Sea Gull Lighting 65521-845 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
off; either the fuse removed or the circuit breaker set at off.
any of the screws or parts which are needed to install this fixture.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*OUTLET BOX
*GROUND WIRE
*WIRE CONNECTORS
*WIRE
CONNECTORS
*GROUND WIRE
MOUNTING BAR (A)
*OUTLET BOX
SCREWS
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
GROUND WIRE (F)
SCREW COLLAR (E)
CANOPY (H)
SCREW COLLAR
RING (G)
GREEN
GROUNDING
SCREW (D)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT SUPPLIED
CHAIN (S)
FIXTURE LOOP (I)
CENTER PIPE (M)
FIXTURE
FRAME (N)
DIFFUSER (O)
HEX NUT (Y)
FIGURE 1
RUBBER WASHER (Z)
*NOT SUPPLIED
FINIAL (X)
Installation And
Safety Instruction
HC-1154
081307
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-1154
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and
attach it to the screw collar (E) which has been mounted to the
ceiling nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and thread the screw collar
ring (G) to the screw collar (E).
STEP 2:
STEP 4:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
Place diffuser (O) onto center pipe (M) and secure by threading
rubber washer (Z), hex nut (Y), and finial (X) onto center pipe (M).
STEP 3:
Install lamps.
STEP 4:
Position top diffuser (W) over mounting holes and secure in place by
threading retaining screws (V) into holes. Place top diffusers (W)
onto provided mounting screws and secure with diffuser cap nuts (V).
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
TOP
DIFFUSERS
(W)
RETAINING
SCREWS
(V)
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
FIGURE 3
*NOT INCLUDED