Sea Gull Lighting 65625BLE-962 Installation Guide

Installation And Safety Instructions
HC-1581
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
090809
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
To reduce the risk of fire, electric shock, or personal injury, mount
to outlet box or supporting system able to support the weight of
the fixture
Save these instructions.
*OUTLET BOX
*HOUSE
GROUND
WIRE
*WIRE
CONNECTORS
MOUNTING BAR (A)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
NUT (B)
*OUTLET BOX
SCREWS
GROUND WIRE (F)
NIPPLE (C)
CANOPY (H)
COLLAR (E)
COLLAR RING (I)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
CHAIN (J)
INSTALLATION
FIXTURE LOOP (K)
STEP 1:
Attach fixture loop (K) to top of fixture.
STEP 2:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Attach collar (E) to nipple (C).
SHADE (G)
STEP 3:
Using 2 pairs of pliers or chain breaks, open one link of chain (J) and
connect it to the fixture loop (K) at the top of the fixture. - Please be
sure to open chain link in an outward motion. Do not twist.
STEP 4:
Slide the collar ring (I) and canopy (H), in that order, over chain (J).
Open one link on the other end of the chain (J) and attach it to the
collar (E). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
GLASS
RETAINING
RING (L)
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1581
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
STEP 6:
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 7:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against ceiling and thread the collar ring (I)
to the collar (E).
STEP 8:
Raise shade (G) to socket and secure by threading glass retaining
ring (L) onto socket.
STEP 9:
Install self ballasted lamp (O) by twisting into socket (P).
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
FIXTURES WITH A ONE PIECE
LAMP / BALLAST COMBINATION
SELF BALLASTED
LAMP (O)
SOCKET (P)
FIGURE 2