Sea Gull Lighting 44061-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
GREEN
GROUNDING
SCREW (G)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GROUNDWIRE
BACK
PLATE (C)
UNIVERSAL
MOUNTING
BAR (D)
CAP
NUTS
(H)
GLASS
RETAINING
SCREWS (L)
GLASS (J)
*WIRE
CONNECTOR
MOUNTING SCREWS (F)
FIGURE 1
*NOT SUPPLIED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
*OUTLET
BOX
GREEN
GROUNDING
SCREW (G)
GROUND
WIRE
*OUTLET
BOX
SCREWS
Installation And Safety
Instruction
HC-1329 012808
*WIRE CONNECTOR
UNIVERSAL
MOUNTING
BAR (D)
FIGURE 2
MOUNTING
SCREWS (F)
*NOT SUPPLIED
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
HC-1329
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Thread mounting screws (F) into holes of universal mounting bar (D)
and run mounting screws (F) all the way down to their heads.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D). Make
sure mounting screws (F) are perfectly horizontal so fixture hangs
properly.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (D). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (G) on the
universal mounting bar (D) if uninsulated wire is on the universal
mounting bar (D), connect the ground wire from the fixture (if
supplied) and the outlet box to it using a small wire connector (not
supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
STEP 2:
After wires are connected, tuck them carefully inside outlet box. Push
the backplate (C) firmly over the mounting screws (F) and against the
wall. Secure backplate (C) in place by threading cap nuts (H) onto
mounting screws (F).
STEP 3:
Place glass (J) around socket and secure in place by tightening glass
retaining screws (L). Finger tighten only. Do not over tighten.
STEP 4:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
Install lamps.
CLEANING
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth. (Seen best
when viewed from wire end.) To separate wires, grasp the ends of
each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.