Hampton Bay EW556CH Installation Guide

INSTRUCTION
MANUAL
BATH BAR
Chrome Finish
Home Depot SKU 644-291 (UPC008938102100)
1
Thank you for purchasing this Hampton Bay interior bath bar. This product has been
manufactured with the highest standards of safety and quality.
FEATURES:
1.
2.
3.
Designed with 6 - 100 watt bulb sockets.
Compatible with any standard 120 volt incandescent dimmer switch.
Wall mountable only.
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our Customer Service Team at 1877-527-0313 or visit www.homedepot.com. Please reference SKU 644-291, UPC
008938102100.
GENERAL:
1.
Be sure to read these installation instructions and review the diagrams thoroughly
before installing this light fixture.
2. All electrical connections must be in accordance with local codes and the National
Electrical Code. If you are unfamiliar with methods of installing electrical wiring,
secure the services of a qualified licensed electrician.
3. This fixture is intended to be mounted to a 4 square x 2-1/8 deep metal octagon
outlet box. The box must be directly supported by the building structure.
4. Before starting the installation, disconnect the power by turning off the circuit
breaker or by removing the appropriate fuse at the fuse box. Turning the power off
using the light switch is not sufficient to prevent electrical shock.
5. Keep your receipt and these Instructions for Proof of Purchase.
Note: The important safeguards and instructions appearing in this manual are not meant to
cover all possible conditions and situations that may occur. It must be understood that
common sense, caution and care are factors that cannot be built into any product. These
factors must be supplied by the person(s) caring for, installing and operating the fixture. If
at any time you are uncomfortable or are unsure of what to do, please contact a qualified
licensed electrician for further assistance.
TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included):
Ladder
Safety
Goggles
Gloves
Flathead
Screwdriver
Phillips
Screwdriver
Electrical
Tape
Wire
Cutters
A19 or G25
bulb
PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):
x2 Screws
x3 Wire Connectors
x2 Tapped Screws
x 2 anchors
INSTALLATION INSTRUCTIONS:
1. Turn off the power by either turning off the breaker at the electrical panel or by
removing the fuse from the fuse box.
2. If you are replacing an existing fixture, disconnect and remove the old fixture. Expose
the supply wiring from the outlet box.
3. Remove the back mounting plate (A) from the front cover (B). Set aside for
reassembly.
4. Fasten the back mounting plate (A) to the wall using the two anchors and tapped
screws supplied. Or fasten the back mounting plate (A) to the outlet box using the two
screws supplied with the outlet box. Your fixture is supplied with a back mounting
plate with two keyhole slots for attachment to the front cover (B). It will be necessary
to mark the location of the keyholes slots on the back mounting plate surface (A) and
2
drill holes in the wall for the fasteners. The narrow end of the keyhole slot should face up.
5. Make electrical connections.
ELECTRICAL CONNECTIONS:
a.
b.
c.
d.
e.
f.
Connect the white wire(s) from the fixture to the white wire of the supply circuit.
Connect the black wire(s) from the fixture to the black wire of the supply circuit.
Connect the green colored (or bare copper) wire to the grounding conductor of the
supply circuit.
Use U.L. Listed wire connectors suitable for the size, type and number of conductors.
No loose strands or loose wires should be present.
Secure wire connectors with U.L. Listed electrical tape.
Carefully tuck connected wires back into the outlet box.
FINAL ASSEMBLY:
1. Spread the electrical splices so that the black wires are on one side of the outlet box
and the white wires are on the other side.
2. Place the front cover (B) against the back mounting plate (A). Push each socket cup
(C) onto socket firmly against cover (B).
3. Install light bulbs (D) (sold separately).
CAUTION: Refer to the re-lamping label located near the lamp holder for recommended
maximum wattage. DO NOT exceed the recommended maximum wattage.
4. Restore electricity and check the operation of your new lighting fixture.
ASSEMBLY AND INSTALLATION DIAGRAM:
CLOCKWISE
GREEN OR BARE (GROUND)
WHITE (NEUTRAL)
BLACK
(HOT)
3
TROUBLE SHOOTING:
Problem
Light Bulb will not illuminate.
Fuse blows or circuit breaker
trips when light bulb is
illuminated.
Possible Cause
1. Light bulb is burned out.
2. Power is off.
3. Faulty wire connection.
4. Faulty switch.
Crossed wires or power wire
is grounding out.
Corrective Action
1. Replace light bulb.
2. Make sure power supply is
on.
3. Check wiring.
4. Test or replace switch.
Check wire connections.
PRODUCT MAINTENANCE:
1.
To clean the fixture, first disconnect power to the fixture by turning off the circuit
breaker or by removing the fuse at the fuse box.
2. Use a dry or slightly dampened clean cloth (use clean water, never use a solvent) to
wipe the interior and exterior surfaces of the fixture.
3. Allow the fixture to dry thoroughly before power is restored.
CAUTION: Do not use chemical solvents or harsh abrasives to clean fixture as damage to
the fixture’s finish or various components may occur.
LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and
workmanship for a period of three (3) years from date of purchase. This warranty applies
only to the original consumer purchaser and only to products used in normal use and
service. If this product is found to be defective, the manufacturer’s only obligation, and
your exclusive remedy, is the repair or replacement of the product at the manufacturer’s
discretion, provided that the product has not been damaged through misuse, abuse,
accident, modifications, alterations, neglect or mishandling. This warranty shall not apply
to any product that is found to have been improperly installed, set-up, or used in any way
not in accordance with the instructions supplied with the product. This warranty shall not
apply to a failure of the product as a result of an accident, misuse, abuse, negligence,
alteration, or faulty installation, or any other failure not relating to faulty material or
workmanship. This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear. The
manufacturer does not warrant and specially disclaims any warranty, whether express or
implied, of fitness for a particular purpose, other than the warranty contained herein. The
manufacturer specifically disclaims any liability and shall not be liable for any
consequential or incidental loss or damage, including but not limited to any labor/expense
costs involved in the replacement or repair of said product.
4