Sea Gull Lighting 6022-15 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
ASSEMBLY
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Under no circumstances should a
fixture be hung on house electrical wires, nor should a swag type
fixture be installed on a ceiling which contains a radiant type heating
system. Read instructions carefully. If you are unclear as to how
to proceed, consult a qualified electrician.
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 2:
Place the fixture cup (Z), round nut (Y), and plastic cap (D), in that
order onto cord (E) and socket nipple (C). Secure these parts with
round nut (Y). Thread on plastic cap (D) finger tight.
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
*OUTLET BOX
*WIRE
CONNECTORS
MOUNTING
BAR (A)
*WIRE
CONNECTORS
*OUTLET
BOX SCREWS
NIPPLE (C)
MOUNTING
BAR (A)
HEX NUT (B)
*OUTLET BOX
SCREWS
CANOPY (H)
ROUND NUT (G)
PLASTIC CAP (F)
GREEN
GROUNDING
SCREW (R)
NUT (B)
NIPPLE (C)
CORD (E)
FIGURE 2
*NOT INCLUDED
PLASTIC CAP (D)
ROUND NUT (Y)
SOCKET NIPPLE (O)
FIXTURE CUP (Z)
NOTE: FIGURE 1 ILLUSTRATES THE INSTALLATION OF YOUR
NEW LIGHTING FIXTURE. THIS IS A REPRESENTATIVE
DRAWING AND MAY NOT MATCH THE STYLE OF YOUR
FIXTURE.
FITTER (P)
GLOBE (N)
FIGURE 1
*NOT INCLUDED
Installation And Safety
Instruction
HC-111 092800
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-111
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Slide plastic cap (F), round nut (Y), canopy (H), hex nut (B),
nipple (C) and mounting bar (A), in that order, onto cord (E).
STEP 2:
Screw nipple (C) into mounting bar (A), 3 turns, and secure to
bar (A) with hex nut (B).
STEP 3:
Pull cord (E) through mounting bar (A) to desired length and knot
cord (E).
STEP 4:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied).
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (R) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (R) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all
fixtures to have ground wires. These fixtures still meet all UL
specifications. The listing mark of Underwriters on the product
identifies products manufactured under its listing and Follow-Up
Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and secure with round
nut (Y), and plastic cap (F).
STEP 2:
Install lamp in socket.
STEP 3:
Assembly For Fixture With Globe: Unscrew round nut (Y) and
plastic cap (D) from fitter (P) to release fixture cup (Z). Place fitter
(P) into globe (N). Seat fitter (P) in position, drop fixture cup (Z),
and secure with round nut (Y) and plastic cap (D).
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
The white electrical cord on this fixture has printing on it. This
information is required to be there by Underwriters Laboratories. If,
after you have purchased this product and the presence of this
printing is objectionable to you, you may remove it by the following
method.
Before wiring your fixture to your power source:
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
1. Gently wipe the printing with a cloth slightly dampened
with either nail polish remover or paint thinner. Do not
soak the wire--a slight dampening is enough.
2. After the print is removed, wipe with cloth slightly
dampened with fresh water.
3. Proceed to hang fixture as per normal instructions.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.