TroposAir 88701 Instructions / Assembly

Owner’s Manual
Voyage
4VO40
This instruction contains 5 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation and Hanging system installation
Page 4: Wire connection and Canopy installation
Page 5: B lade and Pull Chain Knob installation
UL
Net weight
9.0
KGS.
19.8
LBS.
R
Toll Free: 1-855-676-7247
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL/ETL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation. The bearings are adequately charged with grease,
so that under normal conditions, further lubrication should not be necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11]. This fan is suitable for slope ceiling.
12]. This fan is reversible.
13]. This fan is light kit adaptable.
14]. This fan is remote adaptable.
15]. This fan is suitable for damp location use.
P1
Unpack and inspect fan carefully to be certain
all contents are included.
Mounting
Bracket
Hardware Bag
For Mounting Bracket:
Flat Washer x2
Spring Washer x2
Downrod
Assembly
Machine Screw x2 Wood Screw x2
For Wire Connection:
Wire Nut x 3
For Blade Installation:
Canopy
Blade Screw x 9
(one spare screw included)
Spring Hook x 9 (one spare hook included)
Yoke cover
For Fan :
Pull chain knob x1
Wires
Fan Assembly
Blade Frame (4)
Canvas Blades(4)
P2
WARNING: blades should be at least 7 feet from floor
Note 1:
Note 2:
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable
for fan support.
Outlet box must support 35 lbs min.
OFF OFF OFF
1. HANGING SYSTEM INSTALLATION
1A. Installing mounting bracket to ceiling outlet box
Install mounting bracket to outlet box in ceiling by using screws included with the outlet box and
washers from the hardware bag.
Outlet Box
Mounting
Bracket
1B. Installing Downrod and Yoke
1 Remove cross pin and cotter pin from downrod.
2 Insert downrod through canopy and yoke cover, and feed motor lead wires through downrod.
3 Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
4 Insert the cross pin through yoke & downrod and secure with cotter pin.
5 Tighten both downrod jam screws to further secure downrod.
6 Pull down the yoke cover to cover yoke.
2 Wires
Downrod
Assembly
Downrod
1 Cross Pin
1 Cotter Pin
Canopy
4 Cotter Pin
5
3
Downrod Jam
Screw(2)
( Loosen ing)
Downrod Jam
Screw(2)
(Tightening)
Yoke
Yoke cover
Yoke cover
6
4 Cross Pin
Yoke
1C. Hanging the fan
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Lift fan assembly onto mounting bracket.
Mounting
Bracket
Ridge
Fan Assembly
Ball Groove
P3
Mounting
Bracket
2. WIRE CONNECTION
Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts or terminal block.
Note : Wires from house may vary in color and may not include ground wire ( green ).
*White wire from house to white wire from fan
*Black wire from house to black wire and blue wire from fan
*Ground wire from house to green wire from downrod and from mounting bracket
*Secure with twist - lock wire nuts. (Included)
* After wiring is completed, gently push wires into junction box with wire nuts pointing upward.
Outlet Box
From House
Wire Form House
From Fan
White
White
Black
(AC-N)
(MOTOR-N)
(AC-L)
(MOTOR-L)
Black
( for light kit )
Green
( from downrod )
( for ground wire )
( from mounting bracket )
Blue
Green
Green
Secure with twist - lock wire nuts.
3. CANOPY INSTALLATION
Note: Two screws are pre-installed on mounting bracket for canopy installation.
1 Push up canopy until two screws pre-screwed on mounting bracket are engaged with two key holes
on canopy.
2 Rotate canopy slightly until two pre-installed screw heads are engaged in the narrow end of key holes.
3 Tighten both screws.
1 Canopy
3 Screw (2)
2 Key Hole (2)
P4
4. BLADE INSTALLATION
4A. Attach canvas blades onto blade frames
4B. Attach blade assembly to motor
Connect spring hooks (6) from blade frame to
relative eyelets on canvas blade.
Note: Leave those two eyelets of Tip and
Bottom ends for Step 4C.
1 Remove 3 motor stoppers by removing screws.
2 Secure Blade Assembly to the motor with
2 motor screws provided from hardware bag.
Spring Hook
Spring Hook (6)
Blade Frame
Eyelet
Ca
nva
sB
Blade Assembly
lad
1
e
Motor
Stoppers (3)
Bottom end
2Motor Screws
Tip end
4C. Hook up TIP end and BOTTOM end & Pull Chain Knob installation
1 TIP end : Connect Hole from tip end of blade frame to tip end eyelet of canvas with spring hook
provided from hardware bag.
2 BOTTOM end : Connect bottom end eyelet of canvas to the post hole of next blade frame
with spring hook provided from hardware bag.
3 Connect Pull Chain Knob provided from hardware bag to the pull chain from switch housing.
Canvas Blade
Eyelet
1
Spring Hook
Canvas Blade
Switch Housing
2
Post Hole
of NEXT Blade Frame
3 Pull Chain Knob
Bottom end
Eyelet
Important! Spring hook must connect the Post Hole
of NEXT blade frame, or the Canvas blade will not be flat.
5. Turn on the power at breaker box - your fan is ready for operation.
P5