the great outdoors by Minka Lavery 8274-A357-L Instructions / Assembly

INSTALLATION INSTRUCTIONS
Model # 8274-L
WARNING!
READ AND SAVE THESE INSTRUCTIONS
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig.1)
1.
2.
3.
4.
Shut of the power at the circuit breaker and remove the old
fixture including the mounting hardware.
Thread nipple (G) into loop (I) until snug.
Thread other end of nipple (G) into the crossbar (F) until snug
and secure with lock washer (E) and hex nut (D). Note the
length of nipple (G) into crossbar (F) may be adjusted.
Attach the crossbar assembly to the ceiling outlet box with
screws (B).
Fig. 1
A
Set:
Cross Bar
Ground screw(1)
Mounting screws(2)
HANGING THE FIXTURE (Fig.1)
5.
6.
7.
8.
9.
Determine the desired hanging height and remove the excess
chain with proper chain pliers to avoid damaging the finish.
Open one end of the chain and connect it to the fixture chain
loop (L) and close the link. Thread the wire carefully through
the chain links.
Place lock ring (J) followed by canopy (H) over the chain and
allow them to carefully rest on the fixture body.
Open the other end of the chain and attach it to chain loop (I)
and close the link.
Feed the wires through loop (I), and nipple (G).
CONNECTING THE WIRES (Fig.3)
10. Connect the electrical wires as shown in Fig. 2, making sure
that all wire connectors are secured. If your outlet has a ground
wire (green or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the
crossbar using the green screw provided. Tuck the wire
connections neatly into the junction box.
FINISHING THE INSTALLATION (Fig. 1)
11. Raise the canopy (H) to the ceiling and secure with lock ring (J).
12. Bulb (M) information (1 x AC LED 10W included.) (DO
NOT EXCEED THE MAXIMUM WATTAGE RATING)
(NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
F ig.2
FI XTURE
WI RES
GREEN OR
BARE
COPPER
( GROUND)
FI XTURE
WI RES
WHI TE
FI XTURE
WI RES
BLACK
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps for
more details (Fig.3).
a. Shut off power, remove the fixture body (O) by loosening
screws (N) (Fig.1), then remove aluminum panel (Q) by
loosening screws (R).
b. Remove wire nuts (P), remove screws (S) and carefully
remove LED module (M) for re-lamping. Note: The LED
module should be provided by a specified supplier.
c. For better heat dissipation the LED module (M) should be
installed with the heat transfer material (V) when relamping.
Your installation is now complete. Return power to the junction box
and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased.
HOUSE
WI RES
BLACK
( HOT)
HOUSE
WI RES
WHI TE
( NEUTRAL)
HOUSE
WI RES
GREEN OR
BARE COPPER( GROUND)
Fig. 3
V (Graphite sheet)
U(Glass)
T(Module ring)
P
Q
R
M (LED module)
S(Module screws)
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.