Hampton Bay 21343-018 Installation Guide

TROUBLESHOOTING:
Bulb will not light
Fuse blows or circuit
breaker trips when light
is turned on
Possible Cause
Corrective Action
1. Bulb is burned out
1. Replace light bulb
2. Switch is off
2. Make sure switch is on
3. Faulty wire connection
3. Check wiring
Crossed wires or power
wire is grounding out
Check wire connections
INSTRUCTION MANUAL
INTERIOR 3-LIGHT PENDANT
HALINA
HOME DEPOT SKU 599-504 | S/O: 427-219 (UPC 773546217415)
CHROME FINISH
PRODUCT MAINTENANCE:
1. To clean the outside of the lamp, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the lamp.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning
off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
shade and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not limited to any labor
expense costs involved in the replacement or repair of said product.
Page 8
Page 1
Thank you for purchasing this Hampton Bay interior decorative lighting. This product
has been manufactured with the highest standards of safety and quality.
INSTALLATION
White Wire
Ground Wire
Black Wire
18. Junction Box
(not included)
FEATURES:
Adding shimmer and sparkle to your decor, the jewel-like crystal accents of this fixture
will be reflected in the light coming from within. Flowing arms uphold the candlestick
style bulb holder and fabric lampshades.
19. Wire Nut (x3)
QUESTIONS, PROBLEMS, MISSING PARTS:
15. Cross Bar
Before returning to your local Home Depot, please call our Customer Service
Team at 1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU 599-504 or (UPC 773546217415).
17. Ground Screw
21. Outlet Box Screw (x2)
16. Lock Nut
14. Nipple
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect
the power by turning off the circuit breaker or by removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
20. Canopy
3. If you have any non-electrical question about this fixture, please contact our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU 599-504 or (UPC 773546217415).
13. Canopy Loop
4. Keep your receipt and these Instructions for Proof of Purchase.
12. Loop Ring
Figure #1
Page 2
WHITE OR RIBBED
WHITE OR RIBBED
FROM HOUSE
FROM FIXTURE
BLACK (OR RED) WIRE
BLACK OR SMOOTH
FROM HOUSE
FROM FIXTURE
GROUND WIRE
GROUND WIRE
FROM HOUSE
FROM FIXTURE
Page 7
ADDITIONAL PARTS FOR INSTALLATION (included):
12. Loop Ring
17. Ground
Screw
13. Canopy
Loop
14. Nipple
19. Wire Nut
(x3)
20. Canopy
15. Cross Bar
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
16. Lock Nut
Safety goggles
Wire Strippers
Wire Cutters
Flathead
Screwdriver
Phillips
Screwdriver
Electrical Tape
Ladder
B10 Bulb 40W Max
(not included) (x3)
21. Outlet Box
Screw (x2)
INSTALLATION INSTRUCTIONS:
1. Turn off power at main fuse box.
2. Install cross bar (15) assembly complete with nipple (14) and canopy loop (13) to
junction box (18) with outlet box screws (21) as one complete assembly.
3. Remove loop ring (12) from canopy loop (13). Slip canopy (20) over loop (13) and
secure by fastening loop ring (12). Adjust the height of the nipple (14) so canopy will sit
flat against ceiling and tighten locknut (16) against crossbar (15).
ADDITIONAL PARTS FOR ASSEMBLY (included):
4. Remove loop ring (12) and canopy (20) from ceiling.
5. Hold chandelier up against canopy loop (13) with chain and adjust to desired height.
Remove excess chain.
1. Crystal trim (x4)
6. Before tightening chain onto canopy loop (13), weave chandelier wire through every
second link.
2. Finial (x3)
3. Decorative Arm
(x3)
7. Candle Sleeve
(x3)
7. Let the canopy loop ring (12) slip to the bottom of chain. Repeat this step for canopy (20).
8. Secure chain onto canopy loop (13).
11. Chain loop
9. Weave wire through the canopy loop and into junction box.
10. Install both ground wires of chandelier (one from the canopy and one from the fixture)
to ground screw or ground wire of junction box or ground screw (17) on crossbar.
(Ref. Fig.1)
11. Connect black wire of power supply to the smooth side of the wire (flexible cord) from
the chandelier and connect white wire of power supply to the ribbed side of the wire
from the chandelier. (Ref. Fig.1)
NOTE: Always use wire nuts (19) or marrettes (included) to connect wires and push
all excess wire and connections back into junction box.
12. Lift canopy up to ceiling covering junction box and secure by using canopy loop ring.
Page 6
Page 3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture; lay out all parts on clean surface.
2. Tighten chain loop (11) onto fixture main body.
ASSEMBLY:
20. Canopy
13. Canopy Loop
12. Loop Ring
GLASS AND BULB INSTALLATION:
1. Install metal candle sleeves (7) over socket.
2. Install bottom socket finials (2) and finish by hanging decorative crystal trim (1)
onto each finial (2).
3. Install 40W max B10 chandelier bulbs (not included) (8).
11. Chain loop
10. Arms
9. Fabric Shade
8. B10 40W Bulb
(not included)
7. Candle Sleeve (x3)
3. Decorative Arm (x3)
2. Finials (x3)
1. Crystal Trim (x4)
Page 4
Page 5