Kenroy Home 91558CH installation Guide

 Monet: 91558
ASSEMBLY INSTRUCTIONS
| | CANOPY
SWIVEL READ AND SAVE THESE INSTRUCTIONS
_ ap #-—FINIAL (2 PCS) TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, ADJUSTABLE
WRENCH, WIRE CUTTERS.
вена PF UNPACK THE FIXTURE
(REPLACEMENT PART) TO PROTECT THE FINISH, PLACE ALL PARTS ON A
SOFT SURFACE AND HANDLE THESE PARTS WITH
GLOVES. YOU SHOULD HAVE RECEIVED THE
FOLLOWING: CANOPY, (4) 12” AND (2) 6” EXTENSION
TUBES, FIXTURE BODY, GLASS SHADE AND SOCKET
| RING. TO PROTECT THE FINISH, PLACE ALL PARTS ON
A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
> (2) GLOVES, (4) 8-32 x 1-1/4” SCREWS, (2)
y NUTS, MOUNTING PLATE, GREEN GROUND SCREW, (3)
TENSION WIRE CONNECTORS AND (2) FINIALS.
TUBE
FIXTURE ASSEMBLY
1. FEED WIRE UP THROUGH TUBING AND WORKING
, UPWARDS TOWARD CANOPY AS SHOWN.
] 2. SCREW EXTENSION TUBE TO TOP OF FIXTURE
i BODY. (USE ANY SINGLE LENGTH OF EXTENSION
EXTENSION TUBE TUBE OR CONNECT TUBE SECTIONS TOGETHER TO
91557ROD6 OBTAIN DESIRED LENGTH.)
(REPLACEMENT PART)
| 3. SCREW EXTENSION TUBE TO SWIVEL ON CANOPY.
Т GLASS SHADE:
I 91558GS **STOP** COMPLETE INSTALLATION INSTRUCTIONS
@ = (REPLACEMENT PART) ON NEXT PAGE BEFORE PROCEEDING.
FINAL ASSEMBLY
1. PLACE A GLASS SHADE OVER SOCKET AND
\ SECURE WITH SOCKET RING.
— GLASS SHADE
ES 2. INSTALL A 150 WATT MAX. MEDIUM BASE TYPE "A"
BULB (NOT INCLUDED) INTO SOCKET.
= SOCKET RING 3. RESTORE POWER. YOUR FIXTURE IS NOW READY
FOR USE.
CE SOCKET
! О AVAILABLE PARTS ARE:
91558С5 (GLASS SHADE)
91557ROD12 (EXTENSION TUBE)
91557ROD6 (EXTENSION TUBE)
eL
3/08 91558 ASSEMBLY INSTRUCTIONS
— OUTLET BOX
X WHITE SUPPLY WIRE
| WIRE CONNECTORS,
| (3 PCS)
SUPPLY GROUND WIRE
BLACK SUPPLY WIRE
CEILING
WHITE OR RIBBED
BLACK OR SMOOTH |
FIXTURE WIRE | FIXTURE WIRE
8-32 SCREWS, FIXTURE GROUND WIRE
SUPPLIED WITH BOX Co - MOUNTING PLATE
B—32 x 1-1/2" SCREW —
GREEN GROUND SCREW
CANOPY -| |
} SWIVEL
FINIAL (2 PCS) |] | []
EXTENSION
TUBE -
— IN
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRST TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES.
** IF YOU ARE NOT FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
*** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST (SEE PREVIOUS).
1. SCREW (2) 8-32 x 1—1/4" SCREWS INTO THE MOUNTING PLATE MAKING SURE THAT THEY LINE UP WITH
THE HOLES IN THE CANOPY. ATTACH THE MOUNTING PLATE TO THE CEILING OUTLET BOX USING THE TWO
SCREWS PROVIDED WITH THE OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT,
USE THE (2) 8-32 x 1-1/4" SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE).
2. CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING
THE TWIST—ON WIRE CONNECTORS PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK
SUPPLY WIRE IN THE SAME MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW
ON THE MOUNTING PLATE THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE
OUTLET BOX USING THE TWIST—ON WIRE CONNECTOR PROVIDED.
3. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE.
4. RAISE THE FIXTURE TO THE CEILING AND SECURE IN PLACE WITH (2) FINIALS.
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS. U
eL
3/08 91558 INSTALLATION