the great outdoors by Minka Lavery 8264-66-L Instructions / Assembly

INSTALLATION INSTRUCTIONS
Model # 8264-L
WARNING!
READ AND SAVE THESE INSTRUCTIONS
S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig.1)
1.
2.
3.
4.
Shut of the power at the circuit breaker and remove the old
fixture including the mounting hardware.
Thread nipple (L) into loop (F) until snug.
Thread other end of nipple (L) into the cross bar (B) until snug
and secure with lock washer and hex nut. Note the length of
nipple (L) into cross bar (B) may be adjusted.
Attach the cross bar assembly to the ceiling outlet box with
screws (C), the side of the crossbar marked "GND" must face
out. Tighten screws securely with screwdriver.
Fig. 1
A
B Set:
Cross Bar
C
Ground Screw 1
Mounting Screws 2
D
()
()
L
E
HANGING THE FIXTURE (Fig.1)
5.
6.
7.
8.
9.
Determine the desired hanging height and remove the excess
chain with proper chain pliers to avoid damaging the finish.
Open one end of the chain and connect it to the fixture chain
loop (I) and close the link. Thread the wire carefully through the
chain links.
Place lock ring (G) followed by canopy (E) over the chain and
allow them to carefully rest on the fixture body.
Open the other end of the chain and attach it to chain loop (F)
and close the link.
Feed the wires through loop (F), and nipple (L).
F
G
H
I
J
CONNECTING THE WIRES (Fig.2)
10. Connect the electrical wires as shown in Fig. 2, making sure
K
that all wire connectors are secured. If your outlet has a ground
wire (green or bare copper), connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the
crossbar using the green screw provided. Tuck the wire
connections neatly into the junction box.
FINISHING THE INSTALLATION (Fig. 1)
11. Raise the canopy (E) to the ceiling and secure with lock ring
(G).
12. Bulb ( J ) information (1 x AC LED 10W included.) (DO
NOT EXCEED THE MAXIMUM WATTAGE RATING)
(NE PAS DEPASSER LA PUISSANCE NOMINALE
MAXIMALE!)
F ig.2
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician
without cutting of wire and without damage to any decorative
element to which the fixture is attached. See installation steps for
more details (Fig.3).
FIXTURE
WIRES
GREEN OR
BARE
COPPER
(GROUND)
FIXTURE
WIRES
WHITE
FIXTURE
WIRES
BLACK
HOUSE
WIRES
BLACK
(HOT)
HOUSE
WIRES
WHITE
(NEUTRAL)
HOUSE
WIRES
GREEN OR
BARE COPPER(GROUND)
Fig.3
a. Shut off power and unplug the male and female jacket
(O&P).
b. Loosen module screws (K) and carefully remove LED
module (J) for re-lamping. Note: The LED module should
be provided by a specified supplier.
c. For better heat dissipation the LED module (J) should be
installed with the heat transfer material (Q) when relamping.
Your installation is now complete. Return power to the junction box
and test the fixture.
P (Female Jacket)
Aluminum Panel
O (Male Jacket)
N (Glass)
M (Module Ring)
Q (Graphite Sheet)
J (LED Module)
K (Module Screws)
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the
fixture purchased.
Notice:It is important to use proper chain pliers(not included)
To OPEN and CLOSE the chain included with this fixture.Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.