Sea Gull Lighting 66060-782 Installation Guide

Installation And Safety Instructions
HC-225
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
071608
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
To reduce the risk of fire, electric shock, or personal injury, mount
to outlet box or supporting system able to support the weight of
the fixture.
Read instructions carefully.
Save these instructions.
NOTE: FOR FIXTURES PROVIDED WITH 75˚ C OR 90˚ C SUPPLY WIRE
WARNING ONLY-(THESE WARNINGS ARE PROVIDED ON THE U.L.
LABEL AND ON THE FIXTURE CARTON): RISK OF FIRE. MOST
DWELLINGS BUILT BEFORE 1985 HAVE SUPPLY WIRE RATED 60˚ C.
CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING.
IF SUPPLY WIRES ARE LOCATED WITHIN 3" OF BALLAST, USE WIRE
RATED FOR AT LEAST 90˚ C.
*OUTLET BOX
GROUND
WIRE (F)
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
NIPPLE (C)
NUT &
LOCKWASHER
(B)
CANOPY (H)
SCREW
COLLAR (E)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
CHAIN (S)
SCREW
COLLAR
RING (G)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
LOOP (I)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
SOCKET
ASSEMBLY
(K)
STEP 1:
SHADE (J)
Attach loop (I) to top of fixture (if applicable).
DECORATIVE
TRIM RING
(M)
STEP 2:
Insert decorative trim ring (M) over shade (J) (If applicable).
INSTALLATION
SUPPORT
RING (N)
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
RETAINING
RING (L)
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Attach screw collar (E) to nipple (C).
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-225
STEP 2:
Using 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and attach
it to the screw collar (E) which has been mounted to the ceiling
nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 4:
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and thread the screw collar
ring (G) to the screw collar (E).
STEP 2:
Raise shade (J) to socket assembly (K), insert support ring (N), (If
applicable), and secure in place by threading retaining ring (L) onto
socket.
STEP 3:
Install lamp (not supplied).
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.