Location:
Duro
™
Shower Valve System
3600
Specification Submittal
Feature Highlights
■ Symmons Shower Valve System with Symmons Temptrol to limit handle turn
® pressure-balancing mixing valve with adjustable stop screw
■ Screwless escutcheon
■ Lever style handle
■ Polished chrome finish (standard)
Model Numbers
3600
Shower Valve System with Symmons Temptrol mixing valve p/n 4000-BODY
®
3600-TRM
Trim only, mixing valve ordered separately
3600-REB-TRM
Rebuild kit, Trim only, includes TA-10 flow control spindle and TA-4 hot/cold seat
4000-BODY
Symmons Temptrol ® mixing valve without trim
4000-X-BODY
Symmons Temptrol shut-off for service
® mixing valve without trim.
Valve includes integral service stops to allow water
Options / Modifications
Append appropriate -suffix to model number
-IPS 1/2 inch female IPS connections on
Symmons Temptrol
®
mixing valve
-X Integral service stops included with Temptrol mixing valve to allow water shut-off for service, p/n 4000-X-BODY (option only
applies when ordering model 3600)
-CHKS Check Stops: Temptrol ® mixing valve includes integral check stops
(Requires integral service stops, suffix -X .
Used in installations where a positive shut-off device is used downstream of mixing valve.)
-REV Reverse core: Temptrol® mixing valve with reverse core. (Requires integral service stops, suffix -X . Used in back-to-back system installations. HOT on the right, COLD on the left)
-LW Wide lever handle (chrome finish only)
Standards / Certifications
ASME A112.18.1-2005 / CSA B125.1-05
Americans with Disabilities Act (ADA) compliant
Finish Options / Modifications
Append appropriate -suffix to model number
-STN Satin nickel
Polished chrome (standard finish)
Warranty
■ Limited Lifetime - to the original end purchaser in consumer installations
■ 5 years - for commercial installations
Print
Email Reset Form
Dimensions
Duro Shower Valve System, 3600
finished wall showerhead supply Finished wall to pipe centerline
2-3/8" ± 1/2" (60 mm ±13 mm)
*See note (2)
Finished wall to rear of valve
3-1/2" ± 1/2" (89 mm ±13 mm
Wall cutout hole size
3-1/2" (89 mm) min
4" (101 mm) min
7-1/2" sq
(191 mm)
3-1/8"
(80 mm)
HOT supply
COLD supply
32"
(813 mm) showerhead supply
valve mounting
plate,
* Notes (1)(2)
Temptrol control valve
3-3/8" ± ½"
(85 mm ±13 mm) hot / cold supply
Floor
* Notes:
(1) Walls for using T-177 mounting plate (MP)
■ Wall is 1/16" (2 mm) min • 1/2" (13 mm) max
■ Fiber or acrylic walls (MP required)
■ Plaster or other type walls 1/2" or less (MP optional)
■ Protective shield usage (optional)
(2) Dry wall, plaster or other type walls 1/2" or greater
■ Protective shield is required; snaps on end of valve spindle....
(3) Do not install positive shut-off devices or devices that do not
allow the valve to flow at least 1.5 gpm on control valve outlets.
(4) Dimensions subject to change without notice
Protective Shield p/n T-176
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800)796-6667 ■ Fax: (800)961-9621
©2014 Symmons Industries, Inc.
■
Printed in U.S.A.
■
www.symmons.com
■
[email protected]
■
092614