Minka Lavery 4943.570 Instructions / Assembly

INSTALLATION INSTRUCTIONS
Item#4943 (New. 05/08/2013)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig. 1 and Fig. 4)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture including mounting hardware.
2. Carefully remove the new fixture from the carton and check that
all parts are included as shown in the illustration.
3. Adjust the arms to proper position. (Fig.4)
4. Attach fixture loop (A) by screwing to nipple (F).
HANGING THE FIXTURE (Fig. 2)
5. Thread the nipple into the ceiling loop until snug.
6. Thread the other end of the nipple with the ceiling loop attached
into the crossbar until snug.
7. Place lock washer over the end of nipple protruding through
crossbar and thread hex nut onto nipple until snug.
8. Take this crossbar assembly and mount to the ceiling junction
box with the mounting screws (Size: #8-32N*L0.5”) provided.
Secure mounting screws with a screwdriver. The side of
crossbar marked “GND” must face out.
9. By measuring determine the correct number of links needed for
the desired hanging height.
10. Attach the chain to the fixture loop (A) using a quick link. Quick
link must be completely threaded closed when installed. Use a
pair of chain pliers to open one end link of the chain and discard
un-wanted chain. Slip the lock collar and canopy over the chain.
11. Use the chain pliers to open the other end link of the chain and
lift the fixture to attach to the ceiling loop, close the chain link.
12. Lace the fixture wires through the chain and through the ceiling
loop and nipple and pull until tight.
CONNECTING THE WIRE (Fig. 3)
13. At this point, connect the electrical wire as shown in figure 3,
making sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the crossbar using the Green Screw
provided.
14. Tuck these wire connections neatly into the ceiling junction box
and raise the canopy all the way to the ceiling. Raise the Lock
Collar and thread onto the ceiling loop protruding through
canopy.
FINISHING THE FIXTURE (Fig.1)
15. Place the tube (C) over the socket (E).
16. Install the light bulb(s) (not included) in accordance with the
fixture’s specifications. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING!). (NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!) Clip the fabric shade(s) (D) onto the
Bulb(s).
Your installation is now complete. Return power to the junction
box and test the fixture.
Fig. 1
Set# A-012
-Crossbar
-Ground screw
-Mounting Screw*2
D
A
F
C
E
B
Fig. 2
Junction Box (Ceiling)
Hex Nut
Lock Washer
Nipple
Cross Bar
Mounting
Screws
Canopy
Lock Collar
Ceiling loop
Chain (End link)
Quick Link
Fixture Loop
Chain # HCH7072
Fig. 3
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
Fig. 4
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased.
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
LA-2289E
HOUSE
WIRES
Green
(Ground)