RedMax EBZ7001-CA Specifications

2756-93110 (809)
OWNER / OPERATOR MANUAL
BACKPACK BLOWER
EB4300
WARNING
The engine exhaust from this product
contains chemicals known to the State
of California to cause cancer, birth
defects or other reproductive harm.
Thank you for purchasing a RedMax
product.
Before using our blower, please read
this manual carefully to understand the
proper use of your unit.
Read this manual periodically.
Read this manual carefully to understand all
safety precautions, controls, proper operation
and maintenance of your RedMax blower.
Failure to do so could result in serious injury.
SAFETY FIRST
Instructions contained in warnings within this manual and warning seals marked
with a
symbol on the blower concern critical points which must be taken into
consideration to prevent possible serious bodily injury, and for this reason you
are requested to read all such instructions carefully and follow them without fail.
Note that there may be times when warning seals peel off or become soiled and
impossible to read. If this happens, you should contact the dealer from which
you purchased the product to order new seals and affix the new seal(s) in the
required location(s).
■ Notes on types of warnings
WARNING
IMPORTANT
NOTE
Instructions labeled as shown at left, concern critical steps or
procedures which must be followed in order to prevent accidents
which could lead to serious bodily injury or death.This mark is
used to indicate instructions which must be followed without
exception.
Instructions labeled as shown at left concern steps or procedures
which, if not followed correctly, could lead to mechanical failure,
breakdown, or damage.
Used to label supplementary instructions designed to provide
hints or directions useful in the use of the product.
CONTENTS
SAFETY PRECAUTIONS · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
OPERATOR
USE OF BLOWER
WORKING CONDITION
AVOID NOISE PROBLEM
AVOID CHANCES OF DAMAGE
PARTS LOCATION & SPECIFICATIONS · · · · · · · · · · · · · · · · · 5
ASSEMBLY · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 5
BLOWER TUBE
FUEL · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 6
FUEL MIX
MIXING FUEL
FUELING
OPERATION · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 7
CONTROL ARM
STARTING ENGINE
ADJUSTING IDLE SPEED
STOPPING ENGINE
MAINTENANCE · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 8
AIR CLEANER
FUEL FILTER
SPARK PLUG
MUFFLER
SPARK ARRESTER
AIR INLET SCREEN
SHOULDER STRAP
STORAGE · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 10
PARTS LIST · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 11
Safety Precautions
• Read this Blower Owner/Operator Manual
carefully. Be sure you understand how to
operate this unit properly before you use
it. Failure to do so could result in serious
injury.
• Be sure to keep this manual handy so that
you may refer to it later whenever any
questions arise. Also note that you are
requested to contact the dealer from
whom you purchased the product for
assistance in the event that you have any
questions which cannot be answered
herein.
• Always be sure to include this manual
when selling, lending, or otherwise
transferring the ownership of this product.
• Please check and follow the local
regulations.
■ OPERATOR
• Refrain from operating the blower if you are
tired, ill, or upset, or if you are under the
influence of alcohol, drugs or medication.
• Clothing attire should consist of longsleeved shirt, long pants and proper
protective equipment. Do not wear a
necktie, scarf, muffler, or jewelry while
using the blower.
• If you have long hair, tie it up and put it
inside the head protection not to be
inhaled.
• Always wear eye protection goggles.
• Always wear ear protectors to protect your
ears from engine noise. If this guideline is
not followed, hearing loss can occur.
• Wear a face mask to guard against the
inhalation of dust.
• Wear anti-slip work gloves which can help
❲2 ❳
to grip the handle easier.
• Wear rubber-soled shoes or shoes with
some other form of anti-slip protection to
help protect you against falling.
• A person who is within a perimeter of 15m
(50ft) should wear the same proper
protective equipment as the user.
■ USE OF BLOWER
• Each time before starting the engine,
inspect the entire unit to see if every part is
in good order and is securely tightened in
place. If any damage is found in the fuel
line, the exhaust line, or the ignition wiring,
do not use the blower until it has been
repaired.
• Using the blower at top engine speed may
cause excessive noise. Be cautious of the
engine speed so not to cause a
disturbance to those around you.
IMPORTANT
• Before starting operation, always make
sure to check if any obstacles are left
inside the volute case. The obstacles may
cause damage to the fan and the volute
case, and also serious injury.
• Alert bystanders and neighbors to the
beginning of the work.
WARNING
Check to see if the shock-absorbing rubber
mount has become cracked or otherwise
damaged. Note that failing to replace this
rubber mount when it has become
cracked or damaged may cause the
engine to come loose from its frame
during use, thus resulting in possible
serious bodily injury.
• If cracked, be sure to replace without delay.
Safety Precautions
Observe and understand these safety precautions strictly.
Failure to do so could cause serious bodily injury or death.
WARNING
• Never use the blower without the screen
for the air intake of the blower. Before
each use, check that the screen is
attached in place and is free from any
damage.
• All engine service except for those
described in this manual should be
performed by competent service personnel.
Improper service to the blower fan and
muffler could cause a hazardous failure.
• Limit your working hours and take a break
periodically.
• Have a periodic checkup for hearing.
• If you feel sick or fatigue, go see a doctor
before operating any equipment.
■ WORKING CONDITION
WARNING
WARNING
• Never remove debris from the intake
screen while the engine is running.
Contact with rotating blower fan may
result in a serious personal injury.
• Do not allow children to use blower. Make
sure that each person you authorize to
operate the blower understands all of the
safety rules in this manual.
• Avoid using any accessory or attachment
other than those bearing the RedMax mark
for use with the blower.
• When suspending a job or inspecting the
blower, be sure to stop engine.
• Drain the fuel from the fuel tank before
transporting or storing the blower.
• When storing the blower, choose a space
indoors free from moisture and out of the
reach of children.
• Examine the blower at intervals for loose
fasteners and rusted or damaged parts.
• Use special care around the fuel line, the
muffler, and the ignition wiring.
• Keep open flames and sparks away from
the area where fuel is handled or stored, as
the fuel is highly flammable.
• Make sure that the engine has cooled down
before refueling.
• Mix and store fuel only in a approved
container.
• Never smoke while refueling the blower.
• Wipe off any spilled fuel and tighten the fuel
cap securely.
• Move at least 3m(10 ft) away from the
fueling spot before starting the engine.
• Check the work area that the blower will be
used in and remove or cover all valuables
that may be damaged by the air blast or
thrown debris.
• Avoid running the engine indoors. The
exhaust gases contain harmful carbon
monoxide.
❲3 ❳
Safety Precautions
• Keep operation area clear of all persons,
particularly small children and pets. Injury
may result from flying debris.
• Avoid using the blower where stable footing
and balance are not assured.
• Never to touch the spark plug or plug cord
while the engine is in operation. Doing so
may result in being subjected to an
electrical shock.
• Never to touch the muffler, spark plug, or
other metallic parts and covers of the
engine while the engine is in operation or
right after shutting down the engine. These
parts reach high temperatures during
operation and doing so could result in
serious burns.
■ AVOID NOISE PROBLEM
NOTE
Check and follow the local regulations
as to sound level and hours of
operations for blower.
• In general, operate blowers between
8a.m.and 5p.m.on week day and 9a.m.to
5p.m.weekends. Avoid using blower late at
night and/or early in the morning.
• Loosen compacted leaves, grass or debris
with a rake or broom beforehand, so that
the lowest possible throttle setting would
get the job done.
• In dusty conditions, slightly dampen
surfaces or use mister attachement when
water is available.
• Check if the air filter, air intakes and muffler
are working in properly.
• Never use more than one piece of the
blower at a time.
■ AVOID CHANCES OF DAMAGE
• Avoid directing the blower nozzle toward
persons, pets, cars, windows or anything
that could be harmed by blowing debris or
dust.
• Keep the nozzle at full extension when
operating so as to make the air stream
close to the ground.
• Collect any trash and leaves and put them
into a proper container after the job is
done.
• Always check to be sure that no debris has
been blown onto someone else’s property.
❲4 ❳
Parts Location & Specifications
MODEL EB4300
Dimensions ( L x W x H )
Dry Weight
Fuel Tank Capacity
Engine Type
Piston Displacement
Air Filter
Carburetor ( Diaphragm )
Ignition System
Spark Plug
Muffler
Operating Engine Speed
Fuel Consumption
Air Volume (w/std Pipes)
Air Volume (w/o Pipes)
Air Velocity
mm ( in )
kg ( lbs )
liter ( fl. oz )
cc ( cu. in )
valve type
rpm
liter/h ( fl. oz/h )
cu. m/min ( cfm )
cu. m/min ( cfm )
m/sec ( mph )
480 x 535 x 495 (189 x 211 x 195)
8.4 (18.4)
2.0 (67.6)
Air cooled 2-cycle gasoline engine
41.5 (2.53)
Regular size
Rotary
C.D.I
Champion RJ6C (Noise-proof)
Spark arrester equipped
2000 to 6500
1.7 (57.5)
12 (423)
16 (564)
72 (160)
Assembly
■ BLOWER TUBES
1.Connect the blower and swivel joint with
flexible hose. Clamp both ends of the
flexible hose securely with the hardware
supplied with the unit.
2.Align the protrusion and the groove
provided on the tube ends and twist the
tube until connection is locked up.
❲5 ❳
Fuel
WARNING
• Gasoline is very flammable. Avoid
smoking or bringing any flame or
sparks near fuel. Make sure to stop the
engine and allow it cool before
refueling the unit. Select outdoor bare
ground for fueling and move at least
3m(10ft) away from the fueling stop
before starting the engine. Or it could
lead to a fire.
■ FUEL MIX
Follow the instructions below strictly. Or
it could cause a mechanical failure.
• The engine is lubricated by oil mixed into
gasoline. Prepare a mixture of unleaded,
alcohol-free gasoline and RedMax oil or an
anti-oxidant added quality oil expressly
labeled for air-cooled 2-cycle engine use.
Recommended mixing ratio is 32 : 1
or 50 : 1 with RedMax JASO/ISO Oil.
• Do not mix fuels which have been left
unused for a period of one month or more.
• Make sure to use gasoline with a minimum
octane number of 90 ROZ(USA/Canada :
pump octane min.87)
• Unleaded gasoline is recommended to
reduce the contamination of the air for the
sake of your healths and the environment.
• Disqualified gasolines or oils may damage
sealing rings, fuel lines or fuel tank of the
engine.
• Exhaust emission are controlled by the
fundamental engine parameters and
components (eq., carburetion, ignition
timing and port timing) without addition
❲6 ❳
of any major hardware or the introduction of an inert material during combustion.
32:1 MIXING CHART
GASOLINE
gal. 1
2-CYCLE OIL fl.oz 4
2
8
3 4 5
12 16 20
• These engines are certified to operate
on unleaded gasoline.
■ MIXING FUEL
1.Measure out the quantities of gasoline and
oil to be mixed.
2.Put some of the gasoline into a clean,
marked fuel container.
3.Pour in all of the oil, cap the container and
shake it well.
4.Pour in the rest of gasoline and shake
again for one minute.
5.Indicate the contents on outside of
container to prevent with other containers.
DO NOT USE :
• Fuel containing no oil (raw gasoline)
may cause the engine becoming
overheated and damaged.
• Gasohol may cause deterioration of rubber
and plastic parts and disruption of the
engine lubrication.
• Oil for 4-cycle engine use or watercooled 2-cycle engine use may cause
spark plug fouling, carbon building-up and
piston ring sticking.
• Mixed fuels which have been left unused
for a period of one month or more may
have the carburetor clogged or result in the
engine failing to operate properly.
■ FUELING
1.Unfasten and remove the fuel cap. Put the
cap on a clean surface for dirt prevention.
2.Pour fuel into the fuel tank up to 80% of full
capacity.
3.Replace the fuel cap and tighten securely.
Spilled fuel must be wiped away from the
blower before starting the engine.
Operation
■ CONTROL ARM
1.Hold the upper end of the control arm in
hand and, while pulling it away from the
unit, rotate arm forward (anti-clockwise as
the arrow direction) until it clicks. To fold
the arm, reverse the order.
IMPORTANT
• Avoid pulling the starter rope out to its
full extension. Do not allow the starter
rope to snap back. Rewind the rope
slowly. This will prevent premature
damage to the starter.
• Do not let a person stand near the
blower or the exhaust port.
5.Once the engine is running, gradually open
the choke if it was set closed, and let the
engine run at idle speed for a minute to
warm it up.
■ STARTING ENGINE
IMPORTANT
• Avoid operating the blower with the
flexible tube and swivel joint
disconnected. That will reduce the
cooling air and the engine could be
damaged by overheating.
1.Push the primer bulb until fuel flows out in
the clear tube.
2.When the engine is cool, close the choke.
3.Set the throttle lever in 1/3 open position.
NOTE
• When the engine fails to start after several
attempts due to overchoking, open the
choke and repeat pulling the rope.
■ ADJUSTING IDLE SPEED
• The idling speed is set for 2000 rpm at the
factory. If it is necessary to adjust the idle
speed, use the adjustment screw on the
top side of carburetor.
■ STOPPING ENGINE
• Move the throttle lever to the idling position
and press the stop switch (red button) until
the engine comes to a complete stop.
4.To start, hold the top of the blower firmly
with your left hand. Pull the starter knob
slowly until you feel it engage and then
give it a vigorous strong pull.
❲7 ❳
Maintenance
WARNING
• Make sure that the engine has stopped
and is cool before performing any
service to the blower. Contact with
rotating blower fan or hot muffler may
result in a personal injury.
■ AIR CLEANER
• Never operate the blower without an air
filter or with a deformed or broken filter
element.
• C h e c k the air cleaner every 25 hours
of use or more frequently if used under
dusty conditions. A clogged air filter
may increase fuel consumption while
cutting down the engine power. Never
operate the blower without the air filter
or with a deformed filter element
because unfiltered dusty air will quickly
ruin the engine.
CLEANING AIR FILTER:
1.Remove the air cleaner cover by pulling
the tab on bottom and take out the filter
element.
2.Use neutral detergent and warm water to
clean the filter element. After cleaning, air
dry the element completely and moisten
with a small amount of motor oil.
3.Place the filter element into the air cleaner
housing and press the cover against the
housing until it clicks. Never forget to
attach the screen. If the screen is not
attached, the cleaner will not seal properly
and the dusts come into the cylinder.
❲8 ❳
■ FUEL FILTER
• A clogged fuel filter may cause poor
acceleration of the engine. Check
periodically to see if the filter is clogged
with dirt. The filter can be taken out of the
fueling port using a small wire hook.
Disconnect the filter assembly from the fuel
pipe and unhook the retainer to
disassemble it. Clean the components with
gasoline.
■ SPARK PLUG
• The spark plug may gather carbon deposits
on its firing end with reasonable use.
Remove and inspect the spark plug every
25 hours and clean the electrodes as
necessary with a wire brush. The spark gap
should be adjusted to .025 in.
• Plug manufacturers recommend replacing
the plug twice a year to avoid unexpected
plug failure in a job.
REPLACEMENT PLUG IS A CHAMPION
RJ6C OR THE EQUIVALENT, SUCH AS
BOSCH WR8E OR NGK BR6S.
IMPORTANT
• Note that using any spark plugs other than
those designated may result in the engine
failing to operate properly or in the engine
becoming overheated and damaged.
• To install the spark plug, first turn the plug
until it is finger tight, then tighten it a
quarter turn more with a socket wrench.
Maintenance
■ MUFFLER
Pay close attention to the precautions
below. Or it could cause an accident or a
fire.
WARNING
• Inspect periodically, the muffler for loose
fasteners, any damage or corrosion. If any
sign of exhaust leakage is found, do not
use the blower and have it repaired
immediately.
• Note that failing to do so may result in
the engine catching on fire.
■ AIR INLET SCREEN
IMPORTANT
• Before operating the blower, check that the
air inlet screen is attached in place, is free
from any damage and is not clogged with
dusts or obstacles.
IMPORTANT
• Before starting operation, always make
sure to check if the muffler is properly held
by three bolts to the cylinder. (Fastening
Torque : 80~120kg·cm)
• Even if one bolt out of three bolts is loose,
the muffler may get loose during operation
which may result in engine catching on fire.
■ SPARK ARRESTER
• The muffler is equipped with a spark
arrester to prevent red hot carbon from
flying out of the exhaust outlet. Periodically
inspect and clean as necessary with a wire
brush. In the State of California it is
required by law (Section 4442 of the
California Public Resources Code) to equip
a spark arrester when a gas powered tool
is used in any forest covered, brush
covered, or grass covered unimproved
land.
• Blowing air is taken in from the air inlet
screen. When air flow has dropped down
during operation, stop the engine and
inspect the air inlet screen for blocking by
obstacles.
• Note that failure to remove any such
obstacles may result in the engine
becoming overheated and damaged.
WARNING
• Never use the blower without the air
inlet screen. Before inspecting the
screen, stop the engine without fail.
Contact with rotating blower fan may
result in a serious personal injury.
❲9 ❳
Maintenance
■ SHOULDER STRAP
• If the shoulder strap is damaged it may
break during use, thus causing the product
to fall and resulting in personal injury.
Follow the instructions below to replace the
shoulder strap.
• Pass the top end of the strap through the
hanger, making the FLAPPED SIDE
OUTSIDE.
• Pull the end of the strap through the ring,
on the strap, and then push the ring
towards the hanger as close as possible.
Storage
BEFORE STORING THE BLOWER:
1.Drain a fuel tank and push the primer bulb
until it becomes empty of fuel.
2.Remove the spark plug and drop a
spoonful of 2-cycle oil into the cylider.
Crank the engine several time and replace
the plug.
❲ 10 ❳
WARNING
• The flap on the end of the strap works
as a stopper. Never install the strap with
the flapped side inside, or the unit may
fall from the operator, which could
result in injury to the operator and/or
damage to the unit.
NOTE
• Never use a blower which is not
properly repaired or remodeled.
Parts List
BACKPACK BLOWER
EB4300
NOTE :
1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or
replacement.
2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the
use of any parts other than those specified by the company.
3. When placing parts orders for repair and/or replacement, check if the model name and the
serial number are applicable to those specified in the parts list, then use parts number
described in the parts list.
4. The contents described in the parts list may change due to improvement.
5. The parts for the machine shall be supplied seven (7) years after the machine is
discontinued. [It is possible that some specific parts may be subject to change of their
delivery term and list price within the limit of ten (7) years after the machine is
discontinued. It is also possible that some parts may be available even after the limit of
seven (7) years.]
❲ 11 ❳
Parts List : EB4300
Fig.1 CARBURETOR COMPONENTS
Carburetor Ass’y P/NO. 3407-81000
❲ 12 ❳
EB4300
Fig.1 CARBURETOR COMPONENTS
Key#
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26*
27*
1850-81450
3306-81380
3356-81310
1850-81270
1850-81220
3310-81250
3310-81230
1850-81490
1850-81520
1751-81510
5500-81160
1881-81140
1751-81130
1065-81410
1065-81420
1850-81470
3310-81260
1752-81110
5500-81120
1751-81180
1918-81170
1881-81130
1850-81530
3407-81250
1751-81240
—————
—————
Description
Body ass’y
Screen
Valve
Spring
Screw
Pin
Lever
Body
Cover
Pump
Washer
Swivel
Ring
Gasket
Diaphragm
Gasket
Diaphragm
Screw
Bracket
Nut
Screw
Ring
Screw
Jet
O-Ring
Body
Valve ass’y
Q'ty
Key#
Part Number
Description
Q'ty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
4
1
1
1
1
[NOTE]
• 26*-Body and 27*-Valve ass’y are not supplied
as an individual part respectively, but supplied
as a carburetor ass’y (P/NO. 3407-81000).
❲ 13 ❳
Parts List : EB4300
Fig.2 ENGINE GROUP
❲ 14 ❳
EB4300
Fig.2 ENGINE GROUP
Key#
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1490-12113
2756-12210
3495-12280
1484-13160
2756-13120
2756-13130
0263-90535
1491-32110
2750-12520
2756-15100
1421-15120
2750-15210
2750-15160
2750-15170
2756-21100
2756-21140
2810-21240
1520-21220
1400-21220
01252-30530
04065-03515
2750-21210
1565-72211
1483-41111
1400-41220
1490-41310
3350-41320
1400-41410
2616-41510
2756-42000
1300-42410
1400-43230
1000-43240
2750-71110
2750-71200
2750-72150
1900-72111
1900-72120
5500-72130
1497-73110
41
42
43
44
45
2756-71220
2756-73200
1487-75100
1180-75221
1487-75120
Description
Cylinder
Gasket, base
Bolt
Insulator
Gasket
Gasket
Screw
Cover
Bolt
Muffler ass’y
Arrester
Gasket
Bolt
Bolt
Crankcase comp
Gasket
Bearing
Oil seal
Oil seal
Bolt
Snap ring
Cover
Bolt
Piston
Ring
Piston pin
Snap ring
Bearing
Washer
Crankshaft comp
Shim
Nut
Key
Rotor
Coil ass’y
Bolt
Cap
Spring
Grommet
Spark plug
Q'ty
Key#
Part Number
Description
Q'ty
1
1
4
1
1
1
2
1
2
1
1
1
2
1
1
1
3
1
1
4
1
1
1
1
2
1
2
1
2
1
0~1
2
1
1
1
2
1
1
1
1
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
1487-75140
1861-75150
1483-75270
1487-75160
1487-75170
1400-75160
1400-75170
1487-75211
3460-75510
2756-75610
3407-81000
3407-82102
3407-82130
3407-82140
2630-33610
1487-82200
1487-82210
1491-82311
1484-82510
0263-90560
1491-82352
1491-82360
1133-82060
2750-21510
Dog
Washer
Screw
Retainer
Washer
Rope
Knob
Pulley
Bolt
Label
Carburetor
Body ass’y
Plate
Lever
Screw
Cover ass’y
Knob
Element
Plate
Screw
Screen
Screw
Label
Bolt
1
1
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
2
1
1
1
6
101
102
103
104
105
106
2756-05010
2756-06010
2750-96100
3350-96220
3350-96230
2750-96240
Short block
Gasket kit
Puller ass’y
Stopper
Guide
Gauge
OP
OP
OP
OP
OP
OP
(Champion RJ6C)
Cap
Cord comp
Recoil ass’y
Spring
Reel
1
1
1
1
1
❲ 15 ❳
Parts List : EB4300
Fig.3 BLOWER GROUP
❲ 16 ❳
EB4300
Fig.3 BLOWER GROUP
Key#
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
2750-31110
2750-31210
2750-31150
3490-11150
07000-02095
2750-31420
3310-53331
2750-31310
2750-31150
1140-72231
3407-16120
2750-31290
2750-31510
3407-12210
2750-31612
2750-31150
2756-32100
3490-21120
3460-21311
3495-21320
2756-32300
2750-32510
2750-32520
2750-32530
2750-32540
2750-32610
2750-32620
2756-85100
4500-85200
5600-85250
4500-85220
4500-85230
5600-85240
2750-85300
3302-85400
1260-85460
3407-23610
1100-86120
3407-25000
3495-25110
3310-53331
01642-20508
3495-25212
3495-25310
3495-25410
3495-25420
Description
Volute case
Volute cover
Screw
Elbow
O-Ring
Screw
Nut
Cover inlet
Screw
Clamp
Screw
Tube
Fan
Bolt
Engine cover
Screw
Frame comp
Ring
Pad
Clip
Band ass’y
Damper, upper
Washer
Screw
Bolt
Damper, lower
Nut
Tank ass’y
Cap ass’y
Valve
Packing
Holder
Cap
Pipe comp
Filter
Clip
Screw
Clip
Lever set
Lever
Nut
Washer
Arm
Bracket
Bolt
Spring
Q'ty
Key#
Part Number
1
1
9
1
1
2
2
1
3
1
1
1
1
4
1
4
1
2
1
4
2
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
3495-25440
01584-00605
3495-25450
3495-25510
3407-83110
3495-25810
2750-32540
2750-31910
2750-51110
2750-51200
6811-51210
6811-51220
2756-51510
2756-51520
2750-51500
3495-51420
3495-51430
3238-15230
3407-91000
3540-91120
3407-91130
101
102
103
3495-51201
3495-51321
3495-51331
Description
Washer
Nut
Washer
Switch
Cable comp
Tube
Bolt
Label
Hose
Swivel joint
Pipe, straight
Pipe, end
Clamp
Clamp
Grip ass’y
Wing bolt
Wing nut
Washer
Tool set
Spanner
Socket
Joint
Pipe
Pipe
Q'ty
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
OP
OP
OP
❲ 17 ❳
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
THE CALIFORNIA AIR RESOURCES BOARD AND KOMATSU ZENOAH Co. ARE PLEASED TO
EXPLAIN THE EMISSION CONTROL SYSTEM WARRANTY ON YOUR 1995 AND LATER LAWN AND
GARDEN EQUIPMENT ENGINE. IN CALIFORNIA, NEW UTILITY AND LAWN AND GARDEN
EQUIPMENT ENGINES MUST BE DESIGNED, BUILT AND EQUIPPED TO MEET THE STATE'S
STRINGENT ANTI-SMOG STANDARDS.
KOMATSU ZENOAH Co, MUST WARRANT THE EMISSION CONTROL SYSTEM ON YOUR LAWN AND
GARDEN EQUIPMENT ENGINE FOR THE PERIODS OF TIME LISTED BELOW PROVIDED THERE HAS
BEEN NO ABUSE, NEGLECT OR IMPROPER MAINTENANCE OF YOUR LAWN AND GARDEN
EQUIPMENT ENGINE.
YOUR EMISSION CONTROL SYSTEM. MAY INCLUDE PARTS SUCH AS THE CARBURETOR, THE
IGNITION SYSTEM, AND CATALYTIC CONVERTER. ALSO INCLUDED MAY BE THE HOSES, BELTS,
CONNECTORS AND OTHER EMISSION-RELATED ASSEMBLIES.
WHERE A WARRANTABLE CONDITION EXISTS, KOMATSU ZENOAH Co. WILL REPAIR YOUR LAWN
AND GARDEN EQUIPMENT ENGINE AT NO COST TO YOU INCLUDING DIAGNOSIS, PARTS AND
LABOR.
MANUFACTURER'S WARRANTY COVERAGE:
THE 1995 AND LATER UTILITY AND LAWN AND GARDEN EQUIPMENT ENGINES ARE
WARRANTED FOR TWO YEARS. IF ANY EMISSION-RELATED PART ON YOUR ENGINE IS
DEFECTIVE, THE PART WILL BE REPAIRED OR REPLACED BY KOMATSU ZENOAH Co.
OWNER'S WARRANTY RESPONSIBILITIES:
—AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER, YOU ARE RESPONSIBLE FOR
THE PERFORMANCE OF THE REQUIRED MAINTENANCE LISTED IN YOUR OWNER'S
MANUAL. KOMATSU ZENOAH Co. RECOMMENDS THAT YOU RETAIN ALL RECEIPTS
COVERING MAINTENANCE ON YOUR LAWN AND GARDEN ENGINE, BUT KOMATSU
ZENOAH Co. CAN NOT DENY WARRANTY SOLELY FOR THE LACK OF RECEIPTS OR FOR
YOUR FAILURE TO ENSURE THE PERFORMANCE OF ALL SCHEDULED MAINTENANCE.
—AS THE LAWN AND GARDEN EQUIPMENT ENGINE OWNER, YOU SHOULD BE AWARE,
HOWEVER, THAT KOMATSU ZENOAH Co. MAY DENY YOU WARRANTY COVERAGE IF
YOUR LAWN AND GARDEN EQUIPMENT ENGINE OR A PART HAS FAILED DUE TO ABUSE,
NEGLECT, IMPROPER MAINTENANCE OR UNAPPROVED MODIFICATION.
—YOU ARE RESPONSIBLE FOR PRESENTING YOUR LAWN AND GARDEN EQUIPMENT
ENGINE TO A KOMATSU ZENOAH Co. DISTRIBUTION CENTER AS SOON AS A PROBLEM
EXISTS. THE WARRANTY REPAIRS SHOULD BE COMPLETED IN A REASONABLE AMOUNT
OF TIME, NOT TO EXCEED 30 DAYS.
IF YOU HAVE ANY QUESTIONS REGARDING YOU WARRANTY RIGHTS AND RESPONSIBILITIES,
YOU SHOULD CONTACT KOMATSU ZENOAH AMERICA INC. AT (770)-381-5147.
Red Max BLOWERS
MODEL EB4300
2-YEAR LIMITED WARRANTY
EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE MODEL
EB4300 UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR
OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR
PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE:
THE CARBURETOR ASSY, COIL ASSY, ROTOR, SPARKPLUG,
AIR FILTER, FUEL FILTER, INTAKE MANIFOLD, AND THE GASKETS
ALL OTHER PARTS EXCEPT ABOVE PARTS, FOR TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER
USE ] FROM THE DATE OF ORIGINAL ANY DELIVERY OF THE MODEL EB4300 UNIT, THE COMPANY, THROUGH ANY
RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL PURCHASER, ANY PART
OF PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. THIS IS THE EXCLUSIVE REMEDY.
THE PURCHASER SHALL BEAR COSTS OF TRANSPORTING THE UNIT TO AND FROM THE RedMax DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAGNOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAGNOSTIC WORK IS PERFORMED AT THE RedMax DEALER.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OPERATOR MANUAL.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION TO THE EFFECT OF "REPAIR OR REPLACE AS
NECESSARY" SHALL BE WARRANTED FOR THE WARRANTY PERIOD.ANY WARRANTED PART WHICH IS
TIME UP TO THE FIRST SCHEDULED REPLACEMNET POINT FOR THE PART.
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PERFORMANCE AND DULABILITY MAY BE USED IN NONWARRANTY MAINTENANCE OR REPAIRS, AND SHALL NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER ENGINE COMPONENTS CAUSED BY THE FAIRURE OF A
WARRANTED PARTS STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF
INSTRUCTION LISTED IN THE OWNER/OPERATOR MANUAL FOR PROPER USE AND MAINTENANCE OF THE UNITS,
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IMPROPER LUBULICATION, USE OF ANY PARTS OR ACCESSARIES
OTHER THAN THOSE SPECIFIED BY THE COMPANY, OR OTHER CAUSES BEYOND THE CONPANY'S CONTROL.
THIS WARRANTY DOES NOT COVER THOSE PARTS REPLACED BY NORMAL WEAR OR HARMLESS CHANGES IN
THEIR APPEARANCE.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE LIMITED TO TWO (2) YEARS OF HOME USE [ ONE (1) YEAR FOR ANY OTHER USE ] FROM THE ORIGINAL
DELIVERY DATE.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL DAMAGE UNDER ANY AND ALL WARRANTIES
ARE EXCLUDED.
SOME STATES DO NOT ALLOW LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMINATION OR EXCLUSION MAY
NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
IF YOU NEED TO OBTAIN INFORMATION ABOUT THE NEAREST SERVICE CENTER, PLEASE CALL KOMATSU
ZENOAH AMERICA INC. AT (770)-381-5147.
IMPORTANT: YOU WILL RECEIVE A WARRANTY REGISTRATION CARD AT TIME OF PURCHASE.PLEASE FILL
OUT THE CARD AND SEND IT TO RedMax / KOMATSU ZENOA AMERICA WITHIN SEVEN (7) DAYS.BE SURE TO KEEP
A COPY FOR YOUR RECORDS.
KOMATSU ZENOAH AMERICA INC.
1505 Pavilion Place Suite A
Norcross, Georgia 30093
KOMATSU ZENOAH AMERICA INC.
1505 Pavilion Place Suite A
Norcross, Georgia 30093