TroposAir 88550 Instructions / Assembly

Owner’s Manual
Tristar
3JUD18-3M
This instruction contains 6 pages:
Page 1: Foreword
Page 2: Unpack and inspect parts contained
Page 3: Notes before installation and Hanging system installation
Page 4: Wire connection
Page 5: Canopy / Blade installation
Page 6: Light kit installation and Remote & Setting
Net weight
17.0 KGS.
3110124
37.4 LBS.
Toll Free: 1-855-676-7247
WARNING : Read and follow these instructions carefully and be mindful of all warnings shown throughout.
READ AND SAVE THESE INSTRUCTIONS
WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY
TO PERSONS, PLEASE OBSERVE THE FOLLOWING :
1]. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL/ETL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan can be made to work immediately after installation. The bearings are adequately charged with grease,
so that under normal conditions, further lubrication should not be necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11]. This fan is suitable for slope ceiling.
12]. This fan is controlled by remote.
13]. This fan is suitable for indoor use.
P1
Unpack and inspect fan carefully to be certain
all contents are included.
Mounting
Bracket
Hardware Bag
For Mounting Bracket:
Flat Washer x3
Spring Washer x3
Machine Screw x2 Wood Screw x3
Downrod
Assembly
For Wire Connection:
Wire Nut x 3
For Blade Installation:
Nut x 3
Canopy
For Blade Balance :
Balancing slide x 1
Weight block (3G x 3)
3G
M
3G
M
3G
Yoke Cover
Wires & Safety Cable
Fan Assembly
Blade Assembly (3)
CFL Bulb (13W) x 2
Remote *Battery Included
Glass
Hardware Bag
Wood Screw x2
Wire Nut x6
Bottom plate
P2
M
WARNING: blades should be at least 7 feet from floor
Note 1:
Note 2:
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable for fan support.
Outlet box must support 35 lbs min.
OFF OFF OFF
1. HANGING SYSTEM INSTALLATION
1A. Installing mounting bracket to ceiling outlet box
Install mounting bracket to outlet box in ceiling by using screws
included with the outlet box and washers from the hardware bag.
Outlet Box
Mounting
Bracket
1B. Installing Downrod and Yoke
1 Remove cross pin and cotter pin from downrod.
2 Insert downrod through canopy and yoke cover, and feed motor lead wires & safety cable through downrod.
3 Loosen 2 downrod jam screws at yoke. Insert downrod assembly into yoke.
4 Insert the cross pin through yoke & downrod and secure with cotter pin.
5 Tighten both downrod jam screws to further secure downrod.
6 Pull down the yoke cover to cover yoke.
Safety cable
2 Wires
1 Cross Pin
1 Cotter Pin
Canopy
Downrod
Assembly
Downrod
3
Downrod Jam
Screw(2)
( Loosen ing)
4 Cotter Pin
Yoke
5
Yoke cover
6
4 Cross Pin
Downrod Jam
Screw(2)
(Tightening)
Yoke cover
1C. Hanging the fan
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Lift fan assembly onto mounting bracket.
Mounting
Bracket
Ridge
Ball Groove
Fan Assembly
P3
Mounting
Bracket
2. WIRE CONNECTION
2A. Attaching safety cable to ceiling joist
Use wood screw, spring washer, and flat washer from hardware bag. Pass wood screw through closed loop of safety cable.
Secure wood screw to ceiling joist through any available slot on mounting bracket. Make sure safety cable has been
tightened securely. CAUTION: THE WOOD SCREW AND ITS SUPPORT MUST BE ABLE TO FULLY SUPPORT
THE WEIGHT OF AT LEAST 100 LBS.
Safety cable
Flat Washer
Outlet
Box
Spring Washer
Wood Screw
Safety cable
Mounting
Bracket
2B. Setting code switches for transmitter
Remote controls are tuned to operate together using 4 switches for 16 possible code combinations.
1.Setting the code on the TRANSMITTER
1 Remove battery cover.
2 Slide code switch randomly using a small screwdriver or ball point pen to slide each switch firmly up or down.
3 Slide code switch for light ON/OFF (marked as X), or DIMMING (marked as D) function.
Important! This fan includes 2 CFL bulbs, so the code switch should be at X position (ON/OFF).
You may switch code at D position (DIMMING) once incandescent bulbs are installed.
4 Install 9V DC battery.(Included)
5 Install battery cover on transmitter.
2
Transmitter
Code Switches
O
N
D
1
2
3
4
X
3
D: for light dimming
(for incandescent bulbs )
X: for light ON/OFF
(for CFL bulbs)
15
4
! Warning! CFL bulbs are not applicable to the remote with dimming function.
2C. Making electrical wire connection
Follow diagram below and make sure that all exposed wires are secured inside wire nuts.
Note: Wires from house may vary in color and may not include ground wire (green).
After wiring is completed, collect wires neatly inside hanging base.
From House
White
From Remote
White
White
Black
Black
(AC-N)
Black
(AC-L)
From Fan
(Motor-N)
(Motor-L)
White
Black
Blue
Blue
( for light kit )
Green
( from downrod )
( for ground wire )
Green
Green
Secure with twist - lock wire nuts.
( from mounting bracket )
P4
2D. Insert receiver into mounting bracket
NOTE: Do not sq u eeze all the wires while inserting the receiver into the mounting bracket.
Receiver
Mounting
Bracket
3. CANOPY INSTALLATION
Note: Two screws are pre-installed on mounting
bracket for canopy installation.
1 Push up canopy until two screws pre-screwed on mounting bracket are engaged with two key holes on canopy.
2 Rotate canopy slightly until two pre-installed screw heads are engaged in the narrow end of key holes.
3 Tighten both screws.
1 Canopy
3 Screw (2)
2 Key Hole (2)
4. BLADE INSTALLATION
1 Attach blade assembly to spindle.
2 Thread the nut to counter-clockwise to spindle until fully tightened.
1
2
Blade assembly
Nut
Nut
P5
5. LIGHT KIT INSTALLATION
For use with light kit:
5A. Install the bulbs (included) to the medium sockets properly.
5B. Attach the glass shade by screwing it onto the light kit pan clockwise.
Groove
Ribs
Glass Shade
Lamp Holder
For non-light use:
5C. Attach the bottom plate by screwing it clockwise onto the light kit pan.
Bottom plate
Turn on power at breaker box for remote setting.
6. REMOTE & SETTING
SETTING for light operation before starting fan.
Pressing the button “OFF” for 3~5 seconds till the LIGHT BLINKS , which means this remote control
has done the setting. Now the remote is ready for operation.
2
D: for light dimming
(for incandescent bulbs)
O
N
LOW:Fan low speed
HI:Fan high speed
HI
D
1
2
LO W
O FF
OFF: For SETTING / Fan speed
: Button for ON/OFF Light
3
MED:Fan middle speed
MED
4
X
X: for light ON/OFF
(for CFL bulbs)
Note: You may switch Light switch code at D position
(DIMMING) when you change to incandescent bulbs
for Down light. To use dimming, press and hold light
button(s).
P6