the great outdoors by Minka Lavery 73064-246 Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model 73064-246 (Rev. 02/20/2014)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off the power at the fuse box or circuit breaker. If
necessary, remove the old fixture, including the
mounting hardware.
2. Carefully unpack your new fixture and lay out all parts
in a clear area. Take care not to lose any small parts
necessary for installation.
3. Install 1*40W ST58 bulb (s) (included) in accordance
with the fixture’s specification. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING) (NE PAS DEPASSER
LA PUISSANCE NOMINALE MAXIMALE!).
4. Align glass shade (E) to top cover (B).
5. While supporting the glass shade (E), align metal ring
(D) onto the bottom of glass shade (E). Secure
brackets (C) to top cover (B) and metal ring (D), with
cap nuts (A) to secure the glass into place.
6. Thread the nipple into the ceiling loop until snug.
7. Thread the other end of the nipple into the crossbar
until snug. Note: The length of the nipple into the
crossbar may be adjusted if necessary.
8. Use the lock washer and hex nut to secure the nipple
into the crossbar.
9. Take this crossbar assembly and mount it to ceiling
outlet box with mounting screws (Size: #8-32N*L0.5”).
The side of crossbar marked with “GND” must face out.
10. Determine the desired hanging height and use a pair of
proper chain pliers to remove and discard the excess
chain.
11. Open one end of chain and attach it to fixture loop and
close the chain. Slip the canopy and lock collar over
the chain and allow them to rest on the fixture body.
Open the other end of the chain and attach it to fixture
ceiling loop and close the chain.
12. Carefully lace the fixture’s wires through the chain.
Feed the fixture wires through the loop and nipple
assembly.
Fig. 1
Outlet Box
Hex Nut
Crossbar
Lock Washer
Mounting Screw
Nipple
Ceiling Loop
Chain
Canopy
Lock Collar
Wire
Loop
Chain#HCH2072-246
Fig. 2
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black
(Hot)
Fig. 3
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
A
B
Set# A-016
- Crossbar
- Ground screw
- Mounting Screw*2
CONNECTING THE WIRES (Fig. 2)
13. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the crossbar using the
green screw provided.
14. Tuck the wire connections neatly into the ceiling outlet
box. Raise the canopy to the ceiling and secure it with
the lock collar to the fixture ceiling loop.
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig. 3) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
C
E
D
A
LA-2394E