Sea Gull Lighting 41115-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FIGURE 1
*NOT SUPPLIED
BACKPLATE (A)
GLASS
SUPPORT
BRACE (D)
*OUTLET BOX
GLASS (E)
FIGURE 2
*WIRE
CONNECTOR
GROUND
WIRE
CAP
NUTS (R)
*OUTLET BOX
SCREWS
GLASS
SUPPORT
BRACE (D)
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Read instructions carefully. If you are unclear
as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
GLASS (E)
FIGURE 3
ASSEMBLY
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1, 2 & 3. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 1
Remove glass support brace (D) from backplate (A).
STEP 2
Install glass through support brace (D).
NOTE: FOR FIXTURES PROVIDED WITH 75˚C OR 90˚C SUPPLY WIRE WARNING ONLY-(THESE WARNINGS ARE PROVIDED ON THE U.L. LABEL AND ON THE FIXTURE CARTON):
RISK OF FIRE. MOST DWELLINGS BUILT BEFORE 1985 HAVE
SUPPLY WIRE RATED 60˚C. CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING.
Installation And
Safety Instruction
HC-844
022205
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-844
STEP 1:
Punch out appropriate holes in backplate [A], if applicable, to correspond with holes in outlet box.
STEP 2:
Push socket wires thru plastic bushing (If applicable).
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: Wrap the ground wire from the fixture (if supplied) and the ground wire from the outlet box (bare metal
or green insulated wire) around the green grounding screw on the
back plate (A); (Or if applicable).The green grounding screw is to be
inserted into the hole with two raised dimples provided on the
back plate (A).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
Tuck wires into outlet box. Attach backplate (A) to outlet box by
placing outlet box screws (not supplied) through punched out holes
in backplate (A).
STEP 2:
Install lamp.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
STEP 3:
Secure support brace (D) and glass (E) to backplate with cap nuts
(R).
CLEANING
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.