42
171
Instruction
SiEBE12-625
FTK(X)S 71B
CAUTION
• Before cleaning, be sure to stop the operation and turn the breaker OFF.
• Always shut down the unit (and close the anel) before doing any work.
Opening the panel during operation may cause the panel to fall off.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Open the fornt panel by placing a finger on the
panel tab on either side of the front panel.
2. Remove the front panel.
• With the front panel open so that is almost
horizontal, slide it to the right.
The revolving axis on the left will come off.
The revolving axis on the right can be removed
by sliding the front panel to the left.
3. Clean the front panel
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the front panel with water, dry
it with cloth, dry it up in the shade after washing.
4. Attach the front panel
• Align the rotation dowels on the left and right of the
front panel with the slots, then push them all the way
in.
• Close the front panel slowly. (Press the panel at both
sides and the center.)
CAUTION
•
•
•
•
•
172
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the grille securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
SiEBE12-625
Instruction
Filters
1. Open the front panel.
• Open the front panel by placing a finger on the
panel tab on either side of the front panel and
then secure it using the supporting plate on the
right.
Supporting plate
2. Pull out the air filters..
• Push a little upwards the tab at the center of
each air filter, then pull it down.
Titanium Apatite
Photocatalytic
Air-Purifying Filter
Air filter
Filter frame
3. Take off the Titanium Apatite Photocatalytic
Air-Purifying Filter.
• Hold the recessed parts of the frame and
unhook the four claws
4. Clean or replace each filter.
See figure.
Tab
5. Set the air filter and the Titanium Apatite Photocatalytic AirPurifying filter as they were and close the front panel.
Push
• Be sure to insert the two tabs below.
• Return the supporting plate to its previous position.
• Press either side of the front panel.
„ Air Filter
1. Wash the air filters with water or clean them with vacuum cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Titanium Apatite Photocatalytic Air-purifying Filter (gray)
The Titanium Apatite Photocatalytic Air-Purifying Filter can be renewed by
washing it with water once every 6 months. We recommend replacing it once
every 3 years.
Tab
[Maintenance]
1.
2.
3.
4.
5.
Remove dust with a vacuum cleaner and wash lightly with water.
If it is very dirty, soak it for 10 to 15 minutes in water mixed with a neutral cleaning agent.
Do not remove filter from frame when washing with water.
After washing, shake off remaining water and dry in the shade.
Since the material is made out of paper, do not wring out the filter when removing water
from it.
[Replacement]
1. Remove the tabs on the filter frame and replace with a new filter.
• Dispose of the old filter as flammable waste.
List of Functions
173
Instruction
SiEBE12-625
NOTE
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
To order Titanium Apatite Photocatalytic Air-Purifying filter contact to the service shop there you bought the air conditioner.
Dispose of old filters as burnable waste.
Item
Titanium Apatite Photocatalytic Air-Purifying Filter.
(with frame) 1 set
Titanium Apatite Photocatalytic Air-Purifying Filter.
(without frame) 1 set
Part No.
KAF952B41
KAF952B42
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
FDK(X)S 25/35 C
174
List of Functions
SiEBE12-625
CAUTION
Instruction
•
•
Only a qualified service person is allowed to perform maintenance.
Before cleaning, be sure to stop the operation and turn the breaker OFF.
„ Cleaning the air filter
5. Remove the air filter.
• Rear suction
Pull the bottom side of the air filter backwards, over the 3 bends.
• Bottom suction
Pull the filter over the 3 bends situated at the backside of the unit.
6. Cleaning the air filter.
Remove dust from the air filter using a vacuum cleaner
and gently rinse them in cool water. Do not use
detergent or hot water to avoid filter shrinking or
deformation. After cleaning dry them in the shade.
7. Replacing the air filter.
• Rear suction
Hook the filter behind the flap situated at the top of the unit and push the other side gently over
the 3 bends.
• Bottom suction
Hook the filter behind the flap situated at the middle of the unit and push the other side gently
over the 3 bends.
Main unit
Force
Filter
Attach the filter to the
main unit while
pushing down on the
tabs
Force
In case of back side
List of Functions
In case of bottom side
175
Instruction
SiEBE12-625
„ Cleaning the drain pan
•
•
Clean the drain pan periodically, or drain piping may be clogged with dust and may result in
water leakage.
Ask your DAIKIN dealer to clean them.
Prepare a cover locally to prevent any dust in the air around the indoor unit from getting in the
drain pan, if there is a great deal of dust present.
CAUTION
•
•
•
•
•
•
•
Do not operate the air conditioner without filters, this to avoid dust accummulation inside the unit.
Do not remove the air filter except when cleaning;
Unnecessary handling meay damage the filter.
Do not use gasoline, benzene, thinner, polishing powder, liquid insecticide, it may cause discoloring or warping.
Do not let the indoor unit get wet. It may cause an electric shock or a fire.
Operation with dusty air filters lowers the cooling and heating capacidy and wastes energy.
The suction grille is option.
do not use water or air of 50°C or higher for cleaning air filters and outside panels.
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
176
List of Functions
SiEBE12-625
Instruction
FDK(X)S 50/60 C, FDK(X)S 25/35 E
CAUTION
•
•
Only a qualified service person is allowed to perform maintenance.
Before cleaning, be sure to stop the operation and turn the breaker OFF.
„ Cleaning the air filter
5. Remove the air filter.
• Rear suction
Pull the bottom side of the air filter backwards, over the bends. (2 bends for 25/35 type, 3 bends
for 50/60 type)
• Bottom suction
Pull the filter over the bends (2 bends for 25/35 type, 3 bends for 50/60 type) situated at the
backside of the unit.
6. Cleaning the air filter.
Remove dust from the air filter using a vacuum cleaner
and gently rinse them in cool water. Do not use
detergent or hot water to avoid filter shrinking or
deformation. After cleaning dry them in the shade.
7. Replacing the air filter.
• Rear suction
Hook the filter behind the flap situated at the top of the unit and push the other side gently over
the bends. (2 bends for 25/35 type, 3 bends for 50/60 type)
• Bottom suction
Hook the filter behind the flap situated at the middle of the unit and push the other side gently
over the bends. (2 bends for 25/35 type, 3 bends for 50/60 type)
Main unit
Main unit
Force
Force
Filter
Filter Force
Force
In case
of of
back
side
In case
back
side
List of Functions
Attach the filter to the
main unit while
Attach the
filteron
to the
the
pushing
down
main unit while
bends. (2 bends for
pushing down on the
25/35 type, 3 bends for
tabs
50/60 type)
In
bottom side
side
In case
case of bottom
177
Instruction
SiEBE12-625
„ Cleaning the drain pan
•
•
Clean the drain pan periodically, or drain piping may be clogged with dust and may result in
water leakage.
Ask your DAIKIN dealer to clean them.
Prepare a cover locally to prevent any dust in the air around the indoor unit from getting in the
drain pan, if there is a great deal of dust present.
CAUTION
•
•
•
•
•
•
•
•
Do not operate the air conditioner without filters, this to avoid dust accummulation inside the unit.
Do not remove the air filter except when cleaning;
Unnecessary handling may damage the filter.
Do not use gasoline, benzene, thinner, polishing powder, liquid insecticide, it may cause discoloring or warping.
Do not let the indoor unit get wet. It may cause an electric shock or a fire.
Operation with dusty air filters lowers the cooling and heating capacidy and wastes energy.
The suction grille is option.
Do not use water or air of 50°C or higher for cleaning air filters and outside panels.
Ask your DAIKIN dealer how to clean it.
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. Clean the air filters and set them again.
3. Take out batteries from the remote control.
4. Turn OFF the breaker for the room air conditioner.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
178
List of Functions
SiEBE12-625
Instruction
FLK(X)S 25/35/50/60 B
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Hold the panel by the tabs on the two sides and
lift it until it stops.
2. Clean the front panel
• Wipe it with a soft cloth soaked in water.
• Only neutral detergent may be used.
• In case of washing the panel with water, dry it with
cloth, dry it up in the shade after washing.
3. Attach the front panel
• Push the panel at the 5 points indicated by .
• Operation without air filters may result in troubles as
dust will accumulate inside the indoor unit.
CAUTION
•
•
•
•
•
Don’t touch the metal parts of the indoor unit. If you touch those parts, this may cause an injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the panel securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
179
Instruction
SiEBE12-625
Filters
1. Open the front panel.
2. Pull out the air filters..
• Push a little upwards the tab at the center of each
air filter, then pull it down.
3. Take off the air-purifying filter, photocatalytic
deodorizing filter.
• Hold the recessed parts of the frame and unhook
the four claws.
4. Clean or replace each filter.
See figure.
Air purifying filter
or Phototcatalytic
deodorizing filter
5. Set the air filter, air purifying filter and
photocatalytic deodorizing filter as they were and
close the front panel.
• Insert claws of the filters into slots of the front
panel.
• Push the panel at the 5 points.
„ Air Filter
1. Wash the air filters with water or clean them with vacuum
cleaner.
• If the dust does not come of easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Air-purifying Filter (green)
(Replace approximately once every 3 months.)
1. Detach the filter element and attach a new one.
• Insert with the green side up
• It is recommended to replace the air purifying filter every three
months.
„ Photocatalytic Deodorizing Filter (gray)
[Maintenance]
1. Dry the photocatalytic deodorizing filter in the sun.
• After removing the dust with a vacuum cleaner, place the filter in the sun for approximately
6 hours.
Bij drying the photocatalytic deodorizing filter in the sun, its deodorizing and antibacterial
capabilities are regenerated
• Because the filter material is paper, it can not be cleaned with water.
• It is recomended dry the filter once every 6 months.
[Replacement]
1. Detach the filter element and attach a new one.
180
List of Functions
SiEBE12-625
Instruction
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote control.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
NOTE
•
•
•
•
•
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
The air purifying filter and Photocatalytic deodorizing filter cannot be reused, even if washed.
In principle, there is no need to replace the photocatalytic deodorizing filter. Remove the dust periodically with a vacuum
cleaner; however, it is recommended to replace the filter in the following cases.
(1) The paper material is torn or broken during cleaning.
(2) The filter has become extremely dirty after long use.
To order air purifying filter with Photocatalytic deodorizing function contact to the service shop where you bought the air
conditioner.
Dispose of old air filters as non-burnable and Photocatalytic deodorizing filters as burnable waste.
Item
Photocatalytic deodorizing filter (with frame)
Photocatalytic deodorizing filter (without frame)
Air purifying filter (with frame)
Air purifying filter (without frame)
List of Functions
Part No.
KAZ917B41
KAZ917B42
KAF925B41
KAF925B42
181
Instruction
SiEBE12-625
FVK(X)S 25/35/50 B
CAUTION
Before cleaning, be sure to stop the operation and turn the breaker OFF.
Units
„ Indoor unit, Outdoor unit and Remote control
1. Wipe them with dry soft cloth.
„ Front panel
1. Open the front panel.
• Press the two
places on the left and right of
the front panel.
2. Remove the front panel.
• Remove the chain.
• Allowing the front panel to fall forward will enable
you to remove it.
Chain
3. Clean the front panel.
• Wipe softly with a damp cloth;
• Only neutral detergent may be used.
• In case of washing the front panel with water, dry
it with cloth, dry it up in the shade after washing.
4. Attach the front panel.
• Insert the front panel into the grooves of the unit
(3 places).
• Attach the chain to the right, inner-side of the
front panel.
• Close the panel slowly.
Place front panel in grooves.
CAUTION
•
•
•
•
•
•
182
Hold the front grille firmly so that it does not fall.
Do not touch the metal parts on the inside of the indoor unit, as it may result in injury.
When removing or attaching the front panel, use a robust and stable stool and watch your steps carefully.
When removing or attaching the front panel, support the panel securely with hand to prevent it from falling.
For cleaning, do not use hot water above 40 °C, benzine, gasoline, thinner, nor other volatile oils, polishing compound,
scrubbing brushes, nor other hand stuff.
After cleaning, make sure that the front panel is securely fixed.
List of Functions
SiEBE12-625
Instruction
Filters
1. Open the front panel.
2. Remove the air filter.
• Press the claws on the right and left of the air
filter down slchtly, then pull upward..
3. Take off the air-purifying filter, photocatalytic
deodorizing filter.
• Hold the tabs of the frame and remove the claws
in 4 places.
Air purifying filter
or photocatalytic
deodorizing filter
4. Clean or replace each filter.
See figure.
Air filter
5. Set the air filter, air purifying filter and
photocatalytic deodorizing filter as they were and
close the front panel.
• Operation without air filters may result in troubles
as dust will accumulate inside the indoor unit.
„ Air Filter
1. Wash the air filters with water or clean them with vacuum
cleaner.
• If the dust does not come off easily, wash them with neutral
detergent thinned with lukewarm water, then dry them up in the
shade.
• It is recommended to clean the air filters every two weeks.
„ Air-purifying Filter (green)
(replace approximately once every 3 months.)
1. Detach the filter element and attach a new one.
• Insert with the green side up
• It is recommended to replace the air purifying filter every three
months.
„ Photocatalytic Deodorizing Filter (gray)
[Maintenance]
1. Dry the photocatalytic deodorizing filter in the sun.
• After removing the dust with a vacuum cleaner, place the filter in the sun for approximately
6 hours.
Bij drying the photocatalytic deodorizing filter in the sun, its deodorizing and antibacterial
capabilities are regenerated
• Because the filter material is paper, it can not be cleaned with water.
• It is recomended dry the filter once every 6 months.
[Replacement]
1. Detach the filter element and attach a new one.
List of Functions
183
Instruction
SiEBE12-625
Check
Check that the base, stand and other fittings of the outdoor unit are not decayed or corroded.
Check that nothing blocks the air inlets and the outlets of the indoor unit and the outdoor unit.
Check that the drain comes smoothly out of the drain hose during COOL or DRY operation.
• If no drain water is seen, water may be leaking from the indoor unit. Stop operation and consult
the service shop if this is the case.
„ Before a long idle period
1. Operate the “FAN only” for several hours on a fine day to dry out the inside.
• Press “MODE” button and select “FAN” operation.
• Press “ON/OFF” button and start operation.
2. After operation stops, turn off the breaker for the room air conditioner.
3. Clean the air filters and set them again.
4. Take out batteries from the remote controller.
• When a multi outdoor unit is connected, make sure the heating operation is not used at the
other room before you use the fan operation.
NOTE
•
•
•
•
•
•
Operation with dusty air filters lowers the cooling (heating) capacity and wastes energy.
Air is also prevented from flowing smoothly through the unit creating a noise.
Operation with dirty filters :
(1) cannot deodorize the air.(2) cannot clean the air.
(3) results in poor heating or cooling.(4) may cause odour.
The air purifying filter and Photocatalytic deodorizing filter cannot be reused, even if washed.
In principle, there is no need to replace the photocatalytic deodorizing filter. Remove the dust periodically with a vacuum
cleaner. However, it is recommended to replace the filter in the following cases.
(1) The paper material is torn or broken during cleaning.
(2) The filter has become extremely dirty after long use.
To order air purifying filter or Photocatalytic deodorizing filter, contact to the service shop where you bought the air
conditioner.
Dispose of old filters as non-burnable waste and Photocatalytic deodorizing filters as burnable waste.
Item
Photocatalytic deodorizing filter (with frame)
Photocatalytic deodorizing filter (without frame)
Air purifying filter (with frame)
Air purifying filter (without frame)
184
Part No.
KAZ917B41
KAZ917B42
KAF925B41
KAF925B42
List of Functions
SiEBE12-625
Instruction
2.15 Troubleshooting
These cases are not troubles.
The following cases are not air conditioner troubles but have some reasons. You may just continue
using it.
Case
Explanation
•
Operation does not start soon.
• When ON/OFF button was pressed
soon after operation was stopped.
• When the mode was reselected.
Hot air does not flow out soon after •
the start of heating operation.
The heating operation stops
suddenly and a flowing sound is
heard.
The outdoor unit emits water or
steam.
•
This is to protect the air conditioner.
You should wait for about 3 minutes.
The air conditioner is warming up. You should wait for
1 to 4 minutes.
(The system is designed to start discharging air only
after it has reached a certain temperature.)
The system is taking away the frost on the outdoor unit.
You should wait for about 3 to 8 minutes.
„ In HEAT mode
• The frost on the outdoor unit melts into water or
steam when the air conditioner is in defrost
operation.
„ In COOL or DRY mode
• Moisture in the air condenses into water on the cool
surface of outdoor unit piping and drips.
Mists come out of the indoor unit.
„ This happens when the air in the room is cooled into mist
by the cold air flow during cooling operation.
The indoor unit gives out odour.
„ This happens when smells of the room, furniture, or
cigarettes are absorbed into the unit and discharged with
the air flow.
(If this happens, we recommend you to have the indoor
unit washed by a technician. Consult the service shop
where you bought the air conditioner.)
The outdoor fan rotates while the air „ After operation is stopped:
conditioner is not in operation.
• The outdoor fan continues rotating for another 60
seconds for system protection.
„ While the air conditioner is not in operation:
• When the outdoor temperature is very high, the out
door fan starts rotating for system protection.
The operation stopped suddenly.
„ For system protection, the air conditioner may stop
(OPERATION lamp is on)
operating on a sudden large voltage fluctuation.
It automatically resumes operation in about 3 minutes.
List of Functions
185
Instruction
SiEBE12-625
Check again.
Please check again before calling a repair person.
Case
The air conditioner does not
operate.
(OPERATION lamp is off)
Cooling (Heating) effect is poor.
Check
•
•
•
•
•
•
•
•
•
Operation stops suddenly.
(OPERATION lamp flashes.)
•
•
•
•
An abnormal functioning happens
during operation.
186
•
Hasn’t a breaker turned OFF or a fuse blown?
Isn’t it a power failure?
Are batteries set in the remote control?
Is the timer setting correct?
Are the air filters clean?
Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Is the temperature setting appropriate?
Are the windows and doors closed?
Are the air flow rate and the air direction set
appropriately?
Is the unit set to the INTELLIGENT EYE mode?
Are the air filters clean?
Is there anything to block the air inlet or the outlet of the
indoor and the outdoor units?
Clean the air filters or take all obstacles away and turn
the breaker OFF. Then turn it ON again and try
operating the air conditioner with the remote control. If
the lamp still flashes, call the service shop where you
bought the air conditioner.
Are operation modes all the same for indoor units
connected to outdoor units in the multi system?
If not, set all indoor units to the same operation mode
and confirm that the lamps flash.
Moreover, when the operation mode is in “AUTO”, set all
indoor unit operation modes to “COOL” or “HEAT” for a
moment and check again that the lamps are normal.
If the lamps stop flashing after the above steps, there is
no malfunction.
The air conditioner may malfunction with lightening or
radio waves. Turn the breaker OFF, turn it ON again and
try operating the air conditioner with the remote control.
List of Functions
SiEBE12-625
Instruction
Call the service shop immediately.
WARNING
„ When an abnormality (such as a burning smell) occurs, stop operation and turn the breaker OFF.
Continued operation in an abnormal condition may result in troubles, electric shocks or fire.
Consult the service shop where you bought the air conditioner.
„ Do not attempt to repair or modify the air conditioner by yourself.
Incorrect work may result in electric shocks or fire.
Consult the service shop where you bought the air conditioner.
If one of the following symptoms takes place, call the service shop immediately.
„ The power cord is abnormally hot or damaged.
„ An abnormal sound is heard during operation.
„ The safety breaker, a fuse, or the earth leakage
breaker cuts off the operation frequently.
„ A switch or a button often fails to work properly.
„ There is a burning smell.
„ Water leaks from the indoor unit.
Turn the breaker
OFF and call the
service shop.
„ After a power failure
„ Lightening
The air conditioner automatically resumes
If lightening may strike the neighbouring area,
operation in about 3 minutes. You should just
stop operation and turn the breaker OFF for
wait for a while.
system protection.
Disposal requirements
Your air conditioning product is marked with this symbol. This means that electrical
and electronic products shall not be mixed with unsorted household waste.
Do not to try to dismantle the system yourself: the sismantling of the air conditioning
system, treatment of the refrigerant, of oil and of other parts must be done by a
qualified installer in accordance with relevant local and national legislation.
Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. Bij
ensuring this product is disposed of correctly, you will help to prevent potential negative consequences
for the environment and human health. Please contact the installer or local authority for more
information.
Batteries must be removed from the remote controller and disposed of separately in accordance with
relevant local and national legislation.
We recommend periodical maintenance
In certain operating conditions, the inside of the air conditioner may get foul after several seasons of
use, resulting in poor performance. It is recommended to have periodical maintenance by a specialist
aside from regular cleaning by the user. For specialist maintenance, contact the service shop where
you bought the air conditioner.
The maintenance cost must be born by the user.
List of Functions
187
Instruction
SiEBE12-625
Fault diagnosis
FAULT DIAGNOSIS BY REMOTE CONTROL
In the ARC433A series, the temperature display sections on the main unit indicate corresponding
codes.
1. When the TIMER CANCEL button is held down for 5 seconds, a “ ” indication
flashes on the temperature display section.
ON
C
HOME LEAVE
ON/OFF
POWERFUL
TEMP
MODE
SILENT
FAN
ON
SWING
SENSOR
CANCEL
OFF
TIMER CANCEL button
It cancels the timer setting.
TIMER
2. Press TIMER CANCEL button repeatedly until a continuous beeep is produced.
• The code indication changes as shown below, and notifies with a long beep.
SYSTEM
INDOOR
UNIT
OUTDOOR
UNIT
CODE
00
U0
U2
U4
A1
A5
A6
C4
C9
EA
E5
E6
E7
E8
F3
F6
H6
H8
H9
J3
J6
L4
L5
P4
MEANING
NORMAL
REFRIGERANT SHORTAGE
DROP VOLTAGE OR MAIN CIRCUIT OVERVOLTAGE
FAILURE OF TRANSMISSION (BETWEEN INDOOR UNIT AND OUTDOOR UNIT)
INDOOR PCB DEFECTIVENESS
HIGH PRESSURE CONTROL OR FREEZE-UP PROTECTION
FAN MOTOR FAULT
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
FAULTY SUCTION AIR TEMPERATURE SENSOR
COOLING-HEATING SWITCHING ERROR
OL STARTED
FAULTY COMPRESSED START UP
DC FAN MOTOR FAULT
OPERATION HALT DUE TOT DETECTION OF INPUT OVER CURRENT
HIGH TEMPERATURE DICHARGE PIPE CONTROL
HIGH PRESSURE CONTROL (IN COOLING)
OPERATION HALT DUE TO DETECTION OF INPUT OVER CURRENT
CT ABNORMALITY
FAULTY SUCTION AIR TEMPERATURE SENSOR
FAULTY DISCHARGE PIPE TEMPERATURE SENSOR
FAULTY HEAT EXCHANGER TEMPERATURE SENSOR
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
OUTPUT OVERCURRENT
FAULTY INVERTER CIRCUIT HEATSINK TEMPERATURE SENSOR
NOTE
1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To cancel the code display, hold the TIMER CANCEL button down for 5 seconds. The code display also cancel itself if the
button is not pressed for 1 minute.
188
List of Functions
SiEBE12-625
Instruction
LED ON OUTDOOR UNIT PCB
3MXS, 3MKS, 4MXS, 4MKS series
GREEN
RED
MICROCOMPUTER
NORMAL
MALFUNCTION
DETECTION
LED1 LED2 LED3
LED-A
LED4
DIAGNOSIS
NORMAL -> CHECK INDOOR UNIT
HIGH PRESSURE PROTECTOR WORKED OR FREEZE-UP IN OPERATING UNIT OR STAND-BY UNIT
* OVERLOAD RELAY WORKED OR HIGH DISCHARGE PIPE TEMPERATURE
FAULTY COMPRESSOR START
INPUT OVERCURRENT
* THERMISTOR OR CT ABNORMALITY
HIGH TEMPERATURE SWITCHBOX
HIGH TEMPERATURE AT INVERTER CIRCUIT HEATSINK
* OUTPUT OVERCURRENT
* REFRIGERANT SHORTAGE
LOW VOLTAGE TOT MAIN CIRCUIT OR MOMENTARY VOLTAGE
LOSS
REVERSING SOLENOID VALVE SWITCHING FAILURE
FAN MOTOR FAULT
-
-
-
-
[NOTE 1]
-
-
-
-
POWER SUPPLY FAULT OR [NOTE 2]
GREEN
NORMALLY
FLASHING
RED
NORMALLY OFF
ON
FLASHING
OFF
-
IRRELEVANT
GREEN
MICROCOMPUTER
NORMAL
LED-A
DIAGNOSIS
NORMAL-> CHECK INDOOR UNIT
[NOTE1]
POWER SUPPLY FAULT OR [NOTE2]
GREEN
NORMALLY
FLASHING
RED
NORMALLY OFF
ON
FLASHING
OFF
NOTES
1 Turn the power off and then on again. If the LED display recurs, the outdoor unit PCB is faulty.
2 Diagnosis marked
* Do not apply to some cases. For details, refer to the service guide.
List of Functions
189
Instruction
190
SiEBE12-625
List of Functions
SiEBE12-625
Part 6
Service Diagnosis
1. Caution for Diagnosis..........................................................................192
1.1 Troubleshooting with Operation Lamp .................................................192
2. Problem Symptoms and Measures .....................................................194
3. Service Check Function ......................................................................195
4. Code Indication on the Remote Controller ..........................................198
4.1 Error Codes and Description of Fault ...................................................198
5. Troubleshooting ..................................................................................199
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
5.15
5.16
5.17
5.18
5.19
5.20
5.21
5.22
5.23
5.24
5.25
5.26
5.27
Indoor Units ..........................................................................................199
Outdoor Units .......................................................................................200
Indoor Unit PCB Abnormality ...............................................................201
Freeze-up Protection Control or High Pressure Control.......................202
Fan Motor or Related Abnormality .......................................................204
Thermistor or Related Abnormality (Indoor Unit)..................................207
Shutter Drive Motor / Shutter Limit Switch Abnormality .......................208
Front Panel Open / Close Fault............................................................209
Signal Transmission Error (between Indoor and Outdoor Units)..........210
Unspecified Voltage (between Indoor and Outdoor Units) ...................211
Freeze-up Protection Control ...............................................................212
OL Activation (Compressor Overload) .................................................214
Compressor Lock .................................................................................215
DC Fan Lock ........................................................................................216
Input Over Current Detection ...............................................................217
Four Way Valve Abnormality................................................................219
Discharge Pipe Temperature Control...................................................221
High Pressure Control in Cooling .........................................................222
Position Sensor Abnormality ................................................................224
CT or Related Abnormality ...................................................................225
Thermistor or Related Abnormality (Outdoor Unit)...............................227
Electrical Box Temperature Rise..........................................................229
Radiation Fin Temperature Rise ..........................................................231
Output Over Current Detection.............................................................233
Insufficient Gas.....................................................................................235
Low-voltage Detection..........................................................................237
Anti-icing Function in Other Rooms / Unspecified Voltage
(between Indoor and Outdoor Units) ....................................................238
6. Check ..................................................................................................239
6.1 How to Check .......................................................................................239
Service Diagnosis
191
Caution for Diagnosis
SiEBE12-625
1. Caution for Diagnosis
1.1
Troubleshooting with Operation Lamp
The operation lamp flashes when any of the following errors is detected.
1. When a protection device of the indoor or outdoor unit is activated or when the thermistor
malfunctions, disabling equipment operation.
2. When a signal transmission error occurs between the indoor and outdoor units.
In either case, conduct the diagnostic procedure described in the following pages.
Location of
Operation Lamp
In case of
FTK(X)S 20/25/35/50 D Series
In case of
FTK(X)S 20/25/35 C Series
OPERATION lamp (green)
Indicator lamps
ON
OFF
ON/OFF
Operation lamp (green)
(R4298)
(R4297)
In case of
FTK(X)S 50/60/71 E Series
FTK(X)S 71 B Series
In case of
FTXG 25/35 E, CTXG 50 E Series
Air outlet
Indicator lamps
Indicator lamps
Operation lamp (green)
ON
OFF
Operation lamp (green)
TIMER lamp (yellow)
TIMER lamp (yellow)
ON/OFF switch
INTELLIGENT EYE lamp (green)
ON/OFF
ON/OFF switch
HOME LEAVE lamp (red)
(R2837)
In case of
FDK(X)S 25/35/50/60 C Series
FDK(X)S 25/35 E Series
(R5072)
In case of
FVK(X)S 25/35/50 B Series
OPERATION lamp (green)
ON
OFF
OPERATION lamp (green)
(Q0342)
(Q0340)
192
Service Diagnosis
SiEBE12-625
Caution for Diagnosis
In case of
FLK(X)S 25/35/50/60 B Series
OPERATION lamp (green)
(Q0341)
Caution:
Operation stops suddenly. (Operation lamp blinks.)
Cause of above trouble could be "Operation mode conflict".
Check followings;
Are the operation modes all the same for indoor units connected to Multi system outdoor unit?
If not set all indoor units to the same operation mode and confirm that the operation lamp is not
blinking.
Moreover, when the operation mode is in "Auto", set all indoor unit operation mode to "Cool" or
"Heat" and check again if the operation lamp is normal.
If the lamp stops blinking after the above steps, there is no malfunction.
HOperation stops and operation lamp blinks only for indoor unit which the different operation
mode is set later. (The first set operation mode has priority.)
Troubleshooting
with the LED
Indication
Outdoor Unit
LED A
LED 1
LED 2
LED 3
LED 4
There are green and red LEDs on the PCB. The flashing green LED indicates normal equipment
condition, and the OFF condition of the red LED indicates normal equipment condition.
(Troubleshooting with the green LED)
The LED A (green) of the outdoor unit indicate microcomputer operation condition.
Even after the error is cancelled and the equipment operates in normal condition, the LED
indication remains.
Service Diagnosis
193
Problem Symptoms and Measures
SiEBE12-625
2. Problem Symptoms and Measures
Problem Symptom
Check Item
None of the units operates. Check the power supply.
Check the type of the indoor units.
Check the outdoor air temperature.
Diagnosis with indoor unit LED
indication
Diagnosis with outdoor unit LED
indication
Check the remote controller
addresses.
Operation sometimes
stops.
Check the power supply.
Check the outdoor air temperature.
Some indoor units do not
operate.
Equipment operates but
does not cool, or does not
heat (only for heat pump
model).
Large operating noise and
vibrations
194
Diagnosis with indoor unit LED
indication
Diagnosis with outdoor unit LED
indication
Check the type of the indoor units.
Details of Measure
Check to make sure that the rated voltage is
supplied.
Check to make sure that the indoor unit type is
compatible with the outdoor unit.
Heating operation cannot be used when the
outdoor air temperature is 21°C or higher (only
for heat pump model), and cooling operation
cannot be used when the outdoor air
temperature is below –10 °C
—
Page
No.
to be
referred
—
—
—
199
—
200
Check to make sure that address settings for
the remote controller and indoor unit are
correct.
A power failure of 2 to 10 cycles can stop air
conditioner operation. (Operation lamp OFF)
Heating operation cannot be used when the
outdoor air temperature is 21°C or higher (only
for heat pump model), and cooling operation
cannot be used when the outdoor air
temperature is below –10°C
—
—
199
—
200
Check to make sure that the indoor unit type is
compatible with the outdoor unit.
—
—
Diagnosis with indoor unit LED
indication
Diagnosis with outdoor unit LED
—
indication
Check for wiring and piping errors in Conduct the wiring/piping error check described
the indoor and outdoor units
on the product diagnosis nameplate.
connection wires and pipes.
Check for thermistor detection errors. Check to make sure that the main unit’s
thermistor has not dismounted from the pipe
holder.
Check for faulty operation of the
Set the units to cooling operation, and compare
electronic expansion valve.
the temperatures of the liquid side connection
pipes of the connection section among rooms to
check the opening and closing operation of the
electronic expansion valves of the individual
units.
Diagnosis with indoor unit LED
—
indication
Diagnosis with outdoor unit LED
—
indication
Diagnosis by service port pressure
Check for insufficient gas.
and operating current
Check the output voltage of the
—
power transistor.
Check the power transistor.
—
Check the installation condition.
Check to make sure that the required spaces
for installation (specified in the Engineering
Data book, etc.) are provided.
—
—
199
200
—
—
—
199
200
245
246
—
—
Service Diagnosis
SiEBE12-625
Service Check Function
3. Service Check Function
In the ARC433A series remote controller, the temperature display sections on the main unit
indicate corresponding codes.
Check Method 1
1. When the timer cancel button is held down for 5 seconds, a “00” indication flashes on the
temperature display section.
ECONO
POWERFUL
ON/OFF
TEMP
MODE
FAN
SWING
SILENT COMFORT SENSOR
ON
CANCEL
TIMER CANCEL button
It cancels the timer setting.
OFF
TIMER
<ARC433A50, 43>
(R4271)
2. Press the timer cancel button repeatedly until a continuous beep is produced.
„ The code indication changes in the sequence shown below, and notifies with a long beep.
No.
1
2
3
4
5
6
7
8
9
10
11
Code
00
U4
F3
E6
L5
A6
E5
F6
C9
U0
E7
No.
12
13
14
15
16
17
18
19
20
21
22
Code
C7
H8
J3
A3
A1
C4
C5
H9
J6
UA
A5
No.
23
24
25
26
27
28
29
30
31
32
33
Code
H0
E1
P4
L3
L4
H6
H7
U2
UH
EA
AH
Code
F6
C7
A3
H8
H9
C9
C4
C5
J3
J6
E5
No.
23
24
25
26
27
28
29
30
31
32
33
Code
A1
E1
UA
UH
P4
L3
L4
H7
U2
EA
AH
<In case of ARC433A41, 43, 50>
No.
1
2
3
4
5
6
7
8
9
10
11
Note:
Service Diagnosis
Code
00
U4
L5
E6
H6
H0
A6
E7
U0
F3
A5
No.
12
13
14
15
16
17
18
19
20
21
22
1. A short beep and two consecutive beeps indicate non-corresponding codes.
2. To cancel the code display, hold the timer cancel button down for 5 seconds. The code
display also cancels itself if the button is not pressed for 1 minute.
195
Service Check Function
SiEBE12-625
Check Method 2
1. Enter the diagnosis mode.
Press the 3 buttons (TEMPs,TEMPt, MODE) simultaneously.
(R4272)
The digit of the number of tens blinks.
HTry again from the start when the digit does not blink.
(R4273)
2. Press the TEMP button.
Press TEMPs or TEMPt and change the digit until you hear the sound of “beep” or “pi pi”.
(R4274)
3. Diagnose by the sound.
H“pi” : The number of tens does not accord with the error code.
H“pi pi” : The number of tens accords with the error code.
H“beep” : The both numbers of tens and units accord with the error code. (→ See 7.)
4. Enter the diagnosis mode again.
Press the MODE button.
(R4275)
The digit of the number of units blinks.
(R4276)
196
Service Diagnosis
SiEBE12-625
Service Check Function
5. Press the TEMP button.
Press TEMPs or TEMPt and change the digit until you hear the sound of “beep”.
(R4277)
6. Diagnose by the sound.
H“pi” : The both numbers of tens and units do not accord with the error code.
H“pi pi” : The number of tens accords with the error code.
H“beep” : The both numbers of tens and units accord with the error code.
7. Determine the error code.
The digits indicated when you hear the “beep” sound are error code.
(Error codes and description → Refer to page 198.)
8. Exit from the diagnosis mode.
Press the MODE button.
(R4278)
Service Diagnosis
197
Code Indication on the Remote Controller
SiEBE12-625
4. Code Indication on the Remote Controller
4.1
Error Codes and Description of Fault
Code Indication Description of Problem
System
Indoor
Unit
Outdoor
Unit
198
00
U0
U2
U4
UA
UH
A1
A5
A6
C4
Normal
C7
Shutter drive motor / shutter limit switch abnormality
Front panel open / close fault
C9
A5
E5
E6
E7
E8
EA
F3
F6
H6
H8
H9
J3
J6
J8
J9
L3
L4
L5
P4
Room temperature thermistor abnormality
Insufficient gas
Low-voltage detection
Signal transmission error (between indoor and outdoor units)
Unspecified voltage (between indoor and outdoor units)
Anti-icing function in other rooms
Indoor unit PCB abnormality
Freeze-up protection function or high pressure control
Fan motor or related abnormality
Heat exchanger temperature thermistor abnormality
Freeze-up protection control
OL activation (compressor overloaded)
Compressor lock
DC fan lock
Input over current detection
Four way valve abnormality
Discharge pipe temperature control
High pressure control in cooling
Position sensor abnormality
CT or related abnormality
Outdoor air thermistor or related abnormality
Discharge pipe thermistor or related abnormality
Heat exchanger thermistor or related abnormality
Liquid pipe thermistor or related abnormality
Gas pipe thermistor or related abnormality
Electrical box temperature rise
Radiation fin temperature rise
Output over current detection
Radiation fin thermistor or related abnormality
Service Diagnosis
SiEBE12-625
Troubleshooting
5. Troubleshooting
5.1
Indoor Units
- : Not used for troubleshooting
∗ : Varies depending on the cases.
Indication on the
remote controller
00
A1
A5
Description of the Fault
Indoor unit in normal condition (Conduct a diagnosis of the outdoor unit.)
Details of fault
(Refer to the
indicated page.)
—
Indoor unit PCB abnormality
201
Freeze-up protection control or high pressure control (heat pump model only)
202
AC motor (Wall : 20~35 C series, Duct, Floor / Ceiling)
DC motor (Wall : 20~35 D series and 25~71 E series, Floor)
204
205
A6
Fan motor or related
abnormality
C4
Heat exchanger thermistor or related abnormality
207
C7
Shutter drive motor / shutter limit switch abnormality (Floor standing type)
Front panel open / close fault (FTXG-E series, CTXG-E series)
208
209
C9
U4
UA
Room temperature thermistor abnormality
207
Signal transmission error (between indoor and outdoor units)
210
Unspecified voltage (between indoor and outdoor units)
211
Service Diagnosis
199
Troubleshooting
5.2
SiEBE12-625
Outdoor Units
4: ON, 1: OFF, 5: Blinks
Green : Flashes when in normal condition
Red : OFF in normal condition
- : Not used for troubleshooting
∗ : Varies depending on the cases.
Outdoor Unit LED Indication
Green
Red
A
1
2
3
4
5
5
5
5
5
5
5
5
5
5
5
5
3
3
4
4
4
3
4
3
4
4
4
4
3
3
3
3
3
4
4
4
3
3
3
4
3
4
3
4
4
4
4
3
3
4
4
3
Indication on
the remote
controller
3 00
4
4
4
3
3
4
4
3
3
4
3
UA
UH
(U0)
U2
A5
(E5)
(E6)
E7
E8
EA
F3
F6
H6
H9
J3
J6
J8
J9
P4
H8
L3
L4
5
5
5
4
4
3
4
4
3
3
3
3
3
4
4
5
3
3
4
3 L5
Note:
200
Description of The Fault
Reference
Page
Outdoor unit in normal condition
(Conduct a diagnosis of the indoor unit.)
Unspecified voltage (between indoor and outdoor units)
238
Anti-icing function in other rooms
238
Insufficient gas
235
Low-voltage detection
237
Freeze-up protection control
212
OL activation (compressor overload)
214
Compressor lock
215
DC fan lock
216
Input over current detection
217
Four way valve abnormality
219
Discharge pipe temperature control
221
High pressure control in cooling
222
Position sensor abnormality
224
Outdoor air thermistor or related abnormality
227
Discharge pipe thermistor or related abnormality
227
Heat exchanger thermistor or related abnormality
227
Liquid pipe thermistor or related abnormality
227
Gas pipe thermistor or related abnormality
227
Radiation fin thermistor or related abnormality
227
CT or related abnormality
225
Electrical box temperature rise
229
Radiation fin temperature rise
(Protection of driver overheating)
Output over current detection
231
—
233
1. The indications in the parenthesis ( ) in the remote controller display column are displayed
only when system-down occurs.
2. When a sensor error occurs, check the remote controller display to determine which sensor
is malfunctioning.
If the remote controller does not indicate the error type, conduct the following operation.
*Turn the power switch off and back on again. If the same LED indication appears again
immediately after the power is turned on, the fault is in the thermistor.
*If the above condition does not result, the fault is in the CT.
3. The indoor unit error indication may take the precedence in the remote controller display.
Service Diagnosis
SiEBE12-625
5.3
Troubleshooting
Indoor Unit PCB Abnormality
A1
Remote
Controller
Display
Method of
Malfunction
Detection
Evaluation of zero-cross detection of power supply by indoor unit.
Malfunction
Decision
Conditions
When there is no zero-cross detection in approximately 10 continuous seconds.
Supposed
Causes
„ Faulty indoor unit PCB
„ Faulty connector connection
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Connector connection check
(note).
Is it normal?
NO
Correct connections.
YES
Replace PCBs.
(R1400)
Note:
Connector Nos. vary depending on models.
Control connector
Model Type
Wall Mounted Type 20 / 25 / 35 class
Wall Mounted Type 50 / 60 / 71 class
Duct Connected Type
Floor / Ceiling Suspended Dual Type
Floor Standing Type
Service Diagnosis
Connector No.
Terminal strip~Control PCB
Terminal strip~Control PCB
Terminal strip~Control PCB
S37
Control PCB : S7, S201, S203
Power Supply PCB : S8, S202, S204
201
Troubleshooting
5.4
SiEBE12-625
Freeze-up Protection Control or High Pressure Control
Remote
Controller
Display
A5
Method of
Malfunction
Detection
„ High pressure control (heat pump model only)
During heating operations, the temperature detected by the indoor heat exchanger
thermistor is used for the high pressure control (stop, outdoor fan stop, etc.)
„ The freeze-up protection control (operation halt) is activated during cooling operation
according to the temperature detected by the indoor unit heat exchanger thermistor.
Malfunction
Decision
Conditions
„ High pressure control
During heating operations, the temperature detected by the indoor heat exchanger
thermistor is above 65°C
„ Freeze-up protection
When the indoor unit heat exchanger temperature is below 0°C during cooling operation.
Supposed
Causes
„
„
„
„
„
202
Operation halt due to clogged air filter of the indoor unit.
Operation halt due to dust accumulation on the indoor unit heat exchanger.
Operation halt due to short-circuit.
Detection error due to faulty indoor unit heat exchanger thermistor.
Detection error due to faulty indoor unit PCB.
Service Diagnosis
SiEBE12-625
Troubleshooting
Troubleshooting
Caution
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the air filter.
Is there any
short-circuit?
YES
Provide sufficient air passage.
NO
Check the intake air filter.
Is it very dirty?
YES
Clean the air filter.
NO
Check the dust accumulation on
the indoor unit heat exchanger.
Is it very dirty?
YES
Clean the heat exchanger.
NO
Check No. 06
Indoor unit heat exchanger
thermistor check
Does it conform to
the thermistor characteristic
chart?
NO
YES
Replace the indoor unit PCB.
Replace the thermistor
(replace the indoor unit PCB).
(R4695)
Note:
Service Diagnosis
If the outside temperature is below –10°C in the cooling mode, the system may get interrupted
with error A5 displayed. The system will be reset itself, but this stop will be put in the error history
memory.
203
Troubleshooting
5.5
SiEBE12-625
Fan Motor or Related Abnormality
5.5.1 AC Motor
Remote
Controller
Display
A6
Method of
Malfunction
Detection
The rotation speed detected by the Hall IC during fan motor operation is used to determine
abnormal fan motor operation.
Malfunction
Decision
Conditions
When the detected rotation speed does not reach the demanded rotation speed of the target
tap, and is less than 50% of the maximum fan motor rotation speed.
Supposed
Causes
„
„
„
„
„
Operation halt due to short circuit inside the fan motor winding.
Operation halt due to breaking of wire inside the fan motor.
Operation halt due to breaking of the fan motor lead wires.
Operation halt due to faulty capacitor of the fan motor.
Detection error due to faulty control PCB.
Troubleshooting
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Caution
Check No.16
Refer to P.248
Operate the fan.
Does it rotate?
YES
Check No. 16
Check Hall IC
NO
Rotate the fan by hand.
Is there an output?
NO
NO
YES
Does it rotate smoothly?
Replace the fan motor
Check the fan motor voltage.
YES
Check the fan motor voltage.
(immediately after re-start)
NO
Is it at the rated voltage?
∗
YES
NO
Is it at the rated voltage?
Check the capacitor's
conductivity
Is there conductivity?
Check No. 16NO
Check Hall IC
204
Replace control PCB.
Replace the fan motor.
Replace the control PCB.
urn off power switch before connect or disconnect connector,
YES
mage may be occurred.
YES
Replace the fan motor or control
PCB
YES
∗ Measure the voltage between
the red and black lead wires of
the fan motor, and check if the
maximum voltage reaches the
rated voltage.
Replace the capacitor.
(Replace the control PCB.)
Replace the fan motor.
(R3219)
Service Diagnosis
SiEBE12-625
Troubleshooting
5.5.2 DC Motor
Remote
Controller
Display
A6
Method of
Malfunction
Detection
The rotation speed detected by the Hall IC during fan motor operation is used to determine
abnormal fan motor operation.
Malfunction
Decision
Conditions
When the detected rotation speed does not reach the demanded rotation speed of the target
tap, and is less than 50% of the maximum fan motor rotation speed.
Supposed
Causes
„
„
„
„
„
Service Diagnosis
Operation halt due to short circuit inside the fan motor winding.
Operation halt due to breaking of wire inside the fan motor.
Operation halt due to breaking of the fan motor lead wires.
Operation halt due to faulty capacitor of the fan motor.
Detection error due to faulty indoor unit PCB (1).
205
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check No.01
Refer to P.239
Turn off power supply
and rotate fan by hand.
Check No.02
Refer to P.239
Does fan rotate
smoothly?
NO
Replace fan motor.
YES
Turn power ON and
operate fan.
Does it rotate?
Turn off power supply
NO and disconnect fan motor
connector, then turn
power ON.
YES
Check No.01
Check output of fan
motor connector
Is motor
power voltage
DC 200V
generated?
NO
Replace indoor
unit PCB (1) .
YES
Is motor
control power voltage
DC 15V
generated?
NO Check No.02
Check output of indoor
unit PCB (1)
YES
Turn off power supply and
disconnect fan motor
connector, then turn
power ON again.
Is motor control
power voltage DC 16V
generetad?
NO
Replace indoor
unit PCB (1) .
YES
Check No.01
Check output of fan
motor connector
Is rotation
number command
voltage DC 5V
generated?
Replace indoor
unit PCB (2) .
YES
NO
Check No.01
Check output of fan
motor connector
Stop fan motor.
Is rotation
NO
number command pulse
generated?
Check No.01
Check output of fan
motor connector
YES
Is rotation
number command pulse
generated?
YES
NO
Replace fan motor.
Note : Motor may
break when
the motor
connector is
disconnected
while
remaining
power supply.
Replace fan motor
and indoor PCB (2)
.
Replace indoor
unit PCB (2) .
Replace fan motor.
Replace indoor
unit PCB (2) .
(R1214)
206
Service Diagnosis
SiEBE12-625
5.6
Troubleshooting
Thermistor or Related Abnormality (Indoor Unit)
C4, C9
Remote
Controller
Display
Method of
Malfunction
Detection
The temperatures detected by the thermistors are used to determine thermistor errors.
Malfunction
Decision
Conditions
When the thermistor input is more than 4.96 V or less than 0.04 V during compressor
operation∗.
∗ (reference)
When above about 212°C (less than 120 ohms) or below about -50°C (more than 1,860 kohms).
Note:
Supposed
Causes
The values vary slightly in some models.
„ Faulty connector connection
„ Faulty thermistor
„ Faulty PCB
Troubleshooting
Caution
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the connector connection.
Is it normal?
NO
Correct the connection.
YES
Check No. 06
Thermistor resistance check
Is it normal?
NO
YES
Replace the thermistor.
(Replace the indoor unit PCB.)
Replace the indoor unit PCB.
(R4696)
C4 : Heat exchanger temperature thermistor
C9 : Room temperature thermistor
Service Diagnosis
207
Troubleshooting
5.7
SiEBE12-625
Shutter Drive Motor / Shutter Limit Switch Abnormality
Remote
Controller
Display
C7
Method of
Malfunction
Detection
The shutter open / close performance is detected by the limit switch attached on its structure. In
this way, the shutter drive motor and the shutter limit switch are checked for failure.
Malfunction
Decision
Conditions
When the shutter is open, the limit switch is closed.
Supposed
Causes
„
„
„
„
„
„
„
Shutter drive motor defective
Shutter limit switch defective
Shutter itself deformed (warped)
Shutter's sealing material too thick
Detection error by broken relay harness or disconnected connector
Detection error due to defective PCB (2)
Foreign substance in blow port
Troubleshooting
Caution
Check No.03
Refer to P.239
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn off the power.
Foreign substance in
the shutter structure?
YES
Remove such substance.
NO
Check No. 03
Check the limit switch continuity.
Limit switch on power?
NO
Replace the limit switch.
YES
Open the shutter and turn on the
power.
Shutter closed?
NO
YES
Shutter opening itself?
NO
Relay harness
broken or connector
disconnected?
NO
YES
YES Reconnect the connector or
replace the relay harness.
Replace the shutter drive
motor or the PC board (2).
Check the shutter's sealing
material.
Check the shutter for
deformation or its sealing
material.
(Q0346)
208
Service Diagnosis
SiEBE12-625
5.8
Troubleshooting
Front Panel Open / Close Fault
C7
Remote
Controller
Display
Method of
Malfunction
Detection
Malfunction
Decision
Conditions
„ The system will be shut down when the error occurs twice.
Supposed
Causes
„ Malfunction of the reduction motor
„ Malfunction or deterioration of the front panel mechanism
„ Malfunction of the limit switch
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Restart and check
the movement.
Does it move?
YES
NO
Remove the front panel and
check the movement.
Does it move?
NO
Replace the reduction motor.
YES
Does it open / close
fully?
NO
YES
Restart.
Does the error code
reappear?
YES
NO
Replace the assembly of the
front panel mechanism.
HCheck the movement of the
right and left separately by
hand.
It is supposed such as
deformation of the panel or
stuffed dust.
Find out the cause.
Replace the limit switch.
(R3313)
Note:
Service Diagnosis
You cannot operate the unit by the remote controller when the front panel mechanism breaks
down.
<To the dealers: temporary measure before repair>
1. Pull the plug out or turn the breaker off.
2. Remove the decorative plate.
3. Remove the slot-in panel.
4. Put the plug in or turn the breaker on.
(Wait until the initialization finishes.)
5. Operate the unit by the indoor unit ON/OFF switch.
209
Troubleshooting
5.9
SiEBE12-625
Signal Transmission Error (between Indoor and Outdoor
Units)
Remote
Controller
Display
U4
Method of
Malfunction
Detection
The data received from the outdoor unit in indoor unit-outdoor unit signal transmission is
checked whether it is normal.
Malfunction
Decision
Conditions
When the data sent from the outdoor unit cannot be received normally, or when the content of
the data is abnormal.
Supposed
Causes
„
„
„
„
„
Faulty outdoor unit PCB.
Faulty indoor unit PCB.
Indoor unit-outdoor unit signal transmission error due to wiring error.
Indoor unit-outdoor unit signal transmission error due to disturbed power supply waveform.
Indoor unit-outdoor unit signal transmission error due to breaking of wire in the connection
wires between the indoor and outdoor units (wire No. 2).
Troubleshooting
Caution
Check No.10
Refer to P.245
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the indoor unit-outdoor unit
connection wires.
Is there any wiring error?
YES
Correct the indoor unit-outdoor
unit connection wires.
NO
Check the outdoor unit's LED A.
Is LED A flashing?
NO
Diagnose the outdoor unit.
YES
Check the voltage of the indoor
unit-outdoor unit connection wires
between No. 1 and No. 2, and
between No 2 and No. 3.
Is the voltage 0 V?
YES
Replace the connection wires
between the indoor and
outdoor units.
NO
Replace indoor unit control
PCB .
NO
Check No. 10
Check power supply waveform.
Is there any disturbance?
YES
210
Locate the cause of the
disturbance of the power supply
waveform, and correct it.
(R2840)
Service Diagnosis
SiEBE12-625
Troubleshooting
5.10 Unspecified Voltage (between Indoor and Outdoor Units)
Remote
Controller
Display
UA
Method of
Malfunction
Detection
The supply power is detected for its requirements (different from pair type and multi type) by the
indoor / outdoor transmission signal.
Malfunction
Decision
Conditions
The pair type and multi type are interconnected.
Supposed
Causes
„
„
„
„
Wrong models interconnected
Wrong indoor unit PCB mounted
Indoor unit PCB defective
Wrong outdoor unit PCB mounted or defective
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the indoor and outdoor unit
model numbers.
Indoor unit and outdoor unit
matched?
NO
Match the compatible
models.
YES
Check the code numbers
(2P01234, for example) of the
indoor and outdoor unit PCB with
the Parts List.
Matched compatibly?
YES
NO
Change for the specified
PCB (1) or (2).
Replace the indoor unit
PCB (1) (or the outdoor unit
PCB).
(Q0347)
Service Diagnosis
211
Troubleshooting
SiEBE12-625
5.11 Freeze-up Protection Control
Remote
Controller
Display
A5
Outdoor Unit LED
Display
A5 14 21 34 44
Method of
Malfunction
Detection
Indoor unit icing, during cooling operation, is detected by checking the temperatures sensed by
the indoor unit heat exchanger thermistor and room temperature thermistor that are located in a
shut-down room.
Malfunction
Decision
Conditions
In the cooling mode, the following conditions (A) and (B) are kept together for 5 minutes.
(A) Indoor unit heat exchanger temperature ≤ –1°C
(B) Indoor unit heat exchanger temperature ≤ Room temperature –10°C
If the freeze-up protection control is activated 4 times continuously, the system will be shut
down.
(The 4-time counter will reset itself if any of the following errors does not occur for 60
minutes: OL, radiation fin temperature rise, gas shortage, and compressor startup.)
Supposed
Causes
212
„
„
„
„
„
Wrong wiring or piping
EV malfunctioning in each room
Short-circuit
Indoor unit heat exchanger thermistor defective
Room temperature thermistor defective
Service Diagnosis
SiEBE12-625
Troubleshooting
Troubleshooting
Caution
Check No.04
Refer to P.240
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the wiring and piping.
Wiring or piping out of spec?
YES
Activate the wiring error
check mode.
NO
Check No. 04
Check the electronic expansion
valve.
Motor functioning?
NO
Replace the defective EV or
coil.
YES
Check No. 06
Check the outdoor unit heat
exchanger thermistor.
Thermistor as specified
in its characteristic
chart?
NO
Replace the heat
exchanger thermistor.
YES
Check No. 06
Check the room temperature
thermistor.
Thermistor as specified
in its characteristic
chart?
NO
Replace the room
temperature thermistor.
YES
Change the gas to let moisture out
of the unit (after drawing a
vacuum).
Error again?
NO
YES
Replace the room
temperature thermistor or
indoor unit heat exchanger
thermistor.
Do the vacuum-drying.
Replace the indoor unit
PCB and then start the
wiring error check mode.
(R4715)
Service Diagnosis
213
Troubleshooting
SiEBE12-625
5.12 OL Activation (Compressor Overload)
Remote
Controller
Display
E5
Outdoor Unit LED
Display
A5 1
4
21 34 41
Method of
Malfunction
Detection
A compressor overload is detected through compressor OL.
Malfunction
Decision
Conditions
„ If the compressor OL is activated twice, the system will be shut down.
„ The error counter will reset itself if this or any other error does not occur during the following
60-minute compressor running time (total time).
∗ The operating temperature condition is not specified.
Supposed
Causes
„
„
„
„
„
„
Refrigerant shortage
Four way valve malfunctioning
Outdoor unit PCB defective
Water mixed in the local piping
Electronic expansion valve defective
Stop valve defective
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check No.04
Refer to P.240
Discharge pipe thermistor
disconnected?
Check No.05
Refer to P.241
Malfunctioning
∗ Discharge pipe thermistor
Malfunctioning
Replace the valve itself or
the coil.
Functioning
Check No. 05
Check the four way valve.
Malfunctioning
Functioning
Check No. 11
Check the refrigerant line.
Functioning
214
Replace the discharge pipe
thermistor.
Functioning
Check No. 04
Check the electronic expantion
valve.
Check No.11
Refer to P.245
Insert the thermistor in
position.
NO
Check No. 06
Check the thermistors
Check No.06
Refer to P.242
YES
Malfunctioning
∗ Refrigerant shortage
∗ Water mixed
∗ Stop valve defective
Replace the four way valve
coil or the valve itself.
Replace the outdoor unit
PCB.
Refer to the refrigerant line
check procedure.
Replace the outdoor unit
PCB.
(R4697)
Service Diagnosis
SiEBE12-625
Troubleshooting
5.13 Compressor Lock
Remote
Controller
Display
E6
Outdoor Unit LED
Display
A5 11 24 34 41
Method of
Malfunction
Detection
A compressor lock is detected by checking the compressor running condition through the
position detection circuit.
Malfunction
Decision
Conditions
„ The position detection circuit detects a compressor frequency of below 10 Hz for 20 seconds
or a frequency of above 160 Hz.
„ 40 seconds after the compressor has started, the position detection circuit detects a
compressor frequency of above 180 Hz.
„ The system will be shut down if the error occurs 16 times.
„ Clearing condition: Continuous run for about 5 minutes (normal)
Supposed
Causes
„ Compressor locked
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn off the power. Disconnect the
harnesses U, V and W.
∗ Inverter checker
Part No.: 1225477
Check with the inverter checker (∗).
Normal?
NO
YES
Turn off the power and reconnect the
harnesses. Turn on the power again
and get the system restarted.
Emergency stop
without compressor
running?
YES
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
Replace the compressor.
NO
System shut
down after errors repeated
several times?
YES
NO
Check the electronic
expansion valve.
Replace it as required.
Replace the compressor.
(R2842)
Service Diagnosis
215
Troubleshooting
SiEBE12-625
5.14 DC Fan Lock
Remote
Controller
Display
E7
Outdoor Unit LED
Display
A5 14 24 34 44
Method of
Malfunction
Detection
A fan motor line error is detected by checking the high-voltage fan motor rpm being detected by
the Hall IC.
Malfunction
Decision
Conditions
„ The fan does not start in 30 seconds even when the fan motor is running.
„ The system will be shut down if the error occurs 16 times.
„ Clearing condition: Continuous run for about 5 minutes (normal)
Supposed
Causes
„ Fan motor breakdown
„ Harness or connector disconnected between fan motor and PCB or in poor contact
„ Foreign matters stuck in the fan
Troubleshooting
Check No.15
Refer to P.247
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Fan motor connector
disconnected?
YES
Turn off the power and
reconnect the connector.
NO
Foreign matters in or
around the fan?
YES
Remove.
NO
Get started.
Check No. 15
Check the outdoor unit PCB rpm
pulse input.
Pulse signal inputted?
YES
NO
Replace the outdoor unit
fan motor.
Replace the outdoor unit
PCB.
(R2843)
216
Service Diagnosis
SiEBE12-625
Troubleshooting
5.15 Input Over Current Detection
Remote
Controller
Display
E8
Outdoor Unit LED
Display
A5 11 24 31 44
Method of
Malfunction
Detection
Malfunction is detected by checking the input current value.
Malfunction
Decision
Conditions
„ The following condition continues for 2.5 seconds.
Input current ≥ 11A (typical value)
„ The compressor halts if the error occurs, and restarts automatically after 3 minutes stand-by.
Supposed
Causes
„
„
„
„
„
„
Service Diagnosis
Over-current due to compressor failure
Over-current due to defective power transistor
Over-current due to defective inverter main circuit electrolytic capacitor
Over-current due to defective outdoor unit PCB
Error detection due to outdoor unit PCB
Over-current due to short-circuit
217
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Check No.07
Refer to P.243
Check No.08
Refer to P.244
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
* An input over-current may result from wrong internal wiring. If the wires have been disconnected and
reconnected for part replacement, for example, and the system is interrupted by an input over-current,
take the following procedure.
Get restarted and measure the
input current.
Input current flowing
above its stop level?
Check No.14
Refer to P.247
NO
Replace the outdoor unit
PCB.
YES
Check No. 14
Check the main circuit electrolytic
capacitor.
NO
Normal?
Replace the electrolytic
capacitor.
YES
Turn off the power and disconnect
the harnesses U, V and W.
* Inverter checker
Part No.: 1225477
Check with the inverter checker (*).
Any LED off?
NO
Turn off the power, and reconnect
the harnesses. Turn on the power
again and get restarted.
YES
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
Check No. 08
Check the discharge pressure.
Check No. 07
Check the installation condition.
(R4716)
218
Service Diagnosis
SiEBE12-625
Troubleshooting
5.16 Four Way Valve Abnormality
Remote
Controller
Display
EA
Outdoor Unit LED
Display
A5 14 21 31 41
Method of
Malfunction
Detection
The liquid pipe thermistor, the outdoor temperature thermistor and the outdoor unit heat
exchanger thermistor are checked to see if they function within their normal ranges in the
operating mode.
Malfunction
Decision
Conditions
Either of the following conditions occurs 6 minutes after the compressor has started.
„ Cooling / dry operation
(Outdoor unit heat exchanger temperature – Liquid pipe temperature) < –5°C
„ Heating operation
(Liquid pipe temperature – Outdoor unit heat exchanger temperature) < 0°C
Supposed
Causes
„
„
„
„
„
„
Service Diagnosis
Connector in poor contact
Thermistor defective
Outdoor unit PCB defective
Four way valve coil or harness defective
Four way valve defective
Foreign substance mixed in refrigerant
219
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Check No.05
Refer to P.241
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Four-way valve coil
disconnected (loose)?
YES
Correct.
NO
Check No.06
Refer to P.242
Check No.11
Refer to P.245
Harness out of connector?
YES
Reconnect.
NO
Check the continuity of the
four-way valve coil and harness.
Disconnect
the harness from the
connector. Resistance between
harnesses about
1500 ohms?
NO
Replace the four-way valve
coil.
YES
Check No. 05
Check the four-way valve
switching output.
Malfunctioning
Replace the outdoor unit
PC board.
Functioning
Any thermistor disconnected?
YES
Reconnect in position.
NO
Check No. 06
Check the thermistors.
Malfunctioning
Replace a defective
thermistor.
Functioning
Check No. 11
Check the refrigerant line.
Malfunctioning
Water mixed
Shut-off valve defective
Refer to the refrigerant line
check procedure.
Functioning
Replace the four-way valve
(defective or dust-clogged).
(R4717)
220
Service Diagnosis
SiEBE12-625
Troubleshooting
5.17 Discharge Pipe Temperature Control
Remote
Controller
Display
F3
Outdoor Unit LED
Display
A5 14 21 34 41
Method of
Malfunction
Detection
The discharge pipe temperature control (stop, frequency drooping, etc.) is checked with the
temperature being detected by the discharge pipe thermistor.
Malfunction
Decision
Conditions
2YC45
If the temperature being detected by the discharge pipe thermistor rises above 120°C, the
compressor will stop. (The error is cleared when the temperature has dropped below 107°C.)
„ If the compressor stops 6 times straight due to abnormal discharge pipe temperature, the
system will be shut down.
„ The error counter will reset itself if this or any other error does not occur during the following
60-minute compressor running time (total time).
Supposed
Causes
„ Refrigerant shortage
„ Four way valve malfunctioning
„ Discharge pipe thermistor defective
(heat exchanger or outdoor temperature thermistor defective)
„ Outdoor unit PCB defective
„ Water mixed in the local piping
„ Electronic expansion valve defective
„ Stop valve defective
Troubleshooting
Caution
Check No.04
Refer to P.240
Check No.06
Refer to P.242
Check No.11
Refer to P.245
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check No. 06
Check the thermistors.
Functioning
Check No. 04
Check the electronic
expansion valve.
Malfunctioning
Discharge pipe thermistor
Outdoor unit heat exchanger thermistor
Outdoor temperature thermistor
Malfunctioning
Replace a defective
thermistor.
Replace the valve itself or
the coil.
Functioning
Check No. 11
Check the refrigerant line.
Functioning
Malfunctioning
Refrigerant shortage
Four way valve malfunctioning
Water mixed
Stop valve defective
Refer to the refrigerant line
check procedure.
Replace the outdoor unit
PCB.
(R4700)
Service Diagnosis
221
Troubleshooting
SiEBE12-625
5.18 High Pressure Control in Cooling
Remote
Controller
Display
F6
Outdoor Unit LED
Display
A5 14 21 34 44
Method of
Malfunction
Detection
High-pressure control (stop, frequency drop, etc.) is activated in the cooling mode if the
temperature being sensed by the heat exchanger thermistor exceeds the limit.
Malfunction
Decision
Conditions
„ Activated when the temperature being sensed by the heat exchanger thermistor rises above
65°C.
„ The error is cleared when the temperature drops below 50°C.
Supposed
Causes
„
„
„
„
„
„
„
222
The installation space is not large enough.
Faulty outdoor unit fan
Faulty electronic expansion valve
Faulty outdoor unit heat exchanger thermistor
Faulty outdoor unit PCB
Faulty stop valve
Dirty heat exchanger
Service Diagnosis
SiEBE12-625
Troubleshooting
Troubleshooting
Check No.04
Refer to P.240
Check No.06
Refer to P.242
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the installation space.
Check No.07
Refer to P.243
Check No.09
Refer to P.244
Check No.07
Installation condition
check
Abnormal
Normal
Check No.09
Outdoor fan check
Abnormal
Change the air outlet grille
position.
Change the installation
location.
Clean the heat exchanger.
Replace the fan motor.
Repair the connector or fan
motor lead wires.
Normal
Check No.04
Electronic expansion valve check
Judgment
Abnormal
Replace the electronic
expansion valve or coil.
Replace the PCB.
Normal
Check No.06
Heat exchanger thermistor check
Judgment
Abnormal
Replace the heat exchanger
thermistor.
Normal
Replace PCB.
(R4701)
Service Diagnosis
223
Troubleshooting
SiEBE12-625
5.19 Position Sensor Abnormality
Remote
Controller
Display
H6
Outdoor Unit LED
Display
A5 14 24 31 41
Method of
Malfunction
Detection
A compressor startup failure is detected by checking the compressor running condition through
the position detection circuit.
Malfunction
Decision
Conditions
„ The compressor fails to start in about 15 seconds after the compressor run command signal
is sent.
„ Clearing condition: Continuous run for about 5 minutes (normal)
„ The system will be shut down if the error occurs 16 times.
Supposed
Causes
„
„
„
„
„
Compressor relay cable disconnected
Compressor itself defective
Outdoor unit PCB defective
Stop valve closed
Input voltage out of specification
Troubleshooting
Caution
Check No.13
Refer to P.246
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check No. 13
Check for short-circuit.
Normal
NO
Replace the outdoor unit
PCB, outdoor unit fan.
YES
Check the electrolytic capacitor
voltage.
DC380±30V?
NO
Replace the outdoor unit
PCB.
YES
Electricals
or compressor harnesses
connected as
specified?
NO
Reconnect as specified.
Turn off the power. Disconnect the
harnesses U, V and W.
∗ Inverter checker
Part No.: 1225477
Check with the inverter checker (∗).
YES
Any LED off?
NO
Correct the power supply or
replace the outdoor unit
PCB.
Replace the compressor.
(R2847)
224
Service Diagnosis
SiEBE12-625
Troubleshooting
5.20 CT or Related Abnormality
Remote
Controller
Display
H8
Outdoor Unit LED
Display
A5 14 24 31 41
Method of
Malfunction
Detection
A CT or related error is detected by checking the compressor running frequency and CTdetected input current.
Malfunction
Decision
Conditions
„ The compressor running frequency is below 55 Hz and the CT input is below 0.1 V.
(The input current is also below 1.25 A.)
„ If this error repeats 4 times, the system will be shut down.
„ The error counter will reset itself if this or any other error does not occur during the following
60-minute compressor running time (total time).
Supposed
Causes
„
„
„
„
Service Diagnosis
Power transistor defective
Internal wiring broken or in poor contact
Reactor defective
Outdoor unit PCB defective
225
Troubleshooting
SiEBE12-625
Troubleshooting
Check No.12
Refer to P.246
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn off the power and turn it on
again.
Get the system started.
∗ Running current
as shown at right with relay
cable 1 or 2?
YES
Current
(guideline)
NO
Check No. 12
Check the capacitor voltage.
Rising with increasing
frequency
2 sec
DC380±30V?
Replace the outdoor unit
PCB.
Capacitor charged when
the indoor unit or outdoor
unit main relay turns on
Time
YES Turn off the power. Disconnect the
harnesses U, V and W.
NO
Check with the inverter checker (∗).
Measure the rectifier input voltage.
Any LED off?
YES
NO
Turn off the power and reconnect
the above harnesses. Then turn on
the power again and get the
system restarted.
Compressor running?
NO
Voltage within
the allowable range (Supply
voltage±15%)?
NO
YES
* Inverter checker
Part No.: 1225477
YES
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
Replace the outdoor unit
PCB.
Replace the compressor.
Replace the outdoor unit
PCB.
Check the supply voltage.
(R2848)
226
Service Diagnosis
SiEBE12-625
Troubleshooting
5.21 Thermistor or Related Abnormality (Outdoor Unit)
Remote
Controller
Display
P4, J3, J6, J8, J9, H9
Outdoor Unit LED
Display
A5 14 24 31 41
Method of
Malfunction
Detection
This type of error is detected by checking the thermistor input voltage to the microcomputer.
[A thermistor error is detected by checking the temperature being detected by each thermistor.]
Malfunction
Decision
Conditions
When the thermistor input is above 4.96 V or below 0.04 V with the power on, the J3 error is
judged if the discharge pipe thermistor temperature is smaller than the condenser thermistor
temperature, or the system will be shut down if all the units are judged with the J8 error.
Supposed
Causes
„
„
„
„
„
Service Diagnosis
Connector in poor contact
Thermistor defective
Outdoor unit PCB defective
Indoor unit PCB defective
Condenser thermistor defective in the case of J3 error (outdoor unit heat exchanger
thermistor in the cooling mode, or indoor unit heat exchanger thermistor in the heating
mode)
227
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn on the power again.
Error displayed
again on remote
control?
NO
Reconnect.
YES
Connector or thermistor
disconnected?
YES
Reconnect.
NO
Check No. 06
Check the thermistor resistance
value.
Normal?
J3 error if discharge pipe
thermistor temperature is
smaller than condenser
thermistor temperature
NO
YES
Cooling: Outdoor unit heat
exchanger thermistor
Heating: Indoor unit heat
exchanger thermistor
Check No. 06
Check the indoor unit heat
exchanger thermistor resistance
value in the heating mode.
Indoor unit
heat exchanger thermistor
functioning?
NO
YES
Replace defective one(s) of
the following thermistors.
Radiation fin thermistor
Discharge pipe
thermistor
Outdoor unit heat
exchanger thermistor
Liquid pipe thermistor
Gas pipe thermistor
Outdoor temperature
thermistor
Replace the following
thermistor.
Indoor unit heat
exchanger thermistor
Replace the outdoor unit
PC board. (Replace the
indoor unit PC board.)
(R4718)
P4 : Radiation fin thermistor
J3 : Discharge pipe thermistor
J6 : Outdoor unit heat exchanger thermistor
J8 : Liquid pipe thermistor
J9 : Gas pipe thermistor
H9 : Outdoor temperature thermistor
228
Service Diagnosis
SiEBE12-625
Troubleshooting
5.22 Electrical Box Temperature Rise
Remote
Controller
Display
L3
Outdoor Unit LED
Display
A5 14 24 31 44
Method of
Malfunction
Detection
An electrical box temperature rise is detected by checking the radiation fin thermistor with the
compressor off.
Malfunction
Decision
Conditions
„ With the compressor off, the radiation fin temperature is above 80°C (above 75°C for 80 · 90
class).
„ The error is cleared when the temperature drops below 70°C (below 65°C for 80 · 90 class).
Supposed
Causes
„
„
„
„
„
Service Diagnosis
Fin temperature rise due to defective outdoor unit fan
Fin temperature rise due to short-circuit
Fin thermistor defective
Connector in poor contact
Outdoor unit PCB defective
229
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn off the power and turn it on
again.
Check No.07
Refer to P.243
Error again or outdoor unit
fan activated?
Check No.09
Refer to P.244
WARNING
To cool down the electricals, the
outdoor unit fan gets started when
the radiation fin temperature rises
above 80°C and stops itself when
it drops below 70°C.
YES
NO
Check No. 06
Check the thermistor resistance
value.
Fin thermistor
Check the radiation fin
temperature.
Thermistor as
specified in its characteristic
chart?
NO
Replace the fin thermistor.
YES
Above 80°C?
NO
Replace the outdoor unit
PCB.
YES
Check No. 09
Check the outdoor unit
fan or related.
Malfunctioning
Functioning
Radiation fin dirty?
Too dirty
Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.
Clean up the radiation fin.
Slightly dirty
Check No. 07
Check the installation condition.
(R4712)
230
Service Diagnosis
SiEBE12-625
Troubleshooting
5.23 Radiation Fin Temperature Rise
Remote
Controller
Display
L4
Outdoor Unit LED
Display
A5 11 21 31 44
Method of
Malfunction
Detection
A radiation fin temperature rise is detected by checking the radiation fin temperature being
detected by the fin thermistor with the compressor on.
Malfunction
Decision
Conditions
„ The radiation fin temperature with the compressor on is above 90°C (above 85°C for 80 · 90
class).
„ The error is cleared when the temperature drops below 85°C (below 80°C for 80 · 90 class).
„ If a radiation fin temperature rise takes place 255 times successively, the system will be shut
down.
„ The error counter will reset itself if this or any other error does not occur during the following
60-minute compressor running time (total time).
Supposed
Causes
„
„
„
„
„
Service Diagnosis
Fin temperature rise due to defective outdoor unit fan
Fin temperature rise due to short-circuit
Fin thermistor defective
Connector in poor contact
Outdoor unit PCB defective
231
Troubleshooting
SiEBE12-625
Troubleshooting
Caution
Check No.06
Refer to P.242
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Turn off the power and turn it on
again to get the system started.
Check No.07
Refer to P.243
Error displayed again?
Check No.09
Refer to P.244
YES
NO
Check No. 06
Check the thermistor resistance
value.
Fin thermistor
Check the radiation fin
temperature.
Thermistor as
specified in its characteristic
chart?
NO
Replace the fin thermistor.
YES
Above 90°C?
YES
Check No.09
Check the outdoor unit fan or
related.
Malfunctioning
Functioning
Radiation fin dirty?
Too dirty
NO
Check the power transistor
and fin for looseness. If
they are found to be fit
tightly, replace the PCB or
the power transistor.
Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.
Clean up the radiation fin.
Slightly dirty
Check No. 07
Check the installation condition.
232
(R4713)
Service Diagnosis
SiEBE12-625
Troubleshooting
5.24 Output Over Current Detection
Remote
Controller
Display
L5
Outdoor Unit LED
Display
A5 11 21 34 41
Method of
Malfunction
Detection
An output over-current is detected by checking the current that flows in the inverter DC section.
Malfunction
Decision
Conditions
„ A position signal error occurs while the compressor is running.
„ A speed error occurs while the compressor is running.
„ An output over-current input is fed from the output over-current detection circuit to the
microcomputer.
„ The system will be shut down if the error occurs 16 times.
„ Clearing condition: Continuous run for about 5 minutes (normal)
Supposed
Causes
„
„
„
„
„
„
„
„
Service Diagnosis
Over-current due to defective power transistor
Over-current due to wrong internal wiring
Over-current due to abnormal supply voltage
Over-current due to defective PCB
Error detection due to defective PCB
Over-current due to closed stop valve
Over-current due to compressor failure
Over-current due to poor installation condition
233
Troubleshooting
SiEBE12-625
Troubleshooting
Check No.07
Refer to P.243
Check No.08
Refer to P.244
Check No.13
Refer to P.246
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
* An output over-current may result from wrong internal wiring. If the wires have been disconnected and
reconnected for part replacement, for example, and the system is interrupted by an output over-current,
take the following procedure.
NO
Stop valve fully open?
Fully open the stop valve.
YES
Turn off the power and turn it on
again to get the system started.
See if the same error occurs.
Error again?
NO Monitor the supply voltage,
discharge and suction pressures,
and other factors for a long term.
Possible causes
Instantaneous supply voltage
drop
Compressor motor overloaded
Contact-induced electrical
short-circuit
YES
Turn off the power and disconnect
the harnesses U, V and W.
* Inverter checker
Part No.: 1225477
Check with the inverter checker (*).
Any LED off?
Keep on using as it is
(monitor).
Check the electricals'
connectors and other
fittings.
YES
NO
Correct the power supply or
replace the SPM.
(Replace the outdoor unit
PCB.)
Check No. 13
Check the power transistor.
Normal?
NO
Replace the SPM.
(Replace the outdoor unit
PCB.)
YES
Turn off the power, and reconnect
the harnesses. Turn on the power
again and get restarted.
Check the supply voltage.
Voltage as rated?
NO
Correct the power supply.
YES
Short-circuit
or breakage between
compressor's coil
phases?
YES
Replace the compressor.
NO
Check No. 08
Check the discharge pressure.
Check No. 07
Check the installation condition.
(R4705)
234
Service Diagnosis
SiEBE12-625
Troubleshooting
5.25 Insufficient Gas
Remote
Controller
Display
U0
Outdoor Unit LED
Display
A5 11 21 34 44
Method of
Malfunction
Detection
Gas shortage detection I:
Gas shortage is detected by checking the input current value and the compressor running
frequency. If the gas is short, the input current is smaller than the normal value.
Gas shortage detection II:
Gas shortage is detected by checking the discharge temperature and the opening of the
electronic expansion valve. If the gas is short, the discharge temperature tends to rise.
Malfunction
Decision
Conditions
Gas shortage detection I (typical value):
The following conditions continue for 7 minutes.
Š Input current × input voltage ≤ 1756 / 256 × output frequency +50 (W)
Š Output frequency > 55 (Hz)
Gas shortage detection II:
The following conditions continue for 80 seconds.
Š Target opening of the electronic expansion valve ≥ 450 (pulse)
Š Cooling: discharge temperature > 255 / 256 × target discharge temperature +20 (°C)
Heating: discharge temperature > 255 / 256 × target discharge temperature +40 (°C)
If a gas shortage error takes place 4 times straight, the system will be shut down. The error
counter will reset itself if this or any other error does not occur during the following 60-minute
compressor running time (total time).
Supposed
Causes
Service Diagnosis
„ Refrigerant shortage (refrigerant leakage)
„ Poor compression performance of compressor
„ Discharge pipe thermistor disconnected, or indoor unit or outdoor unit heat exchanger
thermistor disconnected, room or outside air temperature thermistor disconnected
„ Stop valve closed
„ Electronic expansion valve defective
235
Troubleshooting
SiEBE12-625
Troubleshooting
Check No.04
Refer to P.240
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Any thermistor
disconnected?
Check No.06
Refer to P.242
NO
Stop valve closed?
YES
Reconnect in position.
* Discharge pipe thermistor
* Indoor / outdoor unit heat exchanger thermistor
* Room temperature thermistor
* Outdoor air thermistor
YES
Open the stop valve.
NO
Check for gas leakage.
Oil oozing at relay pipe
connections?
YES
Repair the pipe flare or
replace the square union.
NO
Oil oozing at internal piping?
YES
NO
Check No. 04
Electronic expansion valve
functioning?
Compressor vibrating
too much?
NO
NO
Check the pipes for
improper contact. Correct
as required. Also replace
cracked pipe if any.
YES
Check the CT.
YES Check the power transistor
harness for looseness.
Correct it as required. Also
replace cracked pipe if any.
Replace the electronic
expansion valve.
Malfunctioning
CT in trouble (refer to H8).
Functioning
Change for a specified amount of
fresh refrigerant.
Gas shortage error again?
NO
YES
Malfunctioning Replace the room
Check No. 06
Check the thermistors.
Functioning
temperature or outdoor air
thermistor, or the indoor
unit or outdoor unit heat
exchanger thermistor.
(1) Replace the PCB.
(2) Replace the compressor.
Procedure complete
(R4719)
236
Service Diagnosis
SiEBE12-625
Troubleshooting
5.26 Low-voltage Detection
Remote
Controller
Display
U2
Outdoor Unit LED
Display
A5 14 21 31 44
Method of
Malfunction
Detection
An abnormal voltage rise or drop is detected by checking the detection circuit or DC voltage
detection circuit.
Malfunction
Decision
Conditions
„ An over-voltage signal is fed from the over-voltage detection circuit to the microcomputer, or
the voltage being detected by the DC voltage detection circuit is judged to be below 150 V
for 0.1 second.
„ The system will be shut down if the error occurs 16 times.
„ Clearing condition: Continuous run for about 60 minutes (normal)
Supposed
Causes
„ Supply voltage not as specified
„ Over-voltage detector or DC voltage detection circuit defective
„ PAM control part(s) defective
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Check the supply voltage.
Supply voltage as
specified?
NO
Correct the power supply.
YES
(Precaution before turning on the power again)
Make sure the power has been off for
at least 30 seconds.
Turn on the power again.
System restarted?
NO
Repeat a couple
of times.
YES
Disturbance factors
∗ Noise ∗ Power supply distortion
Check for such factors for a
long term.
∗ Try to get restarted a
couple of times.
Replace the SPM.
(Replace the outdoor unit
PCB.)
(R2854)
Service Diagnosis
237
Troubleshooting
SiEBE12-625
5.27 Anti-icing Function in Other Rooms / Unspecified
Voltage (between Indoor and Outdoor Units)
Remote
Controller
Display
UA, UH
Outdoor Unit LED
Display
A5 11 21 31 41
Method of
Malfunction
Detection
A wrong connection is detected by checking the combination of indoor and outdoor units on the
microcomputer.
Malfunction
Decision
Conditions
„ Operation halt due to the anti-icing function in other rooms
„ Operation halt due to unspecified internal and/or external voltages
„ Operation halt due to mismatching of indoor and outdoor units
Supposed
Causes
„ Operation halt due to the anti-icing function in other rooms
„ Wrong connections at the indoor unit
„ PCB wrongly connected
Troubleshooting
Caution
Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.
Error-displaying
air-conditioner running?
NO
The freeze protection
function is activated in other
rooms. Refer to A5.
YES
Supply voltage
as specified?
NO
Correct.
YES
Check the model name.
Normal?
NO
Reconnect.
YES
Check the combination of all the
models being connected.
(R3066)
238
Service Diagnosis
SiEBE12-625
Check
6. Check
6.1
How to Check
6.1.1 Fan Motor Connector Output Check
Check No.01
1.
2.
3.
4.
5.
Check connector connection.
Check motor power supply voltage output (pins 4-7 and 4-8).
Check motor control voltage (pins 4-3).
Check rotation command voltage output (pins 4-2).
Check rotation pulse input (pins 4-1).
S1 or S301
7
6
5
4
3
2
1
S302
8
7
6
5
4
3
2
1
Motor power supply voltage
Unused
Unused
P.0V (reference potential)
Motor control voltage (15 VDC)
Rotation command voltage (1~ 5 VDC)
Rotation pulse input
Motor power supply voltage
Unused
Unused
Unused
P.0V (reference potential)
Motor control voltage (15 VDC)
Rotation command voltage (1 to 5 VDC)
Rotation pulse input
(R4684)
Check No.02
1. Check connector connection.
2. Check motor control voltage output (pins 2-1).
S202
5
4
3
2
1
Motor power supply voltage
Unused
Unused
P.0V (reference potential)
Motor control power supply
(R1073)
6.1.2 Limit Switch Continuity Check
Check No.03
Remove the front grille. The limit switch is located at the left side of the drain pan assembly.
Check the continuity of the switch connection.
Shutter status
Open
Closed
Continuity
Continuity
No continuity
Upward
Tester
Limit switch
Forward
(Q0363)
∗ The shutter can be opened and closed with hand. Keep the shutter open and closed all the
way for each continuity check steps.
Service Diagnosis
239
Check
SiEBE12-625
6.1.3 Electronic Expansion Valve Check
Check No.04
Conduct the followings to check the electronic expansion valve (EV).
1. Check to see if the EV connector is correctly inserted in the PCB. Compare the EV unit and
the connector number.
2. Turn the power off and back on again, and check to see if all the EVs generate latching
sound.
3. If any of the EVs does not generate latching noise in the above step 2, disconnect that
connector and check the conductivity using a tester.
Check the conductivity between pins 1, 3 and 6, and between pins 2, 4 and 5. If there is no
conductivity between the pins, the EV coil is faulty.
4. If no EV generates latching sound in the above step 2, the outdoor unit PCB is faulty.
5. If the conductivity is confirmed in the above step 2, mount a good coil (which generated
latching sound) in the EV unit that did not generate latching sound, and check to see if that
EV generates latching sound.
∗If latching sound is generated, the outdoor unit PCB is faulty.
∗If latching sound is not generated, the EV unit is faulty.
Note:
Please note that the latching sound varies depending on the valve type.
Valve Body Condition (Symptom)
Check Method / Measure
(1) Valve body catches at fully opened or half
Reset power supply and conduct cooling
opened position.
operation unit by unit.
(Symptom)
Cooling:
Check the liquid pipe temperature
„Water leakage at the no-operation unit
of no-operation unit.
„Flow noise of refrigerant in the no-operation unit
„Operation halt due to icing protection
Heating:
„The unit does not heat
„Refrigerant flow rate vary by unit
(Discharge air temperatures are different by
room)
„Peak cut
Is it
almost same as the
outside air
temperature?
NO
YES
Replace the EVn of the room.
(R1431)
(2) Valve body catches at complete close
Reset power supply and conduct cooling
position.
operation unit by unit.
(Symptom)
Cooling:
Check the low pressure
„The only unit having problem does not cool the
room .
„When the only faulty unit is in operation, the unit
makes pump down.
Does the
(The low pressure of the unit becomes vacuum)
pressure become into vacuum
NO
zone?
„IT is activated.
„Abnormal discharge pipe temperature
YES
Heating:
Insufficient gas due to liquid refrigerant
stagnation inside
the faulty indoor unit
(Only for heat pump model)
„The unit does not heat the room.
„IT is activated.
„Abnormal discharge pipe temperature
(3) Valve does not open fully.
(Symptom)
„The unit does not cool nor heat (only for heat
pump model.)
„IT is actuated.
„Abnormal discharge pipe temperature
240
Replace the EVn of the room
(R1432)
Check the number of rotation of shaft if it is 5 and
half from full open to complete close using
manual coil for electronic expansion valve. When
the number of rotation of shaft is less than the
above value, the valve may catch anywhere of
the body.
Service Diagnosis
SiEBE12-625
Check
6.1.4 Four Way Valve Performance Check
Check No.05
Turn off the power and turn it on
again.
Start the heating-mode run.
S80 voltage
at DC 180-220 V with
compressor on?
(Fig. 1)
∗ Four way valve coil
Cooling / dry : No continuity
Heating : Continuity
NO
Replace the outdoor unit
PCB.
YES
Disconnect the four way valve coil
from the connector and check the
continuity.
Four way valve
coil resistance at
1500 ohms?
NO
YES
Replace the four way valve
coil.
Replace the four way valve.
(Fig. 1)
Voltage at S80
DC180-220V
Compressor
Time
ON
Service Diagnosis
(R2856)
241
Check
SiEBE12-625
6.1.5 Thermistor Resistance Check
Check No.06
Remove the connectors of the thermistors on the PCB, and measure the resistance of each
thermistor using tester.
The relationship between normal temperature and resistance is shown in the graph and the
table below.
Thermistor R25°C=20kΩ B=3950
Temperature (°C)
-20
-15
-10
-5
0
5
10
15
20
25
30
35
40
45
50
211.0 (kΩ)
150
116.5
88
67.2
51.9
40
31.8
25
20
16
13
10.6
8.7
7.2
Tester
Resistance range
(R25=20k⍀
B=3950)
(k⍀)
(°C)
242
Service Diagnosis
SiEBE12-625
Check
6.1.6 Installation Condition Check
Check No.07
Installation condition check
Check
the allowable
dimensions of the air suction
and discharge
area.
Abnormal
Change the position of the air
discharge grille or the
installation location.
Normal
Does the
discharged air from
other outdoor unit cause an
increase of the suction air
temperature?
YES
Change the position of the air
discharge grille or the
installation location.
NO
Is the heat exchanger
very dirty?
YES
Clean the heat exchanger.
NO
Is the
air flow blocked by
obstacles or winds blowing in
the opposite
direction?
NO
YES
Change the installation
location or direction.
Check the outside air
temperature (temperature of air
taken in by the outdoor unit).
(The outside air temperature
shall be 46°C or lower.)
(R3048)
Service Diagnosis
243
Check
SiEBE12-625
6.1.7 Discharge Pressure Check
Check No.08
Discharge pressure check
NO
High
Replace compessor.
YES
Is the stop valve open?
NO
Open the stop valve.
YES
Is the connection pipe
deformed?
NO
Replace the pipe installed at
the site.
YES
At the
heat exchanger and
air filter dirty?
NO
Clean.
YES
Replace the compressor.
(R1443)
6.1.8 Outdoor Unit Fan System Check (With DC Motor)
Check No.09
Check the outdoor unit fan system.
Outdoor unit fan running?
YES
Outdoor unit fan system
functioning.
244
NO
Fan motor lead wire
connector disconnected?
YES
Reconnect.
NO
Go to Check No. 15.
(R2857)
Service Diagnosis
SiEBE12-625
Check
6.1.9 Power Supply Waveforms Check
Check No.10
Measure the power supply waveform between pins 1 and 3 on the terminal board, and check
the waveform disturbance.
„ Check to see if the power supply waveform is a sine wave (Fig.1).
„ Check to see if there is waveform disturbance near the zero cross (sections circled in Fig.2)
[Fig.1]
[Fig.2]
6.1.10 Inverter Units Refrigerant System Check
Check No.11
Refrigerant system check
Is the
discharge thermister
disconnected from the
holder?
YES
Correct the problem.
NO
Is any moisture found in
sight glass.
NO
Check for gas leaks.
See the section on insufficient gas
detection.
YES
YES
Conduct vacuum drying.
Conduct the check after operating the
equipment for a sufficient length of time.
Replace the refrigerant.
(R1445)
Service Diagnosis
245
Check
SiEBE12-625
6.1.11 Capacitor Voltage Check
Check No.12
Before this checking, be sure to check the main circuit for short-circuit.
„ Checking the capacitor voltage
z With the circuit breaker still on, measure the voltage according to the drawing of the model in
question. Be careful never to touch any live parts.
Use the tester in
the DC range.
Fan motor
lead wire
TB2
P2
TB3
N1
Electronic expansion
valve coil lead wire
(Room A)
Electronic expansion
valve coil lead wire
(Room B)
Compressor
lead wire
Reactor
lead wire
S93
S80
S20 S21 S22 S23
S40 S90 S92
>PS<
Electronic expansion
valve coil lead wire
(Room C)
Electronic expansion
valve coil lead wire
(Room D)
Solenoid valve
lead wire
Thermistor Thermistor
lead wire
lead wire
(liquid pipe) (gas pipe)
OL
lead wire
Thermistor
lead wire
(Q0366)
6.1.12 Power Transistor Check
Check No.13
„ Checking the power transistor
z Never touch any live parts for at least 10 minutes after turning off the circuit breaker.
z If unavoidably necessary to touch a live part, make sure the power transistor's supply
voltage is below 50 V using the tester.
z For the UVW, make measurements at the Faston terminal on the board or the relay
connector.
transistor
Tester's negative terminal Power (+)
Tester's positive terminal
Normal resistance
Abnormal resistance
246
UVW
UVW
Power transistor
(–)
Power transistor
UVW
(+)
Several kohms to several Mohms
0 or ∞
UVW
Power transistor
(–)
Service Diagnosis
SiEBE12-625
Check
6.1.13 Main Circuit Electrolytic Capacitor Check
Check No.14
„ Checking the main circuit electrolytic capacitor
z Never touch any live parts for at least 10 minutes after turning off the circuit breaker.
z If unavoidably necessary to touch a live part, make sure there is no DC voltage using the
tester.
z Check the continuity with the tester. Reverse the pins and make sure there is continuity.
Keep the tester in the
resistance measuring range
When the pointer swings,
it means the capacitor
functions
If the pointer does not swing at all,
or if it swings all the way but does
not return, it means the capacitor
malfunction.
6.1.14 Turning Speed Pulse Input on the Outdoor Unit PCB Check
Check No.15
<Propeller fan motor>
Make sure the voltage of 270±30V is being applied.
(1) Stop the operation first and then the power, and disconnect the connector S70.
(2) Make sure there is about DC 270 V between pins 4 and 7.
(3) With the system and the power still off, reconnect the connector S70.
(4) Make a turn of the fan motor with a hand, and make sure the pulse (0-15 V) appears twice at
pins 1 and 4.
If the fuse is blown out, the outdoor-unit fan may also be in trouble. Check the fan too.
If the voltage in Step (2) is not applied, it means the PCB is defective. Replace the PCB.
If the pulse in Step (4) is not available, it means the Hall IC is defective. Replace the DC fan
motor.If there are both the voltage (2) and the pulse (4), replace the PCB.
PCB
S70
1
2
3
4
5
6
7
Turning speed pulse input (0-15 V)
15V
DC270V
(R2859)
∗ Propeller fan motor : S70
Service Diagnosis
247
Check
SiEBE12-625
6.1.15 Hall IC Check
Check No.16
1. Check the connector connection.
2. With the power ON, operation OFF, and the connector connected, check the following.
∗Output voltage of about 5 V between pins 1 and 3.
∗Generation of 3 pulses between pins 2 and 3 when the fan motor is operating.
Failure of (1) Æ faulty PCB Æ Replace the PCB.
Failure of (2) Æ faulty Hall IC Æ Replace the fan motor.
Both (1) and (2) result Æ Replace the PCB.
The connector has 3 pins, and there are two patterns of lead wire colors.
248
1
Gray (power supply)
2
Purple (signals)
3
Blue (grounding)
1
White (power supply)
2
White with black line(signals)
3
White with manufacturer mark (grounding)
Service Diagnosis
SiEBE12-625
Part 7
Removal Procedure
1. Outdoor Unit (80 / 90 Class) ...............................................................250
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
1.10
Removal of Outer Panels .....................................................................250
Removal of Propeller Fans...................................................................253
Removal of Electrical Box ....................................................................254
Removal of PCB...................................................................................261
Removal of Fan Motor..........................................................................264
Removal of Electronic Expansion Valve and Thermistor .....................266
Removal of Sound Blanket and Reactor ..............................................267
Removal of Shunt.................................................................................269
Removal of Solenoid Valve and Four Way Valve.................................270
Removal of Compressor.......................................................................272
2. Outdoor Unit (68 / 75 Class) ...............................................................274
2.1
2.2
2.3
2.4
2.5
2.6
Removal of Outer Panels .....................................................................274
Removal of Electrical BOX ...................................................................275
Removal of PCB...................................................................................279
Removal of Fan Motor..........................................................................282
Removal of Sound Blanket...................................................................283
Removal of Four Way Valve Coil, Solenoid Valve Coil,
Electronic Expansion Valve Coil and Thermistor .................................284
2.7 Removal of Four Way Valve, Solenoid Valve and Shunt .....................286
2.8 Removal of Solenoid Valve and Shunt.................................................287
2.9 Removal of Compressor.......................................................................288
Removal Procedure
249
Outdoor Unit (80 / 90 Class)
SiEBE12-625
1. Outdoor Unit (80 / 90 Class)
1.1
Removal of Outer Panels
Procedure
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Warning
Points
External appearance.
Handle
„ Remove the piping in the
backward direction.
Outdoor air
thermistor
Piping connection slot
2
250
Remove 11 screws of
the top panel.
Removal Procedure
SiEBE12-625
Procedure
Step
3
Outdoor Unit (80 / 90 Class)
Points
Unscrew 3 screws of
the right panel, slide it
downwards and release
the tabs to remove.
Right panel
(Main unit side)
Tabs
(Right panel side)
(R2211)
4
The figure shows the
view of piping
connections.
PC board
for servicing
Servicing port
for gas pipe
Servicing port
for fluid pipe
A port
B port
Insects
stopper
shield
C port
D port
(R2212)
5
Unscrew 1 screw of the
front right panel, slide it
downwards and release
the tabs to remove.
Front right panel
Tabs
Removal Procedure
251
Outdoor Unit (80 / 90 Class)
Procedure
Step
6
Unscrew 3 screws of
the front panel to
remove.
7
Remove 4 screws of
the discharge outlet
grill.
8
Slide the discharge
outlet grill upwards and
release 6 tabs to
remove.
252
SiEBE12-625
Points
Removal Procedure
SiEBE12-625
1.2
Outdoor Unit (80 / 90 Class)
Removal of Propeller Fans
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
„ Remove the discharge
outlet grill
1 To take off propeller
fan, remove the
washer-fitted nut M8.
Points
D cut
Washer-fitted nut M8
2
„ For reassembling, align
mark of propeller fan with
D-cut section of motor shaft.
Remove the propeller
fan.
„ Mount the propeller fan while
positioning
mark to the
top.
mark
Removal Procedure
253
Outdoor Unit (80 / 90 Class)
1.3
SiEBE12-625
Removal of Electrical Box
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
„ Remove the outer panels
such as top and front
panels.
1 The figure shows the
right side view.
PC board for servicing
A port
Points
„ Match the colors of the tie
wires to A, B, C and D ports
as follows.
(1) - Black Power
(2) - White Power
(3) - Red
Transmission
Power terminal board
(L) - White
(N) - Black
B port
Earth terminal
screw
C port
„ Wires are fixed to the
terminal board with screws.
D port
Wiring fixture
1. Remove the tie wire.
1 Loosen the terminal
board screws, and
remove the wires at A
and B ports.
2
254
Open the terminal
board cover, and
remove the wires at C
and D ports.
„ When reassembling,
reconnect the wires to C and
D ports.
Terminal
board cover
Removal Procedure
SiEBE12-625
Outdoor Unit (80 / 90 Class)
Procedure
Step
3
Remove the earth wire.
4
Remove 1 screw of the
terminal board.
5
Release the tab on the
top right of the terminal
board.
6
Pull out the terminal
board and open it.
Points
„ Glass tube fuse and varistor
cannot be replaced
individually because leadfree soldering is provided.
Glass tube fuse (Soldered)
Varister
Removal Procedure
255
Outdoor Unit (80 / 90 Class)
SiEBE12-625
Procedure
Step
Points
2. Remove each wire harness
1
Disconnect 4
connectors of the
electronic expansion
valve lead wires.
S20
white
S21
red
S22
blue
S23
yellow
Connector
S20 (White)
S21 (Red)
S22 (Blue)
S23 (Yellow)
Electronic
expansion
valve No.
EVA
EVB
EVC
EVD
Harness
length
630
730
825
940
„ When reconnecting, make
sure to match the wire to the
correct connector.
2
Remove the four way
valve connector S80.
3
Remove the connector
S93 for liquid pipe
thermistor.
256
Removal Procedure
SiEBE12-625
Outdoor Unit (80 / 90 Class)
Procedure
Step
4
Remove the connector
S92 for gas pipe
thermistor.
5
Remove the connector
S90 for thermistor.
„ Outdoor air
thermistor (Blue)
„ Discharge pipe
thermistor (Black)
„ Heat exchanger
thermistor (Gray)
6
Remove the overload
relay connector S40.
7
Remove the reactor
lead wire.
Points
Reactor
Removal Procedure
257
Outdoor Unit (80 / 90 Class)
Procedure
Step
8
SiEBE12-625
Points
Remove the relay
connector for
compressor.
Relay connector
for compressor
9
Remove the electrical
box cover.
Electrical box cover
10
Disconnect the fan
motor connector.
11
Remove the discharge
pipe thermistor.
258
Removal Procedure
SiEBE12-625
Procedure
Step
12
Outdoor Unit (80 / 90 Class)
Take off the thermistor
presser spring, and
remove the thermistor.
Points
„ Place the thermistor so that
its end comes up to the end
of the presser spring.
Thermistor presser spring
„ Be careful not to lose the
presser spring for the
discharge pipe thermistor.
Discharge pipe
thermistor
3. Removing the electrical
box
1 Remove 2 screws of
the electrical box.
2
Turn the electrical box
up side down halfway,
and disconnect the
thermistor lead wire
from the hook.
Hook
Removal Procedure
259
Outdoor Unit (80 / 90 Class)
Procedure
Step
3
Remove the outdoor air
thermistor lead wire
from the groove.
4
Remove each wire
harness, and dismount
the electrical box by
lifting it.
260
SiEBE12-625
Points
Electrical box
Removal Procedure
SiEBE12-625
1.4
Outdoor Unit (80 / 90 Class)
Removal of PCB
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
1. Removing the controller
PCB
1 Release the tab of the
electrical box, and open
the terminal board.
Tab
2
Disconnect each
connector of the
terminal board.
3
Unscrew 1 screw and
release two tabs to
remove the PCB
Tabs
Base bar
Removal Procedure
261
Outdoor Unit (80 / 90 Class)
Procedure
Step
4
Lift the PCB at the
terminal board side.
5
Disconnect each wire
harness connector
linked to the inverter
PCB.
262
SiEBE12-625
Points
Removal Procedure
SiEBE12-625
Outdoor Unit (80 / 90 Class)
Procedure
Step
6
Points
The figure shows the
controller PCB.
S93
S92
S90
S80
S23
S22
S21
S20
S40
Rectifier
stack
S31
S71
S33
S20: Electronic expansion valve
coil A port
S21: Electronic expansion valve
coil B port
S22: Electronic expansion valve
coil C port
S23: Electronic expansion valve
coil D port
S31: To CN14 (Pin 9)
S32: To CN11 (Pin 5)
S33: To S34 (Pin 10)
S40: Overload relay
S71: To S72 (Pin 8)
S80: Four way valve coil
S90: Thermistor (Outdoor air,
heat exchanger, and
discharge pipe)
S92: Gas pipe thermistor
S93: Liquid pipe thermistor
S32
2. Removing the service
monitor PCB
1 Remove the service
monitor PCB by
releasing its tab.
Priority-room setting (SW4)
Service monitor
LED A
LED 1
LED 2
LED 3
LED 4
Wiring error check (SW3)
Forced operation (SW1)
Tab
Night quiet mode (SW5)
Cooling / heating mode lock
(SW2)
3. Removing the inverter
PCB
1 Remove the 9 screws
of the inverter PCB.
Removal Procedure
Fuse cover
Glass tube fuse (3A)
263
Outdoor Unit (80 / 90 Class)
1.5
SiEBE12-625
Removal of Fan Motor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
„ Remove the outer panels.
1 Remove the fan motor
lead wire connector
S70.
S70
2
Remove the propeller
fans.
„ For reassembling, align
mark of propeller fan with
D-cut section of motor shaft.
„ Mount the fan motor so as to
position Q mark on the top.
Washer-fitted nut M8
3
264
Remove 2 screws of
the fan motor mount.
Removal Procedure
SiEBE12-625
Outdoor Unit (80 / 90 Class)
Procedure
Step
4
Remove 4 screws of
the fan motor.
5
Cut the wrapper fixing
the lead wire.
Points
„ When reassembling, fix the
lead wire to avoid contact
with the propeller fan.
6
Remove the fan motor.
Removal Procedure
265
Outdoor Unit (80 / 90 Class)
1.6
Removal of Electronic Expansion Valve and Thermistor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
SiEBE12-625
Remove each wire
harness.
Points
„ Place the thermistor so that
its end comes up to the end
of the presser spring.
„ Be careful not to lose the
presser spring for the
discharge pipe thermistor.
2
Take off the putty, and
remove each
thermistor.
S90:
„ Outdoor air thermistor (Blue)
„ Heat exchanger thermistor
(Gray)
„ Discharge pipe thermistor
(Black)
S92: Gas pipe thermistor
„ Room A (Black)
„ Room B (Gray)
„ Room C (Brown)
„ Room D (Red)
3
266
Remove the electronic
expansion valve coil.
S93: Liquid pipe thermistor
„ Room A (Black)
„ Room B (Gray)
„ Room C (Yellow)
„ Room D (Blue)
Removal Procedure
SiEBE12-625
1.7
Removal of Sound Blanket and Reactor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Outdoor Unit (80 / 90 Class)
Points
Release the clip fixing
the compressor lead
wire.
Clip
2
„ The partition board is not
removable as it is fixed with
the fitting screw in the rear
bottom.
Remove 2 screws of
the partition board, and
move the board
leftward.
Partition board
fitting screw
3
„ Carefully remove the sound
blanket, which is easily torn
in the piping section.
Remove the sound
blanket (outer).
Sound blanket
(outer)
Removal Procedure
267
Outdoor Unit (80 / 90 Class)
Procedure
Step
4
SiEBE12-625
Points
„ Carefully remove the sound
blanket, which is easily torn
in the piping section.
Remove the sound
blanket (top).
Sound blanket
(top)
5
Remove the sound
blanket (inner).
Sound blanket
(inner)
6
268
Remove 1 screw of the
reactor.
Removal Procedure
SiEBE12-625
1.8
Outdoor Unit (80 / 90 Class)
Removal of Shunt
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Remove 6 screws of
the tie wire presser
plate.
2
Remove 4 screws of
the right side panel.
Points
„ Fasten the rubber packing
with double-faced adhesive
tape when mounting.
Rubber
packing
Tie wire pressure plate
Right side panel
3
Remove the putty.
Brazed points
Shunt
Putty
Caution
Be careful not to get yourself
burnt with the pipes and other
parts that are heated by the gas
welding rod.
„ Before taking this
procedure, make sure
there is no refrigerant gas
left in the refrigerant
pipes.
4 Disconnect the 5
brazed points of the
shunt.
Removal Procedure
Warning
If refrigerant gas leaks during
the job, ventilate the room.
(Bear in mind that if the
refrigerant gas is exposed to
open flames, noxious gas may
be generated.)
269
Outdoor Unit (80 / 90 Class)
1.9
SiEBE12-625
Removal of Solenoid Valve and Four Way Valve
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
„ Remove the outer panels.
1. Removing the solenoid
valve
1 Remove 1 screw of the
solenoid valve coil.
„ Before taking this
procedure, make sure
there is no refrigerant gas
left in the refrigerant
pipes.
Caution
Be careful not to get yourself
burnt with the pipes and other
parts that are heated by the gas
welding rod.
2
Disconnect the 2
brazed points (a) and
(b) in this order.
Warning
If refrigerant gas leaks during
the job, ventilate the room.
(Bear in mind that if the
refrigerant gas is exposed to
open flames, noxious gas may
be generated.)
2. Removing the four way
valve
1 Remove 1 screw of the
four way valve coil.
270
Reassembling precautions
Wrap the solenoid valve body
with wet cloth. Splash water
over the cloth before it is dried
to prevent the valve from being
overheated.
Removal Procedure
SiEBE12-625
Procedure
Step
„ Before taking this
procedure, make sure
there is no refrigerant gas
left in the refrigerant
pipes.
2 Place welding
protective sheet or iron
plate around the four
way valve to prevent
the flames of a gas
welding rod from
affecting the valve.
3
4
5
Outdoor Unit (80 / 90 Class)
Heat the 4 brazed
points of the four way
valve. Disconnect the
point (a) first.
Disconnect the points
(b) and (c).
Disconnect the point
(d).
Removal Procedure
Points
Reassembling precautions
1. Use non-oxidizing brazing
method. If nitrogen gas is not
available, braze the parts
speedily.
2. Avoid deterioration of the
gaskets due to carbonization
of oil inside the four way
valve or thermal influence.
For this purpose, wrap the
four way valve with wet
cloth. Splash water over the
cloth against becoming too
hot (keep it below 120°C).
„ In pulling the pipes, be
careful not to over-tighten
them with pliers. The pipes
may get deformed.
If the gas welding machine fails
to remove the four way valve,
take the steps below.
1. Disconnect the brazed pipe
sections that are readily
easy to separate and join
together later.
2. With a small copper tube
cutter, cut off the internal
pipes to easily take out the
four way valve.
Note:
Never use a hack saw. The
sawdust may come into the
circuit.
271
Outdoor Unit (80 / 90 Class)
SiEBE12-625
1.10 Removal of Compressor
Procedure
Warning
Procedure
Step
1
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Points
Remove the terminal
cover.
U (red)
N
(brown)
Terminal cover
2
V(yellow)
W(blue)
Remove the overload
relay.
Overload relay
Terminal nameplate
„ Be careful to avoid burning
the compressor terminals or
the nameplate.
3
Disconnect the flag
shape terminal.
As precaution, keep the
contents in memorandum.
Fixing
plate
Overheat protector
4
272
There is one nut fixing
the compressor.
Remove the nut with a
spanner.
Removal Procedure
SiEBE12-625
Outdoor Unit (80 / 90 Class)
Procedure
Step
„ Make sure there is no
refrigerant gas left inside
the refrigerant pipes
before starting the job.
„ When heating up the
brazed parts, make sure
to carry out the N2
replacement.
5 Remove the 2 sheets of
putty.
Points
Warning
The compressor's refrigerating
machine oil may catch fire. Have
wet cloth at hand for quickly putting
out the fire.
Warning
If refrigerant gas leaks during the
job, ventilate the room. (Bear in
mind that if the refrigerant gas is
exposed to open flames, noxious
gas may be generated.)
Caution
Be careful not to get yourself burnt
with the pipes and other parts that
are heated by the gas welding rod.
6
Disconnect the brazed
part (a) at discharge
side of the compressor.
7
Disconnect the brazed
part (b) at suction side
of the compressor.
Removal Procedure
273
Outdoor Unit (68 / 75 Class)
SiEBE12-625
2. Outdoor Unit (68 / 75 Class)
2.1
Removal of Outer Panels
Procedure
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
External appearance.
2
Remove 4 screws of
the top panel and 6
screws of the front
panel.
Remove 4 screws of
the discharge outlet
grill.
3
Warning
Points
Top panel
Discharge outlet grill
Front panel
4
Remove 2 screws of
the piping cover.
Piping cover
274
Removal Procedure
SiEBE12-625
2.2
Outdoor Unit (68 / 75 Class)
Removal of Electrical BOX
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
1. Removing the tie wires
1
The figure shows the tie
pipe connections.
Service monitor PCB
Electrical box
A port
B port
C port
Electronic expansion
valve coils
D port
Service port
„ Remove the piping in the
backward direction.
Outdoor air thermistor
Gas pipe
Fluid pipes
2
Remove the terminal
board fitting screw.
Terminal board fitting screw
A port
C port
Power terminal
board
(L) - White
(N) - Black
B port
D port
Earth terminal
screw
„ Match the colours of the tie
wires to A, B, C and D ports
as follows.
(1) - Black Power
(2) - White Power
(3) - Red Transmission
„ Wires are fixed to the
terminal board with screws.
„ Terminal board is made of
integral moulded resin.
Wiring fixture
Removal Procedure
275
Outdoor Unit (68 / 75 Class)
SiEBE12-625
Procedure
Step
3
Pull out the terminal
board to open.
Points
„ Glass tube fuse and varistor
cannot be replaced
individually because leadfree soldering is provided.
Glass tube fuse
Varister
Terminal
board
Screw
2. Remove each wire
harness
1 Disconnect 4
connectors of the
electronic expansion
valve lead wires.
Connector
S20 (White)
S21 (Red)
S22 (Blue)
S23 (Yellow)
Electronic
expansion
valve No.
EVA
EVB
EVC
EVD
Harness
length
630
730
825
940
„ When reconnecting, make
sure to match the wire to the
correct connector.
2
Remove the four way
valve connector S80.
3
Disconnect the
thermistor connector
and the overload relay
connector.
S90 S92 S93
S40
276
S40:Overload relay
S90:Thermistor
(Outdoor air, heat
exchanger, discharge pipe)
S92:Gas pipe thermistor
S93:Liquid pipe thermistor
Removal Procedure
SiEBE12-625
Outdoor Unit (68 / 75 Class)
Procedure
Step
4
Disconnect the
compressor relay
connector.
5
Remove the reactor
lead wire.
Points
3. Removing the wiring
fixture
1 Remove 6 screws of
the wiring fixture.
Wiring fixture
4. Removing the electrical
box.
1 Remove 1 screw of the
electrical box.
Removal Procedure
277
Outdoor Unit (68 / 75 Class)
SiEBE12-625
Procedure
Step
2
Remove 1 screw of the
electrical box.
3
Remove the drip-proof
cover.
Points
Drip-proof cover
4
Disconnect the fan
motor lead wire.
5
Lift up the electrical box
and dismount it.
278
Removal Procedure
SiEBE12-625
2.3
Outdoor Unit (68 / 75 Class)
Removal of PCB
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
1. Removing the controller
PCB
1 Remove 1 screw of the
PCB, and release two
tabs.
Base bar
2
Release the tabs of the
terminal board, and
open the terminal
board.
Tab
3
Disconnect each
connector on the back
of the terminal board.
4
Disconnect the service
monitor PCB connector.
„ Release the tab to remove
the service monitor PCB.
Tab
Removal Procedure
279
Outdoor Unit (68 / 75 Class)
SiEBE12-625
Procedure
Step
5
Lift up the control PCB.
6
Disconnect each wire
harness connector
linked to the control
PCB.
S31 (Pin 9): To CN14
S32 (Pin 5): To CN11
S33 (Pin 10): To S34
S71 (Pin 8): To S72
Points
H1 (yellow)
H2 (blue)
ECN1 (green)
280
Removal Procedure
SiEBE12-625
Outdoor Unit (68 / 75 Class)
Procedure
Step
7
Points
„ Glass tube fuse 3A
The figure shows the
control PCB.
S93
Varistor
S92
S90
FU2
S33
S71
S31
S80
S23
S22
S21
S20
S40 S6
2. Removing the service
monitor PCB
1 The figure shows the
service monitor PCB.
Priority-room setting (SW4)
LED A
Wiring error check (SW3)
LED 1
Forced operation (SW1)
LED 2
Night quiet mode (SW5)
LED 3
LED 4
Cooling / heating mode lock
(SW2)
3. Removing the inverter
PCB.
1 Remove the 7 screws
of the inverter PCB.
Fuse 3A
Removal Procedure
281
Outdoor Unit (68 / 75 Class)
2.4
SiEBE12-625
Removal of Fan Motor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
„ Remove the fan motor
lead wire connector.
1 Remove the propeller
fan by removing the
washer-fitted nut.
Points
„ For reassembling, align
mark of propeller fan with
D-cut section of motor shaft.
„ Mount the propeller fan while
positioning Q mark to the
top.
Washer-fitted nut
2
Remove the fan motor.
Remove 1 screw of the
fan motor mount.
„ When reassembling, fix the
lead wire to avoid contact
with the propeller fan.
3
282
Disconnect the lead
wire by releasing the 2
clamps fixing the wire.
Remove 4 screws of
the fan motor.
Removal Procedure
SiEBE12-625
2.5
Removal of Sound Blanket
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Outdoor Unit (68 / 75 Class)
Points
Remove 5 screws of
the right side panel.
Right side
panel
2
Remove 2 screws of
the partition board, and
remove the board.
3
Remove the sound
blanket (top, outer and
inner).
Carefully remove the sound
blanket, which is easily torn
in the piping section.
Sound blanket (top)
Sound blanket (top inner)
Sound blanket
(inner)
Sound blanket
(outer)
Removal Procedure
283
Outdoor Unit (68 / 75 Class)
2.6
Removal of Four Way Valve Coil, Solenoid Valve Coil,
Electronic Expansion Valve Coil and Thermistor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Remove 1 screw of the
four way valve coil.
2
Remove one screw of
the solenoid valve coil.
3
Remove the electronic
expansion valve coil for
each room.
4
SiEBE12-625
Release the thermistor
presser spring, and
remove the discharge
pipe thermistor.
Points
Thermistor
presser
spring
„ Place the thermistor so that
its end comes up to the end
of the presser spring.
„ Be careful not to lose the
presser spring for the
discharge pipe thermistor.
Thermistor
Pipe
Discharge pipe
thermistor
284
Thermistor
presser
spring
Removal Procedure
SiEBE12-625
Procedure
Step
5
Outdoor Unit (68 / 75 Class)
Take off the putty, and
remove each
thermistor.
Points
„ Place the thermistor so that
its end comes up to the end
of the presser spring.
„ Be careful not to lose the
presser spring for the
discharge pipe thermistor.
Thermistor
Pipe
6
Remove the wire
harness.
Thermistor
presser
spring
S90:
„ Outdoor air thermistor (Blue)
„ Heat exchanger thermistor
(Gray)
„ Discharge pipe thermistor
(Black)
S92: Gas pipe thermistor
„ Room A (Black)
„ Room B (Gray)
„ Room C (Brown)
„ Room D (Red)
S93: Liquid pipe thermistor
„ Room A (Black)
„ Room B (Gray)
„ Room C (Yellow)
„ Room D (Blue)
Removal Procedure
285
Outdoor Unit (68 / 75 Class)
2.7
SiEBE12-625
Removal of Four Way Valve, Solenoid Valve and Shunt
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
Remove 1 screw of the
four way valve coil.
2
Remove 1 screw of the
solenoid valve coil.
„ Before taking this
procedure, make sure
there is no refrigerant gas
left in the refrigerant
pipes.
3 Place welding
protective sheet or iron
plate around the four
way valve to prevent
the flames of a gas
welding rod from
affecting the valve.
Points
Reassembling precautions
1. Use non-oxidizing brazing
method. If nitrogen gas is not
available, braze the parts
speedily.
2. Avoid deterioration of the
gaskets due to carbonization
of oil inside the four way
valve or thermal influence.
For this purpose, wrap the
four way valve with wet
cloth. Splash water over the
cloth against becoming too
hot (keep it below 120°C).
„ In pulling the pipes, be
careful not to over-tighten
them with pliers. The pipes
may get deformed.
If the gas welding machine fails
to remove the four way valve,
take the steps below.
1. Disconnect the brazed pipe
sections that are readily
easy to separate and join
together later.
2. With a small copper tube
cutter, cut off the internal
pipes to easily take out the
four way valve.
Note:
4
5
6
286
Heat the four brazed
points of the four way
valve. Disconnect the
point (a) first.
Disconnect the points
(b) and (c).
Disconnect the point
(d).
Never use a hack saw. The
sawdust may come into the
circuit.
Removal Procedure
SiEBE12-625
2.8
Outdoor Unit (68 / 75 Class)
Removal of Solenoid Valve and Shunt
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
Points
„ Before taking this
procedure, make sure
there is no refrigerant gas
left in the refrigerant
pipes.
1 Disconnect the 2
brazed points (a) and
(b) in this order.
2
Remove the putty of the
shunt.
3
Disconnect the 5
brazed points of the
shunt.
Caution
Be careful not to get yourself
burnt with the pipes and other
parts that are heated by the gas
welding rod.
Warning
If refrigerant gas leaks during
the job, ventilate the room.
(Bear in mind that if the
refrigerant gas is exposed to
open flames, noxious gas may
be generated.)
Reassembling precautions
Wrap the solenoid valve body
with wet cloth. Splash water
over the cloth before it is dried
to prevent the valve from being
overheated.
Brazed part
Brazed
point
Shunt
Putty
Removal Procedure
287
Outdoor Unit (68 / 75 Class)
2.9
Removal of Compressor
Procedure
Warning
Be sure to wait 10 minutes or more after turning off all power supplies
before disassembling work.
Procedure
Step
1
SiEBE12-625
Points
Remove the terminal
cover.
U (red)
N
(brown)
V (yellow)
W (blue)
Terminal nameplate
2
3
Disconnect the
compressor lead wire.
Remove the 2 sheets of
putty.
As precaution, keep the contents
in memorandum.
„ Be careful to avoid burning
the compressor terminals or
the nameplate.
There is one nut fixing
the compressor.
Remove the nut with an
open-end spanner.
„ Make sure there is no
refrigerant gas left inside
the refrigerant pipes
before starting the job.
4
„ When heating up the
brazed parts, make sure
to carry out the N2
replacement.
1 Disconnect the brazed
part (a) at discharge
side of the compressor.
2 Disconnect the brazed
part (b) at suction side
of the compressor.
Warning
The compressor's refrigerating
machine oil may catch fire.
Have wet cloth at hand for
quickly putting out the fire.
Warning
If refrigerant gas leaks during
the job, ventilate the room.
(Bear in mind that if the
refrigerant gas is exposed to
open flames, noxious gas may
be generated.)
Caution
Be careful not to get yourself
burnt with the pipes and other
parts that are heated by the gas
welding rod.
288
Removal Procedure
SiEBE12-625
Part 8
Others
1. Others .................................................................................................290
1.1 Test Run from the Remote Controller ..................................................290
1.2 Jumper Settings ...................................................................................291
Others
289
Others
SiEBE12-625
1. Others
1.1
Test Run from the Remote Controller
For Heat pump
In cooling mode, select the lowest programmable temperature; in heating mode, select the
highest programmable temperature.
„ Trial operation may be disabled in either mode depending on the room temperature.
„ After trial operation is complete, set the temperature to a normal level.
(26°C to 28°C in cooling mode, 20°C to 24°C in heating mode)
„ For protection, the system disables restart operation for 3 minutes after it is turned off.
For Cooling Only
Select the lowest programmable temperature.
„ Trial operation in cooling mode may be disabled depending on the room temperature.
Use the remote control for trial operation as described below.
„ After trial operation is complete, set the temperature to a normal level (26°C to 28°C).
„ For protection, the machine disables restart operation for 3 minutes after it is turned off.
Trial Operation and Testing
1. Measure the supply voltage and make sure that it falls in the specified range.
2. Trial operation should be carried out in either cooling or heating mode.
3. Carry out the test operation in accordance with the Operation Manual to ensure that all
functions and parts, such as louver movement, are working properly.
„ The air conditioner requires a small amount of power in its standby mode. If the system is
not to be used for some time after installation, shut off the circuit breaker to eliminate
unnecessary power consumption.
„ If the circuit breaker trips to shut off the power to the air conditioner, the system will restore
the original operation mode when the circuit breaker is opened again.
Trial operation from Remote Controller
(1) Press ON/OFF button to turn on the system.
(2) Simultaneously press center of TEMP button and MODE buttons.
(3) Press MODE button twice.
(“T” will appear on the display to indicate that Trial Operation mode is selected.)
(4) Trial run mode terminates in approx. 30 minutes and switches into normal mode. To quit a
trial operation, press ON/OFF button.
(3)
(2)
ON/OFF
TEMP
(3)
290
MODE
(1) (4)
(R4294)
Others
SiEBE12-625
1.2
Others
Jumper Settings
1.2.1 When Two Units are Installed in One Room
When two indoor units are installed in one room, the two wireless remote controllers can be set
for different addresses.
How to set the different addresses
„ Control PCB of the indoor unit
(1) Remove the electrical box.
(2) Cut the address jumper JA on the control PCB.
„ Wireless remote controller
(1) Slide the front cover and take it off.
(2) Cut the address jumper J4.
JA
ADDRESS
J4
JA ADDRESS
J4 ADDRESS
EXIST
CUT
EXIST
CUT
1
2
1
2
(R4417)
(R4418)
1.2.2 Jumper Setting
Jumper
(On indoor PCB)
JC
JB
Others
Function
Power failure
recovery function
When connected
(factory set)
Auto start
When cut
Unit does not resume operation
after recovering from a power
failure. Timer ON-OFF settings
are cleared.
Fan speed setting
Fan speed setting ; Fan rpm is set to “0”
when compressor is Remote controller
<Fan stop>
OFF on thermostat. setting
(effective only at
cooling operation)
291
Others
SiEBE12-625
1.2.3 Adjusting the Angle of the Intelligent Eye Sensor
FTK(X)S20-35C
„ Once installation of the indoor unit is complete, adjust the angle of the Intelligent eye sensor
to ensure the detection area properly covers the room.
(Adjustable angle : 15° to right and left of center)
15°
15°
Intelligent-eye
sensor
„ Gently push and slide the sensor to adjust the angle. Aim so that the sensor is pointing to the
center of the room, or to the part of the room that is most frequently used.
Moving the sensor to the left
Moving the sensor to the right
„ After adjusting the angle, gently wipe the sensor with a clean cloth, being careful not to
scratch the sensor.
Caution
292
„ Do not hit or violently push the Intelligent eye sensor. This can lead to damage and
malfunction.
„ Do not place large objects near the sensor. Also keep heating units or humidifiers outside
the sensor’s detection area.
Others
SiEBE12-625
Part 9
Appendix
1. Piping Diagrams..................................................................................294
1.1 Indoor Units ..........................................................................................294
1.2 Outdoor Units .......................................................................................300
2. Wiring Diagrams..................................................................................302
2.1 Indoor Units ..........................................................................................302
2.2 Outdoor Units .......................................................................................306
Appendix
293
Piping Diagrams
SiEBE12-625
1. Piping Diagrams
1.1
Indoor Units
1.1.1 Wall Mounted Type
FTKS20/25/35D3VMW(L)
FTXS20/25/35D3VMW(L)
INDOOR UNIT
Maffler assy
7.0CuT
INDOOR UNIT
Heat exchanger
Maffler assy
7.0CuT Heat
Thermistor
on heat exch.
6.4CuT
6.4CuT
Field piping
Cross flow fan
(6.4CuT)
M
Thermistor
on heat exch.
6.4CuT
6.4CuT
Cross flow fan
Field piping
(6.4CuT)
M
Fan motor
Field piping
exchanger
6.4CuT
7.9CuT
7.9CuT
6.4CuT
Fan motor
9.5CuT
Field piping
(9.5CuT)
9.5CuT
(9.5CuT)
Refrigerant flow
cooling
Refrigerant flow
cooling
heating
4D047912E
4D050757A
FTKS20/25/35CAVMB
FTXS20/25/35CAVMB
INDOOR UNIT
INDOOR UNIT
Heat exchanger
7.0CuT
7.0CuT
6.4CuT
6.4CuT
Thermistor
on heat exch.
7.9CuT
7.9CuT
Heat exchanger
6.4CuT
Thermistor
on heat exch.
Field piping
(6.4CuT)
Cross flow fan
Field piping
(6.4CuT)
M
Field piping
9.5CuT
M
9.5CuT
(9.5CuT)
(9.5CuT)
Refrigerant flow
cooling
heating
Refrigerant flow
cooling
4D033698E
294
Cross flow fan
Fan motor
Fan motor
Field piping
6.4CuT
6.4CuT
6.4CuT
4D049319A
Appendix
SiEBE12-625
Piping Diagrams
FTKS50D2V1W(L)
FTXS50D2V1W(L)
INDOOR UNIT
Maffler assy
Heat exchanger
INDOOR UNIT
7.0CuT
Maffler assy
6.4CuT
Thermistor
on heat exch.
6.4CuT
6.4CuT
Cross flow fan
Field piping
(6.4CuT)
M
Field piping
Fan motor
(6.4CuT)
Field piping
Heat exchanger
7.0CuT
7.9CuT
7.9CuT
6.4CuT
9.5CuT
Thermistor
on heat exch.
6.4CuT
6.4CuT
Cross flow fan
M
Fan motor
(12.7CuT)
Field piping
Refrigerant flow
cooling
9.5CuT
(12.7CuT)
Refrigerant flow
cooling
heating
4D051577
FTK(X)S50/60EV1B
4D047913D
FTKS71EV1B, FTKS71BAV1B
INDOOR UNIT
INDOOR UNIT
(7.9CuT)
(7.9CuT)
Heat exchanger
Heat exchanger
Thermistor
on heat exch.
Field piping
Cross flow fan
(6.4CuT)
M
Field piping
(12.7CuT)
Thermistor
on heat exch.
Field piping
Fan motor
(6.4CuT)
12.7CuT
Field piping
(15.9CuT)
Refrigerant flow
cooling
heating
M
Fan motor
(12.7CuT)
Refrigerant flow
cooling
4D040081M
Appendix
Cross flow fan
4D050919B
295
Piping Diagrams
SiEBE12-625
FTXS71EV1B, FTXS71BAVMB
FTXG25/35EV1BW(S)
INDOOR UNIT
INDOOR UNIT
7.0CuT
7.9CuT
7.0CuT
7.0CuT
Heat exchanger
Thermistor
on heat exch.
Field piping
Field piping
Cross flow fan
(6.4CuT)
Field piping
(15.9CuT)
Heat exchanger
(6.4CuT)
Thermistor
on heat exch.
7.0CuT
7.0CuT
Cross flow fan
M
Fan motor
M
Field piping
Fan motor
9.5CuT
(9.5CuT)
(12.7CuT)
Refrigerant flow
cooling
heating
Refrigerant flow
cooling
heating
4D040082M
4D045301B
CTXG50EV1BW(S)
INDOOR UNIT
7.0CuT
Heat exchanger
7.0CuT
7.0CuT
Thermistor
on heat exch.
7.0CuT
7.0CuT
Field piping
(6.4CuT)
Field piping
Cross flow fan
M
Fan motor
9.5CuT
(12.7CuT)
Refrigerant flow
cooling
heating
4D050924
296
Appendix
SiEBE12-625
Piping Diagrams
1.1.2 Duct Connected Type
FDK(X)S25/35EAVMB, FDK(X)S50/60CVMB, FDK(X)S25/35CAVMB
UNIT
INDOORINDOOR
UNIT
(6.4CuT)
Heat exchanger
Thermistor
on heat
exch.
Field piping
(6.4CuT)
Sirocco fan
M
Fan motor
( CuT)
Field piping
( CuT)
CDXS25CVMB
CDKS25CVMB
CDXS35CVMB
CDKS35CVMB
CDXS25CVMA
CDXS35CVMA
FDXS25CVMB
FDXS35CVMB
FDXS35CVMA
FDXS25EAVMB
FDXS35EAVMB
FDKS25CVMB
FDKS35CVMB
FDKS25EAVMB
FDKS35EAVMB
CDKS25CVMA
CDKS35CVMA
CDXS25DVMT
CDXS35DVMT
CDKS25DVMT
CDKS35DVMT
FDXS25CAVMB
FDXS35CAVMB
FDKS25CAVMB
FDKS35CAVMB
CDXS25EAVMA
CDXS35EAVMA
CDKS25EAVMA
CDKS35EAVMA
CDXS25EAVMT
CDXS35EAVMT
CDKS25EAVMT
CDKS35EAVMT
CDXS25EV2C
CDXS35EV2C
FDXS25CVMA
CDXS50CVMB
CDKS50CVMB
CDXS60CVMB
CDKS60CVMB
CDXS50CVMA
CDXS60CVMA
CDKS50CVMA
CDKS60CVMA
CDXS50DVMT
CDXS60DVMT
CDKS50DVMT
CDKS60DVMT
FDXS50CVMB
FDXS60CVMB
FDKS50CVMB
FDKS60CVMB
CDXS50EV2C
CDXS60EV2C
FDXS50CVMA
FDXS60CVMA
9.5
Refrigerant flow
cooling
heating
12.7
4D045449J
1.1.3 Floor / Ceiling Suspended Dual Type
FLKS25/35BAVMB
FLKS50/60BAVMB
INDOOR UNIT
INDOOR UNIT
(9.5CuT)
(6.4CuT)
Heat exchanger
Heat exchanger
Field piping
Field piping
(6.4CuT)
Sirocco fan
Thermistor
on heat
exch.
(6.4CuT)
M
Fan motor
M
Fan motor
Field piping
Field piping
(12.7CuT)
(12.7CuT)
(9.5CuT)
(9.5CuT)
Refrigerant flow
cooling
Refrigerant flow
cooling
4D034012E
Appendix
Sirocco fan
Thermistor
on heat
exch.
4D048723A
297
Piping Diagrams
SiEBE12-625
FLXS25/35BAVMB
FLXS50/60BAVMB
INDOOR UNIT
INDOOR UNIT
(6.4CuT)
(9.5CuT)
Heat exchanger
Heat exchanger
Field piping
(6.4CuT)
Sirocco fan
Thermistor
on heat
exch.
Field piping
(6.4CuT)
Sirocco fan
M
M
Fan motor
Fan motor
Field piping
(9.5CuT)
Field piping
Thermistor
on heat
exch.
(9.5CuT)
(9.5CuT)
(12.7CuT)
Refrigerant flow
cooling
heating
Refrigerant flow
cooling
heating
4D048724A
4D048722A
1.1.4 Floor Standing Type
FVKS25/35BAVMB
FVXS25/35BAVMB
INDOOR UNIT
INDOOR UNIT
Heat exchanger
M
Cross flow fan Fan motor
M
Cross flow fan Fan motor
Thermistor
on heat
exch.
7.0CuT
Cross flow fan Fan motor
(6.4CuT)
Single union joint
7.0CuT
Single union joint
Field piping
9.5CuT
(9.5CuT)
Single union joint
Refrigerant flow
cooling
9.5CuT
Single union joint
Refrigerant flow
cooling
heating
4D050798
298
Thermistor
on heat
exch.
7.0CuT
Field piping
Field piping
(9.5CuT)
M
Cross flow fan Fan motor
M
7.0CuT
Field piping
(6.4CuT)
7.9CuT
7.9CuT
Heat exchanger
4D034714C
Appendix
SiEBE12-625
Piping Diagrams
FVKS50BAVMB
FVXS50BAVMB
INDOOR UNIT
7.0CuT
4.8CuT
4.8CuT
M
Cross flow fan
Fan motor
Muffler
Field piping
(6.4CuT)
Muffler
M
Cross flow fan
Field piping
Fan motor
Thermistor
on heat
exch.
7.0CuT
4.8CuT
4.8CuT
Cross flow fan Fan motor
Muffler
Field piping
7.0CuT
Cross flow fan Fan motor
(6.4CuT)
Field piping
9.5CuT
Heat exchanger
M
M
7.0CuT
7.0CuT
(12.7CuT)
Thermistor
on heat
exch.
7.0CuT
7.0CuT
7.0CuT
9.5CuT
(12.7CuT)
Refrigerant flow
cooling
Refrigerant flow
cooling
heating
4D050804
Appendix
9.5CuT
9.5CuT
Muffler
INDOOR UNIT
Heat exchanger
4D020911D
299
Piping Diagrams
1.2
SiEBE12-625
Outdoor Units
1.2.1 Cooling Only
4MKS75E2(3)V1B
OUTDOOR UNIT
HEAT EXCHANGER
Outdoor temperature
thermistor(DOA)
HEADER
9.5CuT
MOTOR OPERATED VALVE Liquid Pipe
Thermistor(DLA)
EVA
6.4CuT
9.5CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLB)
EVB
6.4CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLC)
EVC
6.4CuT
FILTER
HEAT EXCHANGER
THERMISTOR(DE)
DISTRIBUTOR
Liquid line
stop valve
CAPILLARY TUBE
M
DC FAN MOTOR
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLD)
EVD
6.4CuT
FILTER
ROOM A
(6.4 CuT)
ROOM B
(6.4 CuT)
Field
piping
liquid
ROOM C
(6.4 CuT)
ROOM D
(6.4 CuT)
PROPELLER FAN
7.9CuT
HEADER
12.7CuT
12.7CuT
12.7CuT
Discharge pipe
thermistor(DO)
12.7CuT
Gas line
stop valve
Refrigerant flow
cooling
COMPRESSOR
12.7CuT
ACCUMULATOR
12.7CuT
Gas pipe thermistor(DGA)
ROOM A
(9.5 CuT)
Gas pipe thermistor(DGB)
ROOM B
(9.5 CuT)
Gas pipe thermistor(DGC)
ROOM C
(12.7 CuT)
Field
piping
gas
Gas pipe thermistor(DGD)
ROOM D
(15.9 CuT)
ACCUMULATOR
3D034513F
4MKS90DAVMB
OUTDOOR UNIT
HEAT EXCHANGER
Outdoor temperature
thermistor(DOA)
HEADER
7.9CuT
7.9CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLB)
EV B
7.9CuT
7.9CuT
7.9CuT
HEAT EXCHANGER
THERMISTOR(DE)
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLC)
EV C
7.9CuT
9.5CuT
9.5CuT
9.5CuT
7.9CuT
7.9CuT
MOTOR OPERATED VALVE Liquid Pipe
Thermistor(DLA)
EV A
7.9CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
EV D
Thermistor(DLD)
7.9CuT
Liquid line
stop valve
DISTRIBUTOR
CAPILLARY TUBE
DC FAN MOTOR
FILTER
M
9.5CuT
ROOM A
(6.4CuT)
ROOM B
(6.4CuT)
ROOM C
(6.4CuT)
Field
piping
liquid
ROOM D
(6.4CuT)
FILTER
PROPELLER FAN
HEADER
7.9CuT
12.7CuT
12.7CuT
12.7CuT
12.7CuT
Refrigerant flow
cooling
COMPRESSOR
12.7CuT
Discharge pipe
thermistor(DO)
ACCUMULATOR
12.7CuT
Gas line
stop valve
ACCUMULATOR
12.7CuT
Gas pipe thermistor(DGA)
ROOM A
(9.5CuT)
Gas pipe thermistor(DGB)
ROOM B
(12.7CuT)
Gas pipe thermistor(DGC)
ROOM C
(15.9CuT)
Field
piping
gas
Gas pipe thermistor(DGD)
ROOM D
(15.9CuT)
12.7CuT
3D034481D
300
Appendix
SiEBE12-625
Piping Diagrams
1.2.2 Heat Pump
4MXS68E2(3)V1B
OUTDOOR UNIT
Outdoor temperature
thermistor(DOA)
HEAT EXCHANGER
HEADER
HEADER
6.4CuT
9.5CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLB)
EVB
6.4CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLC)
EVC
6.4CuT
FILTER
HEAT EXCHANGER
THERMISTOR(DE)
DISTRIBUTOR SV
CAPILLARY TUBE
6.4CuT
M
DC FAN MOTOR
MOTOR OPERATED VALVE Liquid Pipe
Thermistor(DLA)
EVA
6.4CuT
DEFROST
SOLENOID
VALVE
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLD)
EVD
6.4CuT
Liquid line
stop valve
FILTER
ROOM B
(6.4 CuT)
Field
piping
liquid
ROOM C
(6.4 CuT)
ROOM D
(6.4 CuT)
12.7CuT
PROPELLER FAN
12.7CuT
12.7CuT
HEADER
12.7CuT
REVERSING
SOLENOID
VALVE
MUFFLER
12.7CuT
Gas pipe thermistor(DGA)
ROOM A
(9.5 CuT)
Gas pipe thermistor(DGB)
ROOM B
(9.5 CuT)
Gas pipe thermistor(DGC)
12.7CuT
Gas line
stop valve
ACCUMULATOR
COMPRESSOR
12.7CuT
12.7CuT
7.9CuT
Discharge pipe
thermistor(DO)
Refrigerant flow
cooling
heating
ROOM A
(6.4 CuT)
12.7CuT
ROOM C
(12.7 CuT)
Field
piping
gas
Gas pipe thermistor(DGD)
ROOM D
(12.7 CuT)
ACCUMULATOR
3D034511G
4MXS80DAVMB
OUTDOOR UNIT
Outdoor temperature
thermistor(DOA)
RECEIVER
7.9CuT
6.4CuT
HEAT EXCHANGER
THERMISTOR(DE)
DISTRIBUTOR
SV
CAPILLARY TUBE
M
PROPELLER FAN
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLC)
EV C
7.9CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLD)
EV D
7.9CuT
Liquid line
SOLENOID stop valve
VALVE
9.5CuT
FILTER
12.7CuT
Refrigerant flow
cooling
heating
HEADER
12.7CuT
12.7CuT
12.7CuT
7.9CuT
12.7CuT
12.7CuT
12.7CuT
Gas line
stop valve
COMPRESSOR
ROOM B
(6.4CuT)
ROOM C
(6.4CuT)
Field
piping
liquid
ROOM D
(6.4CuT)
FILTER
7.9CuT
MUFFLER
Discharge pipe
thermistor(DO)
ROOM A
(6.4CuT)
12.7CuT
4-WAY
VALVE
12.7CuT
MOTOR OPERATED VALVE Liquid Pipe
Thermistor(DLA)
EV A
7.9CuT
MOTOR OPERATED VALVE Liquid Pipe FILTER
Thermistor(DLB)
EV B
7.9CuT
6.4CuT
DC FAN MOTOR
HEADER
7.9CuT
7.9CuT
7.9CuT
9.5CuT
12.7CuT
7.9CuT
7.9CuT
7.9CuT
7.9CuT
7.9CuT
7.9CuT
7.9CuT
7.9CuT
9.5CuT
HEAT EXCHANGER
HEADER
ACCUMULATOR
ACCUMULATOR
12.7CuT
Gas pipe thermistor(DGA)
ROOM A
(9.5CuT)
Gas pipe thermistor(DGB)
ROOM B
(9.5CuT)
Gas pipe thermistor(DGC)
ROOM C
(12.7CuT)
Field
piping
gas
Gas pipe thermistor(DGD)
ROOM D
(15.9CuT)
12.7CuT
3D034480D
Appendix
301
Wiring Diagrams
SiEBE12-625
2. Wiring Diagrams
2.1
Indoor Units
2.1.1 Wall Mounted Type
FTK(X)S20/25/35D3VMW(L)
FIELD WIRING.
PCB3
S27
PCB1
S26
~
LED1
H1P
H1
F1U
~
RECTIFIER
1
X1M
2
BLK
1
3
WHT
2
RED
3
3.15A
V1
H2
LED2
H2P
LED3
H3P
H3
Transmission
circuit
CAUTION
GRN/
YLW
Note that operation will
restart automatically if
the main power supply is
turned off and then back on
again.
FG
S1W
7 S1
S21
t°
HA
R1T
S36
1
S35
Intelligent eye
sensor
S28
S32
PCB2
t°
S29
Infrared
remote
control
1
S6
FG
F1U
H1P~H3P
M1F
M1S
PCB1~PCB4
R1T, R2T
S1~S38
S1W
X1M
M
M1F
5
RED
ORG
YLW
PNK
BLU
PCB4
RED
BLU
BRN
ORG
WHT
R2T
Signal
receiver
INDOOR
M
OUTDOOR
Frame ground
Fuse
Pilot lamp
Fan motor
Swing motor
Printed circuit board
Thermistor
Connector
Operation switch
Terminal strip
Protective earth
M1S
3D051268A
FTK(X)S20/25/35CAVMB
PCB3
S36
S35
PCB1
H1
Intelligent eye
sensor
Fu
3.15A
S27
PCB2
(Terminal for
centralized control)
S26
C70
LED1 LED2 LED3
S21
H1P H2P H3P
S1W
Signal
receiver
t°
t°
140°C
M1F
M
M1S
FIELD WIRING.
CAUTION
1
t°
R2T
H3
Note that operation will
restart automatically if
the main power supply is
turned off and then back on
again.
M
S6
R1T
Infrared
remote
control
Transmission
circuit
S1
S7
S32
BLK
WHT
RED
GRN/YLW
H2
1
2 ?
3
outdoor
X1M
1
2
3
indoor
: Protective earth
C70 : Running capacitor
FU : Fuse
H1P~H3P
M1F
M1S
PCB1~PCB3
R1T~R2T
S1~S36
S1W
X1M
:
:
:
:
:
:
:
:
Pilot lamp
Fan motor
Swing motor
Printed circuit board
Thermistor
Connector
Operation switch
Terminal strip
3D033599G
302
Appendix
SiEBE12-625
Wiring Diagrams
FTK(X)S50D2V1W(L)
FIELD WIRING.
PCB3
S27
S26
PCB1
~
LED1
H1P
RECTIFIER
H1
F1U
~
1
3.15A
V1
H2
LED2
H2P
LED3
H3P
2
BLK
1
3
WHT
2
RED
3
OUTDOOR
GRN/
YLW
H3
Transmission
circuit
X1M
CAUTION
Note that operation will
restart automatically if
the main power supply is
turned off and then back on
again.
FG
S1W
7
S21
S1
RED
t°
HA
R1T
BLU
BRN
ORG
WHT
1
S36
M1F
S35
Intelligent eye
sensor
S32
S28
1
X41A
PCB2
FG
F1U
H1P~H3P
M1F
M1S
PCB1~PCB4
R1T, R2T
S1~S38, X41A
S1W
X1M
5
S6
RED
ORG
YLW
PNK
BLU
PCB4
M
S29
Infrared
remote
control
t°
Signal
receiver
INDOOR
M
R2T
Frame ground
Fuse
Pilot lamp
Fan motor
Swing motor
Printed circuit board
Thermistor
Connector
Operation switch
Terminal strip
Protective earth
M1S
3D051652
FTK(X)S50/60/71EV1B, FTK(X)S71BAVMB
FIELD WIRING.
PCB3
S27
S26
PCB1
H1
~
~
RECTIFIER
1
Fu
3.15A
H2
t°
R1T
S38
2
BLK
1
3
WHT
2
RED 3
GRN
/
YLW
H3
Transmission
circuit
X1M
FG
PCB4
S37
S21
7
S1
RED
OUTDOOR
CAUTION
Note that operation will
restart automatically if the
main power supply is
turned off and then back
on again.
LED1 LED2 LED3
S36
1
S35
Intelligent eye
sensor
S28
PCB2
Infrared
remote
control
Signal
receiver
S1W
S32
t°
S29
1
S6
5
1
S8
M
M1F
6
BRN
RED
ORG
YLW
PNK
BLU
PCB5
Appendix
BLU
BRN
ORG
WHT
H2P H3P
RED
ORG
YLW
PNK
BLU
H1P
INDOOR
R2T
M
M1S
M
M2S
FG
: Frame ground
Fu
: Fuse
H1 ~ H3
: Harness
H1P ~ H3P :Pilot lamp
M1F
: Fan motor
M1S, M2S
: Swing motor
PCB1~ PCB5 : Printed circuit board
R1T, R2T
:Thermistor
S1 ~ S38
S1W
: Connector
: Operation switch
X1M
: Terminal strip
:Protection earth
3D038530K
303
Wiring Diagrams
SiEBE12-625
FTXG25/35EV1BW(S), CTXG50EV1BW(S)
PCB2
Signal LED4 LED3 LED2
receiver
PCB3
t°
S47
FIELD WIRING.
GRN / YLW
S1W
R2T
E2
E1
X1M
3
2
1
FG
PCB1
S36
GRN / YLW
H4P H3P H2P
Infrared
remote
control
Transmission
circuit
S46
S36
RED
WHT
BLK
H3
Intelligent
eye sensor
H2
3
2
1
CAUTION
H1B
Note that operation will
restart automatically if
the main power supply is
turned off and then back
on again.
3.15A
F1U
~
~
RECTIFIER
t°
R1T
S49
7
RED
ORG
YLW
PNK
BLU
RED
ORG
YLW
PNK
BLU
BLK
WHT
M
S2W
S1 4
RED
S41
S51
RED
ORG
YLW
PNK
BLU
WHT
ORG
BRN
BLU
S32
S21
HA
M1S
M
M
FG
F1U
H2P~H4P
M1F
M1S, M2S, M3S
PCB1, PCB2, PCB3
R1T, R2T
S1~S51
S1W
S2W
X1M
M
M3S
indoor
M1F
outdoor
E1
E2
M2S
: Frame ground
: Fuse
: Pilot lamp
: Fan motor
: Swing motor
: Printed circuit board
: Thermistor
: Connector
: Operation switch
: Panel limit switch
: Terminal strip
: Protective earth
: Earth terminal (Schield plate)
: Earth terminal (Heat. plate)
3D050493
2.1.2 Duct Connected Type
FDK(X)S25/35CAVMB, FDK(X)S50/60CVMB, FDK(X)S25/35EAVMB
X1M
PCB1
PCB2
H1
F1U
3.15A
V1TR
LED LED LED S1
1
H1P H2P H3P
S26
1
H3
6
S21
S1W
Signal
receiver
10
2 RTH11
3
1
Transmission
GND
circuit
S1
RED
S7
10
1
2 S32 1
GRY
BLK
YLW
3
C1
WHT
t°
R1T
BRN BRN
t°
PPL
BLU
R2T
Infrared
remote
control
M
1~
indoor
:
C1 :
F1U :
Protective earth
Running capacitor
Fuse
M1F
Q1M
130°C
1
WHT
2
RED
3
1
2
3
outdoor
Z1C
H2
(Terminal for
centralized control)
BLK
H1P ~ H3P
M1F
PCB1 ~ PCB2
Q1M
R1T ~ R2T
S1 ~ S32, RTH1
S1W
V1TR
X1M
Z1C
N=2
GRN / YLW
GRN / YLW
FIELD WIRING.
CAUTION
Note that operation will
restart automatically if
the main power supply is
turned off and then back on
again.
Pilot lamp
Fan motor
Printed circuit board
Thermal protector (M1F embedded)
Thermistor
Connector
Operation switch
Phase control circuit
Terminal block
Noise filter (ferrite core)
3D045012K
304
Appendix
SiEBE12-625
Wiring Diagrams
2.1.3 Floor / Ceiling Suspended Dual Type
FLK(X)S25/35/50/60BAVMB
PCB3
S25
PCB1
S24
S37
PCB2
S36
H1
LED LED LED
Fu
3.15A
H1P H2P H3P
BLK
WHT
RED
GRN/
YLW
H2
PCB4
C70
S1W
Transmission H3
circuit
X1M
1
2
3
S27
S26
S31
S7
S21
S32
t°
t°
R1T
R2T
H4
H5
outdoor
CAUTION
Note that operation will
restart automatically if
the main power supply is
turned off and then back
on again.
H6
indoor
S6
?
FIELD WIRING.
HA
Signal
receiver
1
2
3
X11A
X21A
: Protective earth
C70
: Running capacitor
FU
: Fuse
H1P~H3P : Pilot lamp
M1F
: Fan motor
M1S
: Swing motor
M
M
Infrared
remote
control
1~
t°
M1S
M1F
100°C
PCB1~PCB4
R1T~R2T
S6~S37, X11A, X21A
S1W
X1M
: Printed circuit board
: Thermistor
: Connector
: Operation switch (SW7)
: Therminal strip
3D033909E
2.1.4 Floor Standing Type
FVK(X)S25/35/50BAVMB
PCB3
S26
S2W(4)
S4W
Transmission
circuit
PCB2
Infrared
remote
control
3.15A
H1
FU
H2
S25
BLK
WHT
RED
GRN/
YLW
H3
S8
S201
S202
S203
S204
S301
S43
PCB1
FG
S23
H1P H2P H3P
S1W
Signal
receiver
S6
M1S
S21
HA
M
S41
M2S
M
L1S
indoor
S302
S31
S32
outdoor
FIELD WIRING.
S7
PCB4
S24
1
2?
3
X1M
1
2
3
M
M1F
(UPPER FAN MOTOR)
M
M2F
(LOWER FAN MOTOR)
S44
: Protective earth
FU
: Fuse
H1P, H2P, H3P : Pilot lamp
L1S
: Limit switch
M1F, M2F
: Fan motor
M1S
: Swing motor
M2S
: Lower air outlet motor
PCB1~PCB4 : Printed circuit board
R1T, R2T
: Thermistor
S6~S302
: Connector
S1W
: Operation switch
S2W(4)
: Upward air flow limit switch
S4W
: Air outlet selection switch
X1M
: Terminal strip
S42
R1T
R2T
3D034713C
Appendix
305
Wiring Diagrams
2.2
SiEBE12-625
Outdoor Units
2.2.1 Cooling only
1
1
2
3
Z1C~Z3C
X1M~X5M
Y1E~Y4E
V2~V5
FU1, FU2, FU201
HE, HL, HN
E, AC1, AC2
H1, H2, L1
L2,
MRM10, MRM20
MRB, MRD
MRC/W
R1T~R12T
S2~S102
H1P~H5P
MID1~MID2
S52
H5P H4P H3P H2P H1P
FERRITE CORE
TERMINAL STRIPS
ELECTRONIC EXPANSION VALVE COIL
VARISTOR
FUSE
: CONNECTOR
:
:
:
:
:
MAGNETIC RELAY
THERMISTOR
CONNECTOR
PILOT LAMP
MOLDED INTERCONNECT DEVICE
M
M
M
M
Y1E
S4W
t°
t°
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
LIVE
NEUTRAL
FORCED OPERATION ON/OFF SW (SW1)
SELECT SW (SW2)DIODE BRIDGE
WIRING ERROR CHECK SW (SW3)
PRIORITY ROOM SETTING SW (SW4)
NIGHT QUIET MODE SETTING SW (SW5)
SURGE ARRESTER
PRINTED CIRCUIT BOARD
DIODE BRIDGE
COMPRESSOR MOTOR
FAN MOTOR
REACTOR
OVERLOAD PROTECTOR
SYSTEM POWER MODULE
CURRENT TRANSFORMER
t°
8
t°
t° t°
BLK
BLK
GRY
BLU
RED
S92
1
R3T R2T R1T
Y3E
Y2E
1 S90 6
10 1
4
S40
S33
8
S93
1
t°
9
BLU
S71
1
S6
t° t°
t°
t°
R8T R9T R10T R11T R4T R5T R6T R7T
Y4E (OUTDOOR) (DISCHARGE) (ROOM-A) (ROOM-C)
(ROOM-A) (ROOM-C)
(ROOM-B) (ROOM-D)
(ROOM-B) (ROOM-D)
(CONDENSER)
L
N
S1W
S2W
S3W
S4W
S5W
SA1
PCB
DB1
M1C
M1F
L1R
Q1L
SPM
CT1
YLW
8 1
BRN
1
Q1L
10
YLW
C
A
B
D
1 S20 6 1 S21 6 1 S22 6 1 S23 6
9
S34
8 1
M1C
U
RED
V
YLW M N
3
BLU
W
BRN
GRY
S80
X11A
S31
PCB
12 1 S102 5
S2
S2W S5W S1W S3W
:
:
:
:
:
9
BLU
YLW
RED
BRN
BLK
X5M
1
2
3
1
1
W
V
U
N
RED
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
1
2
3
12 1 S101 5
S51
S32
WHT
YLW
ORG
BLU
BRN
RED
7
1
5
WHT
YLW
ORG
BLU
BRN
RED
WHT
1
WHT
YLW
ORG
BLU
BRN
RED
7
3
1
S72
1
10
WHT
YLW
ORG
BLU
BRN
RED
WHT
X4M
1
2
3
ROOM D
MRB
ROOM C
S91
WHT
CN14
1
BLK
1
2
3
S10
1
RED
BLK
WHT
GRN
1
2
3
S11
1
WHT
BLK
BLK
BLK
BLK
BLK
X3M
5
t°
BLK
5
ROOM B
R12T
FU2
3.15A
V5
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
S15
1
MID1
1
2
3
WHT
BRN
CN11
1
MRD
MRC W
1
2
3
-
BLK
X2M
RED
BLU
SPM
1
GRY
BLK
V2
ROOM A
~-
N1
P2
TB6
TB5
TB4
BLK
CT1H2
AC2
+
RED
GRY
30A SA1
V3 HN
N
YLW
P1
N1
P2
W
V
U
L1
DB1
+
~
Z2C
H1
MRM10
RED
BLU
TO INDOOR UNIT
AC1
HL
FU1
L
WHT
ORG
BRN
BLU
4MKS75E2(3)V1B, 4MKS90DAVMB
(GAS PIPE)
(LIQUID PIPE)
ASSIGNMENTS OF
TERMINALS OF THE COMP.
U
V
N
W
3D034315J
2.2.2 Heat Pump
4MXS68E2(3)V1B, 4MXS80DAVMB
306
:
:
:
:
:
MAGNETIC RELAY
THERMISTOR
CONNECTOR
PILOT LAMP
H5P H4P H3P H2P H1P
S2W S5W S1W
L
N
S1W
S2W
S3W
S4W
S5W
SA1
Y1R
Y1S
PCB
DB1
M1C
M1F
L1R
Q1L
CT1
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
S3W
S4W
M
M
Y3E
t°
t°
t°
BLK
BLK
BLU
GRY
YLW
S33
10
1 S40 4
8
S92
1
8
t°
t°
t°
t°
S93
1
9
BLU
M
Q1L
10
YLW
WHT
YLW
ORG
BLU
BRN
RED
M
1 S90 6
RED
8 1
S71
1
BRN
1
U
RED
V
N
YLW M
3
BLU
W
BRN
S34
8 1
S6
B
C
D
A
1 S20 6 1 S21 6 1 S22 6 1 S23 6
Y2E
S72
M1C
X11A
BLU
YLW
RED
BRN
BLK
S31
PCB
Y1E
1
GRY
9
1
+
RED
S32
WHT
YLW
ORG
BLU
BRN
RED
9
Y1S Y1R
5
1
+
W
V
U
N
1
10
WHT
YLW
ORG
BLU
BRN
RED
12 1 S102 5
S2
3
CN14
+
N1
P2
TB6
TB5
TB4
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
BLK
S52
1
1
P1
P1
N1
P2
W
V
U
WHT
YLW
ORG
BLU
BRN
RED
1
5
S80
BLU
BLK
12 1 S101 5 1
S51
BLK
1
FERRITE CORE
TERMINAL STRIP
ELECTRONIC EXPANSION VALVE COIL
VARISTOR
FUSE
: CONNECTOR
:
:
:
:
7
WHT
MRD
MRC W
7
1
2
3
Z1C~Z3C
X1M~X5M
Y1E~Y4E
V2~V5
FU1, FU2, FU201
HE, HL, HN
E, AC1, AC2
H1, H2, L1
L2,
MRM10, MRM20
MRB, MRD
MRC/W
R1T~R12T
S2S~102
H1P~H5P
S91
WHT
X5M
1
2
3
S10
1
WHT
1
2
3
SPM
-
BLK
t°
MRB
X4M
1
2
3
1S11 WHT
RED
BLK
WHT
1
2
3
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
BLU
X3M
1
2
3
ROOM D
-
R12T
FU2
3.15A
V5
5
ROOM C
BLU
~
+
RED
BLK
BLK
BLK
BLK
BLK
S15
1
MID1
L2
CN11
1
BLU
1
2
3
ROOM B
~
X2M
1
2
3
ORG
L1
M1F
1M
BLU
BRN
ORG
WHT
BRN
V2
+
YLW
CT1 H2
AC2
ORG
DB1
RED
RED
BLK
ROOM A
Z2C
H1
MRM10
BLK
30A SA1
V3 HN
MRM20
E
AC1
HL
RED
S70
GRY
FU1
7
3.15A
WHT
ORG
BRN
BLU
N
HE
BLK
TO INDOOR UNIT
FU201
MID2
L1R
Z1C
BLU
X1M
L
GRN
YLW
GRN
FIELD WIRING
Z3C
YLW
GRY
GRN
t°
t°
t°
t°
R3T R2T R1T
R8T R9T R10T R11T
R4T R5T R6T R7T
Y4E (OUTDOOR) (DISCHARGE) (ROOM-A) (ROOM-C)
(ROOM-A) (ROOM-C)
(CONDENSER)
(ROOM-B) (ROOM-D) (ROOM-B) (ROOM-D)
(GAS PIPE)
(LIQUID PIPE)
MID1~MID2 : MOLDED INTER CONNECT DEVICE
LIVE
SPM
: SYSTEM POWER MODULE
NEUTRAL
FORCED OPERATION ON/OFF SW(SW1)
(
)
FORCED OPERATION MODE SELECT SW SW2
WIRING ERROR CHECK SW(SW3)
PRIORITY ROOM SETTING SW(SW4)
NIGHT QUIET MODE SETTING SW(SW5)
ASSIGNMENTS OF
SURGE ARRESTER
TERMINALS OF THE COMP.
REVERSING SOLENOID VALVE COIL
U
DEFROST SOLENOID VALVE COIL
PRINTED CIRCUIT BOARD
V
N
DIODE BRIDGE
COMPRESSOR MOTOR
W
FAN MOTOR
REACTOR
OVERLOAD PROTECTOR
CURRENT TRANSFORMER
3D034312J
Appendix
SiEBE12-625
Index
Numerics
3 minutes stand-by..................................................81
A
A1..........................................................................201
A5..................................................................202, 212
A6..................................................................204, 205
AC1 .........................................................................52
AC2 .........................................................................52
address setting jumper........36, 38, 41, 43, 45, 47, 49
adjusting the air flow direction...............................131
air purifying filter......................................................72
air purifying filter with photocatalytic deodorizing
function ............................................................72
anti-icing function in other rooms ..........................238
ARC433A ..............................................................195
AUTO • DRY • COOL • HEAT • FAN operation.....129
automatic air flow control ........................................61
automatic operation.................................................63
auto-restart........................................................36, 43
auto-restart function ................................................72
auto-swing...............................................................58
B
buzzer PCB .............................................................42
C
C4..........................................................................207
C7..................................................................208, 209
C9..........................................................................207
capacitor voltage check.........................................246
care and cleaning..................................................160
centralized control ...............36, 38, 41, 43, 45, 47, 49
check No.01 ..........................................................239
check No.02 ..........................................................239
check No.03 ..........................................................239
check No.04 ..........................................................240
check No.05 ..........................................................241
check No.06 ..........................................................242
check No.07 ..........................................................243
check No.08 ..........................................................244
check No.09 ..........................................................244
check No.10 ..........................................................245
check No.11 ..........................................................245
check No.12 ..........................................................246
check No.13 ..........................................................246
check No.14 ..........................................................247
check No.15 ..........................................................247
check No.16 ..........................................................248
CN11 .......................................................................53
CN14 .......................................................................53
compressor ...................................................272, 288
compressor lock ....................................................215
compressor overload.............................................214
compressor protection function ...............................81
Index
connection pipe condensation preventing function
........................................................................ 94
connectors.................... 36, 38, 41, 43, 45, 47, 49, 52
control PCB ........................................ 45, 47, 51, 280
control PCB (indoor unit) ...................... 37, 40, 42, 44
control PCB (outdoor unit)...................................... 53
cooling / heating mode lock.................................... 95
CT or related abnormality..................................... 225
D
DC fan lock........................................................... 216
defrost control ........................................................ 85
diagnosis mode .................................................... 196
discharge pipe ........................................................ 89
discharge pipe control ............................................ 82
discharge pipe temperature control...................... 221
discharge pipe thermistor ................... 74, 76, 89, 285
discharge pressure check .................................... 244
display PCB.................................... 37, 42, 46, 48, 51
E
E ............................................................................. 52
E5 ......................................................................... 214
E6 ......................................................................... 215
E7 ......................................................................... 216
E8 ......................................................................... 217
EA ........................................................................ 219
econo mode ........................................................... 66
econo operation ................................................... 145
electrical box ................................................ 254, 275
electrical box temperature rise ............................. 229
electronic expansion valve ................................... 266
electronic expansion valve check......................... 240
electronic expansion valve coil............................. 284
electronic expansion valve control ......................... 86
error codes
A1 .................................................................. 201
A5 .......................................................... 202, 212
A6 .......................................................... 204, 205
C4 .................................................................. 207
C7 .......................................................... 208, 209
C9 .................................................................. 207
E5 .................................................................. 214
E6 .................................................................. 215
E7 .................................................................. 216
E8 .................................................................. 217
EA .................................................................. 219
F3................................................................... 221
F6................................................................... 222
H6 .................................................................. 224
H8 .................................................................. 225
H9 .................................................................. 227
J3 ................................................................... 227
J6 ................................................................... 227
J8 ................................................................... 227
i
SiEBE12-625
J9 ....................................................................227
L3....................................................................229
L4....................................................................231
L5....................................................................233
P4 ...................................................................227
U0 ...................................................................235
U2 ...................................................................237
U4 ...................................................................210
UA...........................................................211, 238
UH ..................................................................238
error codes and description of fault.......................198
F
F3 ..........................................................................221
F6 ..........................................................................222
fan control ...............................................................84
fan motor .......................................................264, 282
fan motor connector output check.........................239
fan motor or related abnormality
AC motor ........................................................204
DC motor ........................................................205
fan speed control.....................................................61
fan speed setting.................36, 38, 41, 43, 45, 47, 49
forced operation mode ............................................91
forced operation ON/OFF switch
.....................................36, 38, 41, 43, 45, 47, 49
four way valve ...............................................270, 286
four way valve abnormality....................................219
four way valve coil.................................................284
four way valve operation compensation..................81
four way valve performance check........................241
four way valve switching .........................................81
freeze-up protection control ............................83, 212
freeze-up protection control or
high pressure control .....................................202
frequency control.....................................................79
frequency principle ..................................................56
front panel control ...................................................60
front panel mechanism....................................43, 209
front panel open/close fault ...................................209
FU ...........................................................................49
FU1 .....................................36, 38, 41, 43, 45, 47, 52
FU2 .........................................................................52
FU201 .....................................................................52
functions....................................................................2
fuse ...............................36, 38, 41, 43, 45, 47, 49, 52
G
gas pipe isothermal control during cooling..............88
gas pipe thermistor....................74, 76, 263, 276, 285
H
H1............................................................................52
H2............................................................................52
H6..........................................................................224
H8..........................................................................225
H9..........................................................................227
HA ...............................................................36, 41, 43
Hall IC .....................................................61, 204, 205
Hall IC check .........................................................248
HE ...........................................................................52
ii
heat exchanger thermistor ................................... 285
heating peak-cut control ......................................... 83
high pressure control in cooling ........................... 222
HL........................................................................... 52
HN .......................................................................... 52
HOME LEAVE operation ................................ 69, 146
hot start function..................................................... 71
I
indoor heat exchanger thermistor .................... 75, 77
indoor unit PCB abnormality ................................ 201
input current control ............................................... 82
input over current detection.................................. 217
installation condition check .................................. 243
instruction ............................................................... 99
insufficient gas ..................................................... 235
insufficient gas control............................................ 90
INTELLIGENT EYE ................................................ 67
INTELLIGENT EYE operation .............................. 148
INTELLIGENT EYE sensor .................................. 292
INTELLIGENT EYE sensor PCB.......... 37, 40, 42, 44
inverter PCB ................................................. 263, 281
inverter PCB (MID2) ............................................... 54
inverter POWERFUL operation .............................. 70
inverter units refrigerant system check................. 245
J
J3 ......................................................................... 227
J4 ......................................................................... 291
J6 ......................................................................... 227
J8 ......................................................................... 227
J9 ......................................................................... 227
JA ............................... 36, 38, 41, 43, 45, 47, 49, 291
JB ............................... 36, 38, 41, 43, 45, 47, 49, 291
JC ............................... 36, 38, 41, 43, 45, 47, 49, 291
jumper setting....................................................... 291
L
L1 ........................................................................... 53
L2 ........................................................................... 53
L3 ......................................................................... 229
L4 ......................................................................... 231
L5 ......................................................................... 233
LED A ........................... 36, 38, 41, 43, 45, 47, 49, 52
LED1 ........................................ 36, 38, 41, 45, 47, 52
LED11 .................................................................... 49
LED12 .................................................................... 49
LED14 .................................................................... 49
LED2 .................................. 36, 38, 41, 43, 45, 47, 52
LED3 .................................. 36, 38, 41, 43, 45, 47, 52
LED4 ................................................................ 43, 52
limit switch ...................................................... 43, 209
limit switch continuity check ................................. 239
liquid compression protection function 2 ................ 84
liquid pipe thermistor ...................... 75, 263, 276, 285
low Hz high pressure limit ...................................... 86
low-voltage detection ........................................... 237
M
main circuit electrolytic capacitor check ............... 247
main structural parts............................................... 73
Index
SiEBE12-625
MID1........................................................................53
MID2........................................................................54
mode hierarchy .......................................................78
mold proof air filter ..................................................72
motor
reduction motor.................................................43
multi system ..........................................................158
signal receiver PCB ........... 37, 40, 42, 44, 48, 51
SPM ................................................................. 54
printed circuit board connector wiring diagram....... 36
priority room setting................................................ 94
problem symptoms and measures ....................... 194
programme dry function ......................................... 62
propeller fans ....................................................... 253
N
R
N..............................................................................52
names of parts ......................................................102
night set mode.........................................................65
radiation fin temperature rise ............................... 231
reactor .................................................................. 267
reduction motor .............................................. 43, 209
remote controller .................................................. 195
RTH1 .............................................. 36, 38, 41, 43, 45
O
oil recovery function ................................................89
OL activation .........................................................214
ON/OFF button on indoor unit.................................71
opening limit ............................................................88
operation lamp ......................................................192
outdoor air thermistor ............................................285
outdoor heat exchanger thermistor ...................74, 76
outdoor unit fan system check (with DC motor) ....244
OUTDOOR UNIT SILENT operation.....................144
outer panels ..................................................250, 274
output over current detection ................................233
over current .............................................................90
overload ..................................................................90
overload protector ...................................................52
overload relay........................................................276
P
P4..........................................................................227
PCB...............................................................261, 279
photocatalytic deodorizing filter...............................72
PI control .................................................................80
piping diagrams.....................................................294
position sensor abnormality ..................................224
power failure recovery function
.....................................36, 38, 41, 43, 45, 47, 49
power supply PCB.............................................48, 50
power supply waveforms check ............................245
power transistor check ..........................................246
power-airflow dual flaps ..........................................58
POWERFUL operation..........................................143
POWERFUL operation mode..................................94
preheating operation ...............................................81
preparation before operation.................................126
pressure equalization control ..................................88
preventing indoor freezing.......................................91
printed circuit board (PCB)
buzzer PCB ......................................................42
control PCB ..................................45, 47, 51, 280
control PCB (indoor unit) ................37, 40, 42, 44
control PCB (outdoor unit) ................................53
display PCB ..............................37, 42, 46, 48, 51
INTELLIGENT EYE sensor PCB ....37, 40, 42, 44
inverter PCB ...........................................263, 281
inverter PCB (MID2) .........................................54
MID1 .................................................................53
power supply PCB ......................................48, 50
service monitor PCB .......................263, 279, 281
Index
S
S1 ................................................... 36, 38, 41, 43, 45
S10 ......................................................................... 52
S101 ....................................................................... 52
S102 ....................................................................... 52
S11 ......................................................................... 52
S20 ................................................. 52, 256, 263, 276
S201 ....................................................................... 49
S202 ....................................................................... 49
S203 ....................................................................... 49
S204 ....................................................................... 49
S21 ....... 36, 38, 41, 43, 45, 47, 49, 52, 256, 263, 276
S22 ................................................. 52, 256, 263, 276
S23 ........................................... 49, 52, 256, 263, 276
S24 ................................................................... 47, 49
S25 ................................................................... 47, 49
S26 ........................................... 36, 38, 41, 45, 47, 49
S27 ....................................................... 36, 38, 41, 47
S28 ................................................................... 36, 41
S29 ................................................................... 36, 41
S301 ....................................................................... 49
S302 ....................................................................... 49
S31 ............................................. 47, 49, 52, 263, 280
S32 ............... 36, 38, 41, 43, 45, 47, 49, 52, 263, 280
S33 ......................................................... 52, 263, 280
S34 ......................................................................... 52
S35 ............................................................. 36, 38, 41
S36 ................................................. 36, 38, 41, 43, 47
S37 ................................................................... 41, 47
S38 ......................................................................... 41
S40 ................................................. 52, 257, 263, 276
S41 ......................................................................... 43
S46 ......................................................................... 43
S47 ......................................................................... 43
S49 ......................................................................... 43
S51 ................................................................... 43, 52
S52 ......................................................................... 52
S6 ................................................... 36, 38, 41, 47, 49
S7 ......................................................... 38, 45, 47, 49
S70 ................................................................. 52, 264
S71 ......................................................... 52, 263, 280
S72 ......................................................................... 52
S8 ..................................................................... 41, 49
S80 ................................................. 52, 256, 263, 276
S90 ......................................... 52, 257, 263, 276, 285
S91 ......................................................................... 52
iii
SiEBE12-625
S92..........................................52, 257, 263, 276, 285
S93..........................................52, 256, 263, 276, 285
safety precautions .................................................100
SC control ...............................................................88
self-diagnosis digital display....................................72
sensor malfunction detection ..................................90
service check function...........................................195
service monitor PCB .............................263, 279, 281
shunt .....................................................269, 286, 287
shutter drive motor /
shutter limit switch abnormality ......................208
signal receiver PCB...................37, 40, 42, 44, 48, 51
signal receiving sign................................................71
signal transmission error
(between indoor and outdoor units) ...............210
solenoid valve .......................................270, 286, 287
solenoid valve coil .................................................284
sound blanket................................................267, 283
specifications...........................................................14
SPM ........................................................................54
starting control
indoor unit .........................................................60
SW1 ..........................................36, 41, 43, 45, 47, 49
SW2 ..................................................................47, 49
SW4 ........................................................................49
SW7 ........................................................................38
V
V ............................................................................. 52
V1 ....................................... 36, 38, 41, 43, 45, 47, 49
V2 ........................................................................... 52
V3 ........................................................................... 52
V5 ........................................................................... 52
varistor ......................... 36, 38, 41, 43, 45, 47, 49, 52
voltage detection function ...................................... 94
W
W ............................................................................ 52
wide-angle louvers ................................................. 58
wiring diagrams .................................................... 302
wiring-error check................................................... 92
T
target discharge pipe temperature control ..............89
test run from the remote controller ........................290
thermistor ......................................263, 266, 276, 284
discharge pipe thermistor .............74, 76, 89, 285
gas pipe thermistor .............74, 76, 263, 276, 285
heat exchanger thermistor ..............................285
indoor heat exchanger thermistor ...............75, 77
liquid pipe thermistor ................75, 263, 276, 285
outdoor air thermistor .....................................285
outdoor heat exchanger thermistor.............74, 76
thermistor or related abnormality (indoor unit) ......207
thermistor or related abnormality (outdoor unit) ....227
thermistor resistance check ..................................242
thermostat control ...................................................64
TIMER operation ...................................................156
titanium apatite photocatalytic air-purifying filter .....71
troubleshooting......................................................185
indoor units .....................................................199
outdoor units ...................................................200
troubleshooting with the LED indication ................193
troubleshooting with the operation lamp ...............192
turning speed pulse input on the outdoor unit PCB
check..............................................................247
U
U..............................................................................52
U0..........................................................................235
U2..........................................................................237
U4..........................................................................210
UA .................................................................211, 238
UH .........................................................................238
unspecified voltage
(between indoor and outdoor units) .......211, 238
iv
Index
SiEBE12-625
Drawings & Flow Charts
A
anti-icing function in other rooms ..........................238
ARC433A ..............................................................195
automatic air flow control ........................................61
automatic operation.................................................63
auto-swing...............................................................58
B
buzzer PCB .............................................................42
C
capacitor voltage check.........................................246
compressor lock ....................................................215
compressor overload.............................................214
compressor protection function ...............................81
control PCB .......................................... 45, 47, 51, 53
control PCB (indoor unit)...................... 37, 40, 42, 44
cooling / heating mode lock.....................................95
CT or related abnormality......................................225
high pressure control in cooling ........................... 222
HOME LEAVE operation ........................................ 69
I
indoor unit PCB abnormality ................................ 201
input current control ............................................... 82
input over current detection.................................. 217
installation condition check .................................. 243
insufficient gas ..................................................... 235
insufficient gas control............................................ 90
INTELLIGENT EYE ................................................ 67
INTELLIGENT EYE sensor .................................. 292
INTELLIGENT EYE sensor PCB.......... 37, 40, 42, 44
inverter features ..................................................... 57
inverter PCB (MID2) ............................................... 54
inverter POWERFUL operation .............................. 70
inverter units refrigerant system check................. 245
J
jumper settings ..................................................... 291
D
DC fan lock............................................................216
defrost control .........................................................85
diagnosis mode .....................................................196
discharge pipe control .............................................82
discharge pipe temperature control.......................221
discharge pressure check .....................................244
display PCB.................................... 37, 42, 46, 48, 51
E
econo mode ............................................................66
electrical box temperature rise ..............................229
electronic expansion valve check..........................240
electronic expansion valve control ..........................86
F
fan motor connector output check.........................239
fan motor or related abnormality
AC motor ........................................................204
DC motor ........................................................205
four way valve abnormality....................................219
four way valve performance check........................241
freeze-up protection control ........................... 83, 212
freeze-up protection control or high pressure control
.......................................................................202
frequency control.....................................................79
frequency principle ..................................................56
front panel open/close fault ...................................209
function of thermistor...............................................74
cooling only model ............................................76
heat pump model ..............................................74
H
Hall IC check .........................................................248
heating peak-cut control..........................................83
Drawings & Flow Charts
L
limit switch continuity check ................................. 239
location of operation lamp .................................... 192
low Hz high pressure limit ...................................... 86
low-voltage detection ........................................... 237
M
main circuit electrolytic capacitor check ............... 247
main structural parts............................................... 73
MID1....................................................................... 53
MID2....................................................................... 54
mode hierarchy ...................................................... 78
N
night set mode........................................................ 65
O
OL activation ........................................................ 214
ON/OFF button on indoor unit ................................ 71
outdoor unit fan system check (with DC motor) ... 244
output over current detection ............................... 233
P
PCB ........................................................................ 39
piping diagrams
4MKS75E2(3)V1B ......................................... 300
4MKS90DAVMB ............................................ 300
4MXS68E2(3)V1B ......................................... 301
4MXS80DAVMB ............................................ 301
CTXG50EV1BW(S) ....................................... 296
FDK(X)S25/35CAVMB................................... 297
FDK(X)S25/35EAVMB................................... 297
FDK(X)S50/60CVMB ..................................... 297
FLKS25/35BAVMB ........................................ 297
v
SiEBE12-625
FLKS50/60BAVMB .........................................297
FLXS25/35BAVMB .........................................298
FLXS50/60BAVMB .........................................298
FTK(X)S50/60EV1B .......................................295
FTKS20/25/35CAVMB....................................294
FTKS20/25/35D3VMW(L)...............................294
FTKS50D2V1W(L)..........................................295
FTKS71BAV1B ...............................................295
FTKS71EV1B .................................................295
FTXG25/35EV1BW(S)....................................296
FTXS20/25/35CAVMB....................................294
FTXS20/25/35D3VMW(L)...............................294
FTXS50D2V1W(L)..........................................295
FTXS71BAVMB ..............................................296
FTXS71EV1B .................................................296
FVKS25/35BAVMB.........................................298
FVKS50BAVMB..............................................299
FVXS25/35BAVMB.........................................298
FVXS50BAVMB..............................................299
position sensor abnormality ..................................224
power supply PCB...................................................48
power supply PCB (25, 35 class) ............................50
power supply PCB (50 class) ..................................50
power supply waveforms check ............................245
power transistor check ..........................................246
priority room setting.................................................94
programme dry function ..........................................62
4MXS68E2(3)V1B ......................................... 306
4MXS80DAVMB ............................................ 306
CTXG50EV1BW(S) ....................................... 304
FDK(X)S25/35CAVMB................................... 304
FDK(X)S25/35EAVMB................................... 304
FDK(X)S50/60CVMB ..................................... 304
FLK(X)S25/35/50/60BAVMB ......................... 305
FTK(X)S20/25/35CAVMB .............................. 302
FTK(X)S20/25/35D3VMW(L) ......................... 302
FTK(X)S50/60/71EV1B.................................. 303
FTK(X)S50D2V1W(L) .................................... 303
FTK(X)S71BAVMB ........................................ 303
FTKG25/35EV1BW(S)................................... 304
FVK(X)S25/35/50BAVMB .............................. 305
wiring-error check................................................... 92
R
radiation fin temperature rise ................................231
remote controller ...................................................195
S
shutter drive motor / shutter limit switch abnormality
.......................................................................208
signal receiver PCB..................37, 40, 42, 44, 48, 51
signal transmission error
(between indoor and outdoor units) ...............210
SPM ........................................................................54
starting control flow .................................................60
starting timing chart.................................................60
T
target discharge pipe temperature control ..............89
thermistor or related abnormality (indoor unit) ......207
thermistor or related abnormality (outdoor unit) ....227
thermistor resistance check ..................................242
thermostat control ...................................................64
trial operation from remote controller ....................290
troubleshooting with the LED indication ................193
turning speed pulse input on the outdoor unit PCB
check..............................................................247
U
unspecified voltage
(between indoor and outdoor units) ...... 211, 238
W
wiring diagrams
4MKS75E2(3)V1B ..........................................306
4MKS90DAVMB .............................................306
vi
Drawings & Flow Charts
Daikin Europe N.V. is approved by LRQA for its Quality
Management System in accordance with the ISO9001
standard. ISO9001 pertains to quality assurance
regarding design, development, manufacturing as well
as to services related to the product.
Daikin units comply with the European regulations that
guarantee the safety of the product.
ISO14001 assures an effective environmental
management system in order to help protect human
health and the environment from the potential impact
of our activities, products and services and to assist in
maintaining and improving the quality of the
environment.
Daikin Europe N.V. participates in the Eurovent
Certification Programme for Air Conditioners (AC),
Liquid Chilling Packages (LCP) and Fan Coil Units (FC);
the certified data of certified models are listed in the
Eurovent Directory.
SiEBE12-625 • 01/2007
Prepared in Belgium by Lannoo
"The present publication is drawn up by way of
information only and does not constitute an offer
binding upon Daikin Europe N.V.. Daikin Europe N.V.
has compiled the content of this publication to the
best of its knowledge. No express or implied
warranty is given for the completeness, accuracy,
reliability or fitness for particular purpose of its
content and the products and services presented
therein. Specifications are subject to change without
prior notice. Daikin Europe N.V. explicitly rejects any
liability for any direct or indirect damage, In the
broadest sense, arising from or related to the use
and/or interpretation of this publication. All content is
copyrighted by Daikin Europe N.V.."
Zandvoordestraat 300
B-8400 Ostend - Belgium
www.daikineurope.com
q<R.+.#st