Sea Gull Lighting 31627-962 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1558
082709
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
*OUTLET BOX
STEP 2
MOUNTING
BAR (A)
NUT (B)
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
NIPPLE (C)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
SCREW
COLLAR (E)
CANOPY (H)
STEP 4
SCREW COLLAR
RING (G)
CHAIN (S)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 and Figure 2 . Be careful not to
misplace any of the screws or parts which are needed to install this
fixture.
STEP 3
FIXTURE LOOP (J)
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Rotate arms (M). Thread fixture loop (J) to top of fixture.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
STEP 1
STEP 3:
Using 2 pairs of pliers or chain breaks, open one link of chain (S) and
connect it to the fixture loop (J) at the top of the fixture. - Please be
sure to open chain link in an outward motion. Do not twist.
STEP 4:
Slide the screw collar ring (G) and canopy (H), in that order, over
chain (S). Open one link on the other end of the chain (S) and attach
it to the screw collar (E) which has been mounted to the nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
ARMS (M)
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1558
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
*OUTLET BOX
STEP 6:
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting
bar ground wire (pre attached) using the supplied wiring connector.
Gently try to remove the wires from the connector. If you can remove
the wires, carefully re-do the wiring connection.
STEP 5
*WIRE
CONNECTORS
MOUNTING
BAR (A)
NUT (B)
GREEN
GROUNDING
SCREW (D)
STEP 6
GROUND
WIRE (F)
FINAL ASSEMBLY
STEP 7
Make sure no bare wires can be seen outside wire connectors.
SCREW
COLLAR (E)
STEP 7:
CANOPY (H)
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (H) against ceiling and thread the screw collar ring (G)
to the screw collar (E).
STEP 8:
Place glass (R) in socket cup (I) and secure by threading retaining
ring (O) onto socket.
SCREW COLLAR
RING (G)
CHAIN (S)
FIXTURE LOOP (J)
STEP 9:
Install lamps (not supplied).
RETAINING
RING (O)
STEP 8
ARMS (M)
FIGURE 2
GLASS (R)
SOCKET
CUP (I)
*NOT INCLUDED