Sea Gull Lighting 44850-782 Installation Guide

Installation And Safety Instructions
HC-1286
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
091007
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (G)
*OUTLET BOX
SCREWS
MOUNTING
SCREWS (F)
GROUND
WIRE
*WIRE CONNECTOR
UNIVERSAL
MOUNTING BAR (D)
FIGURE 2
*OUTLET BOX
UNIVERSAL GREEN
MOUNTING GROUNDING
SCREW (G)
BAR (D)
*NOT SUPPLIED
GROUND
WIRE
SOCKET
CUP (B)
SHADE (A)
MOUNTING
SCREWS (F)
FIGURE 1
CANOPY (I)
CAP
NUTS
(E)
RETAINING RING (C)
*NOT INCLUDED
INSTALLATION
HC-1286
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Insert fixture mounting screws (F) into universal mounting bar (D) and
run fixture mounting screws (F) all the way down to the heads.
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D). Make
sure fixture mounting screws (F) are perfectly horizontal so fixture
hangs straight.
STEP 3:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (D). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (G) on the
universal mounting bar (D) if uninsulated wire is on the universal
mounting bar (D), connect the ground wire from the fixture (if
supplied) and the outlet box to it using a small wire connector (not
supplied). NEVER CONNECT GROUND WIRE TO BLACK OR
WHITE POWER SUPPLY WIRES.
FINAL ASSEMBLY
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place with cap nuts (E).
STEP 2:
Place shade (A) on socket cup (B) and secure by threading retaining
ring (C) onto socket (Z).
STEP 3:
Install lamps.
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
CLEANING
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.