Hampton Bay Y35046-163 Instructions / Assembly

ASSEMBLY AND INSTALLATION (Continued)
Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY GROUND WIRE (8) using a
WIRE CONNECTOR (13). Place wiring and connections inside the OUTLET BOX (1). (See Fig. 1)
CHAIN PENDANT FIXTURE
INSTALLATION INSTRUCTIONS
6. Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17). Place the CANOPY (15)
over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16) onto the
SCREW COLLAR LOOP (6). (See Fig. 1)
7. Screw the BOTTOM FOUNT (19) to COUPLING (21) at the bottom.slide the CANDLE COVER (22) onto
the socket .
Please read carefully and save these instructions, as you may need them at a later date.
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
8. Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage specified
on the fixture’s wattage rating label.
INSTALLATION IS NOW COMPLETED
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
FIG. 1
FIG. 2
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
ASSEMBLY AND INSTALLATION
1. Take the parts out of the mounting package and thread both 1/8” IPS HEX NUTS (5) several turns onto each end of
the NIPPLE (4). Screw the end of the NIPPLE (4) several turns into the threaded hole of the MOUNTING
BRACKET (2) but do not tighten the 1/8” IPS HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11) and the
SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING BRACKET (2)
assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING BRACKET (2) and the MOUNTING
SCREWS (3) provided. (See Fig. 1)
2. Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY (15) over the
OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the midpoint of the outside
threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface of the CANOPY (15). Remove
the CANOPY (15) and tighten both 1/8” IPS HEX NUTS (5) down on the MOUNTING BRACKET (2) and the
SCREW COLLAR LOOP (6). (See Fig. 1)
3. Extend the ARMS (20) until they are all evenly spaced. Open up the end links of the CHAIN (17) and attach one end
of the CHAIN (17) onto the FIXTURE LOOP (18). Slide the THREADED RING (16) and the CANOPY (15) onto
the CHAIN (17) (in that order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6).
Close the ends of the chain links. (See Fig. 1 & 2)
4. Unravel the fixture lead wires and FIXTURE GROUND WIRE (7) and thread them through every other link of the
CHAIN (17) starting with the chain link attached to the FIXTURE LOOP (18). Feed the fixture lead wires and
FIXTURE GROUND WIRE (7) through the SCREW COLLAR LOOP (6) and NIPPLE (4) assembly. Pull the
fixture lead wire and the FIXTURE GROUND WIRE (7) upward to remove any excess slack. (See Fig. 1)
5. Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9) to the
SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED FIXTURE LEAD
WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND SCREW (14) of the MOUNTING
BRACKET (2). (Note: Be sure to provide an extra 3” length of the GROUND SCREW (14).
1.
2.
3.
4.
5.
6.
7.
8.
OUTLET BOX
MOUNTING BRACKET
MOUNTING SCREW
NIPPLE
1/8” IPS HEX NUT
SCREW COLLAR LOOP
FIXTURE GROUND WIRE
SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
10. SMOOTH FIXTURE LEAD WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. BOTTOM FOUNT
20. ARM
21. COUPLING
22. CANDLE COVER