Minka Lavery 4971-269 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#4971-269 (Rev. 03/13/2014)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
Fig.1
1. Shut off the power at the circuit breaker. If necessary, remove
the old fixture from the ceiling including the mounting hardware. Set# A-016
2. Carefully remove the new fixture from the carton and check that - Crossbar
all parts are included as shown in the illustration.
- Ground Screw
3. Screw the fixture loop into the nipple onto the fixture body (A) - Mounting Screw*2
until snug.
4. Place the cover (B), glass shade (C) and metal ring (D) over the
socket of the fixture body (A). Then secure with socket ring (E)
using the spanner (F) provided.
HANGING THE FIXTURE (Fig. 3)
5. Thread the nipple into the ceiling loop until snug.
6. Thread the other end of the nipple into the crossbar until snug.
Note: The length of the nipple into the crossbar may be
adjusted if necessary.
7. Place the lock washer and hex nut over the end of nipple
protruding through crossbar. Then thread the hex nut onto the
nipple until snug.
8. Take this crossbar assembly and mount it to the ceiling outlet
box using the mounting screws (Size: #8-32N*L0.5”). The side Spanner # WRH-T1-51
of the crossbar marked “GND” must face out.
Socket Ring # SKT-RING-26
9. Use proper chain pliers to open one end link of the chain and
connect to the fixture loop. Then close the link.
10. By measuring, determine the desired hanging height and use Fig. 2
the chain pliers to remove and discard the excess chain.
FIXTURE
FIXTURE
WIRES
WIRES
11. Carefully lace the fixture wires through the chain.
Black or
White or
Smooth
Ribbed
12. Slip the lock collar and canopy over the chain and allow them
to rest on the fixture body.
13. Open the other end link of the chain and attach it to ceiling
loop and close the link.
HOUSE
WIRES
Black
14. Feed the fixture wires through the loop and nipple assembly
(Hot)
and pull tight.
CONNECTING THE WIRES (See Fig.2)
15. At this point, connect the electrical wires as shown in Fig. 2, Fig.3
Outlet Box
making sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
Hex Nut
ground wire directly to the crossbar using the green screw
Crossbar
provided.
16. Tuck the wire connections neatly into the ceiling outlet box and
raise the canopy to the ceiling. Thread the lock collar to the
ceiling loop to secure the canopy against the ceiling.
COMPLETING THE INSTALLATION (Fig. 1)
17. Install the light bulb(s) (not included) in accordance with the
fixture’s specification. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!) (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!)
Your installation is now complete. Return power to the outlet box
Chain# HCH2072-269
and test the fixture.
LOOP
A
B
C
D
E
F
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Lock Washer
Mounting Screw
Nipple
Ceiling Loop
Chain
Canopy
Lock Collar
Wire
Loop
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do not
open them with other tools that may twist or stress the chain
links. It is important to use proper chain pliers like the ones
shown in the diagram.
LA-2401E