Sea Gull Lighting 61035-962 Installation Guide

HC-387
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this
fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Proper wiring is essential to the safe operation of this fixture.
Save these instructions.
060909
FIGURE 1
*NOT SUPPLIED
FOR STEM MOUNT
*OUTLET BOX
NOTE:
THIS
FIXTURE
CAN BE
HUNG
USING 1, 2,
OR 3 RODS.
SELECT THE
NUMBER
OF RODS
DESIRED.
MOUNTING
BAR (B)
MOUNTING
SCREWS (I)
*WIRE
CONNECTORS
CANOPY (G)
CAP NUTS (F)
COUPLING (J)
CLEANING
ROD ASSEMBLY (E)
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do
not use abrasive materials such as scouring pads or powders, steel wool
or abrasive paper.
*NOTE: For Solid Copper Fixtures. Use a good quality automotive wax at
least twice a year to protect your fixture. If this additional care is not taken,
your fixture will turn into a Patina Finish over time.
SOCKET
ASSEMBLY (U)
DIFFUSER (R)
ORDERING PARTS
DIFFUSER
RING (Z)
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering
parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts are
included, as shown in Figure 1. Be careful not to misplace any of the
screws or parts which are needed to install this fixture.
RETAINING RING (T)
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
FOR STEM MOUNT
*GROUND WIRE
STEP 1:
Secure rods together (if applicable).
STEP 2:
Feed the fixture wire from the socket assembly (U), through: the rod
assembly (E), and coupling (J) (mounted on canopy (G)).
MOUNTING
BAR (B)
MOUNTING
SCREWS (I)
*WIRE
CONNECTORS
STEP 3:
Secure rod assembly (E) to coupling (J), and socket assembly (U). Be sure
not to damage the fixture wire.
FIGURE 2
NUT (W)
ASSEMBLY FOR CHAIN HUNG
STEP 1:
*OUTLET BOX
SCREWS
*NOT INCLUDED
LOCK WASHER (H)
CANOPY (G)
CAP NUTS (F)
NIPPLE (M)
CANOPY LOOP (S)
Thread nipple (M) through canopy loop (S). Install canopy loop (S) through
canopy (G), secure with lockwasher (H) and nut (W) (if applicable).
STEP 2:
CHAIN (Y)
Install fixture loop (X) onto socket assembly (U).
FIXTURE LOOP (X)
STEP 3:
Feed the fixture wire from the socket assembly (U), through the fixture loop
(X), and canopy loop (S) (mounted on canopy (G)).
GREEN
GROUNDING
SCREW (D)
SOCKET ASSEMBLY (U)
FIGURE 3
ASSEMBLY FOR CHAIN HUNG
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
Thread nipple (M) through canopy loop (S). Install canopy loop (S) through
canopy (G), secure with lockwasher (H) and nut (W) (if applicable).
STEP 2:
FOR STEM MOUNT AND CHAIN HUNG
STEP 1:
After wires are connected, tuck them carefully inside outlet box and then
raise the canopy (G) against ceiling allowing for mounting screws (I) to
protrude through holes in canopy (G). Secure in place with cap nuts (F).
Install fixture loop (X) onto socket assembly (U).
STEP 3:
Feed the fixture wire from the socket assembly (U), through the fixture loop
(X), and canopy loop (S) (mounted on canopy (G)).
STEP 2:
Place diffuser ring (Z) over diffuser (R) (if applicable). Raise diffuser (R) to
socket assembly (U). Secure with retaining ring (T).
INSTALLATION
HC-387
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
MOUNTING BAR INSTALLATION
STEP 1:
Insert fixture mounting screws (I) in threaded holes of mounting bar (B).
Run fixture mounting screws (I) all the way down to the heads.
STEP 2:
Fasten mounting bar (B), to outlet box with outlet box screws (not
supplied). If installing with chain thread nipple (M) to center of mounting
bar (B) so five threads are past mounting bar (B). Secure by threading nut
(W) with lock washer (H) to mounting bar (B).
FOR CHAIN HUNG ONLY
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture.
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 2:
Lace fixture wire up through entire chain (Y) and pass through canopy loop
(S). We recommend lacing wire up through every other link of chain (Y).
WIRING
STEP 1:
A. Use a listed wire connector to connect the fixture hot wire (black wire,
or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire (white
wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can remove
the wires, carefully re-do the wiring connection.
STEP 2:
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
STEP 3:
Install lamp.