Sea Gull Lighting 44854-965 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
•
•
•
•
•
•
120308
CLEANING
IMPORTANT SAFETY INSTRUCTIONS
•
HC-1520
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
BEFORE YOU BEGIN
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
INSTALLATION
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Place back plate (D) against wall and mark location for drywall
anchors. Remove back plate (D) and drill appropriate sized holes into
drywall for anchors.
STEP 2:
Pull supply wires through appropriate opening in backplate (D). Place
backplate (D) against wall and secure by installing dry wall screws
into anchors. Install outlet box screws (not supplied) into outlet box
through appropriate openings in backplate (D) if applicable.
DRYWALL
ANCHOR
BACKPLATE
(D)
FIXTURE
GROUND
WIRE
GREEN
GROUNDING
SCREW (G)
*SUPPLY
GROUND
WIRE
MOUNTING
SCREWS (F)
STEP 1
STEP 2
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1520
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 3:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 5:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
canopy (I) firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place by threading cap nuts (E) onto fixture
mounting screws (F).
STEP 6:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
backplate (D). Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (G) on the backplate (D) if
uninsulated wire is on the backplate (D), connect the ground wire
from the fixture (if supplied) and the outlet box to it using a small wire
connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
*SUPPLY
GROUND
WIRE
FIXTURE
GROUND
WIRE
Place shade (A) on socket cup (B) and secure by threading retaining
ring (H) onto socket.
STEP 7:
Install lamps (not supplied).
*WIRE
CONNECTOR
GREEN
GROUNDING
SCREW (G)
BACKPLATE
(D)
STEP 4
STEP 5
STEP 3
MOUNTING
SCREWS (F)
SOCKET
CUP (B)
SHADE
(A)
STEP 6
CAP NUTS (E)
RETAINING
RING (H)
CANOPY (I)
FIGURE 1
*NOT INCLUDED