Kenroy Home 32618ORB Installation Guide

 MODEL: 326180RB
PACKING DIAGRAM
CARDBOARD >
CARDBOARD
A0 - SHADE
ZN
.CA TITLE 20 > )
BACKPLATE ASSEMBLY,
MOUNTING PLATE,
SOCKEY RING (2 PCS)
& (3) SMALL SCREWS.
(2) CORD COVERS,
MOUNTING CHANNEL,
(2) MOUNTING SCREWS,
(6) WOOD SCREWS AND
(6) PLASTIC ANCHORS.
“
<
SOCKET RING oom
SHADE |
32618SHORB =
(REPLACEMENT
PART) «| CORD COVER
SMALL SCREW
(3 PCS)
/ PLASTIC
— 7 ANCHOR
AR _ y (2 PCS)
FT SOCKET |
__L | ASSEMBLY у
| | #-т- WOOD SCREW
BACKPLATE u (2 PES)
SWITCH — e í
AA
/
|
= / CHANNEL
o о o Ш y
I=
: O) , ~ CORD COVER
35 POWER CORD =| CORD COVER
—
Axi UL
m= -~ CORD
ASSEMBLY INSTRUCTIONS CORD COVER ASSEMBLY
READ AND SAVE THESE INSTRUCTIONS
READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY.
THIS LAMP SHOULD TAKE APPROXIMATELY 5 MINUTES TO ASSEMBLE.
MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED.
CAUTION: INJURY TO PERSONS AND DAMAGE TO THE LAMP AND/OR MOUNTING SURFACE MAY RESULT IF THE LAMP IS
PULLED AWAY FROM THE SURFACE: TO REDUCE THE LIKELIHOOD OF SUCH INJURY OR DAMAGE, MOUNT ONLY ON A SURFACE
THAT IS MECHANICALLY SOUND.
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT: SCREWDRIVER AND DRILL.
UNPACK THE LAMP: CHECK THE CONTENTS OF THE BOX. YOU SHOULD HAVE RECEIVED THE FOLLOWING:
BACKPLATE, SHADE, SOCKET ASSEMBLY AND ARM. PACKAGE: (2) 8-32 x 1—1/4" MOUNTING
SCREWS, (6) WOOD SCREWS, (6) PLASTIC ANCHORS, (2) CORD COVERS, MOUNTING CHANNEL.
NOTE: IF USING POWER CORD FOLLOW INSTRUCTIONS BELOW. IF WIRING TO AN OUTLET BOX PROCEED
TO OUTLET BOX INSTALLATION INSTRUCTIONS.
ASSEMBLE THE FIXTURE:
NOTE: SWING THE SWING ARM, IF THE SWING ARM IS HARD TO SWING OR HAVE ABNORMAL SOUND, PUT A DROP OF
WD—40 OR SIMILAR PRODUCT ON THE JOINTS AND LET IT SIT OVERNIGHT. DRY WITH A SOFT CLOTH PRIOR TO ASSEMBLY.
1. REMOVE MOUNTING PLATE FROM BACKPLATE ASSEMBLY BY UNSCREWING (3) SMALL SCREWS.
2. POSITION THE MOUNTING PLATE ON THE WALL AT DESIRED LOCATION AND MARK THE PLACE FOR THE PLASTIC ANCHORS
TO BE INSTALLED.
3. DRILL PILOT HOLES ON THE MARKED SPOTS AND INSERT PLASTIC ANCHORS. (IF FASTENING WITH WOOD SCREWS TO
STUD, SKIP THIS STEP). (NOTE: THE MOUNTING PLATE SHOULD BE MOUNTED ON A WALL STUD USING A SCREWDRIVER. IF
MOUNTING ON A HOLLOW AREA, DRILL 1/4” PILOT HOLES AND INSERT PLASTIC ANCHORS WHERE THE LOCATION WAS
MARKED.
4. jeer THE MOUNTING PLATE TO THE PLASTIC ANCHORS OR THE SPOTS THAT YOU MARKED ON STUD AND SECURE WITH
(4) WOOD SCREWS.
5. RAISE THE BACKPLATE ASSEMBLY TO THE WALL, THEN SECURE THE BACKPLATE ASSEMBLY TO MOUNTING PLATE WITH (3)
SMALL SCREWS REMOVED ABOVE.
6. PLACE A SHADE OVER THE SOCKET, AND THEN SECURE WITH THE SOCKET RING.
7. INSTALL A 100 WATT MAX. MEDIUM BASE TYPE "A” BULB (NOT INCLUDED) INTO SOCKET.
8. TO INSTALL CORD COVER, MOUNT CHANNEL ON THE WALL WITH WOOD SCREWS AND PLASTIC ANCHORS,
WITH CORD BEHIND COVERS, PRESS CORD COVERS ONTO CHANNEL. U
9. PLUG THE POWER CORD INTO AN OUTLET AND TURN ON AT SWITCH. eL
12/2014 326180RB INSTRUCTIONS
SOCKET RING A
SHADE
32618SHORB —
(REPLACEMENT
PART)
MOUNTING
BLACK PLATE
- FIXTURE
WIRE 8/32 x 1-1/4"
SMALL SCREW SCREWS (2 PCS)
(3 Pes) | WIRE
SOCKET n Jo CONNECTOR (3)
ASSEMBLY —- я == BLACK
BACKPLATE EM | SUPPLY MIRE
/ m TT — WHITE SUPPLY
AR N
> WIRE
| 0
SWITCH _ ; SUPPLY
TIL GROUND WIRE
<
]
———
i OUTLET BOX
FIXTURE WHITE GREEN
GROUND WIRE Re RE GROUND SCREW
OUTLET BOX INSTALLATION WALL
READ AND SAVE THESE INSTRUCTIONS
CAUTION: TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL.
IF YOU ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF POSITION.
SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES.
** IF YOU DO NOT HAVE ELECTRICAL WIRING EXPERIENCE, HAVE YOUR FIXTURE INSTALLED BY A QUALIFIED LICENSED
ELECTRICIAN.
*** THIS FIXTURE IS TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE WEIGHT OF THIS FIXTURE.
THE OUTLET BOX MUST BE DIRECTLY SUPPORTED BY THE BUILDING STRUCTURE.
NOTE: IF WIRING TO OUTLET BOX FOLLOW INSTRUCTIONS BELOW. IF USING POWER CORD,
PROCEED TO ASSEMBLY INSTRUCTIONS.
INSTALL THE FIXTURE
1. REMOVE MOUNTING PLATE FROM BACKPLATE ASSEMBLY BY UNSCREWING (3) SMALL SCREWS.
2. REMOVE POWER CORD. (REFER TO "REMOVING THE POWER CORD” INSTRUCTIONS).
3. ATTACH MOUNTING PLATE TO OUTLET BOX USING TWO SCREWS PROVIDED WITH THE OUTLET BOX. (NOTE: IF THE SCREWS
WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1—1/4" SCREWS PROVIDED IN THE MOUNTING HARDWARE
PACKAGE).
4. CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON
WIRE CONNECTOR PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME
MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE THEN CONNECT
THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE CONNECTOR
PROVIDED.
3S. RAISE BACKPLATE ASSEMBLY TO THE WALL AND CAREFULLY TUCK THE WIRES INSIDE THE OUTLET BOX. SPREAD THE
ELECTRICAL SPLICES SO THAT THE BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE
OTHER SIDE. THEN SECURE THE BACKPLATE ASSEMBLY TO MOUNTING PLATE WITH (3) SMALL SCREWS REMOVED ABOVE.
6. PLACE A SHADE OVER THE SOCKET, AND THEN SECURE WITH THE SOCKET RING.
7. INSTALL A 100 WATT MAX. MEDIUM BASE TYPE “A” BULB (NOT INCLUDED) INTO SOCKET.
8. RESTORE POWER AND TURN ON AT SWITCH, YOUR NEW FIXTURE IS NOW READY FOR USE.
® L 12/2014 326180RB INSTRUCTIONS
°C
REMOVING THE POWER CORD
WIRE CONNECTOR
(2 PCS)
GROUND WIRE
——BACKPLATE
REMOVE
\.
SAFETY KNOT A
— POWER CORD
REMOVING THE POWER CORD
* THE POWER CORD IS THE WIRE THAT ENTERS THROUGH THE BOTTOM OF BACKPLATE.
1. REMOVE THE (2) WIRE CONNECTORS THAT CONNECT TO POWER CORD BY TWISTING
COUNTER CLOCKWISE. (SEE DIAGRAM)
2. UNTIE SAFETY KNOT AND PULL POWER CORD OUT THROUGH BOTTOM OF BACKPLATE.
3. FOLLOW OUTLET BOX INSTALLATION INSTRUCTIONS FOR WIRING TO AN OUTLET BOX.
12/2014 326180RB INSTRUCTIONS