Hampton Bay 12112-029 Installation Guide

TROUBLESHOOTING:
Bulb will not light
Fuse blows or circuit
breaker trips when light
is turned on
Possible Cause
Corrective Action
1. Bulb is burned out
1. Replace light bulb
2. Switch is off
2. Make sure switch is on
3. Faulty wire connection
3. Check wiring
Crossed wires or power
wire is grounding out
Check wire connections
INSTRUCTION MANUAL
INTERIOR 12-LIGHT CHANDELIER
GLASGOW
HOME DEPOT SKU 886-501 S/O 127-408 (UPC 773546175456)
BLACK FINISH
PRODUCT MAINTENANCE:
1. To clean the outside of the lamp, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the lamp.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning
off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
shade and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not limited to any labor
expense costs involved in the replacement or repair of said product.
Page 8
Page 1
Thank you for purchasing this Hampton Bay interior decorative lighting. This product
has been manufactured with the highest standards of safety and quality.
FEATURES:
INSTALLATION :
1. Junction Box
(not included)
Ground Wire
White Wire
Black Wire
2. Wire Nut (x3)
An assiduous parity of heavy ironwork with delicate composition are the origin of this
benevolent classic.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service
Team at 1-877-527-0313 or visit www.homedepot.com. Please reference your
SKU# (886-501) UPC# (773546175456).
5. Ground Screw
3. Cross Bar
6. Lock Nut
7. Nipple
4. Outlet Box Screw (x2)
CAUTION:
8. Canopy Loop
1. Before starting installation of this fixture or removal of a previous fixture, disconnect
the power by turning off the circuit breaker or by removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
3. If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU# (886-501) or UPC# (773546175456).
9. Canopy
4. Keep your receipt and these Instructions for Proof of Purchase.
Figure #1
Page 2
WHITE OR RIBBED
WHITE OR RIBBED
FROM HOUSE
FROM FIXTURE
BLACK (OR RED) WIRE
BLACK OR SMOOTH
FROM HOUSE
FROM FIXTURE
GROUND WIRE
GROUND WIRE
FROM HOUSE
FROM FIXTURE
Page 7
PARTS ADDITIONAL PART FOR INSTALLATION (included):
2. Wire Nut (x3)
7. Nipple
3. Crossbar
8. Canopy Loop
4. Outlet Box
Screws (x2)
9. Canopy
5. Ground Screw
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
6. Lock Nut
Safety goggles
Wire Strippers
Phillips
Screwdriver
Electrical Tape
Wire Cutters
Flathead
Screwdriver
10. Loop Ring
INSTALLATION INSTRUCTION:
1. Turn off power at main fuse box.
2. Install cross bar (3) assembly complete with nipple (7) and canopy loop (8) to junction
box (1) as one complete assembly.
3. Remove loop ring (10) from canopy loop (8). Slip canopy (9) over loop (8) and secure
by fastening loop ring (10). Adjust the height of the nipple (7) so canopy (9) will sit flat
against ceiling and tighten lock nut (6) against cross bar (3).
Ladder
B10 Bulb 60W max.
(not included) (x12)
ADDITIONAL PARTS FOR ASSEMBLY (included):
4. Remove loop ring (10) and canopy (9) from ceiling.
5. Hold chandelier up against canopy loop (8) with chain and adjust to desired height.
Remove excess chain.
11. Chain Loop
13. Center Column 14. Fixture Decorative 15. Decorative
Loop (x4)
Loop Screw (x8)
16. Decorative
Bottom Hub
17. Bottom Nipple
6. Before tightening chain onto canopy loop (8), weave chandelier wire through every
second link.
7. Let the canopy loop ring (10) slip to the bottom of chain. Repeat this step for canopy (9).
8. Secure chain onto canopy loop (8).
9. Weave wire through the canopy loop (8) and into junction box (1).
18. Hex Nut
19. Decorative
Finial
10. Install both ground wires of chandelier (one from the canopy (9) and one from the
fixture) to ground screw (5) or ground wire of junction box (1) or ground screw (5) on
cross bar (3). (See Fig. 1)
11. Connect black wire of power supply to the smooth side of the wire (flexible cord) from
the chandelier and connect white wire of power supply to the ribbed side of the wire
from the chandelier. (See Fig. 1)
NOTE: Always use wire nuts (2) or marrettes (included) to connect wires and push all
excess wire and connections back into junction box (1). (See Fig. 1)
12. Lift canopy (9) up to ceiling covering junction box (1) and secure by using canopy loop
ring (10).
Page 6
Page 3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture; lay out all parts on a clean surface.
ASSEMBLY:
2. Install chain loop (11) on center column (13).
3. Tighten column (13) onto the central hub of the fixture body.
4. Place decorative loop (14) onto the center column hooks (12), then secure to fixture
body with decorative loop screws (15).
10. Loop Ring
11. Chain Loop
12. Center Column Hooks
5. Install bottom decorative hub (16) onto the base of the fixture body. Secure with
bottom nipple (17) then tighten with hex nut (18).
6. Complete bottom assembly by tightening decorative finial (19) onto bottom nipple (17).
13. Center
Column
14. Fixture Decorative
Loop (x4)
BULB INSTALLATION:
1. Install B10 Bulb 60W max. (not included).
B10 Bulb 60W
max. (not included)
(x12)
15. Decorative Loop
Screw (x8)
Socket
Fixture Body
16. Decorative Bottom Hub
17. Bottom Nipple
18. Hex Nut
19. Decorative Finial
Page 4
Page 5