Sea Gull Lighting 51251-824 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Read instructions carefully. If you are unclear
as to how to proceed, consult a qualified electrician.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
*NOTE: If the following parts are not supplied, or they are
factory assembled; proceed to the next assembly step.
STEP 1:
Attached top assembly to fixture center column.
STEP 2:
Rotate arms on top assembly.
STEP 3:
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT TO
OUTLET BOX OR SUPPORTING SYSTEM ABLE TO
SUPPORT THE WEIGHT OF THE FIXTURE.
Remove (3) ball studs from top of cage.
STEP 4:
Secure arms to fixture cage with ball studs (nut will not be used).
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
*OUTLET BOX
*GROUND WIRE
*WIRE CONNECTORS
NUT (B)
NIPPLE (C)
*WIRE
CONNECTORS
MOUNTING BAR (A)
*OUTLET BOX SCREWS
GROUND WIRE (S)
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
SCREW COLLAR (D)
CANOPY (E)
SCREW COLLAR RING (F)
CHAIN (G)
TOP ASSEMBLY
GREEN
GROUNDING
SCREW (R)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT INCLUDED
FIXTURE LOOP (I)
ARMS
BALL
STUDS
Installation And
Safety Instruction
HC-527
012606
Line art shown may not exactly match the fixture
enclosed. However, the installation instructions do
apply to this fixture.
*NOT SUPPLIED
FIG. 1
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
HC-527
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (D) to nipple (C).
STEP 2:
Using 2 pairs of pliers, open one link of chain (G), and connect to
the fixture loop (I) at the top of the fixture.
STEP 3:
Slide the screw collar ring (F) and the canopy (E), in that order, over
chain (G). Open one link on the other end of the chain (G) and
attach it to the screw collar (D) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
Lace wires up through chain (G) and pass wires through holes in
screw collar (D). We recommend lacing wire up through every other
link of chain (G).
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (R) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (R) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (E) against ceiling and screw the screw collar
ring (F) to screw collar (D).
STEP 2:
Install candle covers (if applicable).
STEP 3:
Install lamps.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.