Sea Gull Lighting 59271LE-15 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully
In order for this lighting fixture to operate properly the buildings
electrical system must be grounded.
Save these instructions.
ASSEMBLY
NOTE: Because of the size of this fixture, we recommend two
people to install this fixture.
STEP 1:
Remove center cover (B) by squeezing cover together and pulling out
of tabs (C).
STEP 2:
Remove 7/8" diameter wire exit plug and oval mounting knock-outs by
taking a screwdriver and punching out plug and knock-outs from back
side of fixture pan (A).
Do not install on a ceiling that would cause the lift and shift
mechanism to disengage (ie. slope ceiling, drop ceiling etc.)
NOTE: FOR FIXTURES PROVIDED WITH 75°C OR 90°C SUPPLY WIRE
WARNING ONLY: RISK OF FIRE. MOST DWELLINGS BUILT BEFORE 1985
HAVE SUPPLY WIRE RATED 60°C. CONSULT A QUALIFIED ELECTRICIAN
BEFORE INSTALLING.
7/8" WIRE EXIT
TABS (C)
MOUNTING HOLE
BALLAST
CENTER COVER (B)
FIGURE 1
FIXTURE PAN (A)
DIFFUSER (D)
Installation And Safety
Instruction
HC-1297 092807
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
FIGURE 2
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
INSTALLATION
HC-1297
IF SUPPLY WIRES ARE LOCATED WITHIN
3" OF BALLAST, USE WIRE RATED FOR
AT LEAST 90°C
STEP 1:
Determine exact location on ceiling for fixture placement.
STEP 2:
Feed the black and white ballast wires through the 7/8” wire exit hole
of the fixture pan (A).
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw is to
be inserted into the hole with two raised dimples provided on the
fixture pan. Wrap the ground wire from the fixture (if supplied) and the
ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw on the fixture pan. If
uninsulated wire is on the chassis, connect the ground wire from
the fixture (if supplied) and the outlet box to it using a small wire
connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 3:
Make sure no bare wires can be seen outside wire connectors.
Mount fixture to ceiling. When mounting to drywall use molly bolts.
When mounting to ceiling joists use 1 1/4" screws.
STEP 1:
Install center cover (B) over fixture by squeezing center cover (B)
together and insert under tabs (C).
STEP 4:
WIRING:
If applicable, insert supply wires into supplied
ballast quick connect. Proceed to step 5.
Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 2:
Install lamps.
STEP 3:
Secure diffuser (D) by placing one edge of diffuser (D) over one lip
of fixture pan (A) so clips on diffuser lock to fixture pan (A). Repeat
with other side of diffuser (D).
NOTE: IN ORDER FOR THIS LIGHTING FIXTURE TO OPERATE
PROPERLY, THE BUILDING’S ELECTRICAL SYSTEM MUST BE
GROUNDED. IF YOU ARE UNCLEAR AS HOW TO PROCEED,
CONSULT A QUALIFIED ELECTRICIAN.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG