Sea Gull Lighting 6519-21 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned off;
either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing and
create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
Read instructions carefully.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the fixture
Save these instructions.
*OUTLET BOX
Carefully remove the fixture from the carton and check that all
parts are included, as shown in figure 1 and 2. Be careful not to
misplace any of the screws or parts which are needed to install
this fixture.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*WIRE
CONNECTORS
HEX NUT (B)
*HOUSE
GROUND WIRE
*WIRE
CONNECTORS
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
NIPPLE (C)
MOUNTING
BAR (A)
CANOPY (H)
*OUTLET
BOX
SCREWS
COLLAR RING (G)
ROUND NUT (G)
GREEN
GROUNDING
SCREW (R)
NUT (B)
NIPPLE (C)
PLASTIC CAP (F)
FIGURE 2
*NOT INCLUDED
CORD (E)
FIXTURE CUP (K)
GLASS RETAINING
SCREW (M)
GLASS (N)
Installation And Safety
Instruction
HC-103 091907
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
FIGURE 1
*NOT SUPPLIED
ITEM#_______________
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
INSTALLATION
HC-103
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Slide plastic cap (F), round nut (G), canopy (H), hex nut (B),
nipple (C) and mounting bar (A), in that order, onto cord.
STEP 2:
Screw nipple (C) into mounting bar (A), 3 turns, and secure to bar (A)
with hex nut (B).
STEP 3:
Pull cord (E) through shade (N), plastic cap (F), round nut (G),
canopy (H), nipple (C), and mounting bar (A) to desired length and
knot cord (E).
STEP 4:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied).
STEP 5:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (R) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (S) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (R) on the
mounting bar (A) if uninsulated wire is on the mounting bar (A),
connect the ground wire (S) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and secure with round
nut (G), and plastic cap (F).
STEP 2:
Thread the three glass retaining screws (M) into the fixture cup (K).
Place the glass (N) in to the cup (K) and tighten glass retaining
screws (M) until glass is secure. Do not overtighten glass retaining
screws (M), finger tighten only.
STEP 3:
Install lamp(s).
CLEANING
The white electrical cord on this fixture has printing on it. If, after you
have purchased this product and the presence of this printing is
objectionable to you, you may remove it by the following method.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Before wiring your fixture to your power source:
1. Gently wipe the printing with a cloth slightly dampened
with either nail polish remover or paint thinner. Do not
soak the wire--a slight dampening is enough.
2. After the print is removed, wipe with cloth slightly
dampened with fresh water.
3. Proceed to hang fixture as per normal instructions.
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.