advertisement
SINGLE COLOUR LED TAPE
Installation Guide
Stock code
156.705UK
156.706UK
156.708UK
156.711UK
156.714UK
156.717UK
156.718UK
156.755UK
156.756UK
156.758UK
156.761UK
156.764UK
156.767UK
156.768UK
24Vdc
24Vdc
24Vdc
Common Specifications
Number of LEDs
Beam angle
Cut intervals
Reel length
LED type
LED spacing
IP rating
Voltage Colour
12Vdc Red
12Vdc
12Vdc
Pink
Green
12Vdc
12Vdc
12Vdc
12Vdc
Blue
Yellow
White (6500K)
Warm white (2700K)
24Vdc
24Vdc
24Vdc
24Vdc
Red
Pink
Green
Blue
Yellow
White (6500K)
Warm white (2700K)
60/m
140°
5cm
5m
Epistar™ SMD3528
16mm
IP65
Power consumption / metre
Cross-section
Weight
4.8W
10.5 x 2.55mm
210g
Luminous flux
(Lumens per metre)
60lm/m
120lm/m
130lm/m
30lm/m
45lm/m
180lm/m
180lm/m
60lm/m
120lm/m
130lm/m
30lm/m
45lm/m
180lm/m
180lm/m
Light intensity per LED
(millicandelas)
600mcd
1000mcd
1200mcd
500mcd
600mcd
2400mcd
2400mcd
600mcd
1000mcd
1200mcd
500mcd
600mcd
2400mcd
2400mcd
Caution: Please read this guide carefully before installing Fluxia LED tape
Damage caused by incorrect application is not covered by the warranty
Fluxia single colour LED tape is supplied on 5m reels in either 12Vdc or 24Vdc voltages.
Installation should be carried out by competent electrical installers, observing the relevant electrical safety procedures.
Fluxia single colour LED tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size. These cut points will be at 5cm intervals for 12V tape and 10cm intervals for 24V tape. In order to re-connect to another length of tape after cutting, strip away the epoxy coating at the solder points and solder a wire from “+” to “+” and a wire from
“-” to “-” as shown below. Some accessories are supplied with the tape reel for this purpose. In order to retain weatherproofing, it is advised to seal the cuts and joints with silicone glue.
Each 5m reel of single colour LED tape is fitted with a 2.1mm DC jack socket for power input for easy connection to a power supply. This connector may be removed and stripped for bare wire connection if a 2.1mm jack is not fitted to the power supply.
If the power supply has enough capacity to power more than one reel, another reel can be connected to the end of the first reel via the 2.1mm DC jack plug.
For 12V single colour LED tape, it is recommended to link no more than 15m of tape in sequence. For 24V versions, up to
30m can be linked in this way. Using a separate wire to loop “+” and “-” back to the power supply will help to avoid dimming at the far end through voltage drop. To connect beyond these lengths, a parallel wire must be run from the power supply to the further reels of tape.
2A
1A
4A
2A
6A
3A
8A
4A
10A
5A
12A
6A
14A
7A
16A
8A
It is imperative that the power supply should have higher than the rated capacity in Amps (A) for the current required to power the length(s) of LED tape installed. Please see the table below for reference.
Tape length 5m 10m 15m 20m 25m 30m 35m 40m
Current for 12V tape
Current for 24V tape
Please visit www.avsl.com
to select from our range of 12Vdc and 24Vdc power supplies that are suitable for powering
Fluxia LED tapes.
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright © 2014. AVSL Group Ltd.
Single Colour LED Tape Installation Guide
advertisement
Related manuals
advertisement