World Imports WI8002085 Installation Guide

CHAIN PENDANT FIXTURE
INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION (Continued)
Please read carefully and save these instructions, as you may need them at a later date.
WIRE (8) using a WIRE CONNECTOR (13)(not included). Place wiring and connections inside
the OUTLET BOX (1). (See Fig. 1)
CAUTION
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
7.
Slide the CANOPY (15) and the THREADED RING (16) up the CHAIN (17). Place the CANOPY
(15) over the OUTLET BOX (1) and secure it in place by screwing the THREADED RING (16)
onto the SCREW COLLAR LOOP (6). (See Fig. 1)
8.
Screw light bulbs into the lamp sockets and make sure they do not exceed the maximum wattage
specified on the fixture’s wattage rating label.
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If
you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by
referencing the illustrations on the installation instructions.
INSTALLATION IS NOW COMPLETED
ASSEMBLY AND INSTALLATION
1.
Take the parts out of the mounting package and thread both HEX NUTS (5) several turns onto each end
of the NIPPLE (4). Screw the end of the NIPPLE (4) several turns into the threaded hole of the
MOUNTING BRACKET (2) but do not tighten the HEX NUTS (5). Pull the SUPPLY WIRES (9 & 11)
and the SUPPLY GROUND WIRE (8) out from the OUTLET BOX (1) and attach the MOUNTING
BRACKET (2) assembly to the OUTLET BOX (1) using the slotted holes of the MOUNTING
BRACKET (2) and the MOUNTING SCREWS (3) provided. (See Fig. 1)
2.
Thread the SCREW COLLAR LOOP (6) onto the bottom end of the NIPPLE (4). Place the CANOPY
(15) over the OUTLET BOX (1) and adjust the SCREW COLLAR LOOP (6) and NIPPLE (4) until the
midpoint of the outside threads on the SCREW COLLAR LOOP (6) is centered (aligned) with the surface
of the CANOPY (15). Remove the CANOPY (15) and tighten both HEX NUTS (5) down on the
MOUNTING BRACKET (2) and the SCREW COLLAR LOOP (6).(See Fig. 1)
3.
Open up the end links of the CHAIN (17) and attach one end of the CHAIN (17) onto the FIXTURE
LOOP (18) of the top fount. Slide the THREADED RING (16) and the CANOPY (15) onto the CHAIN
(17) (in that order) and attach the other end of the CHAIN (17) to the SCREW COLLAR LOOP (6).
Close the ends of the chain links. (See Fig. 1)
4.
Feed the SAFETY CABLE (19) starting with the CHAIN (17) link attached to SCREW COLLAR LOOP
(6) , then through the hole of the OUTLET BOX (6) and attach the SAFETY CABLE (19) to the wood
screw (not included), then tighten the wood screw (not included) on the STRUCTURE SUPPORT BEAM
(20) of the building. (See Fig. 2)
5.
Unravel the fixture lead wires and FIXTURE GROUND WIRE (7) and thread them through every other
link of the CHAIN (17) starting with the chain link attached to the FIXTURE LOOP (18). Feed the
fixture lead wires and FIXTURE GROUND WIRE (7) through the SCREW COLLAR LOOP (6) and
NIPPLE (4) assembly. Pull the fixture lead wire and the FIXTURE GROUND WIRE (7) upward to
remove any excess slack. (See Fig. 1)
6.
Attach the power supply wires to the fixture lead wires by connecting the BLACK SUPPLY WIRE (9) to
the SMOOTH FIXTURE LEAD WIRE (10) and the WHITE SUPPLY WIRE (11) to the RIBBED
FIXTURE LEAD WIRE (12). Loop the FIXTURE GROUND WIRE (7) around the GROUND SCREW
(14) of the MOUNTING BRACKET (2). (Note: Be sure to provide an extra 3” length of the FIXTURE
GROUND WIRE (7).) Connect the remaining FIXTURE GROUND WIRE (7) to the SUPPLY
GROUND
FIG. 1
FIG. 2
1.
2.
3.
4.
5.
6.
7.
8.
OUTLET BOX
MOUNTING BRACKET
MOUNTING SCREW
NIPPLE
1/8” IPS HEX NUT
SCREW COLLAR LOOP
FIXTURE GROUND WIRE
SUPPLY GROUND WIRE
9. BLACK SUPPLY WIRE
10. SMOOTH FIXTURE LEAD WIRE
11. WHITE SUPPLY WIRE
12. RIBBED FIXTURE LEAD WIRE
13. WIRE CONNECTOR
14. GROUND SCREW
15. CANOPY
16. THREADED RING
17. CHAIN
18. FIXTURE LOOP
19. SAFETY CABLE
20. STRUCTURE SUPPORT BEAM