Mantis 811127 Operator`s manual

OPERATOR / PARTS MANUAL
8 Amp Electric Snow Shovel
811127
WARNING
CALIFORNIA Proposition 65 Warning
Battery post, terminals, wiring insulation, and
related accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer, birth defects and other
reproductive harm.
WASH HANDS AFTER HANDLING.
IMPORTANT MESSAGE
Thank you for purchasing this Mantis product. You have purchased a world class product, one of the best designed and built anywhere.
This machine comes with an Operator / Parts Manual. The useful life and good service you receive from this machine depends to a
large extent on how well you read and understand this manual. Treat your machine properly, lubricate and adjust it as instructed, and
it will give you many years of reliable service.
Your safe use of this Mantis product is one of our prime design objectives. Many safety features are built in, but we also rely on your
good sense and care to achieve accident-free operation. For best protection, study the manuals thoroughly. Learn the proper operation
of all controls. Observe all safety precautions. Follow all instructions and warnings completely. Do not remove or defeat any safety
features. Make sure those who operate this machine are as well informed and careful in its use as you are.
Mantis designs and builds its equipment to serve many years in a safe and productive manner. For longest life, use this machine only
as directed in the manuals, keep it in good repair and follow safety warnings and instructions. You’ll always be glad you did.
Schiller Grounds Care, Inc.
1028 Street Road
Southampton, PA 18966 U.S.A.
PHONE 215-357-5110 • FAX 215-357-8045
TABLE OF CONTENTS
PAGE
SAFETY RULES & WARNINGS ...................................................................................................................4-6
ASSEMBLY....................................................................................................................................................7-8
ELECTRICAL ................................................................................................................................................... 9
OPERATION ................................................................................................................................................... 10
STORAGE & TRANSPORTATION.................................................................................................................. 11
MAINTENANCE.........................................................................................................................................12-15
PARTS SECTION.......................................................................................................................................16-17
TROUBLESHOOTING.................................................................................................................................... 18
LIMITED WARRANTY..................................................................................................................................... 19
This Operator / Parts Manual is part of the machine. Suppliers of both new and
second-hand machines must make sure that this manual is provided with the
machine.
2
8 Amp Electric Snow Shovel Operator’s Manual
Contact us at www.mantis.com
3
Safety Rules & Warnings
Safety Rules & Warnings
You will notice throughout this Owners Manual Safety Rules and Important Notes. Make sure you understand and obey these
warnings for your own protection.
I. special safety information
WARNING
WARNING
Attention: This symbol points out our important
safety instructions. When you see this symbol ,
heed it’s warning !! Stay alert !!
To reduce the potential for accidents, comply with
the safety instructions in this manual. Failure to
comply may result in serious personal injury, and/
or equipment and property damage.
Ii. safety & warnings
WARNING
Improper use or care of this machine or failure
to wear proper protection can result in serious
injury. Read and understand the rules for safe operation and all instructions in this manual. Wear
hearing and eye protection.
III. Safety decal information
An important part of the safety system incorporated in this snow shovel are the warning and information decals found on
various parts of the snow shovel. These decals must be replaced in time due to abrasion, etc. It is your responsibility to
repalce these decals when they become hard to read.
Precautions that involve
your safety.
Wear ear protection
when operating this
machine.
4
Read Operator/Parts
Manua before using
snow shovel, or
performing any repair
or maintenance. Keep
owner’s manual in asafe
place.
Wear eye protection
when operating this
machine.
Keep all bystanders
(especially children and
pets) at least 50’ away
from the work area.
Waste electrical
products should not
be disposed of with
household waste.
Recycle where facilities
exist.
Pay attention that
bystanders are not
injured through foreign
objects thrown from the
snow shovel.
Keep hands away from
the collector/impeller.
Keep hands and feet
away from rotating
parts.
Danger - Keep feet
away from the collector/
impeller.
8 Amp Electric Snow Shovel Operator’s Manual
The power supply must
be disconnected before
carrying out cleaning
or maintenance.
Shut off the motor
before unclogging the
discharge shute.
iv. SAFETY rules
This appliance is NOT intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
TRAINING
1. Read the operating and service instruction manual
carefully. Be thoroughly familiar with the controls and the
proper use of the equipment. Know to stop the unit and
disengage the controls quickly.
2. Never allow children to operate the equipment. Never allow
adults to operate the equipment without proper instruction.
3. Keep the area of operation clear of all persons, particularly
small children, and pets.
4. Exercise caution to avoid slipping or falling, especially
during operation.
PREPARATION
1. Thoroughly inspect the area where the equipment is to
be used and remove all doormates, sleds, boards, wires,
and other foreign objects.
2. Do not operate the equipment without wearing adequate
winter garments. Wear footwear, which will improve footing
on slippery surfaces.
OPERATION
1. Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
2. Exercise extreme caution when operating on or crossing
gravel drives, walks, or roads. Stay alert for hidden
hazards or traffic.
3. After striking a foreign object, stop the motor, disconnect
the power supply, thoroughly inspect the snow thrower
for any damage, and repair the damage before restarting
and operating the snow thrower.
4. If the unit should start to vibrate abnormally, stop the motor,
disconnect the power supply and check immediately for
the cause. Vibration is generally a warning of trouble.
5. Stop the motor and disconnect the power supply, before
unclogging the collector/impeller housing or discharge
guide, and when making any repairs, adjustments, or
inspections.
6. When cleaning, repairing, or inspecting, make certain
the collector/impeller and all moving parts have stopped.
7. Do not clear snow across the face of slopes. Exercise
extreme caution when changing direction on slopes. Do
not attempt to clear steep slopes.
8. Never operate the snow thrower without proper guards,
plates or other safety protective devices in place.
9. Never operate the snow thrower near glass enclosures,
automobiles, window wells, etc. without proper adjustment
of the snow discharge angle. Keep children and pets away.
10. Do not overload the machine capacity by attempting to
clear snow at too fast a rate.
11. Never direct discharge at bystanders or allow anyone in
front of the unit.
12. Disconnect the power supply when the snow thrower is
transported or not in use.
13. Use only attachments and accessories approvedby the
manufacturer of the snow thrower.
14. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
MAINTENANCE AND STORAGE
1. Check the unit at frequent intervals to be sure the
equipment is in safe working condition.
2. Always refer to owner’s guide instructions for important
details if the snow thrower is to be stored for an extended
period.
3. Maintain or replace safety and instructions labels, as
necessary.
4. Run the machine a few minutes after throwing snow to
prevent freeze-up of the collector/impeller.
5. General maintenance written instructions shall be
provided with the equipment for maintenance operations
recommended by the manufacturer to maintain the
equipment in safe operating condition.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing,
use only identical replacement parts.
If the supply cord is damaged, it must replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
Contact us at www.mantis.com
5
Assembly
Safety Rules & Warnings
WARNING
To avoid serious personal injury, do not attempt
to use this product until you have read this
Owner’s Manual thoroughly and understand it
completely.
WARNING
The operation of any power tool can result
in foreign objects being thrown into your
eyes, which can result in severe eye damage. Before beginning power tool operation,
always wear safety goggles or safety glasses with
side shields and, when needed, a full face shield.
We recommend Wide Vision Safety Mask for use
over eyeglasses or standard safety glasses with
side shields. Always use eye protection which is
marked to comply with EN 166.
DESCRIPTION (Figure 1)
1. Trigger switch
2. Lock-out button
3. Auxiliary handle
4. Cord retainer
5. Belt drive cover
6. Impeller
7. Scraper
2
4
1
3
WARNING
Do not use this product if any parts on the packing list are already assembled to your product
when you unpack it. Parts on this list are not assembled to the product by the manufacturer and
require customer installation. Use of a product
that may have been improperly assembled could
result in serious personal injury.
This product requires assembly.
• Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list are
included.
• Inspect the product carefully to make sure no breakage or
damage occurred during shipping.
• Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
• If any parts are damaged or missing, please call your Mantis
tools service centre for assistance.
5
6
7
FIGURE 1
PACKING LIST
• Snow shovel
• Owner’s Manual
WARNING
If any parts are damaged or missing, do not operate this product until the parts are replaced. Failure to heed this warning could result in serious
personal injury.
WARNING
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse, and could result in a hazardous condition
leading to possible serious personal injury.
WARNING
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental starting and possible serious personal injury.
6
8 Amp Electric Snow Shovel Operator’s Manual
WARNING
Do not allow familiarity with this product to make
you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
Contact us at www.mantis.com
7
Electrical
Assembly
CONNECTING THE POLES (Figure 2)
DOUBLE INSULATION
1. Carefully remove the product and any accessories from
the box. Make sure that all items listed are included.
2. Remove packaging material from cord and discard
immediately.
3. Align the holes on the handle pole and the lower pole. Insert
the bolt and tighten them using the lock knob provided.
This snow shovel is “DOUBLE INSULATED”
WARNING
Make sure not to pinch the power cord ; Make certain all nuts and bolts are tightened securely.
•Inspect the extension cord and the power cord on a
regular basis. Look for deterioration, cuts, or cracks in the
insulation. Inspect the connections for damage. Repair
or replace the extension cord or the power cord if any
damage is found.
WARNING
Do not use this product if any parts on the packing list are already assembled to your product
when you unpack it. Parts on this list are not assembled to the product by the manufacturer and
require customer installation. Use of a product
that may have been improperly assembled could
result in serious personal injury.
Bolt
Holes
Lock knob
In order to reduce the risk of electric shock when
operating this Snow Shovel, use only a CSAlisted extension cord that is approved for outdoor
use, such as Type SJTW, 16AWG, and that has a
lower temperature rating of -40° F (-40° C).
•Ground Fault Circuit Interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) that will be used
for this Snow Shovel. For an extra measure of safety, use
a receptacle that has built-in GFCI protection.
•The nameplate on the Snow Shovel indicates the voltage
used. Do not connect the Snow Shovel to an AC circuit
that provides a different voltage from the voltage that is
indicated on the nameplate.
USING THE CORD RETAINER (Figure 3)
This Snow Shovel is equipped with a cord retainer in order
to prevent the extension cord from disconnecting from the
power cord while the Snow Shovel is in use.
•Prevent any possible disconnection of the power cord
from the extension cord while the Snow Shovel is in use
by using the cord retainer and guide bar. Refer to the
section entitled Using the Cord Retainer.
•Avoid accidental start-ups. Do not carry the Snow Shovel
with a finger on the switch while it is plugged in. Verify
that the switch is in the "OFF" position before plugging in
the Snow Shovel.
•Unplug the Snow Shovel and allow it to cool down before
putting it into storage. Store the Snow Shovel indoors.
•Unplug the Snow Shovel when it is not in use and before
performing any maintenance or repairs.the nameplate.
WARNING
Minimum Gauge for Extension Cords (AWG)
(when using 120 V only)
Cord retainer
FIGURE 3
8
•Keep the extension cord away from heat, oil, and sharp
edges in order to prevent damage.
In order to prevent electric shock, use an extension cord that is suitable for outdoor use.
To use the cord retainer:
1. Fold the extension cord to form a tight loop near the retainer.
2. Push the loop through the bottom hole in the retainer.
3. Slide the loop over the retaining clip, and pull down until
the cord is secured.
NOTE: Do not plug the extension cord into the outlet
until it has been connected to the cord retainer and
plugged into the Snow Shovel.
•Do not abuse the extension cord. Do not carry the Snow
Shovel by the power cord or pull on the cord in order to
disconnect it from the receptacle.
•If the extension cord is damaged in any manner while it is
plugged in, disconnect it from the outlet immediately.
WARNING
FIGURE 2
•Verify that the rotor and all moving parts have come to
a complete stop, and disconnect the Snow Shovel from
the power supply in order to prevent accidental start-ups
before cleaning or performing any inspections or repairs.
8 Amp Electric Snow Shovel Operator’s Manual
Amp Rating
More Than
Total Length of Cord in Feet (meters)
Not More Than
25' (7.6 m)
50' (15 m)
100' (30.4 m)
150' (45.7 m)
0
6
18
16
16
14
6
10
18
16
14
12
101216161412
12161412Not Recommended
Contact us at www.mantis.com
9
Storage & Transportation
Operation
STARTING THE SNOW SHOVEL (Figure 4-5)
STORAGE
Avoid accidental start-ups. Verify that the operator is in the
starting position when using the snow shovel. In order to
avoid serious injury, the operator and unit must be in a stable
position when starting the Snow Shovel.
•Store the Snow Shovel in a locked location in order to
prevent unauthorized use or damage.
Follow this sequence exactly in order to start the Snow Shovel.
1. Verify that the Snow Shovel is plugged in.
2. Press and hold the lock-out button.
3. While holding the lock-out button, press and hold the
trigger switch.
4. Hold the handles and begin to use the Snow Shovel.
•Allow the motor to cool down before storing.
•Store the Snow Shovel in a dry, well-ventilated area.
Lock-out
button
•Store the Snow Shovel out of the reach of children.
CLEANING
Use a small brush to clean the outside of the Snow Shovel. Do
not use strong detergents. Household cleaners that contain
aromatic oils such as pine and lemon, and solvents such as
kerosene can damage the plastic housing and handles. Wipe
off any moisture using a soft cloth.
NOTE: The Snow Shovel will not start if the lock-out
button is not held until the trigger switch is lifted.
WARNING
STOPPING THE SNOW SHOVEL
1. Release the trigger switch.
2. The lock-out button will pop out, and the Snow Shovel
will stop.
Trigger switch
FIGURE 4
USING THE SNOW SHOVEL
In order to avoid serious personal injury, turn the
Snow Shovel off and unplug it before cleaning or
servicing.
•St ar t the Snow Shovel by following the St ar ting
instructions. The depth and weight of the snow will
determine the forward speed.
TRANSPORTING THE SNOW SHOVEL (Figure
•Push the Snow Shovel forward so that it rides on the
scraper.
•Secure the Snow Shovel while transporting.
FIGURE 6
6)
•Allow the motor to cool down before transporting.
•When moving the Snow Shovel, grasp it by the top and
auxiliary handles.
•Verify that the power cord is attached to the cord retainer.
The power cord should trail to the side of the operator.
OPERATING TIPS
•Clear away the snow immediately after snowfall.
•For complete snow clearance, slightly overlap each
clearance pass.
•If possible, discharge the snow downwind.
•For safety and to prevent damage to the snow thrower,
keep the area to be cleared free of stones, toys and other
foreign objects.
FIGURE 5
AFTER USE
•Stop the motor.
•Disconnect the electric cable from the snow thrower and
the property’s power socket.
•Allow the snow thrower to cool for 30 minutes.
•Clean the inside and outside of the snow thrower with a
suitable brush.
•Check that there are no damaged or loose parts. Repair/
replace parts if necessary.
10
WARNING
The snow thrower must never be rinsed with water. Risk of damage to the electrical system and
risk of electric shocks.
8 Amp Electric Snow Shovel Operator’s Manual
Contact us at www.mantis.com
11
Maintenance
Maintenance
INSPECTING/REPLACING THE DRIVE BELT
REPLACING THE SCRAPER (Figure 9)
(Figure 7-8)
When servicing the Snow Shovel, use only the manufacturer's
original replacement parts. Inspect the drive belt for wear once
per year or every 50 hours of operation, whichever comes
first. If the drive belt needs to be replaced, follow these steps.
In order to avoid serious personal injury, turn off the Snow
Shovel and allow it to cool down. Unplug the Snow Shovel
before performing any maintenance.
1. Remove the ten (10) screws from the belt cover using a
phillips screwdriver (Figure 7). Remove 3 screws for the
impellar bracket shown in (Figure 8).
2. Pull the belt tensioner (idler arm) away from the drive
pulley. Remove the damaged or broken belt from the
impeller pulley and the drive pulley inside the housing.
Discard the belt in the proper manner (Figure 8) .
3. Loop the new belt around the drive pulley and the impeller
pulley (Figure 8). Pull the belt tensioner (idler arm) away
from the drive pulley in order to install the belt around
the drive pulley.
WARNING
In order to avoid serious personal injury, turn the
Snow Shovel off and unplug it before performing
any maintenance.
FIGURE 7
Use only the manufacturer's original replacement parts.
1. Place the Snow Shovel on the ground or on a work bench.
Position the Snow Shovel so that the impeller is facing up.
2. Remove the three (3) screws that are located beneath
the impeller that secure the scraper to the housing using
a phillips screwdriver. (Figure 8)
3. Remove the scraper, and discard it in the proper manner.
4. Snap the new scraper into position, and attach it to the
Snow Shovel by reinstalling the three (3) screws.
FIGURE 9
NOTE: Verify that the washer is still in place on the
impeller pulley shaft before reinstalling the belt cover.
4. Reinstall the belt cover with the ten (10) screws. Reinstall
the impellar pulley bracket three screws. In order to
facilitate the installation, position the narrow part of the
cover into the recess of the housing and install the two
top screws and then push the rest of the cover down into
recess and over the rotor shaft. Tighten all ten (10) screws.
WARNING
When fitting the belt back into the main housing,
verify that the belt is positioned to the right of the
Drive Belt Retainer. If the belt is positioned to the
left of the Drive Belt Retainer, serious damage
may occur.
12
8 Amp Electric Snow Shovel Operator’s Manual
FIGURE 8
Contact us at www.mantis.com
13
Maintenance
Maintenance
IMPELLOR REPLACEMENT
1
2
3
13
15
14
screw and washer
spring
•Remove the nut from the
left hand side of the impellor
shaft.
4
•Remove the 10 screws from
the side cover.
5
•Be sure not to lose the 2
springs.
6
•Place the impellor and shaft
back into the front scoop.
•Place the pulley back onto
the impellor shaft.
•Replace the 2 screws and 2
washers onto the impellor.
16
17
18
•Be sure to route the belt
correctly, as shown.
•R e p l a c e t h e 2 s p a c e r
washers on the impellor
shaft.
•Replace the pulley support
plate and the 3 retaining
screws.
19
20
21
spacer washer
•Remove the nut from the
impellor shaft.
7
•R e m o v e t h e 3 s c r e w s
holding the pulley support
plate.
•Remove the plate and the
two spacer washers.
9
8
screw and washer
•Remove the 2 screws and 2
washers.
10
impellor shaft washer and nut
•Remove the pulley and belt.
11
•Remove the impellor shaft
nut from the right hand side.
•Replace and tighten the
impellor shaft washer and
nut.
12
22
spring
•Place the upper spring into
position and then finger
tighten the cover plate into
place as shown.
spring
•P l a c e t h e l o w e r s p r i n g
into position and slide the
side cover up using slight
pressure to hold the spring
in place.
23
spacer washer
•Withdraw the impellor shaft
from the left hand side.
14
•Withdraw the old/damaged
impellor. Be sure to keep
the 2 spacer washers from
the right hand side of the
impellor.
•Insert the impellor shaft in
the new impellor and place
the 2 washers on the right
hand side.
8 Amp Electric Snow Shovel Operator’s Manual
•Replace and tighten the
remaining screws and the
nut and washer.
•Re-install the impellor shaft
nut and washer on the right
hand side, and tighten.
Contact us at www.mantis.com
15
Parts section
Parts section
16
8 Amp Electric Snow Shovel Operator’s Manual
Key
Qty.
Part No.
Description
Key
Qty.
Part No.
Description
1
1
36401263
Pigtail cable
38
1
3411298
Lower housing
2
1
3420102-1
Cord guard
39
1
3411798
Right cover
3
2
3220905
Screw
40
1
31102627
Motor assy.
4
2
3410302
Wire clip
41
1
3330498
Motor mounting bar
5
1
36301263-3 Switch assy.
42
2
3220475
Screw
6
1
34106263-5 Left upper handle
43
1
3410998-5
Rear housing
7
1
34107263-5 Right upper handle
44
1
31103627
Right grill assy.
8
1
34203625
45
1
31104627
Left grill assy.
9
1
34101185-2 Knob
46
1
3411275
Nylon tie
10
1
34105185-3 Auxiliary handle
47
1
33206623
Lower pole
11
1
3290205
Nut M6
48
1
3410835-4
Knob
12
20
36301623
Tube
49
1
32210625
Bolt
13
1
3640198-4
Cord
50
1
33205623
Upper pole
14
1
34201625
Rubber sealing ring
15
1
34202625
Protect pacer
16
1
3410801
Wire clip
17
1
3410898-5
Front housing
18
1
3330198
Spring
19
1
3111198
Tension wheel assy.
20
2
3390298
Spring
21
38
3220298
Screw
22
1
3330298
Left cover
23
1
3220998
Cover nut
24
2
3290499
Washer
25
1
3290198
Belt
26
1
3220236
Nut M10
27
1
3330198
Impeller pulley bracket
28
3
3220898
Washer
29
3
3220598
Screw
30
1
3111298A
Impeller pulley assy.
31
1
3320198
Impellor shaft
32
1
31105627
Impellor assy.
33
2
32206302A Screw
34
2
3290173
Washer
35
1
3412098A
Snow spade
36
3
3225599
Screw
37
1
32261198
Washer
Protect pacer
Contact us at www.mantis.com
17
Troubleshooting
Problem
Cause
remedy
1. The snow shovel does not start.
•
The Snow Shovel is unplugged.
•
Verify that the Snow Shovel is
plugged into an electrical outlet.
•
The lock-out button or trigger
switch were not used properly.
•
Press and hold the lock-out button,
and then lift and hold the trigger
switch (see the section entitled
Starting the Snow Shovel).
2. The motor is on, but the rotor does
not turn.
•
The belt is damaged.
•
Replace the belt (see the section
entitled Inspecting/Replacing the
Drive Belt).
3. The snow shovel leaves a thin
layer of snow behind.
•
The scraper is worn.
•
Replace the scraper (see the
section Replacing the Scraper).
LIMITED WARRANTY
MANTIS extends this limited warranty against defects in material and workmanship for a period of
five (2) years under normal usage for residential purposes and thirty (30) days under normal usage
for commercial purposes, from the date of purchase by the original purchaser.
MANTIS will repair or replace, at its option, any part or parts of the product found to be defective
in material or workmanship during the warranty period. Warranty repairs and replacements will be
made without charge for parts or labor. All parts replaced under warranty will be considered as part
of the original product, and any warranty on the replaced parts will expire coincident with the original
product warranty. If you think your MANTIS ELECTRIC SNOW SHOVEL is defective in material or
workmanship, you must send it, along with your proof of purchase (sales receipt) to:
Mantis
1028 Street Road
Southampton, PA 18966
You are responsible for pickup and delivery charges; the product must be returned to us postage paid.
MANTIS assumes no responsibility in the event that the product was not assembled or used in
compliance with any assembly, care, safety, or operating instructions contained in the Owner’s Manual or
accompanying the product. This limited warranty does not cover damages or defects due to normal wear
and tear, lack of reasonable and proper maintenance, failure to follow operating instructions or owner’s
manual, misuse, lack of proper storage or accidents [or routine maintenance parts and service]. This
limited warranty shall not be effective if your Mantis electric snow shovel has been subjected to negligence
or has been repaired or altered by anyone other than an authorized dealer or authorized service center.
You must maintain your MANTIS ELECTRIC SNOW SHOVEL by following the maintenance procedures described in the owner’s manual. Such routine maintenance, whether performed by you or a
dealer, is at yur expense.
MANTIS MAKES NO EXPRESS OR IMPLIED WARRANTIES, REPRESENTATIONS OR PROMISES
EXCEPT THOSE CONTAINED HEREIN. THERE ARE NO OTHER WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALL
WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH ABOVE ARE SPECIFICALLY
DISCLAIMED. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE DURATION OF THIS WRITTEN
LIMITED WARRANTY. MANTIS DISCLAIMS ALL LIABILITY FOR INDIRECT, INCIDENTAL AND/OR
CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE USE OF THE MANTIS PRODUCTS
COVERED BY THIS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THAT ABOVE LIMITATIONS AND EXCLUSIONS
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATES TO STATE.
MANTIS
1028 Street Road
Southampton, PA 18966
(215) 355-9700
18
8 Amp Electric Snow Shovel Operator’s Manual