Sea Gull Lighting 31363-965 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
GROUNDING AND MOUNTING BAR LOCK UP
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
*OUTLET BOX
*GROUND WIRE
*WIRE
CONNECTORS
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
*OUTLET BOX
*WIRE CONNECTORS
*GROUND WIRE
MOUNTING BAR (A)
GREEN
GROUNDING
SCREW (D)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT INCLUDED
*OUTLET BOX
SCREWS
GROUND WIRE (F)
SCREW COLLAR (E)
CHAIN (S)
WARNING: TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT TO OUTLET BOX OR
SUPPORTING SYSTEM ABLE TO SUPPORT
THE WEIGHT OF THE FIXTURE.
FIXTURE LOOP (I)
GLASS (J)
SOCKET
ASSEMBLY (K)
*NOT SUPPLIED
FIGURE 1
ASSEMBLY
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
Installation And
Safety Instruction
HC-706
022205
STEP 1:
Rotate arms.
STEP 2:
Attach loop (I) to top of fixture (if applicable).
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
INSTALLATION
HC-706
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (E) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and
attach it to the screw collar (E) which has been mounted to the
ceiling nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 4:
Lace wires up through chain (S) and pass wires through holes in
screw collar (E). We recommend lacing wire up through every other
link of chain (S).
STEP 5:
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and screw the screw collar
ring (G) to the screw collar (E).
STEP 2:
Place glass (J) in socket assembly (K).
STEP 3:
Install lamps.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.