Hampton Bay ES4761OB4-B Installation Guide

Item #**********
Model #ES4761OB4-B
Safety Information
Pre-Installation
IMPORTANT SAFETY INSTRUCTIONS
(Save These Instructions)
TOOLS REQUIRED
□ Read all instructions prior to beginning the
USE AND CARE GUIDE
PENDANT FIXTURE
installation process.
□ Make sure the power is turned off at the
electrical panel box before beginning your
installation. Turning the power off at the wall
switch is not sufficient to prevent electrical
shock.
□ This fixture is intended to be mounted to a 4 in.
square x 2-1/8 in. deep metal octagon outlet box.
The box must be directly supported by the
building structure.
□ All electrical connections must be in accordance
with local codes and the National Electrical Code.
If you are unfamiliar with methods of installing
electrical wiring, secure the services of a
qualified licensed electrician.
WARNING: Do not install this lighting
system in a wet location.
2 Attaching the canopy to the straight rod
A
□ Thread the fixture wires up through the canopy (A).
□ Screw the rod assembly into the canopy (A).
Ladder
Gloves
Safety goggles Phillips screwdriver Electrical tape
Wirestripper
HARDWARE INCLUDED
CAUTION: Turn off/unplug the light and
allow it to cool before replacing the bulb.
CAUTION: Keep the lamp away from
materials that may burn.
NOTE: Hardware not shown to actual size.
the threaded rod assembly
3 Installing
and bulb
AA
BB
Outlet box screws Wire connectors
x2
x3
FF
EE
DD
CC
Mounting bracket Decorative nut Steel washer Diffuser nut
x1
x1
x2
assembly
x1
E
□ Secure the threaded rod assembly (D) to the fabric
shade (E), and tighten it using the hex nut on the
threaded rod assembly (D).
□ Install the light bulbs (sold separately).
CAUTION: Refer to the re-lamping label located on
the fixture. Do not exceed the recommended wattage.
Care and Cleaning
D
Installation
1 Assembling the rods
CAUTION: Do not use chemical solvents or harsh
abrasives to clean the fixture or components, as damage
may occur.
THANK YOU
Installation
□
□ To clean the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by
removing the fuse at the fuse box.
□ Use a dry or slightly dampened, clean cloth (use clean water, never use a solvent) to wipe the
interior and exterior surfaces of the xture.
□ Allow the fixture to dry completely before power is restored.
C
Screw the rods (B,C) together to form one
long rod.
B
4 Installing the diffuser
E
□ Place the diffuser (F) and the steel washer (EE) onto
the threaded rod assembly (D), and secure them with
the diffuser nut (FF).
We appreciate the trust and confidence you have placed in Hampton Bay through the purchase of this pendant fixture.
We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of
products available for your home improvement needs. Thank you for choosing Hampton Bay!
D
F
Warranty
Pre-Installation
5-YEAR LIMITED WARRANTY
PACKAGE CONTENTS
Installation
of five year(s) from the date of purchase. If within this period the product is found to be defective in material
or workmanship, the product must be returned, with a copy of the bill of sale as proof of purchase, to the
original place of purchase. The manufacturer will, at its option, repair, replace, or refund the purchase price
B
excludes liability for direct, incidental, or consequential damages. Some states do not allow exclusions
or limitations on an implied warranty, so the above exclusions and limitations may not apply. This warranty
Installation
5 Installing the mounting bracket assembly
A
FF
EE
Outlet box
□ Make sure the power is off.
□ Pull the supply wires down out of the outlet box.
□ Remove the pre-assembled decorative nuts (DD)
from the mounting bracket assembly (CC).
□ Attach the mounting bracket assembly (CC) to the existing
outlet box with the outlet box screws (AA) provided.
CC
AA
7 Attaching the canopy to the ceiling
□ Raise the canopy (A) up to the outlet box.
□ Secure the canopy (A) to the mounting bracket
assembly (CC) using the decorative nuts (DD) provided.
□ Adjust the length of the mounting bracket assembly (CC)
studs and hex nuts if necessary.
CC
A
DD
DD
Contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
D
E
F
Questions, problems, missing parts? Before returning to store,
call Commerial Electric Customer Service
8 a.m. - 6 p.m., EST, Monday - Friday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.
Part
Description
Quantity
A
Canopy
1
B
Short straight rod (6 in.)
1
C
D
E
F
Long straight rod (12 in.)
Threaded rod assembly (7 in.)
Fabric shade assembly
Diffuser
2
1
1
1
C
Troubleshooting
6 Making the electrical connections
□ Attach the ground wire from the outlet box to the ground
screw on the mounting bracket (CC), which is green and
marked "GND".
□ Connect the negative wires (raised ribs without writing)
from the fixture to the negative wires from the supply
circuit, the positive wires (smooth with writing) from the
fixture to the positive wires from the supply circuit, and the
ground wire (bare) from the fixture to the ground wire from
the supply circuit using the wire connectors (BB).
□ Wrap electrical tape (not included) around the wire
connectors (BB), and ensure they are secure.
□ Push all excess wire and wire connections back
into the outlet box.
BB
CC
Problem
Possible Cause
Solution
The light bulb will not
illuminate.
The light bulb is burned
out.
Replace the light bulb.
The power is off.
Make sure the power supply is on.
There is a faulty wire
connection.
Check the wiring.
Contact a quali ed and licensed
electrician if you are not comfortable
troubleshooting wiring problems.
There is a faulty switch.
Test or replace the switch.
There are crossed wires,
The fuse blows or the circuit
breaker trips when the light bulb or the power wire is not
properly grounded.
is illuminated.
Check the wire connections.