Minka Lavery 2242-267C Installation Guide

INSTALLATION INSTRUCTIONS
Item#2242 (New. 06/11/2013)
W ARNING !
READ AND SAVE THESE INSTRUCTIONS
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
Fig. 1
PREPARATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the
mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
A
B
C
D
L2
ASSEMBLING THE FIXTURE (Fig. 2)
3. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the nipple (M) of the fixture body
(H). Pass the wires carefully through each rod as you
assemble. Then attach loop (L1) by screwing in to rod
(F1). Note: remove the nipple if installing with one 6”
rod only.
4. Attach the quick link (G) to loop (L1) and loop (L2) on
the canopy (D). Carefully feed the wire over loop (L1),
quick link (G) and loop (L2).
5. Thread screws (A) into the pre-drilled holes in the
circular strap (B) spaced the same distance apart as
the holes in the canopy (D).
6. Attach the circular strap (B) to the junction box using
mounting screws (C) (Size: #8-32N*L0.5”). The side
of the circular strap marked “GND” must face out.
E
G
L1
F1
F2
F3
H
CONNECTING THE WIRES (Fig. 3)
Set# A-020
-Circular Strap
-Ground screw
-Mounting Screw*2
Rod# W30-1-77*1(F1)
W30-1-77*2(F2)
W30-H-77*1(F3)
Or: # W30-1-267C*1(F1)
W30-1-267C*2(F2)
W30-H-267C*1(F3)
M
I
7. At this point, connect the electrical wires as shown in
figure 3, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or
bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly
to the circular strap using the green screw provided.
8. Tuck the wire connectors neatly into the ceiling
junction box and raise the canopy all the way to the
ceiling.
J
K
Socket Ring # SKT-RING-26
COMPLETING THE INSTALLATION (Fig. 1)
9. Thread screws (A) into canopy (D), and secure with
knurled knobs (E).
10. Place the glass shade (I) over the socket on the
fixture body (H), and fasten with the socket ring (J).
11. Install the light bulb(s) (K) (not included) in
accordance with the fixture’s specifications. (DO NOT
EXCEED THE MAXIMUM WATTAGE RATING!) (NE
PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!).
Fig. 3
FIXTURE
WIRES
Black or
Smooth
Your installation is now complete. Return power to the
junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Page: 1/2
LA-2253E
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Fig.2
A
B
C
L2
D
E
G
F1
L1
a. Hardware Bag:
A. Screw*2
B. Circular Strap*1
D. Canopy *1
b. Hardware Bag:
F1. ROD 12"*1
F2.Mounting
ROD 12"*2
C.
Screw*2
F3. ROD 6"*1
F2
F3
F1
E. Knurled Knob*2
B
D
L. Loop*2
Page: 2/2
G. Quick Link*1
LA-2253E
C
G
A
E
L