Sea Gull Lighting 94113-71 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
• You don’t need special tools to install this fixture. Be sure
to follow the steps in the order given. Read instructions
carefully.
• Be sure the electricity to the system you are working on
is turned off; either the fuse removed or the circuit
breaker set at off.
• If you are unclear as to how to proceed, contact a
qualified electrician.
• Use of other manufacturers components will void
warranty, listing, and create a potential safety hazard.
• Proper wiring is essential for the safe operation of this
fixture.
• Save these instructions.
UNIVERSAL GROUND
MOUNTING WIRE
BAR (F)
WIRE
CONNECTOR
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
MOUNTING
ARMS (C)
RETAINING
SCREWS (E)
GLASS (D)
CAP
NUTS (B)
MOUNTING
SCREWS (G)
CANOPY (A)
*NOT SUPPLIED
FIGURE 1
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (H)
*OUTLET BOX
SCREWS
GROUND
WIRE
MOUNTING
SCREWS (G)
WIRE CONNECTOR
FIGURE 2
UNIVERSAL
MOUNTING
BAR (F)
LR-109
011408
*NOT SUPPLIED
www.SeaGullLighting.com
INSTALLATION
LR-109
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert mounting screws (G) in threaded holes of universal mounting
bar (F). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (F) against outlet box (not supplied)
and secure in place using outlet box screws (not supplied). Be sure
the mounting screws (G) are perfectly horizontal so fixture hangs
straight.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (H)
is to be inserted into the hole with two raised dimples provided on
the universal mounting bar (F). Wrap the ground wire from the fixture
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (H) on the
universal mounting bar (F) if uninsulated wire is on the universal
mounting bar (F), connect the ground wire from the fixture and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (A) over mounting screws (G) and secure in place
with cap nuts (B).
STEP 2:
Install lamp and glass enclosure.
STEP 3:
Place glass (D) over canopy (A) and thread retaining screws (E)
through glass holes and on to mounting arms (C) to secure.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread
the connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
pull the wires out, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.