Minka Lavery 9144-407 Installation Guide

INSTALLATION INSTRUCTIONS
Model # 9144
READ AND SAVE THESE INSTRUCTIONS
WARNING!
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
Shut off the power at the fuse box or circuit breaker box and
remove old fixture from ceiling, including the old crossbar.
Carefully unpack your new fixture and lay out all the parts in a
clear area. Take care not to misplace any small parts necessary
for installation.
By measuring determine correct number of links needed for
proper hanging height. Using a pair of proper chain pliers
disconnect and discard remaining chain.
Open on the end of the chain (E), attach the Loop (L) to the
Chain (E) and close the chain (E). Slip Loop Collar (K) followed
by the Canopy over the chain. Open the other end link of the
Chain (E) and lift the fixture to attach to the ceiling loop (D),
close the chain.
Lace the fixture wires through the chain.
Thread nipple (I) into ceiling loop (D) until snug.
Thread other end of nipple (I) with loop(D) attached into single
bar (H) until snug.
Place lock washer (G) over end of nipple (I) protruding through
crossbar and thread hex nut (F) onto nipple(I) until tight.
Feed the fixture wires through the Loop (D) ,the canopy(J) and
nipple (I) and pull until taut.
At this point, connect the electrical wires as shown in Fig. 2.
Making sure that all wire connectors are secured. If your
junction box has a ground wire (green or bare copper), attach
this wire and the bare copper wire from the fixture together.
Otherwise, attach the bare copper fixture wire to the crossbar
using the green screw (B) provided.
Take this single bar assembly and mount to ceiling outlet box
(A) with outlet box screws (C). Tighten screws securely with
screwdriver.
Tuck these wire connections neatly into the ceiling outlet box
and then raise the canopy (J) all the way to the ceiling. Raise
the loop collar (K) and thread onto ceiling loop protruding
through canopy (J).
At this point, unscrew the finial (P) and the nut (O), move the
bottom holder (N) and the cage (M) with glass gently to install
the bulbs in accordance with the fixture’s specification—DO
NOT EXCEED THE MAXIMIUM WATTAGE RAITTING!
Replace the cage (M) and the bottom holder (N), secure with
the nut (O) the finial (P).
Fig. 1
A
F
G
H
I
J
K
B
C
D
E
L
M
N
O
P
Fig.2
FI XTURE
WI RES
GREEN OR
BARE
COPPER
( GROUND)
FI XTURE
WI RES
WHI TE
FI XTURE
WI RES
BLACK
HOUSE
WI RES
BLACK
( HOT)
HOUSE
WI RES
WHI TE
( NEUTRAL)
HOUSE
WI RES
GREEN OR
BARE COPPER( GROUND)
Your installation is now complete. Return power to the outlet box
and test the fixture.
“CAUTION-RISK OF FIRE CONSULT A
QUALIFIED ELECTRICIAN TO ENSURE
CORRECT BRANCH CIRCUIT CONDUCTOR”
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
U.S. Patents: D512,176; D515,237
This product is protected by United
States Federal and/or State Law,
including Patent and/or Copyright laws.