Minka Lavery 4404-581 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#4404-581
READ AND SAVE THESE INSTRUCTIONS
WARNING!
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the fixture from the carton and check that
all parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old fixture
including the mounting hardware.
3. The Crossbar (B) contains several pairs of threaded holes,
find the pair of holes that match the holes spacing in your
Junction box Attach the Fixture Crossbar (B) to the Junction
Box using the two Mounting srews (C size: 8/32*25mm).
Tighten the screws (C) securely with screwdriver.
4. Thread one end of the Nipple (R) attached into ceiling
loop(D),the other end attached into Crossbar (B) and Tighten
the Washer and Hex Nut until tightening to the Crossbar (B)
5. Attached below fixture body(Q) to top fixture body(I) by
thread Fixture body(Q) to the bottom of the Tube(J).
6. Place the Fixture body(I) onto the Metal frame(L) and tighten
the fixture(I) to the tube(J)and secure them together by
Screw(K).
7. Screw the loop(G) on to the nipple(H) tighten.After complete
to this step ,please keep you fixture wire smooth.
8. Use one chain connector(E) to attach one end of the chain to
the Top loop (G) and close the chain connector.
9. At this step,you may determine how long of the chain you
would like to use.By measuring determine correct number of
links needed for proper hanging height. Use a pair of pliers to
open one link of the Chain (F) then remove the excess Chain
(F) and discard it.
10. Slip Canopy loop collar (T) and canopy(S) over the chain.
Use the other chain connector(E) and attach the other end of the
chain to the ceiling loop (D) and close the chain connector.
11.fixture wire through the chain (F) canopy loop(D) Canopy
loop collar (T) and nipple(R) and into the outlet box.This step
please refer below Fig 2 wire connecting.
12.Raise Canopy (S) over the nipple(R) to the ceiling and secure
in place by tightening the Canopy loop collar T
onto the
Canopy Loop (D)..
13.Hanging the crystal(P) and crystal(O) under the socket and
arm.
CONNECTING THE WIRES (Fig. 2)
14.At this point, connect the electrical wire as shown in (Fig.2),
making sure that all wire connectors are secured. If your outlet
has a ground wire (green or bare copper), connect the fixtures
Ground Wire to it. Otherwise, connect the fixture Ground Wire
directly to the circular strap using the Green Screw provided.
Fig.
Crossbar#A-016
- Crossbar
- Ground Screw
- Mounting Screw*2
Chain# HCH2072-581
()
FINISH THE INSTALLATION (Fig. 1)
15.Install light bulb (not included) in accordance with the fixture’s
specifications. (DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!!) (NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
Your installation is now complete. Return power to the junction
box and test the fixture. Note: Illustration (Fig.1) on this
manual is for installation purposes only. It may or may not
be identical to the fixture purchased.
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
Notice: It is important to use proper
chain pliers (not included)
To OPEN and CLOSE the chain
included with this fixture. Do not open
them with other tools that may twist or
stress the chain links. It is important to
use proper chain pliers like the ones
shown in the diagram.
4404-581
HOUSE
WIRES
Green
(Ground)