Hampton Bay 21392-016 Installation Guide

TROUBLESHOOTING:
Possible Cause
Bulb will not light.
Fuse blows or circuit
breaker trips when
light is turned on.
Corrective Action
1. Bulb is burned out.
1. Replace light bulb.
2. Power is off.
2. Make sure power supply
is on.
3. Faulty wire connection.
3. Check wiring.
Crossed wires or power
wire is grounding out.
Check wire connections.
INSTRUCTION MANUAL
Interior Decorative Lighting
4 Light Island Pendant
Sadie
Home Depot SKU (529-976) UPC (773546217101)
Brushed Nickel Finish
PRODUCT MAINTENANCE:
1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use
clean water, never a solvent) to wipe the shade and surface of the fixture.
2. To clean the inside of the fixture, first disconnect power to the fixture by turning
off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or
slightly dampened clean cloth (use clean water, never a solvent) to wipe the inside
shade and interior surface of the fixture.
3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry
soft cloth to dust or wipe carefully.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship
for a period of five (5) years from date of purchase. This warranty applies only to the original consumer
purchaser and only to products used in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the
manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident,
modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is
found to have been improperly installed, set-up, or used in any way not in accordance with the instructions
supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident,
misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to faulty material
or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface
and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and
specially disclaims any warranty, whether express or implied, of fitness for a particular purpose, other
than the warranty contained herein. The manufacturer specifically disclaims any liability and shall
not be liable for any consequential or incidental loss or damage, including but not limited to any labor
/ expense costs involved in the replacement or repair of said product.
Page 8
Page 1
Thank you for purchasing this Hampton Bay interior decorative lighting. This product
has been manufactured with the highest standards of safety and quality.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION
(not included):
FEATURES:
Shimmering elegance and sparkle to your decor, the jewel-like crystal accents of this
fixture will be reflected by the light coming from within. Royal black fabric shades
help complete and accentuate this fixture.
Safety goggles
Wire Strippers
Wire Cutters
Flathead
Screwdriver
Phillips
Screwdriver
Electrical Tape
B10 Bulb 60W (x4)
Ladder
Standard: 12" rod lengths to make desired height.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at
1-877-527-0313 or visit www.homedepot.com. Please reference your SKU# (529-976)
or UPC# (773546217101).
ADDITIONAL PARTS (included) (Parts are not to scale):
CAUTION:
1. Before starting installation of this fixture or removal of a previous fixture, disconnect
the power by turning off the circuit breaker or by removing the fuse at the fuse box.
2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL
QUESTIONS.
4. Canopy
5. Ball Nut
10. Lower Hex Nut
(x2)
11. Lock Washer
12. Metal Washer 13. Retaining Screw
14. Decorative Cap
15. Glass Shade
17. Candle Sleeve
with Glass Holder
22. 12" Bottom Rod
3. If you have any non-electrical questions about this fixture, please contact our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com. Please
reference your SKU# (529-976) or UPC# (773546217101).
4. Keep your receipt and these Instructions for Proof of Purchase.
Page 2
20. Bottom Finial
Page 3
ASSEMBLY INSTRUCTIONS:
1. Carefully unpack the fixture; lay out all parts on clean surface.
ASSEMBLY:
10. Lower Hex Nut
11. Lock Washer
2. Screw-in tightly and attach the 12" rod (part of main fixture body), followed by the
12" bottom rod (22) to the fixture nipple (21).
12. Metal Washer
4. Canopy
3. Tighten the retaining screw (13) to hold the end-piece (part of fixture body) to the
top-most 12" rod (part of fixture body). (Adjust the desired height by removing
the rods).
13. Retaining Screws
4. Draw the wires (including the grounding wire) through the canopy (4) and attach
the canopy (4) to the end-piece with the metal washer (12), lock washer (11) and
tighten with lower hex nut (10).
12" Rod (Part of Fixture Body)
5. Attach bottom finial (20) to each Candelabra Bobeche (19).
6. Place candle sleeve with glass holder (17) over socket (18).
14. Decorative
Cap
GLASS AND BULB INSTALLATION:
1. Install 60W max B10 chandelier bulbs (not included).
15. Glass Shade
2. Place glass shade (15) onto candle sleeve with glass holder (17).
16. 60W B10 Bulb
(not included)
3. Tighten and secure glass shade (15) with decorative cap (14).
22. 12" Bottom
Rod
17. Candle Sleeve
with Glass
Holder
18. Socket
19. Candelabra
Bobeche
Fixture
Main Body
21. Fixture
Nipple
20. Bottom Finial
Page 4
Page 5
PARTS INCLUDED FOR INSTALLATION
(parts are not to scale):
INSTALLATION:
Black Wire
1. Junction Box
(not included)
White Wire
2. Wire Nut
3. Cross Bar
4. Canopy
5. Ball Nut
2. Wire Nuts
6. Hex Nut
8. Ground Screw
9. Outlet Box
Screws
23. Nipple
ASSEMBLY INSTRUCTIONS:
1. Screw the cross bar (3) to the junction box (1) with the outlet box screws (9). Hand
tighten until snug.
Ground Wire
3. Cross Bar
8. Ground Screw
6. Hex Nut
9. Outlet Box
Screws
23. Nipple
4. Canopy
5. Ball Nut
2. Pliers are required for the next step. Thread one hex nut (6) onto the top end of the
nipple (23).
3. Thread the nipple (23) into the center lock hole of the cross bar (3).
4. Using pliers, thread the hex nut (6) against the cross bar (3) and hand-tighten
until snug.
Figure #1
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
5. Use wire nuts (2) (included) to connect the wires. Connect the house ground wire
from the fixture ground wire. (Refer to Figure #1)
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM HOUSE
FROM FIXTURE
GROUND WIRE
GROUND WIRE
FROM HOUSE
FROM FIXTURE
6. Connect the house white (or ribbed) wire to the fixture supply wire (black or
smooth side). (Refer to Figure #1)
7. Connect the house black (or red) wire to the fixture supply wire (black or smooth side).
(Refer to Figure #1)
8. Wrap each connection with approved electrical tape and carefully stuff all of the
connected wires into the outlet box. (Refer to Figure #1)
9. Thread another hex nut (6) onto the bottom end of the nipple (23) and adjust to
proper location for canopy (4) and ball nut (5).
10. Pass the canopy (4) over the end of the nipple (23) and secure with the ball nut (5).
Hand-tighten until snug.
Page 6
Page 7