Minka Lavery 4415-281 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#4415-281 (New. 01/15/2015)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig. 1)
Fig. 1
Set# A-020
-Circular Strap
-Ground screw
-Mounting Screw*2
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including the
mounting hardware.
2. Carefully remove the fixture from the carton and
check that all parts are included as shown in the
illustration.
3. Connect the steel cable and fixture body together by
threading Screws (J) on end of steel cables into
Coupling (K) on the fixture body (P).
A
B
C
H2
ASSEMBLING THE FIXTURE WITH CHAIN LOOP (Fig. 2)
4. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the nipple (I) of the fixture body (J).
Then attach loop (H1) by screwing in to rod (F1).
Note: remove the nipple if installing with one 6” rod
only.
5. Attach the quick link (G) connect to loop (H1) and
loop (H2) on the canopy (D), carefully feed the wire
over loop (H1), quick link (G) and loop (H2).
6. Thread screws (A) into the pre-drilled holes in the
circular strap (B) spaced the same distance apart as
the holes in the canopy (D).
7. Attach the circular strap (B) to the Junction box using
mounting screws (C) (Size: #8-32N*L0.5”). The side
of the circular strap marked “GND” must face out.
D
E
G
H1
F1
Rod# W30-1-281*1(F1)
W30-1-281*2(F2)
W30-H-281*1(F3)
F2
F3
O
K
N
L
J
M
CONNECTING THE WIRES (Fig. 3)
8. At this point, connect the electrical wires as shown in
figure 3, making sure that all wire connectors are
secured. If your outlet has a ground wire (green or
bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly
to the circular strap using the green screw provided.
9. Tuck the wire connectors neatly into the ceiling
Junction Box and then raise the canopy all the way to
the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
10. Thread screws (A) into canopy (D), and secure with
knurled knobs (E).
11. Place the glass shade (M) followed by metal ring (L)
over the socket, fasten with screw shell (N) by using
the tool (O).
12. Install the A19 1*100W (MED BASE) light bulb (not
included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA
PUISSANCE NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the
junction box and test the fixture.
Page:Illustration
1/2
Note:
(Fig. 1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
P
Socket ring # SKT-RING-26
E26 Socket Spanner: WRH-1-51
Fig. 3
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
LA-2438E
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Fig.2
A
B
C
H2
D
E
G
H1
F1
a. Hardware Bag:
A. Screw*2
B. Circular Strap*1
D. Canopy *1
C. Mounting Screw*2
E. Knurled Knob*2
H. Loop*2
G. Quick Link*1
b. Hardware Bag:
F1. ROD 12"*1
F2. ROD 12"*2
F3. ROD 6"*1
Page: 2/2
B
D
C
F2
F3
F1
LA-2438E
A
E
G
H